The current code does some odd +1 over maximum xri count checks and
requires that the lun_queue_count can't be bigger than maximum xri count
divided by 8. These items are bogus.
Clean the code up to cap lun_queue_count to maximum xri count.
Link: https://lore.kernel.org/r/20200128002312.16346-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was report of an odd "Fix me..." log message, which was tracked down
to the lpfc_els_rcv_rps() routine. This was in handling of a very old and
obsolete ELS - Read Port Status. The RPS ELS was defined in FC-LS-1, but
deprecated in FC-LS-2, and removed from all later FC-LS revisions. It was
replaced by the Read Diagnostic Parameters (RDP) ELS and the Link Error
Status Block descriptor.
There should be no support for the RSP ELS. Remove support from driver.
Link: https://lore.kernel.org/r/20200128002312.16346-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported a memory corruption error for the fdmi attributes
routines:
CID 15768 [Memory Corruption] Out-of-bounds access on FDMI
Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and
lpfc_fdmi_reg_port_list structures, a field was placed at the start of
payload that may have variable content. The field was given an arbitrary
type (uint32_t). The code then uses the field name to derive an address,
which it used in things such as memset and memcpy. The memset sizes or
memcpy lengths were larger than the arbitrary type, thus coverity reported
an error.
Fix by replacing the arbitrary fields with the real field structures
describing the payload.
Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following error is see from the compiler:
drivers/scsi/lpfc/lpfc_init.c: In function
‘lpfc_cpuhp_get_eq’: drivers/scsi/lpfc/lpfc_init.c:12660:1:
error: the frame size of 1032 bytes is larger than 1024 bytes
[-Werror=frame-larger-than=]
The issue is due to allocating a cpumask on the stack.
Fix by converting to a dynamical allocation of the cpu mask.
Link: https://lore.kernel.org/r/20200128002312.16346-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When performing reset testing, the eq's list for related hwqs was getting
corrupted. In cases where there is not a 1:1 eq to hwq, the eq is
shared. The eq maintains a list of hwqs utilizing it in case of cpu
offlining and polling. During the reset, the hwqs are being torn down so
they can be recreated. The recreation was getting confused by seeing a
non-null eq assignment on the eq and the eq list became corrupt.
Correct by clearing the hdwq eq assignment when the hwq is cleaned up.
Link: https://lore.kernel.org/r/20200128002312.16346-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust FC4 Types in FDMI settings
The driver sets FDMI information registring ELS as a FC4 type. ELS is a
fc3 type and should not be registered.
Fix by removing ELS type bit when we register for FDMI Port attributes.
Link: https://lore.kernel.org/r/20200128002312.16346-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver is set to enable bb credit recovery, the switch displayed the
setting as inactive. If the link bounces, it switches to Active.
During link up processing, the driver currently does a MBX_READ_SPARAM
followed by a MBX_CONFIG_LINK. These mbox commands are queued to be
executed, one at a time and the completion is processed by the worker
thread. Since the MBX_READ_SPARAM is done BEFORE the MBX_CONFIG_LINK, the
BB_SC_N bit is never set the the returned values. BB Credit recovery status
only gets set after the driver requests the feature in CONFIG_LINK, which
is done after the link up. Thus the ordering of READ_SPARAM needs to follow
the CONFIG_LINK.
Fix by reordering so that READ_SPARAM is done after CONFIG_LINK. Added a
HBA_DEFER_FLOGI flag so that any FLOGI handling waits until after the
READ_SPARAM is done so that the proper BB credit value is set in the FLOGI
payload.
Fixes: 6bfb162082 ("scsi: lpfc: Fix configuration of BB credit recovery in service parameters")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a call to lpfc_get_cmd_rsp_buf_per_hdwq returns NULL (memory allocation
failure), a previously allocated lpfc_io_buf resource is leaked.
Fix by releasing the lpfc_io_buf resource in the failure path.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://lore.kernel.org/r/20200128002312.16346-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:
Port Status Event: ... error 1=0x52004a01, error 2=0x218
The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.
When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.
Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.
[mkp: typo]
Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Document the locking assumptions this function relies on and also verify
these locking assumptions at runtime.
