This code changes the TI specific ti,fifo-depth to the common
tx-fifo-depth property. The tx depth is applicable for both RGMII and
SGMII modes of operation.
rx-fifo-depth was added as well but this is only applicable for SGMII
mode.
So in summary
if RGMII mode write tx fifo depth only
if SGMII mode write both rx and tx fifo depths
If the property is not populated in the device tree then set the value
to the default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the ti,fifo-depth from a TI specific property to the common
tx-fifo-depth property. Also add support for the rx-fifo-depth.
These are optional properties for this device and if these are not
available then the fifo depths are set to device default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Adrian Bunk <bunk@kernel.org>
CC: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a sysctl knob "net.ipv4.tcp_no_ssthresh_metrics_save"
that disables TCP ssthresh metrics cache by default. Other parts of TCP
metrics cache, e.g. rtt, cwnd, remain unchanged.
As modern networks becoming more and more dynamic, TCP metrics cache
today often causes more harm than benefits. For example, the same IP
address is often shared by different subscribers behind NAT in residential
networks. Even if the IP address is not shared by different users,
caching the slow-start threshold of a previous short flow using loss-based
congestion control (e.g. cubic) often causes the future longer flows of
the same network path to exit slow-start prematurely with abysmal
throughput.
Caching ssthresh is very risky and can lead to terrible performance.
Therefore it makes sense to make disabling ssthresh caching by
default and opt-in for specific networks by the administrators.
This practice also has worked well for several years of deployment with
CUBIC congestion control at Google.
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_acpi_dev_add_driver_gpios() returns -ENXIO if CONFIG_ACPI
is disabled (e.g. on device tree platforms).
In this case, nxp-nci will silently fail to probe.
The other NFC drivers only log a debug message if
devm_acpi_dev_add_driver_gpios() fails.
Do the same in nxp-nci to fix this problem.
Fixes: ad0acfd69a ("NFC: nxp-nci: Get rid of code duplication in ->probe()")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 312434617c ("sctp: cache netns in sctp_ep_common") set netns
in asoc and ep base since they're created, and it will never change.
It's a better way to get netns from asoc and ep base, comparing to
calling sock_net().
This patch is to replace them.
v1->v2:
- no change.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:
================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
call_timer_fn+0x132/0x470
__run_timers.part.0+0x39f/0x5b0
run_timer_softirq+0x63/0xc0
__do_softirq+0x12d/0x5fd
irq_exit+0xb3/0x110
smp_apic_timer_interrupt+0x131/0x3d0
apic_timer_interrupt+0xf/0x20
default_idle+0x31/0x230
arch_cpu_idle+0x13/0x20
default_idle_call+0x53/0x60
do_idle+0x38a/0x3f0
cpu_startup_entry+0x24/0x30
start_secondary+0x222/0x290
secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&session->frwd_lock)->rlock);
<Interrupt>
lock(&(&session->frwd_lock)->rlock);
*** DEADLOCK ***
2 locks held by kworker/7:1H/206:
#0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
#1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0
stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0xa5/0xe6
print_usage_bug.cold+0x232/0x23b
mark_lock+0x8dc/0xa70
__lock_acquire+0xcea/0x2af0
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
scsi_times_out+0xf4/0x440 [scsi_mod]
scsi_timeout+0x1d/0x20 [scsi_mod]
blk_mq_check_expired+0x365/0x3a0
bt_iter+0xd6/0xf0
blk_mq_queue_tag_busy_iter+0x3de/0x650
blk_mq_timeout_work+0x1af/0x380
process_one_work+0x56d/0xab0
worker_thread+0x7a/0x5d0
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Fixes: 287922eb0b ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch disables autohibern8 feature in Cadence UFS. The autohibern8
feature has issues due to which unexpected interrupt trigger is happening.
After the interrupt issue is sorted out, autohibern8 feature will be
re-enabled
Link: https://lore.kernel.org/r/1575367635-22662-1-git-send-email-sheebab@cadence.com
Cc: <stable@vger.kernel.org>
Signed-off-by: sheebab <sheebab@cadence.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->chap_dma_pool' double freed
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->fw_ddb_dma_pool' double freed
Fixes: afaf5a2d34 ("[SCSI] Initial Commit of qla4xxx")
Link: https://lore.kernel.org/r/20191203094421.hw7ex7qr3j2rbsmx@kili.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous preallocation and DIO decision like below.
allow_outplace_dio !allow_outplace_dio
f2fs_force_buffered_io (*) No_Prealloc / Buffered_IO Prealloc / Buffered_IO
!f2fs_force_buffered_io No_Prealloc / DIO Prealloc / DIO
But, Javier reported Case (*) where zoned device bypassed preallocation but
fell back to buffered writes in f2fs_direct_IO(), resulting in stale data
being read.
