Set layer mode of operation (live or dma-based) during layer creation.
Each DPSUB layer mode of operation is defined by corresponding DT node port
connection, so it is possible to assign it during layer object creation.
Previously it was set in layer enable functions, although it is too late
as setting layer format depends on layer mode, and should be done before
given layer enabled.
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkainen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-1-c7f379b7168e@amd.com
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The "msg" pointer is a struct and msg->offset is the sizeof(*msg). The
pointer here math means the memcpy() will write outside the bounds.
Cast "msg" to a u8 pointer to fix this.
Fixes: 02c19d84c7 ("firmware: arm_ffa: Add support for FFA_MSG_SEND2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/cd5fb6b5-81fa-4a6d-b2b8-284ca704bbff@moroto.mountain
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With deferred IO enabled, a page fault happens when data is written to the
framebuffer device. Then driver determines which page is being updated by
calculating the offset of the written virtual address within the virtual
memory area, and uses this offset to get the updated page within the
internal buffer. This page is later copied to hardware (thus the name
"deferred IO").
This offset calculation is only correct if the virtual memory area is
mapped to the beginning of the internal buffer. Otherwise this is wrong.
For example, if users do:
mmap(ptr, 4096, PROT_WRITE, MAP_FIXED | MAP_SHARED, fd, 0xff000);
Then the virtual memory area will mapped at offset 0xff000 within the
internal buffer. This offset 0xff000 is not accounted for, and wrong page
is updated.
Correct the calculation by using vmf->pgoff instead. With this change, the
variable "offset" will no longer hold the exact offset value, but it is
rounded down to multiples of PAGE_SIZE. But this is still correct, because
this variable is only used to calculate the page offset.
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Closes: https://lore.kernel.org/linux-fbdev/271372d6-e665-4e7f-b088-dee5f4ab341a@oracle.com
Fixes: 56c134f7f1 ("fbdev: Track deferred-I/O pages in pageref struct")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240423115053.4490-1-namcao@linutronix.de
Intel pre-USB4 routers only have ROUTER_CS_0 up to ROUTER_CS_4 and it
immediately follows the TMU router registers. Correct this accordingly.
Reported-by: Rajaram Regupathy <rajaram.regupathy@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Directories do not support direct I/O and thus no non-blocking direct
I/O either. Open code the shutdown check and call to generic_file_open
instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-4-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Directories have non of the capabilities, so drop the flags. Note that
the current state is harmless as no one actually checks for the flags
either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-3-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Re-wrap the newly added fop_flags fields to not go over 80 characters.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-2-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
RIFSC is a peripheral firewall controller that filter accesses based on
Arm TrustZone secure state, Arm CPU privilege execution level and
Compartment IDentification of the STM32 SoC subsystems.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
cpu_feature_enabled(X86_FEATURE_OSPKE) does not necessarily reflect
whether CR4.PKE is set on the CPU. In particular, they may differ on
non-BSP CPUs before setup_pku() is executed. In this scenario, RDPKRU
will #UD causing the system to hang.
Fix by checking CR4 for PKE enablement which is always correct for the
current CPU.
The scenario happens by inserting a WARN* before setup_pku() in
identiy_cpu() or some other diagnostic which would lead to calling
__show_regs().
[ bp: Massage commit message. ]
Signed-off-by: David Kaplan <david.kaplan@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240421191728.32239-1-bp@kernel.org
In our production environment, after removing monitor groups, those
unused RMIDs get stuck in the limbo list forever because their
llc_occupancy is always larger than the threshold. But the unused RMIDs
can be successfully freed by turning up the threshold.
In order to know how much the threshold should be, perf can be used to
acquire the llc_occupancy of RMIDs in each rdt domain.
Instead of using perf tool to track llc_occupancy and filter the log
manually, it is more convenient for users to use tracepoint to do this
work. So add a new tracepoint that shows the llc_occupancy of busy RMIDs
when scanning the limbo list.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240408092303.26413-3-haifeng.xu@shopee.com
Now only the pseudo-locking part uses tracepoints to do event tracking,
but other parts of resctrl may need new tracepoints. It is unnecessary
to create separate header files and define CREATE_TRACE_POINTS in
different c files which fragments the resctrl tracing.
Therefore, give the resctrl tracepoint header file a generic name to
support its use for tracepoints that are not specific to pseudo-locking.