Cc: Quinn Tran <qutran@marvell.com>
Cc: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20200123042345.23886-2-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not in use anymore. Remove the flag.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Link: https://lore.kernel.org/r/20200119071432.18558-3-ming.lei@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In current UFS driver design, hba->uic_link_state will not be changed after
link enters Hibern8 state by Auto-Hibern8 mechanism. In this case,
reference clock gating will be skipped unless special handling is
implemented in vendor's callbacks.
Support reference clock gating during Auto-Hibern8 period in MediaTek
Chipsets: If link state is already in Hibern8 while Auto-Hibern8 feature is
enabled, gate reference clock in setup_clocks callback.
Link: https://lore.kernel.org/r/20200129105251.12466-5-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Auto-Hibern8 may be disabled by some vendors or sysfs in runtime even if
Auto-Hibern8 capability is supported by host. If Auto-Hibern8 capability is
supported by host but not actually enabled, Auto-Hibern8 error shall not
happen.
To fix this, provide a way to detect if Auto-Hibern8 is actually enabled
first, and bypass Auto-Hibern8 disabling case in
ufshcd_is_auto_hibern8_error().
Fixes: 8217444039 ("scsi: ufs: Add error-handling of Auto-Hibernate")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200129105251.12466-4-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If system suspend or runtime suspend mode is configured as linkoff state,
phy can be powered off and reference clock can be gated in MediaTek
Chipsets.
At the same time, remove redundant reference clock control in suspend and
resume callbacks because such control can be well-handled in setup_clocks
callback.
Link: https://lore.kernel.org/r/20200129105251.12466-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek Chipsets can enter proprietary UniPro low-power mode during
suspend while link is in hibern8 state. Make sure leaving low-power mode
before every link startup to prevent lockup in any possible error recovery
path.
At the same time, re-factor related funcitons to improve code readability.
Link: https://lore.kernel.org/r/20200129105251.12466-2-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two statements that are indented one level too deeply, remove
the extraneous tabs.
[mkp: fix typo spotted by Bart]
Link: https://lore.kernel.org/r/20200126154757.42530-1-colin.king@canonical.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Connection failure processing depends on a daemon being present to (at
least) stop the connection and start recovery. This is a problem on a
multipath scenario, where if the daemon failed for whatever reason, the
SCSI path is never marked as down, multipath won't perform the failover and
IO to the device will be forever waiting for that connection to come back.
This patch performs the connection failure entirely inside the kernel.
This way, the failover can happen and pending IO can continue even if the
daemon is dead. Once the daemon comes alive again, it can execute recovery
procedures if applicable.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Lee Duncan <LDuncan@suse.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20200125061925.191601-1-krisman@collabora.com
Co-developed-by: Dave Clausen <dclausen@google.com>
Co-developed-by: Nick Black <nlb@google.com>
Co-developed-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Co-developed-by: Anatol Pomazau <anatol@google.com>
Co-developed-by: Tahsin Erdogan <tahsin@google.com>
Co-developed-by: Frank Mayhar <fmayhar@google.com>
Co-developed-by: Junho Ryu <jayr@google.com>
Co-developed-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Reviewed-by: Khazhismel Kumykov <khazhy@google.com>
Co-developed-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Bharath Ravi <rbharath@google.com>
Signed-off-by: Dave Clausen <dclausen@google.com>
Signed-off-by: Nick Black <nlb@google.com>
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Anatol Pomazau <anatol@google.com>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: Junho Ryu <jayr@google.com>
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce code duplication by introducing the tcm_qla2xxx_{get,rel}_cmd()
functions. Introduce these functions in the tcm_qla2xxx.c source files such
that the qla_target.c source file becomes independent of the SCSI target
core header files. This patch fixes a bug, namely by ensuring that
qlt_alloc_qfull_cmd() sets cmd->se_cmd.map_tag.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20200103192719.205158-1-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the checking, buffer reserve and buffer commit code in
synth_event_trace_start/end() into inline functions
__synth_event_trace_start/end() so they can also be used by
synth_event_trace() and synth_event_trace_array(), and then have all
those functions use them.
Also, change synth_event_trace_state.enabled to disabled so it only
needs to be set if the event is disabled, which is not normally the
case.
Link: http://lkml.kernel.org/r/b1f3108d0f450e58192955a300e31d0405ab4149.1581374549.git.zanussi@kernel.org
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There's no reason to return -EINVAL when tracing a synthetic event if
it's soft disabled - treat it the same as if it were hard disabled and
return normally.
