Provide DT documentation for enable-gpios.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Static structure micro_bl_props, having type backlight_properties, is
used only once, when it is passed as the last argument to function
devm_backlight_device_register(). devm_backlight_device_register() is
defined with its last parameter being declared constant. Hence make
micro_bl_props itself constant as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Devicetree aliases are missing, so that module autoloading
does not work properly.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With this patch, the "interrupts" property from the device tree bindings
is ignored, even if present, if the driver runs in TCFQ mode.
Switching to using the DSPI in poll mode has several distinct
benefits:
- With interrupts, the DSPI driver in TCFQ mode raises an IRQ after each
transmitted word. There is more time wasted for the "waitq" event than
for actual I/O. And the DSPI IRQ count can easily get the largest in
/proc/interrupts on Freescale boards with attached SPI devices.
- The SPI I/O time is both lower, and more consistently so. Attached to
some Freescale devices are either PTP switches, or SPI RTCs. For
reading time off of a SPI slave device, it is important that all SPI
transfers take a deterministic time to complete.
- In poll mode there is much less time spent by the CPU in hardirq
context, which helps with the response latency of the system, and at
the same time there is more control over when interrupts must be
disabled (to get a precise timestamp measurement, which will come in a
future patch): win-win.
On the LS1021A-TSN board, where the SPI device is a SJA1105 PTP switch
(with a bits_per_word=8 driver), I created a "benchmark" where I
periodically transferred a 12-byte message once per second, for 120
seconds. I then recorded the time before putting the first byte in the
TX FIFO, and the time after reading the last byte from the RX FIFO. That
is the transfer delay in nanoseconds.
Interrupt mode:
delay: min 125120 max 168320 mean 150286 std dev 17675.3
Poll mode:
delay: min 69440 max 119040 mean 70312.9 std dev 8065.34
Both the mean latency and the standard deviation are more than 50% lower
in poll mode than in interrupt mode, and the 'max' in poll mode is lower
than the 'min' in interrupt mode. This is with an 'ondemand' governor on
an otherwise idle system - therefore running mostly at 600 MHz out of a
max of 1200 MHz.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191001205216.32115-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
User space always expects to be able to read ALSA controls, so ensure
no kcontrols are generated without an appropriate READ flag. In the case
of a read of such a control zeros will be returned.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191002084240.21589-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename arndale_rt5631.c to just arnddale.c as we support other CODECs
than RT5631. While at it replace spaces in Kconfig with tabs.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20191002105652.24821-3-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arndale boards come with different types of the audio daughter
board. In order to support the WM1811 one we add new definition of
an ASoC card which will be registered when the driver matches on
"samsung,arndale-wm1811" compatible. There is no runtime detection of
the audio daughter board type at the moment, compatible string of the
audio card needs to be adjusted in DT, e.g. by the bootloader,
depending on actual audio board (CODEC) used.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20191002105652.24821-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one DAI link so we can drop an unnecessary loop statement.
Use card->dai_link in place of direct static arndale_rt5631_dai[] array
dereference as a prerequisite for adding support for other CODECs.
Unnecessary assignment of dai_link->codecs->name to NULL is removed.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20191002105652.24821-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Split out the code related to vga client and vgaarb all over the place
into new intel_vga.[ch]. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001152506.7854-1-jani.nikula@intel.com
GPU PLL was designed with dynamic frequency switching in mind so driver
can adjust rate based on the GPU load.
Allow GPU clock to change parent rate (GPU PLL is the only possible
parent of GPU clock).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
IPQ4019 has a built in SD/eMMC controller which is supported by the
SDHCI MSM driver, by the "qcom,sdhci-msm-v4" binding.
So lets add the appropriate node for it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register a platform device to handle the communication of bus bandwidth
requests with the remote processor. The interconnect proxy device is part
of this remote processor (RPM) hardware. Let's create a icc-smd-rpm proxy
child device to represent the bus throughput functionality that is provided
by the RPM.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This makes way for adding future llcc versions.
Also pull out the llcc-qcom specific definitions from includes.
Includes path now contains the only definitions that are
to be exposed to other subsystems.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The cleaning up was done without changing the driver file name
to ensure a cleaner bisect. Change the file name now to facilitate
making the driver generic in subsequent patch.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A single file should suffice the need to program the llcc for
various platforms. Get rid of sdm845 specific driver file to
make way for a more generic driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We use a pinctrl "workaround" to toggle the UFS reset line. Now that UFS
controller can issue the reset, just specify the line as a GPIO and let
it be reset that way.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the DT nodes for the network-on-chip interconnect buses found
on qcs404-based platforms.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
msm8916.dtsi sets the iris compatible to "qcom,wcn3620".
