As per the user manual, look like mod clock is not mandatory
for all Allwinner MIPI DSI controllers, it is connected to
CLK_DSI_SCLK for A31 and not available in A64.
So, add compatible check for A31 and get mod clock accordingly.
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-4-jagan@amarulasolutions.com
The MIPI DSI PHY controller on Allwinner A64 is similar
on the one on A31.
Add A64 compatible and append A31 compatible as fallback.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-3-jagan@amarulasolutions.com
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so it is valid
to have separate compatible for A64 on the same driver.
DSI_SCLK uses mod clock-names on dt-bindings, so the same
is not required for A64.
On that note
- A64 require minimum of 1 clock like the bus clock
- A33 require minimum of 2 clocks like both bus, mod clocks
So, update dt-bindings so-that it can document both A33,
A64 bindings requirements.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-2-jagan@amarulasolutions.com
Clang patch [0] enables emitting relocatable generic ALU/ALU64 instructions
(i.e, shifts and arithmetic operations), as well as generic load/store
instructions. The former ones are already supported by libbpf as is. This
patch adds further support for load/store instructions. Relocatable field
offset is encoded in BPF instruction's 16-bit offset section and are adjusted
by libbpf based on target kernel BTF.
These Clang changes and corresponding libbpf changes allow for more succinct
generated BPF code by encoding relocatable field reads as a single
ST/LDX/STX instruction. It also enables relocatable access to BPF context.
Previously, if context struct (e.g., __sk_buff) was accessed with CO-RE
relocations (e.g., due to preserve_access_index attribute), it would be
rejected by BPF verifier due to modified context pointer dereference. With
Clang patch, such context accesses are both relocatable and have a fixed
offset from the point of view of BPF verifier.
[0] https://reviews.llvm.org/D71790
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191223180305.86417-1-andriin@fb.com
A64 has 3 thermal sensors: 1 for CPU, 2 for GPU.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, one for CPU, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is just one sensor for the CPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are three sensors, two for each CPU cluster, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In sdma_tx_status() we must first find the current sdma_desc. In cyclic
mode we assume that this can always be found with vchan_find_desc().
This is true because do not remove the current descriptor from the
desc_issued list:
/*
* Do not delete the node in desc_issued list in cyclic mode, otherwise
* the desc allocated will never be freed in vchan_dma_desc_free_list
*/
if (!(sdmac->flags & IMX_DMA_SG_LOOP))
list_del(&vd->node);
We will change this in the next step, so check if the current descriptor is
the desired one also for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-9-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename sdma_disable_channel_async() after the hook it implements, like
done for all other functions in the SDMA driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-8-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
vchan_dma_desc_free_list() basically open codes vchan_vdesc_fini() in its
loop body. Call it directly rather than duplicating the code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-7-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All list operations are protected by &vc->lock. As vchan_vdesc_fini()
is called unlocked add the missing locking around the list operations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-6-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
vchan_vdesc_fini() shouldn't be called under a spin_lock. This is done
in two places, once in vchan_terminate_vdesc() and once in
vchan_synchronize(). Instead of freeing the vdesc right away, collect
the aborted vdescs on a separate list and free them along with the other
vdescs. The terminated descs are also freed in vchan_synchronize as done
before this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-5-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
vchan_dma_desc_free_list() basically open codes vchan_vdesc_fini() in
the loop body. One difference is an additional debug message. As this
isn't overly useful remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-4-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Originally freeing descriptors was split into a locked and an unlocked
part. The locked part in vchan_get_all_descriptors() collected all
descriptors on a separate list_head. This was done to allow iterating
over that new list in vchan_dma_desc_free_list() without a lock held.
This became broken in 13bb26ae88 ("dmaengine: virt-dma: don't always
free descriptor upon completion"). With this commit
vchan_dma_desc_free_list() no longer exclusively operates on the
separate list, but starts to put descriptors which can be reused back on
&vc->desc_allocated. This list operation should have been locked, but
wasn't.
In the mean time drivers started to call vchan_dma_desc_free_list() with
their lock held so that we now have the situation that
vchan_dma_desc_free_list() is called locked from some drivers and
unlocked from others.