No functional change.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240408092303.26413-2-haifeng.xu@shopee.com
Daniel Machon says:
====================
net: sparx5: add support for port mirroring
This series adds support for port mirroring, and port mirroring stats,
through tc matchall action FLOW_ACTION_MIRRED.
The hardware has three independent mirroring probes. Each probe can be
configured with a separate set of filtering conditions that must be
fulfilled before traffic is mirrored.
A mirror probe can have up to 64 source ports and a single monitor port.
The direction of a mirror probe determines if rx or tx traffic is
mirrored from the source port to the monitor port.
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Lars Povlsen <lars.povlsen@microchip.com>
To: Steen Hegelund <Steen.Hegelund@microchip.com>
To: UNGLinuxDriver@microchip.com
To: Russell King <linux@armlinux.org.uk>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Yue Haibing <yuehaibing@huawei.com>
---
Changes in v3:
- Ditch do_div() (patch #3) to fix warning on hexagon arch, reported by intel bot
- Link to v2: https://lore.kernel.org/r/20240418-port-mirroring-v2-0-20642868b386@microchip.com
Changes in v2:
- Fix clang build warning about uninitialized variable 'err'
- Link to v1: https://lore.kernel.org/r/20240418-port-mirroring-v1-0-e05c35007c55@microchip.com
====================
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tc matchall mirror stats. When a new matchall mirror
rule is added, the baseline stats for that port is saved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary tc glue to add and delete mirror rules through tc
matchall.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports three independent mirroring probes. Each probe can
be configured to mirror rx or tx traffic (direction).
Using tc matchall, it is now possible to add a source port and a monitor
port to a mirror probe. Depending on the mirror direction, rx or tx
traffic from a source port will be mirrored to the monitor port.
A single source port can be a member of multiple mirror probes.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new tc matchall rules, we add a bit of bookkeeping
code to keep track of them. The rules are identified by the cookie
passed from the tc stack.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for port mirroring support through tc matchall, add the
required register definitions.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subtract in this condition is reversed. The ->length is the length
of the buffer. The ->bytesused is how many bytes we have copied thus
far. When the condition is reversed that means the result of the
subtraction is always negative but since it's unsigned then the result
is a very high positive value. That means the overflow check is never
true.
Additionally, the ->bytesused doesn't actually work for this purpose
because we're not writing to "buf->mem + buf->bytesused". Instead, the
math to calculate the destination where we are writing is a bit
involved. You calculate the number of full lines already written,
multiply by two, skip a line if necessary so that we start on an odd
numbered line, and add the offset into the line.
To fix this buffer overflow, just take the actual destination where we
are writing, if the offset is already out of bounds print an error and
return. Otherwise, write up to buf->length bytes.
Fixes: 9cb2173e6e ("[media] media: Add stk1160 new driver (easycap replacement)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs need
the PER and IPG clocks to be functional, so add the clock entries.
This also fixes the following schema warning:
imx8qm-apalis-eval.dtb: jpegdec@58400000: 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Ensure that drivers set max_num_buffers to a value >= 32.
For now there is no reason for drivers to request a lower
limit and doing so might potentially cause userspace issues.
Note that the old check of > MAX_BUFFER_INDEX was pointless
since q->max_num_buffers was already limited to MAX_BUFFER_INDEX
or less.
Also add a sanity check in __vb2_init_fileio(), returning
-ENOSPC if a driver returns more than 32 buffers from
VIDIOC_REQBUFS with count = q->min_reqbufs_allocation.
The vb2_fileio_data struct only supports up to 32 buffers,
so we need a check there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The error that V4L2 returns when an attempt is made to open an
unregisted device node is ENODEV, no ENXIO. Update the documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
If the CEC device is unregistered, then an attempt to open
the device node should result in an -ENODEV error instead of
-ENXIO.
Document this as well in cec-func-open.rst.
This is consistent with the error code returned by other
file operations such as ioctl.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the new V4L2 device node was registered, some additional
initialization was done before the device node was marked as
'registered'. During the time between creating the device node
and marking it as 'registered' it was possible to open the
device node, which would return -ENODEV since the 'registered'
flag was not yet set.