Have synth_event_trace() and synth_event_trace_array() just return
normally, and have synth_event_trace_start set the trace state to
disabled and return.
Link: http://lkml.kernel.org/r/df5d02a1625aff97c9866506c5bada6a069982ba.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad95 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If the ring_buffer reserve in synth_event_trace_start() fails, the
matching ring_buffer_nest_end() should be called in the error code,
since nothing else will ever call it in this case.
Link: http://lkml.kernel.org/r/20abc444b3eeff76425f895815380abe7aa53ff8.1581374549.git.zanussi@kernel.org
Fixes: 8dcc53ad95 ("tracing: Add synth_event_trace() and related functions")
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The resctrl selftest will be maintained by RDT maintainers.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
For now, disable MBA and MBM tests for AMD. Deciding test pass/fail
is not clear right now. We can enable when we have some clarity.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
RESCTRL feature is supported both on Intel and AMD now. Some features
are implemented differently. Add vendor detection mechanism. Use the vendor
check where there are differences.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cache Allocation Technology (CAT) selftest allocates a portion of
last level cache and starts a benchmark to read each cache
line in this portion of cache. Measure the cache misses in perf and
the misses should be equal to the number of cache lines in this
portion of cache.
We don't use CQM to calculate cache usage because some CAT enabled
platforms don't have CQM.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cache QoS Monitoring (CQM) selftest starts stressful cache benchmark
with specified size of memory to access the cache. Last Level cache
occupancy reported by CQM should be close to the size of the memory.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
MBA (Memory Bandwidth Allocation) test starts a stressful memory
bandwidth benchmark and allocates memory bandwidth from 100% down
to 10% for the benchmark process. For each allocation, compare
perf IMC counter and mbm total bytes from resctrl. The difference
between the two values should be within a threshold to pass the test.
Default benchmark is built-in fill_buf. But users can specify their
own benchmark by option "-b".
We can add memory bandwidth allocation for multiple processes in the
future.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
MBM (Memory Bandwidth Monitoring) test is the first implemented selftest.
It starts a stressful memory bandwidth benchmark and assigns the
bandwidth pid in a resctrl monitoring group. Read and compare perf IMC
counter and MBM total bytes for the benchmark. The numbers should be
close enough to pass the test.
Default benchmark is built-in fill_buf. But users can specify their
own benchmark by option "-b".
We can add memory bandwidth monitoring for multiple processes in the
future.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Built-in benchmark fill_buf generates stressful memory bandwidth
and cache traffic.
Later it will be used as a default benchmark by various resctrl tests
such as MBA (Memory Bandwidth Allocation) and MBM (Memory Bandwidth
Monitoring) tests.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The callback starts a child process and puts the child pid in created
resctrl group with specified memory bandwidth in schemata. The child
starts running benchmark.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Total memory bandwidth can be monitored from perf IMC counter and from
resctrl file system. Later the two will be compared to verify the total
memory bandwidth read from resctrl is correct.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Currently the cursor is placed on the first overlay plane, which means
it will be at the bottom of the stack when the hw does the compositing
with anything other than primary plane. Since mtk doesn't support plane
zpos, change the cursor location to the top-most plane.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
The cursor and primary planes were hard coded.
Now search for them for passing to drm_crtc_init_with_planes
Signed-off-by: Evan Benn <evanbenn@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Pull cgroup fix from Tejun Heo:
"I made a mistake while removing cgroup task list lazy init
optimization making the root cgroup.procs show entries for the
init_tasks. The zero entries doesn't cause critical failures but does
make systemd print out warning messages during boot.
Fix it by omitting init_tasks as they should be"
* 'for-5.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: init_tasks shouldn't be linked to the root cgroup
With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:
make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127
Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)
Also, separate handling of each of the lists to its own shell command.
The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 5f70bde26a ("selftests: fix build behaviour on targets' failures")
added a logic to track failure of builds of individual targets. However, it
does exactly the opposite of what a distro kernel needs: we create a RPM
package with a selected set of selftests and we need the build to fail if
build of any of the targets fail.
Both use cases are valid. A distribution kernel is in control of what is
included in the kernel and what is being built; any error needs to be
flagged and acted upon. A CI system that tries to build as many tests as
possible on the best effort basis is not really interested in a failure here
and there.
