We have a MAC component (which is inside the SoC) and it has several
different HW steps. 3 bits used to be enough but now we need 4-bits
to represent all the different steps.
Properly support 4-bits in the MAC step value by refactoring all the
current handling of the MAC step/dash.
Already from family 8000 and up the dash (bits 0-1) no longer exists
and the step (until 8000 bits 2-3) consists of the dash bits as well.
To do this remove the CSR_HW_REV_STEP and the CSR_HW_REV_DASH
macros, replace them with CSR_HW_REV_STEP_DASH and add hw_rev_step
into the trans struct.
In addition remove the CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP and
CSR_HW_IF_CONFIG_REG_MSK_MAC_DASH macros and create a new macro
combining the 2 (this way we don't need shifting or anything else.)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Mike Golant <michael.golant@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211207160459.2e81a14d1f80.Ia5287e37fb3439d805336837361f6491f958e465@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we happen to decide an NSSN queue sync (IWL_MVM_RXQ_NSSN_SYNC)
for some remaining packets that are still on the queue, but just
after we've decided to do a delBA (which causes its own queues
sync with IWL_MVM_RXQ_NOTIF_DEL_BA) we can end up with a sequence
of events like this:
CPU 1 CPU 2
remove BA session with baid N
send IWL_MVM_RXQ_NOTIF_DEL_BA
send IWL_MVM_RXQ_NSSN_SYNC
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NSSN_SYNC
complete IWL_MVM_RXQ_NOTIF_DEL_BA
remove N from baid_map[]
get IWL_MVM_RXQ_NSSN_SYNC
WARN_ON(!baid_map[N])
Thus, there's a race that leads in hitting the WARN_ON, but more
importantly, it's a race that potentially even results in a new
aggregation session getting assigned to baid N.
To fix this, remove the WARN_ON() in the NSSN_SYNC case, we can't
completely protect against hitting this case, so we shouldn't be
warning. However, guard ourselves against BAID reuse by doing yet
another round of queue synchronization after the entry is removed
from the baid_map, so that it cannot be reused with any in-flight
IWL_MVM_RXQ_NSSN_SYNC messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083237.44abbbc50f40.I5492600dfe513356555abe2d7df0e2835846e3d8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes the following W=1 kernel build warning:
drivers/net/wireless/intel/iwlwifi/mvm/rfi.c:11: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
[removed the static const fix, since it's already done and
updated the commit message accordingly.]
Link: https://lore.kernel.org/r/20210517050141.61488-7-shenyang39@huawei.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_txq_dyn_alloc_dma, txq->tfds is freed at first time by:
iwl_txq_alloc()->goto err_free_tfds->dma_free_coherent(). But
it forgot to set txq->tfds to NULL.
Then the txq->tfds is freed again in iwl_txq_dyn_alloc_dma by:
goto error->iwl_txq_gen2_free_memory()->dma_free_coherent().
My patch sets txq->tfds to NULL after the first free to avoid the
double free.
Fixes: 0cd1ad2d7f ("iwlwifi: move all bus-independent TX functions to common code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210403054755.4781-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Smatch spot a possible NULL pointer dereference. Fix it.
__iwl_mvm_mac_set_key can be called with sta = NULL
Also add a NULL pointer check after memory allocation.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20211130105951.85539-1-emmanuel.grumbach@intel.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If CSME is compromised, it could report a bigger queue size
in the share area and make the host perform an out of bound
access.
Instead of reading the size of the queue from the shared area,
store it in the regular context which is not accessible by CSME.
While at it, fix a small typo in an error print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20211128121509.3952-1-emmanuel.grumbach@intel.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use named struct in struct mwl8k_cmd_set_key around members key_material,
tkip_tx_mic_key, and tkip_rx_mic_key so they can be referenced
together. This will allow memcpy() and sizeof() to more easily reason
about sizes, improve readability, and avoid future warnings about writing
beyond the end of key_material.
"pahole" shows no size nor member offset changes to struct
mwl8k_cmd_set_key. "objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119004905.2348143-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct hfa384x_tx_frame around members
frame_control, duration_id, addr1, addr2, addr3, and seq_ctrl, so they
can be referenced together. This will allow memcpy() and sizeof() to
more easily reason about sizes, improve readability, and avoid future
warnings about writing beyond the end of frame_control.