Hold the videodev_lock mutex from just before the device node
is registered until the 'registered' flag is set. Since v4l2_open
will take the same lock, it will wait until this registration
process is finished. This resolves this race condition.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: <stable@vger.kernel.org> # for vi4.18 and up
The per-resource MSR update functions cat_wrmsr(), mba_wrmsr_intel(),
and mba_wrmsr_amd() all take three arguments:
(struct rdt_domain *d, struct msr_param *m, struct rdt_resource *r)
struct msr_param contains pointers to both struct rdt_resource and struct
rdt_domain, thus only struct msr_param is necessary.
Pass struct msr_param as a single parameter. Clean up formatting and
fix some fir tree declaration ordering.
No functional change.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Maciej Wieczor-Retman <maciej.wieczor-retman@intel.com>
Link: https://lore.kernel.org/r/20240308213846.77075-3-tony.luck@intel.com
reset_all_ctrls() and resctrl_arch_update_domains() use on_each_cpu_mask()
to call rdt_ctrl_update() on potentially one CPU from each domain.
But this means rdt_ctrl_update() needs to figure out which domain to
apply changes to. Doing so requires a search of all domains in a resource,
which can only be done safely if cpus_lock is held. Both callers do hold
this lock, but there isn't a way for a function called on another CPU
via IPI to verify this.
Commit
c0d848fcb0 ("x86/resctrl: Remove lockdep annotation that triggers
false positive")
removed the incorrect assertions.
Add the target domain to the msr_param structure and call
rdt_ctrl_update() for each domain separately using
smp_call_function_single(). This means that rdt_ctrl_update() doesn't
need to search for the domain and get_domain_from_cpu() can safely
assert that the cpus_lock is held since the remaining callers do not use
IPI.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Maciej Wieczor-Retman <maciej.wieczor-retman@intel.com>
Link: https://lore.kernel.org/r/20240308213846.77075-2-tony.luck@intel.com
Breno Leitao says:
====================
allocate dummy device dynamically
struct net_device shouldn't be embedded into any structure, instead,
the owner should use the private space to embed their state into
net_device.
But, in some cases the net_device is embedded inside the private
structure, which blocks the usage of zero-length arrays inside
net_device.
Create a helper to allocate a dummy device at dynamically runtime, and
move the Ethernet devices to use it, instead of embedding the dummy
device inside the private structure.
This fixes all the network cases plus some wireless drivers.
PS: Due to lack of hardware, unfortunately most these patches are
compiled tested only, except ath11k that was kindly tested by Kalle Valo.
---
Changelog:
v7:
* Document the return value of alloc_netdev_dummy()
v6:
* No code change. Just added Reviewed-by: and fix a commit message
v5:
* Added a new patch to fix some typos in the previous code
* Rebased to net-net/main
v4:
* Added a new patch to add dummy device at free_netdev(), as suggested
by Jakub.
* Added support for some wireless driver.
* Added some Acked-by and Reviewed-by.
v3:
* Use free_netdev() instead of kfree() as suggested by Jakub.
* Change the free_netdev() place in ipa driver, as suggested by
Alex Elder.
* Set err in the error path in the Marvell driver, as suggested
by Simon Horman.
v2:
* Patch 1: Use a pre-defined name ("dummy#") for the dummy
net_devices.
* Patch 2-5: Added users for the new helper.
v1:
* https://lore.kernel.org/all/20240327200809.512867-1-leitao@debian.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath11k_ext_irq_grp by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath11k_ahb_config_ext_irq() for ahb, and
ath11k_pcic_ext_irq_config() for pcic.
The free of the device occurs at ath11k_ahb_free_ext_irq() for the ahb
case, and ath11k_pcic_free_ext_irq() for the pcic case.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath10k by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath10k_core_create(). The free of the device occurs
at ath10k_core_destroy().
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a new dummy netdev allocator, use it instead of
alloc_netdev()/init_dummy_netdev combination.
Using alloc_netdev() with init_dummy_netdev might cause some memory
corruption at the driver removal side.
Fixes: 61cdb09ff7 ("wifi: qtnfmac: allocate dummy net_device dynamically")
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is impossible to use init_dummy_netdev together with alloc_netdev()
as the 'setup' argument.
This is because alloc_netdev() initializes some fields in the net_device
structure, and later init_dummy_netdev() memzero them all. This causes
some problems as reported here:
https://lore.kernel.org/all/20240322082336.49f110cc@kernel.org/
Split the init_dummy_netdev() function in two. Create a new function called
init_dummy_netdev_core() that does not memzero the net_device structure.