In order to fix the issue, actually we need to preallocate blocks whenever
we fall back to buffered IO like this. No change is made in the other cases.
allow_outplace_dio !allow_outplace_dio
f2fs_force_buffered_io (*) Prealloc / Buffered_IO Prealloc / Buffered_IO
!f2fs_force_buffered_io No_Prealloc / DIO Prealloc / DIO
Reported-and-tested-by: Javier Gonzalez <javier@javigon.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Through a somewhat convoluted series of changes, we have ended up
with multiple unnecessary occurrences of (flags & MAY_NOT_BLOCK)
tests in selinux_inode_permission(). Clean it up and simplify.
No functional change.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Considering there can be multiple UFS hosts in SoC, give each ufs-bsg an
unique ID by appending the scsi host number to its device name.
Link: https://lore.kernel.org/r/0101016eca8dc9d7-d24468d3-04d2-4ef3-a906-abe8b8cbcd3d-000000@us-west-2.amazonses.com
Fixes: df032bf27a ("scsi: ufs: Add a bsg endpoint that supports UPIUs")
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the Videostrong KII Pro tv box which is
based on the gxbb-p201 reference design
Device specifications:
- SOC: Amlogic S905
- RAM: 2GB DDR3
- Storage: 16GB
- Connectivity:
- 10/100M Ethernet (IC Plus IP101GR)
- 802.11 b/g/n/ac Wi-Fi (Ampak AP6335 BT/WIFI combo)
- Bluetooth 4.0 (Ampak AP6335 BT/WIFI combo)
- Video out: HDMI 2.0 up to 4K @ 60Hz, and 3.5mm AV (composite video) jack
- Audio out: HDMI, AV (stereo audio) and optical S/PDIF
- Tuner: AVL6862 DVB-C/T/T2 + DVB-S/S2 demod and Rafael Micro R848 tuner
- Ports:
- x1 micro SD card slot up to 32GB
- 4x USB 2.0 host ports
- Misc:
- Power button and LED, IR receiver
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the compatible for the Amlogic gxbb(s905) based kii pro
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Videostrong Technology Co., Ltd., A manufacturer of Android Players & STB
(Android with DVB Hybrid box & DVB-T2/S2/C/ISDB-T/DTMB-TH/ATSC) as well as
HD media players.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move SAM9X60's PM part under SoC config flag. This allows the building
of SAM9X60 platform withouth depending on CONFIG_SOC_AT91SAM9 flag,
allowing us to select only necessary config flags for SAM9X60.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1575035505-6310-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set the frequency of the generated clock used by sdmmc devices in order
to not rely on the configuration done by previous components.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20191128074522.69706-3-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
commit bda0be7ad9 ("security: make inode_follow_link RCU-walk aware")
passed down the rcu flag to the SELinux AVC, but failed to adjust the
test in slow_avc_audit() to also return -ECHILD on LSM_AUDIT_DATA_DENTRY.
Previously, we only returned -ECHILD if generating an audit record with
LSM_AUDIT_DATA_INODE since this was only relevant from inode_permission.
Move the handling of MAY_NOT_BLOCK to avc_audit() and its inlined
equivalent in selinux_inode_permission() immediately after we determine
that audit is required, and always fall back to ref-walk in this case.
Fixes: bda0be7ad9 ("security: make inode_follow_link RCU-walk aware")
Reported-by: Will Deacon <will@kernel.org>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The change adds a way to debug LOGO ELS, likewise PLOGI.
Link: https://lore.kernel.org/r/20191125165702.1013-14-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_configure_local_loop sets RELOGIN_NEEDED bit and calls
qla24xx_fcport_handle_login to perform the login. This bit triggers a wake
up of DPC later after a successful login.
The deferred call is not needed if login succeeds, and it's set in
qla24xx_fcport_handle_login in case of errors, hence it should be safe to
drop.