"pahole" shows no size nor member offset changes to struct
hfa384x_tx_frame. "objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119004646.2347920-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field array bounds checking for memcpy(), memmove(), and memset(),
avoid intentionally writing across neighboring fields.
Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of tx_dest_addr_high.
"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184121.1283821-1-keescook@chromium.org
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of queue_id.
"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184104.1283637-1-keescook@chromium.org
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
When freeing rx_cb->rx_skb, the pointer is not set to NULL,
a later rsi_rx_done_handler call will try to read the freed
address.
This bug will very likley lead to double free, although
detected early as use-after-free bug.
The bug is triggerable with a compromised/malfunctional usb
device. After applying the patch, the same input no longer
triggers the use-after-free.
Attached is the kasan report from fuzzing.
BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb]
Read of size 4 at addr ffff8880188e5930 by task modprobe/231
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__kasan_report.cold+0x37/0x7c
? dma_direct_unmap_page+0x90/0x110
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
kasan_report+0xe/0x20
rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __usb_hcd_giveback_urb+0x380/0x380
? apic_timer_interrupt+0xa/0x20
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
? handle_irq_event+0xcd/0x157
? handle_edge_irq+0x1eb/0x7b0
irq_exit+0x114/0x140
do_IRQ+0x91/0x1e0
common_interrupt+0xf/0xf
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
When entering suspend as a client station with wowlan enabled,
the Wi-Fi link is supposed to be maintained. In that state, no
more data is generated from client side, and the link stays idle
as long the station is suspended and as long the AP as no data to
transmit.
However, most of the APs kick-off such 'inactive' stations after
few minutes, causing unexpected disconnect (reconnect, etc...).
The usual way to prevent this is to submit a Null function frame
periodically as a keep-alive. This is something that can be host
/software generated (e.g. wpa_supplicant), but that needs to be
offloaded to the Wi-Fi controller in case of suspended host.
This change enables firmware generated keep-alive frames when
entering wowlan suspend, using the 'mkeep_alive' IOVAR.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637596046-21651-1-git-send-email-loic.poulain@linaro.org
Remove unused variables to avoid the below warnings:
drivers/net/wireless/microchip/wilc1000/wlan.c: In function 'chip_wakeup':
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:34: warning: variable 'to_host_from_fw_bit' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:13: warning: variable 'to_host_from_fw_reg' set but not used [-Wunused-but-set-variable]
620 | u32 to_host_from_fw_reg, to_host_from_fw_bit;
| ^~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115102809.1408267-1-ajay.kathat@microchip.com
Read the rfkill state upon boot, mac start and mac stop.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-6-emmanuel.grumbach@intel.com
Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.
* Send information on the AP CSME is connected to
* Notify the userspace when roaming is forbidden
* Allow the userspace to require ownership
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v6: remove the VENDOR_CMDS Kconfig option and make the whole infra
depend on IWLMEI directly
v7: remove // comments
remove an unneeded function
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-5-emmanuel.grumbach@intel.com
iwlmei needs to know about the follwing events:
* Association
* De-association
* Country Code change
* SW Rfkill change
* SAR table changes
iwlmei can take the device away from us, so report the new
rfkill type when this happens.
Advertise the required data from the CSME firmware to the
usersapce: mostly, the AP that the CSME firmware is currently
associated to in case there is an active link protection
session.
Generate the HOST_ASSOC / HOST_DISSASSOC messages.
Don't support WPA1 (non-RSNA) for now.
Don't support shared wep either.
We can then determine the AUTH parameter by checking the AKM.
Feed the cipher from the key installation.
SW Rfkill will be implemented later when cfg80211 will
allow us to read the SW Rfkill state.
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v7: Ayala added her signed-off
remove pointless function declaration
fix a bug due to merge conflict in the HOST_ASSOC message
v8: leave a print if we have a SAP connection on a device we do
not support (yet)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-4-emmanuel.grumbach@intel.com
Add three debugfs hooks:
* status: Check if we have a connection with the CSME
firwmare. This hook is a read only.