Then have init_dummy_netdev() memzero-ing and calling
init_dummy_netdev_core(), keeping the old behaviour.
init_dummy_netdev_core() is the new function that could be called as an
argument for alloc_netdev().
Also, create a helper to allocate and initialize dummy net devices,
leveraging init_dummy_netdev_core() as the setup argument. This function
basically simplify the allocation of dummy devices, by allocating and
initializing it. Freeing the device continue to be done through
free_netdev()
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dummy devices, exit earlier at free_netdev() instead of executing
the whole function. This is necessary, because dummy devices are
special, and shouldn't have the second part of the function executed.
Otherwise reg_state, which is NETREG_DUMMY, will be overwritten and
there will be no way to identify that this is a dummy device. Also, this
device do not need the final put_device(), since dummy devices are not
registered (through register_netdevice()), where the device reference is
increased (at netdev_register_kobject()/device_add()).
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bad grammar in description of init_dummy_netdev() function. This
topic showed up in the review of the "allocate dummy device dynamically"
patch set.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arınç ÜNAL says:
====================
MT7530 DSA Subdriver Improvements Act IV
This is the forth patch series with the goal of simplifying the MT7530 DSA
subdriver and improving support for MT7530, MT7531, and the switch on the
MT7988 SoC.
I have done a simple ping test to confirm basic communication on all switch
ports on MCM and standalone MT7530, and MT7531 switch with this patch
series applied.
MT7621 Unielec, MCM MT7530:
rgmii-only-gmac0-mt7621-unielec-u7621-06-16m.dtb
gmac0-and-gmac1-mt7621-unielec-u7621-06-16m.dtb
tftpboot 0x80008000 mips-uzImage.bin; tftpboot 0x83000000 mips-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootm 0x80008000 0x83000000 0x83f00000
MT7622 Bananapi, MT7531:
gmac0-and-gmac1-mt7622-bananapi-bpi-r64.dtb
tftpboot 0x40000000 arm64-Image; tftpboot 0x45000000 arm64-rootfs.cpio.uboot; tftpboot 0x4a000000 $dtb; booti 0x40000000 0x45000000 0x4a000000
MT7623 Bananapi, standalone MT7530:
rgmii-only-gmac0-mt7623n-bananapi-bpi-r2.dtb
gmac0-and-gmac1-mt7623n-bananapi-bpi-r2.dtb
tftpboot 0x80008000 arm-zImage; tftpboot 0x83000000 arm-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootz 0x80008000 0x83000000 0x83f00000
This patch series finalises the patch series linked below.
https://lore.kernel.org/r/20230522121532.86610-1-arinc.unal@arinc9.com
---
Changes in v2:
- Add two new patches to the end.
- Patch 13
- Add the missing patch log.
- Link to v1: https://lore.kernel.org/r/20240419-for-netnext-mt7530-improvements-4-v1-0-6d852ca79b1d@arinc9.com
====================
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike MT7531BE, the GPIO 6-12 pins are not used for RGMII on MT7531AE.
Therefore, the GPIO 11-12 pins are set to function as MDC and MDIO to
expose the MDIO bus of the switch. Replace the comment with a better
explanation.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7531_rgmii_setup() function does not use the port variable, do not
pass the variable to it.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use priv->ds->num_ports on all for loops which configure the switch
registers. In the future, the value of MT7530_NUM_PORTS will depend on
priv->id. Therefore, this change prepares the subdriver for a simpler
implementation.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac_port_validate member of the mt753x_info structure is not being
used, remove it. Improve the member description section in the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530_PMEEECR_P() register is on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMEEECR_P(). Use the
FIELD_PREP and FIELD_GET macros. Rename GET_LPI_THRESH() and
SET_LPI_THRESH() to LPI_THRESH_GET() and LPI_THRESH_SET().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of checking whether functions are filled properly. priv->info which
is an mt753x_info structure is filled and checked for before this check.
It's unnecessary checking whether it's filled properly.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of the MT7988 SoC switch, the MAC speed capabilities
defined on mt753x_phylink_get_caps() won't apply to all switch models
anymore. Move them to more appropriate locations instead of overwriting
config->mac_capabilities.
Remove the comment on mt753x_phylink_get_caps() as it's become invalid with
the support of MT7531 and MT7988 SoC switch.
Add break to case 6 of mt7988_mac_port_get_caps() to be explicit.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7530_setup_mdio() and mt7531_setup_common() functions should be
checked for errors. Return if the functions return a non-zero value.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