Support both use cases by introducing a FORCE_TARGETS variable. It is
switched off by default to make life for CI systems easier, distributions
can easily switch it on while building their packages.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
tpm2 tests set fails if there is no /dev/tpm0 and /dev/tpmrm0
supported. Check if these files exist before run and mark test as
skipped in case of absence.
Signed-off-by: Nikita Sobolev <Nikita.Sobolev@synopsys.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
While running the ftracetests, the pid filter test failed because the
instance "foo" existed, and it was using it to rerun the test under a
instance named foo. The collision caused the test to fail as the mkdir
failed as the name already existed.
As of commit b5b77be812 ("selftests: ftrace: Allow some tests to be run
in a tracing instance") all a selftest needs to do to be tested in an
instance is to set the "instance" flag. There's no reason a selftest needs
to create an instance to run its test in an instance directly.
Remove the open coded testing in an instance for the pid filter test and
have it set the "instance" flag instead.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
There is a spelling mistake in a literal string, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=0cTj
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20200210' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux fixes from Paul Moore:
"Two small fixes: one fixes a locking problem in the recently merged
label translation code, the other fixes an embarrassing 'binderfs' /
'binder' filesystem name check"
* tag 'selinux-pr-20200210' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix sidtab string cache locking
selinux: fix typo in filesystem name
Fix a missing newline in a code block that was causing a warning:
Documentation/dev-tools/kunit/usage.rst:553: WARNING: Error in "code-block" directive:
maximum 1 argument(s) allowed, 3 supplied.
.. code-block:: bash
modprobe example-test
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
dma-bufs are device coherent, with explicit CPU synchronisation provided
via the begin/end cpu access ioctls. As the coherency of the dma-buf is
explicitly defined to be under user control, flushing any caches on
attach/detach of the dma-buf is additional work that doesn't aide the
user in the slightest.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dongwon Kim <dongwon.kim@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171130180702.29357-1-chris@chris-wilson.co.uk
I have an experimental setup where almost every possible system
service (even early startup ones) runs in separate namespace, using a
dedicated, minimal file system. In process of minimizing the contents
of the file systems with regards to modules and firmware files, I
noticed that in my system, the firmware files are loaded from three
different mount namespaces, those of systemd-udevd, init and
systemd-networkd. The logic of the source namespace is not very clear,
it seems to depend on the driver, but the namespace of the current
process is used.
So, this patch tries to make things a bit clearer and changes the
loading of firmware files only from the mount namespace of init. This
may also improve security, though I think that using firmware files as
attack vector could be too impractical anyway.
Later, it might make sense to make the mount namespace configurable,
for example with a new file in /proc/sys/kernel/firmware_config/. That
would allow a dedicated file system only for firmware files and those
need not be present anywhere else. This configurability would make
more sense if made also for kernel modules and /sbin/modprobe. Modules
are already loaded from init namespace (usermodehelper uses kthreadd
namespace) except when directly loaded by systemd-udevd.
Instead of using the mount namespace of the current process to load
firmware files, use the mount namespace of init process.
Link: https://lore.kernel.org/lkml/bb46ebae-4746-90d9-ec5b-fce4c9328c86@gmail.com/
Link: https://lore.kernel.org/lkml/0e3f7653-c59d-9341-9db2-c88f5b988c68@gmail.com/
Signed-off-by: Topi Miettinen <toiwoton@gmail.com>
Link: https://lore.kernel.org/r/20200123125839.37168-1-toiwoton@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e567cb3fef30 ("MAINTAINERS: add an entry for kfifo") added a new
entry to MAINTAINERS. Following the example of the previous entry on the
list I added a trailing ':' character at the end of the title line.
This however results in rather strange looking output from
scripts/get_maintainer.pl:
$ ./scripts/get_maintainer.pl ./0001-kfifo.patch
Stefani Seibold <stefani@seibold.net> (maintainer:KFIFO:)
linux-kernel@vger.kernel.org (open list)
It turns out there are more entries like this. Fix the entire file by
removing all trailing colons.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200130135515.30359-1-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
kernel/bpf/btf.c:4131:5: warning: symbol 'btf_check_func_type_match' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200210011441.147102-1-yaohongbo@huawei.com
Reduce the amount of work we do to verify client blt correctness as
currently our 0.5s subtests takes about 15s on slower devices!
v2: Grow the maximum block size until we run out of time
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200210231047.810929-1-chris@chris-wilson.co.uk