* req_ownership: Send a SAP command to request ownership. This
flow should be triggered by iwlwifi (from user space through
vendor commands really), but being able to trigger an ownership
request from debugfs allows us to request ownership without
connecting afterwards. This is an "error" flow that the CSME
firmware is designed to handle this way:
+ Grant ownership since the host asked for it
+ Wait 3 seconds to let the host connect
+ If the host didn't connect, take the device back (forcefully).
+ Don't grant any new ownership request in the following 30
seconds.
This debugfs hook allows us to test this flow.
* send_start_message: Restart the communication with the CSME
firmware from the very beginning. At the very beginning (upon
iwlwifi start), iwlmei send a special message: SAP_ME_MSG_START.
This hook allows to send it again and this will retrigger the
whole flow. It is important to test this restart in the middle
of normal operation since it can happen (in case the CSME
firmware decided to reset for example).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-3-emmanuel.grumbach@intel.com
CSME in two words
-----------------
CSME stands for Converged Security and Management Engine. It is
a CPU on the chipset and runs a dedicated firmware.
AMT (Active Management Technology) is one of the applications
that run on that CPU. AMT allows to control the platform remotely.
Here is a partial list of the use cases:
* View the screen of the plaform, with keyboard and mouse (KVM)
* Attach a remote IDE device
* Have a serial console to the device
* Query the state of the platform
* Reset / shut down / boot the platform
Networking in CSME
------------------
For those uses cases, CSME's firmware has an embedded network
stack and is able to use the network devices of the system: LAN
and WLAN. This is thanks to the CSME's firmware WLAN driver.
One can add a profile (SSID / key / certificate) to the CSME's OS
and CSME will connect to that profile. Then, one can use the WLAN
link to access the applications that run on CSME (AMT is one of
them). Note that CSME is active during power state and power state
transitions. For example, it is possible to have a KVM session
open to the system while the system is rebooting and actually
configure the BIOS remotely over WLAN thanks to AMT.
How all this is related to Linux
--------------------------------
In Linux, there is a driver that allows the OS to talk to the
CSME firmware, this driver is drivers/misc/mei. This driver
advertises a bus that allows other kernel drivers or even user
space) to talk to components inside the CSME firmware.
In practice, the system advertises a PCI device that allows
to send / receive data to / from the CSME firmware. The mei
bus drivers in drivers/misc/mei is an abstration on top of
this PCI device.
The driver being added here is called iwlmei and talks to the
WLAN driver inside the CSME firmware through the mei bus driver.
Note that the mei bus driver only gives bus services, it doesn't
define the content of the communication.
Why do we need this driver?
--------------------------
CSME uses the same WLAN device that the OS is expecting to see
hence we need an arbitration mechanism. This is what iwlmei is
in charge of. iwlmei maintains the communication with the CSME
firmware's WLAN driver. The language / protocol that is used
between the CSME's firmware WLAN driver and iwlmei is OS agnostic
and is called SAP which stands for Software Abritration Protocol.
With SAP, iwlmei will be able to tell the CSME firmware's WLAN
driver:
1) Please give me the device.
2) Please note that the SW/HW rfkill state change.
3) Please note that I am now associated to X.
4) Please note that I received this packet.
etc...
There are messages that go the opposite direction as well:
1) Please note that AMT is en/disable.
2) Please note that I believe the OS is broken and hence I'll take
the device *now*, whether you like it or not, to make sure that
connectivity is preserved.
3) Please note that I am willing to give the device if the OS
needs it.
4) Please give me any packet that is sent on UDP / TCP on IP address
XX.XX.XX.XX and an port ZZ.
5) Please send this packet.
etc...
Please check drivers/net/wireless/intel/iwlwifi/mei/sap.h for the
full protocol specification.
Arbitration is not the only purpose of iwlmei and SAP. SAP also
allows to maintain the AMT's functionality even when the OS owns
the device. To connect to AMT, one needs to initiate an HTTP
connection to port 16992. iwlmei will listen to the Rx path and
forward (through SAP) to the CSME firmware the data it got. Then,
the embedded HTTP server in the chipset will reply to the request
and send a SAP notification to ask iwlmei to send the reply.
This way, AMT running on the CSME can still work.