Link: https://lore.kernel.org/r/20191125165702.1013-12-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Acked-by: Quinn Tran <qutran@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a ("scsi: qla2xxx: Fix session cleanup for N2N")
Cc: Krishna Kant <krishna.kant@purestorage.com>
Cc: Alexei Potashnik <alexei@purestorage.com>
Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad0990 ("scsi: qla2xxx: Fix N2N link re-connect")
Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to FC-LS-3 (Fibre Channel Link Services) 6.3.2.4
"N_Port Login - No Fabric present", if both parties in the point-to-point
connection know N_Port_Names of each other, Nx_Port with the highest
N_Port_name shall transmit PLOGI. The specification sets no restrictions on
the port role that should send PLOGI.
However, FCP-4 (Fibre Channel Protocol for SCSI, Fourth Version) 6.2
"Overview of Process Login and Process Logout", instructs that in
point-to-point topology, initiator shall send explicit PRLI ELS.
The change fixes stuck P2P login, when target WWPN is higher than initiator
WWPN.
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-7-r.bolshakov@yadro.com
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port sends PLOGI, discovery state should be changed to login
pending, otherwise RELOGIN_NEEDED bit is set in
qla24xx_handle_plogi_done_event(). RELOGIN_NEEDED triggers another PLOGI,
and it never goes out of the loop until login timer expires.
Fixes: 8777e4314d ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Fixes: 8b5292bcfc ("scsi: qla2xxx: Fix Relogin to prevent modifying scan_state flag")
Cc: Quinn Tran <qutran@marvell.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-6-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cb ("scsi: qla2xxx: Move session delete to driver work queue")
Cc: Quinn Tran <qutran@marvell.com>
Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit e46e01eebb ("selinux: stop passing MAY_NOT_BLOCK
to the AVC upon follow_link"). The correct fix is to instead fall
back to ref-walk if audit is required irrespective of the specific
audit data type. This is done in the next commit.
Fixes: e46e01eebb ("selinux: stop passing MAY_NOT_BLOCK to the AVC upon follow_link")
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Target makes implicit LOGO on session teardown. LOGO ELS is not send on the
wire and initiator is not aware that target no longer wants talking to
it. Initiator keeps sending I/O requests, target responds with BA_RJT, they
time out and then initiator sends ABORT TASK (ABTS-LS).
Current behaviour incurs unneeded I/O timeout and can be fixed for some
initiators by making explicit LOGO on session deletion.
Link: https://lore.kernel.org/r/20191125165702.1013-3-r.bolshakov@yadro.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If ABTS cannot be completed in target mode, the driver attempts to free
related management command and crashes:
NIP [d000000019181ee8] tcm_qla2xxx_free_mcmd+0x40/0x80 [tcm_qla2xxx]
LR [d00000001dc1e6f8] qlt_response_pkt+0x190/0xa10 [qla2xxx]
Call Trace:
[c000003fff27bb50] [c000003fff27bc10] 0xc000003fff27bc10 (unreliable)
[c000003fff27bb70] [d00000001dc1e6f8] qlt_response_pkt+0x190/0xa10 [qla2xxx]
[c000003fff27bc10] [d00000001dbc2be0] qla24xx_process_response_queue+0x5d8/0xbd0 [qla2xxx]
[c000003fff27bd50] [d00000001dbc632c] qla24xx_msix_rsp_q+0x64/0x150 [qla2xxx]
[c000003fff27bde0] [c000000000187200] __handle_irq_event_percpu+0x90/0x310
[c000003fff27bea0] [c0000000001874b8] handle_irq_event_percpu+0x38/0x90
[c000003fff27bee0] [c000000000187574] handle_irq_event+0x64/0xb0
[c000003fff27bf10] [c00000000018cd38] handle_fasteoi_irq+0xe8/0x280
[c000003fff27bf40] [c000000000185ccc] generic_handle_irq+0x4c/0x70
[c000003fff27bf60] [c000000000016cec] __do_irq+0x7c/0x1d0
[c000003fff27bf90] [c00000000002a530] call_do_irq+0x14/0x24
[c00000207d2cba90] [c000000000016edc] do_IRQ+0x9c/0x130
[c00000207d2cbae0] [c000000000008bf4] hardware_interrupt_common+0x114/0x120
--- interrupt: 501 at arch_local_irq_restore+0x74/0x90
LR = arch_local_irq_restore+0x74/0x90
[c00000207d2cbdd0] [c0000000001c64fc] tick_broadcast_oneshot_control+0x4c/0x60 (unreliable)
[c00000207d2cbdf0] [c0000000007ac840] cpuidle_enter_state+0xf0/0x450
[c00000207d2cbe50] [c00000000016b81c] call_cpuidle+0x4c/0x90
[c00000207d2cbe70] [c00000000016bc30] do_idle+0x2b0/0x330
[c00000207d2cbec0] [c00000000016beec] cpu_startup_entry+0x3c/0x50
[c00000207d2cbef0] [c00000000004a06c] start_secondary+0x63c/0x670
[c00000207d2cbf90] [c00000000000aa6c] start_secondary_prolog+0x10/0x14
The crash can be triggered by ACL deletion when there's active I/O.