To clean this up we have to do two things:
1. Add missing locking in vchan_dma_desc_free_list()
2. Make sure drivers call vchan_dma_desc_free_list() unlocked
This needs to be done atomically, so in this patch the locking is added
and all drivers are fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Green Wan <green.wan@sifive.com>
Tested-by: Green Wan <green.wan@sifive.com>
Link: https://lore.kernel.org/r/20191216105328.15198-3-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
vchan_vdesc_fini() can't be called locked. Instead, call
vchan_terminate_vdesc() which delays the freeing of the descriptor to
vchan_synchronize().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-2-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
error log for dma_channel_table_init() failure pointed a mere
"initialization failure", which is not very helpful message, so print
additional details like function name and error code.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We call dma_device_put() and module_put() after invoking
.device_free_chan_resources callback, but we should also take care of
router devices and invoke this after .route_free callback. So move it
after .route_free
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Richard Cochran says:
====================
Peer to Peer One-Step time stamping
This series adds support for PTP (IEEE 1588) P2P one-step time
stamping along with a driver for a hardware device that supports this.
If the hardware supports p2p one-step, it subtracts the ingress time
stamp value from the Pdelay_Request correction field. The user space
software stack then simply copies the correction field into the
Pdelay_Response, and on transmission the hardware adds the egress time
stamp into the correction field.
This new functionality extends CONFIG_NETWORK_PHY_TIMESTAMPING to
cover MII snooping devices, but it still depends on phylib, just as
that option does. Expanding beyond phylib is not within the scope of
the this series.
User space support is available in the current linuxptp master branch.
- Patch 1 adds phy_device methods for existing time stamping fields.
- Patches 2-5 convert the stack and drivers to the new methods.
- Patch 6 moves code around the dp83640 driver.
- Patches 7-10 add support for MII time stamping in non-PHY devices.
- Patch 11 adds the new P2P 1-step option.
- Patch 12 adds a driver implementing the new option.
Thanks,
Richard
Changed in v9:
~~~~~~~~~~~~~~
- Fix two more drivers' switch/case blocks WRT the new HWTSTAMP ioctl.
- Picked up two more review tags from Andrew.
Changed in v8:
~~~~~~~~~~~~~~
- Avoided adding forward functional declarations in the dp83640 driver.
- Picked up Florian's new review tags and another one from Andrew.
Changed in v7:
~~~~~~~~~~~~~~
- Converted pr_debug|err to dev_ variants in new driver.
- Fixed device tree documentation per Rob's v6 review.
- Picked up Andrew's and Rob's review tags.
- Silenced sparse warnings in new driver.
Changed in v6:
~~~~~~~~~~~~~~
- Added methods for accessing the phy_device time stamping fields.
- Adjust the device tree documentation per Rob's v5 review.
- Fixed the build failures due to missing exports.
Changed in v5:
~~~~~~~~~~~~~~
- Fixed build failure in macvlan.
- Fixed latent bug with its gcc warning in the driver.
Changed in v4:
~~~~~~~~~~~~~~
- Correct error paths and PTR_ERR return values in the framework.
- Expanded KernelDoc comments WRT PHY locking.
- Pick up Andrew's review tag.
Changed in v3:
~~~~~~~~~~~~~~
- Simplify the device tree binding and document the time stamping
phandle by itself.
Changed in v2:
~~~~~~~~~~~~~~
- Per the v1 review, changed the modeling of MII time stamping
devices. They are no longer a kind of mdio device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The InES at the ZHAW offers a PTP time stamping IP core. The FPGA
logic recognizes and time stamps PTP frames on the MII bus. This
patch adds a driver for the core along with a device tree binding to
allow hooking the driver to MII buses.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a PHY node, register its time stamper, if any, and attach
the instance to the PHY device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new binding that allows non-PHY MII time stamping
devices to find their buses. The new documentation covers both the
generic binding and one upcoming user.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While PHY time stamping drivers can simply attach their interface
directly to the PHY instance, stand alone drivers require support in
order to manage their services. Non-PHY MII time stamping drivers
have a control interface over another bus like I2C, SPI, UART, or via
a memory mapped peripheral. The controller device will be associated
with one or more time stamping channels, each of which sits snoops in
on a MII bus.
This patch provides a glue layer that will enable time stamping
channels to find their controlling device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming patch will change how the PHY time stamping functions are
registered with the networking stack, and adapting this driver would
entail adding forward declarations for four time stamping methods.
However, forward declarations are considered to be stylistic defects.
This patch avoids the issue by moving the probe and remove methods
immediately above the phy_driver interface structure.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp_ethss driver tests fields of the phy_device in order to
determine whether to defer to the PHY's time stamping functionality.