In practice this means that all the use cases quoted above (KVM,
remote IDE device, etc...) will work even when the OS uses the
WLAN device.
How to disable all this?
---------------------------
iwlmei won't be able to do anything if the CSME's networking stack
is not enabled. By default, CSME's networking stack is disabled (this
is a BIOS setting).
In case the CSME's networking stack is disabled, iwlwifi will just
get access to the device because there is no contention with any other
actor and, hence, no arbitration is needed.
In this patch, I only add the iwlmei driver. Integration with
iwlwifi will be implemented in the next one.
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v2: fix a few warnings raised by the different bots
v3: rewrite the commit message
v4: put the debugfs content in a different patch
v5: fix a NULL pointer dereference upon DHCP TX if SAP is connected
since we now have the required cfg80211 bits in wl-drv-next, add
the RFKILL handling patch to this series.
v6: change the SAP API to inherit the values from iwl-mei.h removing
the need to ensure the values are equal with a BUILD_BUG_ON.
This was suggested by Arend
v7: * fix a locking issue in case of CSME firmware reset:
When the CSME firmware resets, we need to unregister the
netdev, first take the mutex, and only then, rely on it
being taken.
* Add a comment to explain why it is ok to have static variables
(iwlmei can't have more than a single instance).
* Add a define for 26 + 8 + 8
* Add a define SEND_SAP_MAX_WAIT_ITERATION
* make struct const
* Reword a bit the Kconfig help message
* Ayala added her Signed-off
* fixed an RCU annotation
v8: do not require ownership upfront, use NIC_OWNER instead. This fixes
a deadlock when CSME does not have the right WiFi FW.
Add more documentation about the owernship transition
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-2-emmanuel.grumbach@intel.com
Expose the client dma mapping via mei client bus interface.
The client dma has to be mapped before the device is enabled,
therefore we need to create device linking already during mapping
and we need to unmap after the client is disable hence we need to
postpone the unlink and flush till unmapping or when
destroying the device.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Co-developed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210420172755.12178-1-emmanuel.grumbach@intel.com
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-1-emmanuel.grumbach@intel.com
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
We assume at a few places that priv->version_str is 0-terminated, but
right now we trust the firmware that this is the case with the version
string we get from it.
Let's rather ensure this ourselves and replace the last character with
'\0'.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-4-verdre@v0yd.nl
The 88W8897 PCIe+USB card in the hardware revision 20 apparently has a
hardware issue where the card wakes up from deep sleep randomly and very
often, somewhat depending on the card activity, maybe the hardware has a
floating wakeup pin or something. This was found by comparing two MS
Surface Book 2 devices, where one devices wifi card experienced spurious
wakeups, while the other one didn't.
Those continuous wakeups prevent the card from entering host sleep when
the computer suspends. And because the host won't answer to events from
the card anymore while it's suspended, the firmwares internal power
saving state machine seems to get confused and the card can't sleep
anymore at all after that.
Since we can't work around that hardware bug in the firmware, let's
get the hardware revision string from the firmware and match it with
known bad revisions. Then disable auto deep sleep for those revisions,
which makes sure we no longer get those spurious wakeups.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-3-verdre@v0yd.nl
Since the version string we get from the firmware is always 128
characters long, use a define for this size instead of having the number
128 copied all over the place.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-2-verdre@v0yd.nl
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
8821CE causes random freezes on HP 250 G7 Notebook PC. Add a quirk
to disable pci ASPM capability.
Reported-by: rtl8821cerfe2 <rtl8821cerfe2@protonmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119052437.8671-1-pkshih@realtek.com
The management frame with high rate e.g. 24M may not be transmitted
smoothly in long range environment.
Add a debugfs to force to use the lowest basic rate
in order to debug the reachability of transmitting management frame.
obtain current setting
cat /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
force lowest rate:
echo 1 > /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-2-pkshih@realtek.com
By default the driver uses the 1M and 6M rate for managemnt frames
in 2G and 5G bands respectively. But when the basic rates is
configured from the mac80211, we need to send the management frames
according to the basic rates.
This commit makes the driver use the lowest basic rates to send
the management frames.
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-1-pkshih@realtek.com
The AXIDMA is tx/rx packet transmission between PCIE host
and device, and TX FIFO is MAC TX data.