During ACL deletion, qla2xxx performs implicit LOGO that's invisible for
the initiator. Only the driver and firmware are aware of the logout.
Therefore the initiator continues to send SCSI commands and the target
always responds with SAM STATUS BUSY as it can't find the session.
The command times out after a while and initiator invokes ABORT TASK TMF
for the command. The TMF is mapped to ABTS-LS in FCP. The target can't find
session for S_ID originating ABTS-LS so it never allocates mcmd. And since
N_Port handle was deleted after LOGO, it is no longer valid and ABTS
Response IOCB is returned from firmware with status 31. Then free_mcmd is
invoked on NULL pointer and the kernel crashes.
[ 7734.578642] qla2xxx [0000:00:0c.0]-e837:6: ABTS_RECV_24XX: instance 0
[ 7734.578644] qla2xxx [0000:00:0c.0]-f811:6: qla_target(0): task abort (s_id=1:2:0, tag=1209504, param=0)
[ 7734.578645] find_sess_by_s_id: 0x010200
[ 7734.578645] Unable to locate s_id: 0x010200
[ 7734.578646] qla2xxx [0000:00:0c.0]-f812:6: qla_target(0): task abort for non-existent session
[ 7734.578648] qla2xxx [0000:00:0c.0]-e806:6: Sending task mgmt ABTS response (ha=c0000000d5819000, atio=c0000000d3fd4700, status=4
[ 7734.578730] qla2xxx [0000:00:0c.0]-e838:6: ABTS_RESP_24XX: compl_status 31
[ 7734.578732] qla2xxx [0000:00:0c.0]-e863:6: qla_target(0): ABTS_RESP_24XX failed 31 (subcode 19:a)
[ 7734.578740] Unable to handle kernel paging request for data at address 0x00000200
Fixes: 6b0431d6fa ("scsi: qla2xxx: Fix out of order Termination and ABTS response")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Thomas Abraham <tabraham@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191125165702.1013-2-r.bolshakov@yadro.com
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Certain ACPI-enumerated devices represented as platform devices in
Linux, like fans, require special low-level power management handling
implemented by their drivers that is not in agreement with the ACPI
PM domain behavior. That leads to problems with managing ACPI fans
during system-wide suspend and resume.
For this reason, make acpi_dev_pm_attach() skip the affected devices
by adding a list of device IDs to avoid to it and putting the IDs of
the affected devices into that list.
Fixes: e5cc8ef312 (ACPI / PM: Provide ACPI PM callback routines for subsystems)
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
add peripheral pinctrl controller to a1 SoC
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the reset controller device of Meson-A1 SoC family
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add gpio irq to support interrupt trigger mode.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)
Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.
Fixes: 79795e20a1 ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
pm_genpd_init() can return an error. Propagate the error code to prevent
the driver from indicating that it successfully probed while there were
errors during pm_genpd_init().
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
of_genpd_add_provider_onecell() can return an error. Propagate the error
so the driver registration fails when of_genpd_add_provider_onecell()
did not work.
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When phba->mbox_ext_buf_ctx.seqNum != phba->mbox_ext_buf_ctx.numBuf,
dd_data should be freed before return SLI_CONFIG_HANDLED.
When lpfc_sli_issue_mbox func return fails, pmboxq should be also freed in
job_error tag.
Link: https://lore.kernel.org/r/EDBAAA0BBBA2AC4E9C8B6B81DEEE1D6915E7A966@DGGEML525-MBS.china.huawei.com
Signed-off-by: Bo Wu <wubo40@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFUB length should be in DWORDs when passed to FW.
Fixes: 3f006ac342 ("scsi: qla2xxx: Secure flash update support for ISP28XX")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191203223657.22109-4-hmadhani@marvell.com
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