This patch replaces the open coded logic with an invocation of the
proper methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some parts of the networking stack and at least one driver test fields
within the 'struct phy_device' in order to query time stamping
capabilities and to invoke time stamping methods. This patch adds a
functional interface around the time stamping fields. This will allow
insulating the callers from future changes to the details of the time
stamping implemenation.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7216 uses a different reset controller name which is "rescal" instead
of "ahci", match the compatible string to account for that minor
difference, the reset is otherwise identical to how other generations of
SATA controllers work.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BCM7216 AHCI controller makes use of a specific reset controller
line/name, document the compatible string and the optional reset
properties.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make sure that we quiesce the controller and shut down the clocks in a
shutdown callback.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We were not managing the reset line during suspend/resume, but this
needs to be done to ensure that the controller can exit low power modes
correctly, especially with deep sleep suspend mode that may reset parts
of the logic.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae2 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f8297 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 6bb86fefa0
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In record defaults, if we emit a request we expect a context switck on
parking. We need take no further action, so don't even mess with the low
level engine->serial where it is not warranted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191225230703.2498794-1-chris@chris-wilson.co.uk
Taehee Yoo says:
====================
hsr: fix several bugs in hsr module
1. The first patch fixes debugfs warning when it's opened when hsr module
is being removed. debugfs file is opened, it tries to hold .owner module,
but it would print warning messages if it couldn't hold .owner module.
In order to avoid the warning message, this patch makes hsr module does
not set .owner. Unsetting .owner is safe because these are protected by
inode_lock().
2. The second patch fixes wrong error handling of hsr_dev_finalize()
a) hsr_dev_finalize() calls debugfs_create_{dir/file} to create debugfs.
it checks NULL pointer but debugfs don't return NULL so it's wrong code.
b) hsr_dev_finalize() calls register_netdevice(). so if it fails after
register_netdevice(), it should call unregister_netdevice().
But it doesn't.
c) debugfs doesn't affect any actual logic of hsr module.
So, the failure of creating of debugfs could be ignored.
3. The third patch adds hsr root debugfs directory.
When hsr interface is created, it creates debugfs directory in
/sys/kernel/debug/<interface name>.
It's a little bit faulty path because if an interface is the same with
another directory name in the same path, it will fail. If hsr root
directory is existing, the possibility of failure of creating debugfs
file will be reduced.
4. The fourth patch adds debugfs rename routine.
debugfs directory name is the same with hsr interface name.
So hsr interface name is changed, debugfs directory name should be
changed too.
5. The fifth patch fixes a race condition in node list add and del.
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
6. The Sixth patch resets network header
Tap routine is enabled, below message will be printed.
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
hsr module doesn't set network header for supervision frame.
But tap routine validates network header.
If network header wasn't set, it resets and warns about it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Splat looks like:
[ 236.066091][ T3286] list_add corruption. next->prev should be prev (ffff8880a5940300), but was ffff8880a5940d0.
[ 236.069617][ T3286] ------------[ cut here ]------------
[ 236.070545][ T3286] kernel BUG at lib/list_debug.c:25!
[ 236.071391][ T3286] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 236.072343][ T3286] CPU: 0 PID: 3286 Comm: arping Tainted: G W 5.5.0-rc1+ #209
[ 236.073463][ T3286] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 236.074695][ T3286] RIP: 0010:__list_add_valid+0x74/0xd0
[ 236.075499][ T3286] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 b
[ 236.078277][ T3286] RSP: 0018:ffff8880aaa97648 EFLAGS: 00010286
[ 236.086991][ T3286] RAX: 0000000000000075 RBX: ffff8880d4624c20 RCX: 0000000000000000
[ 236.088000][ T3286] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed1015552ebf
[ 236.098897][ T3286] RBP: ffff88809b53d200 R08: ffffed101b3c04f9 R09: ffffed101b3c04f9
[ 236.099960][ T3286] R10: 00000000308769a1 R11: ffffed101b3c04f8 R12: ffff8880d4624c28
[ 236.100974][ T3286] R13: ffff8880d4624c20 R14: 0000000040310100 R15: ffff8880ce17ee02
[ 236.138967][ T3286] FS: 00007f23479fa680(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 236.144852][ T3286] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 236.145720][ T3286] CR2: 00007f4a14bab210 CR3: 00000000a61c6001 CR4: 00000000000606f0
[ 236.146776][ T3286] Call Trace:
[ 236.147222][ T3286] hsr_add_node+0x314/0x490 [hsr]
[ 236.153633][ T3286] hsr_forward_skb+0x2b6/0x1bc0 [hsr]
[ 236.154362][ T3286] ? rcu_read_lock_sched_held+0x90/0xc0
[ 236.155091][ T3286] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 236.156607][ T3286] hsr_dev_xmit+0x70/0xd0 [hsr]
[ 236.157254][ T3286] dev_hard_start_xmit+0x160/0x740
[ 236.157941][ T3286] __dev_queue_xmit+0x1961/0x2e10
[ 236.158565][ T3286] ? netdev_core_pick_tx+0x2e0/0x2e0
[ ... ]
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: fc4ecaeebd ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