We dump them to verify that these memory buffers are correct.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211122021129.4339-1-pkshih@realtek.com
The RF register array is used to help firmware to restore RF settings.
The original code can potentially access out of range, if the size is
between (RTW89_H2C_RF_PAGE_SIZE * RTW89_H2C_RF_PAGE_NUM + 1) to
((RTW89_H2C_RF_PAGE_SIZE + 1) * RTW89_H2C_RF_PAGE_NUM). Fortunately,
current used size doesn't fall into the wrong case, and the size will not
change if we don't update RF parameter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119055729.12826-1-pkshih@realtek.com
Fix the following coccicheck review:
./drivers/net/wireless/realtek/rtw89/mac.c: 1096: 5-8: Unneeded variable
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211110121135.151187-1-deng.changcheng@zte.com.cn
The conditional operator is unnecessary while assigning values to the
bool variables.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104061119.1685-1-ye.guojin@zte.com.cn
Start to configure entries with RTW89_QATAR, RTW89_UKRAINE, RTW89_CN.
Adjust some entries with explicit rtw89_regulatory instead of RTW89_WW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-5-pkshih@realtek.com
Update tx power limit table and tx power limit_ru table to R54.
Configure entries for MEXICO, CN, QATAR, and adjust some values
of original entries.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-4-pkshih@realtek.com
Support QATAR in rtw89_regulation_type and reorder the enum to align
realtek R58-R31 regulation definition. Besides, if an unassigned entry
of limit/limit_ru tables is read, return the corresponding WW value for
the unconfigured case.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-3-pkshih@realtek.com
This modification just replaces the number filled in the regd field
with the corresponding enum. No assignment of a value in a table is
changed. Doing this first is because the follow-up patches may adjust
the order of enum declarations.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-2-pkshih@realtek.com
ath.git patches for v5.17. Major changes:
ath10k
* fetch (pre-)calibration data via nvmem subsystem
ath11k
* enable 802.11 power save mode in station mode for qca6390 and wcn6855
* trace log support
* proper board file detection for WCN6855 based on PCI ids
* BSS color change support
The struct ath_hw member intr_txqs is never reset/assigned outside
of ath9k_hw_init_queues() and with the used bitwise-or in the interrupt
handling ar9002_hw_get_isr() accumulates all ever set interrupt flags.
Fix this by using a pure assign instead of bitwise-or for the
first line (note: intr_txqs is only evaluated in case ATH9K_INT_TX bit
is set).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211116220720.30145-1-ps.report@gmx.net
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd85133 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
Some hardware can do this so let's use that capability.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmGVguoACgkQJNaLcl1U
h9AepAf/fyvh/Kjl5Bzpz5uzOG97WcWkpJzAd23qRD+iwvRxdXP5SK+f2AabOlXk
03LaEdjuQwQfHBbolBa8fXpnt2BT7oKKIMbgyf0Lm6ScZZYNmRTS/0ZOWJT76yiT
Q0i7fdIa41yccVep1O6Ux7CBnBfSSmBeZ/HGws1kHu4SBBTDEGZgR3RNKzl4g97Z
TcPTlQIZl/C48basYtgPG1EN49u8MgM4rDRVzs2h6xnqTe6gydk+McW57E6hgZkW
0kLWpUEJuHpe3bTfx3SuG1XmSD5WoM5G20RGJOcfhHaX2D2DpMvTGJdNqNUCEG8t
XVOBkXPq2E3u3XYVQf93uFKRNIqgLA==
=q7bK
-----END PGP SIGNATURE-----
Merge tag 'regmap-no-bus-update-bits' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Mark Brown says:
===================
regmap: Allow regmap_update_bits() to be offloaded with no bus
Some hardware can do this so let's use that capability.
===================
Link: https://lore.kernel.org/all/YZWDOidBOssP10yS@sirena.org.uk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- devlink: don't throw an error if flash notification sent before
devlink visible
- page_pool: Revert "page_pool: disable dma mapping support...",
turns out there are active arches who need it
Current release - new code bugs:
- amt: cancel delayed_work synchronously in amt_fini()
Previous releases - regressions:
- xsk: fix crash on double free in buffer pool
- bpf: fix inner map state pruning regression causing program
rejections
- mac80211: drop check for DONT_REORDER in __ieee80211_select_queue,
preventing mis-selecting the best effort queue
- mac80211: do not access the IV when it was stripped
- mac80211: fix radiotap header generation, off-by-one
- nl80211: fix getting radio statistics in survey dump
- e100: fix device suspend/resume
Previous releases - always broken:
- tcp: fix uninitialized access in skb frags array for Rx 0cp
- bpf: fix toctou on read-only map's constant scalar tracking
- bpf: forbid bpf_ktime_get_coarse_ns and bpf_timer_* in tracing progs
- tipc: only accept encrypted MSG_CRYPTO msgs
- smc: transfer remaining wait queue entries during fallback,
fix missing wake ups
- udp: validate checksum in udp_read_sock() (when sockmap is used)
- sched: act_mirred: drop dst for the direction from egress to ingress
- virtio_net_hdr_to_skb: count transport header in UFO, prevent
allowing bad skbs into the stack
- nfc: reorder the logic in nfc_{un,}register_device, fix unregister
- ipsec: check return value of ipv6_skip_exthdr
- usb: r8152: add MAC passthrough support for more Lenovo Docks
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=tlqV
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, mac80211.
Current release - regressions:
- devlink: don't throw an error if flash notification sent before
devlink visible
- page_pool: Revert "page_pool: disable dma mapping support...",
turns out there are active arches who need it
Current release - new code bugs:
- amt: cancel delayed_work synchronously in amt_fini()
Previous releases - regressions:
- xsk: fix crash on double free in buffer pool
- bpf: fix inner map state pruning regression causing program
rejections
- mac80211: drop check for DONT_REORDER in __ieee80211_select_queue,
preventing mis-selecting the best effort queue
- mac80211: do not access the IV when it was stripped
- mac80211: fix radiotap header generation, off-by-one
- nl80211: fix getting radio statistics in survey dump
- e100: fix device suspend/resume
Previous releases - always broken:
- tcp: fix uninitialized access in skb frags array for Rx 0cp
- bpf: fix toctou on read-only map's constant scalar tracking
- bpf: forbid bpf_ktime_get_coarse_ns and bpf_timer_* in tracing
progs
- tipc: only accept encrypted MSG_CRYPTO msgs
- smc: transfer remaining wait queue entries during fallback, fix
missing wake ups
- udp: validate checksum in udp_read_sock() (when sockmap is used)
- sched: act_mirred: drop dst for the direction from egress to
ingress
- virtio_net_hdr_to_skb: count transport header in UFO, prevent
allowing bad skbs into the stack
- nfc: reorder the logic in nfc_{un,}register_device, fix unregister
- ipsec: check return value of ipv6_skip_exthdr
- usb: r8152: add MAC passthrough support for more Lenovo Docks"
* tag 'net-5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (96 commits)
ptp: ocp: Fix a couple NULL vs IS_ERR() checks
net: ethernet: dec: tulip: de4x5: fix possible array overflows in type3_infoblock()
net: tulip: de4x5: fix the problem that the array 'lp->phy[8]' may be out of bound
ipv6: check return value of ipv6_skip_exthdr
e100: fix device suspend/resume
devlink: Don't throw an error if flash notification sent before devlink visible
page_pool: Revert "page_pool: disable dma mapping support..."
ethernet: hisilicon: hns: hns_dsaf_misc: fix a possible array overflow in hns_dsaf_ge_srst_by_port()
octeontx2-af: debugfs: don't corrupt user memory
NFC: add NCI_UNREG flag to eliminate the race
NFC: reorder the logic in nfc_{un,}register_device
NFC: reorganize the functions in nci_request
tipc: check for null after calling kmemdup
i40e: Fix display error code in dmesg
i40e: Fix creation of first queue by omitting it if is not power of two
i40e: Fix warning message and call stack during rmmod i40e driver
i40e: Fix ping is lost after configuring ADq on VF
i40e: Fix changing previously set num_queue_pairs for PFs
i40e: Fix NULL ptr dereference on VSI filter sync
i40e: Fix correct max_pkt_size on VF RX queue
...
-----BEGIN PGP SIGNATURE-----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=ze0L
-----END PGP SIGNATURE-----
Merge tag 'for-5.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several xes and one old ioctl deprecation. Namely there's fix for
crashes/warnings with lzo compression that was suspected to be caused
by first pull merge resolution, but it was a different bug.
Summary:
- regression fix for a crash in lzo due to missing boundary checks of
the page array
- fix crashes on ARM64 due to missing barriers when synchronizing
status bits between work queues
- silence lockdep when reading chunk tree during mount
- fix false positive warning in integrity checker on devices with
disabled write caching
- fix signedness of bitfields in scrub
- start deprecation of balance v1 ioctl"
* tag 'for-5.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: deprecate BTRFS_IOC_BALANCE ioctl
btrfs: make 1-bit bit-fields of scrub_page unsigned int
btrfs: check-integrity: fix a warning on write caching disabled disk
btrfs: silence lockdep when reading chunk tree during mount
btrfs: fix memory ordering between normal and ordered work functions
btrfs: fix a out-of-bound access in copy_compressed_data_to_page()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmGWL+AACgkQnJ2qBz9k
QNnK3ggAtJLlaCwg4TxyIIGEWBP/KBKs2STLf80VDavhxZuplKKZ0o5/9IPZ2uu9
v9SgME4hnGpUNaECttVWqijT823SiIxA/4uFSBnN1hLlvPj2Wkwl0oRWb6vCFzZ5
OBUiZrycZKxEq78p2Ao8+FxeRsJ9RuXHnPkZULAqizkEue23d+gW33cO0x//UwB0
lB6i32yDqCmOAtLaT1Div5ttJ3oM/hGBbOURkh3YB7jV2MxojHX28ZjDv657S30k
lhpQwvmHF70jM7MPWbxtcbSTBdPKQdaF5+oDqpAFwDQn3nhEk1sjw6IrCUKr2NAK
Z+YFlRgv5eD+loRPEBVVU/6QrmfSEQ==
=ueAF
-----END PGP SIGNATURE-----
Merge tag 'fs_for_v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull UDF fix from Jan Kara:
"A fix for a long-standing UDF bug where we were not properly
validating directory position inside readdir"
* tag 'fs_for_v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix crash after seekdir
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYZZM2AAKCRCRxhvAZXjc
onQYAP4oKQBguYvFThF4H4VnJY1xoS/33rNOqwPumubdj/8P2AD9EFOegFKYBFr7
tCpokujZl3jZTOqV6h32JDQkPZB0kAc=
=AqiS
-----END PGP SIGNATURE-----
Merge tag 'fs.idmapped.v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull setattr idmapping fix from Christian Brauner:
"This contains a simple fix for setattr. When determining the validity
of the attributes the ia_{g,u}id fields contain the value that will be
written to inode->i_{g,u}id. When the {g,u}id attribute of the file
isn't altered and the caller's fs{g,u}id matches the current {g,u}id
attribute the attribute change is allowed.
The value in ia_{g,u}id does already account for idmapped mounts and
will have taken the relevant idmapping into account. So in order to
verify that the {g,u}id attribute isn't changed we simple need to
compare the ia_{g,u}id value against the inode's i_{g,u}id value.
This only has any meaning for idmapped mounts as idmapping helpers are
idempotent without them. And for idmapped mounts this really only has
a meaning when circular idmappings are used, i.e. mappings where e.g.
id 1000 is mapped to id 1001 and id 1001 is mapped to id 1000. Such
ciruclar mappings can e.g. be useful when sharing the same home
directory between multiple users at the same time.
Before this patch we could end up denying legitimate attribute changes
and allowing invalid attribute changes when circular mappings are
used. To even get into this situation the caller must've been
privileged both to create that mapping and to create that idmapped
mount.
This hasn't been seen in the wild anywhere but came up when expanding
the fstest suite during work on a series of hardening patches. All
idmapped fstests pass without any regressions and we're adding new
tests to verify the behavior of circular mappings.
The new tests can be found at [1]"
Link: https://lore.kernel.org/linux-fsdevel/20211109145713.1868404-2-brauner@kernel.org [1]
* tag 'fs.idmapped.v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fs: handle circular mappings correctly