While WCN3620 seems to be used on most MSM8916 devices,
MSM8916 can also be paired with another chip (e.g. for WiFi dual-band).
A5U uses WCN3660B instead, so the compatible needs to be overridden
to apply the correct configuration.
However, simply using "qcom,wcn3660" would be incorrect,
since WCN3660B requires a slightly different regulator configuration
compared to WCN3660.
Instead, it requires the same configuration as "qcom,wcn3680".
Replace the compatible with "qcom,wcn3680" for A5U to make WCNSS
work correctly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
WCNSS is used on A3U and A5U for WiFi and BT,
and seems to work fine without further changes.
Enable it in the common include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Allows QCS404 based designs to enable watchdog support
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This fixed rate clock is required for the operation of some devices
(ie watchdog).
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Initialize last_reset variable to INITIAL_JIFFIES, otherwise it is not
possible to test H/W reset for first 5 minutes of system run.
Fixes: e403fa31ed ("rt2x00: add restart hw")
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "priv->hw_type" is an enum and in this context GCC will treat it
as an unsigned int so the error handling will never trigger.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The module parameter rtw_fw_support_lps is misleading. It
is not used to represent the firmware's property, but to
determine if driver wants to ask firmware to enter LPS.
However, driver should better enable/disable PS through
cfg80211_ops::set_power_mgmt instead.
For example, one could use iw command to set PS state.
$ sudo iw wlanX set power_save [on/off]
So rtw_fw_support_lps should be removed because it is
misleading and useless. Instead of checking the parameter,
set PS mode according to IEEE80211_CONF_PS.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compare with LCLK mode, PG mode saves more power, by turning
off more circuits. Therefore, to recover from PG mode, driver
needs to backup some information into rsvd page. Such as CAM
entries, DPK results.
As CAM entries can change, it is required to re-download CAM
entries after set_key.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes LPS is not compatible with COEX's strategy, and
COEX will not allow driver to enter it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deep power save allows firmware/hardware to operate in a
lower power state. And the deep power save mode depends on
LPS mode. So, before entering deep PS, driver must first
enter LPS mode.
Under Deep PS, most of hardware functions are shutdown,
driver will not be able to read/write registers and transfer
data to the device. Hence TX path must be protected by each
interface. Take PCI for example, DMA engine should be idle,
and no nore activities on the PCI bus.
If driver wants to operate on the device, such as register
read/write, it must first acquire the mutex lock and wake
up from Deep PS, otherwise the behavior is undefined.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dynamic mechanism requires BB/RF working to adjust
hardware settings. But PS state periodically turns
off BB/RF, could lead to wrong setting.
So leave PS state before DM to make sure it works.
And then check if we can enter PS state again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Protect LPS enter/leave routine with rtwdev->mutex.
This helps to synchronize with driver's states correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The original design of LPS enter/leave routines allows
to control the LPS state by each interface. But the
hardware cannot actually handle it that way. This means
the hardware can only enter LPS once with an associated
port, so there is no need to keep tracking the state of
each vif.
Hence the logic of enter/leave LPS state can be simple,
just to check the state of the device's flag. And for
leaving LPS state, it will get the same port id to send
to inform the hardware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove PS related *_irqsafe functions to avoid entering/leaving PS
under interrupt context. Instead, make PS decision in watch_dog.
This could simplify the logic and make the code look clean.
But it could have a little side-effect that if the driver is having
heavy traffic before the every-2-second watch_dog detect the traffic
and decide to leave PS, the thoughput will be lower. Once traffic is
detected by watch_dog and left PS state, the throughput will resume
to the peak the hardware ought to have again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the driver doesn't reset the host's and device's indexes
in a single write, the indexes will become different in a
short period. And it will confuse the DMA engine, make it
start to process non-existed entries.
Better to Write-1-to-reset the indexes, for the DMA engine
to know that this is a reset of the H2C queue, not a kick
off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2255:7: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2254:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit a619d1abe2 ("rtlwifi:
rtl8723be: Add new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2805:34: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2804:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit b1a3bfc97c ("rtlwifi:
rtl8192ee: Move driver from staging to the regular tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:656:5: warning: variable short_gi set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:648:15: warning: variable buf_len set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_pg_packet_write:
drivers/net/wireless/realtek/rtlwifi/efuse.c:937:24: warning: variable dataempty set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_get_current_size:
drivers/net/wireless/realtek/rtlwifi/efuse.c:1202:5: warning: variable hoffset set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/ps.c: In function rtl_ps_set_rf_state:
drivers/net/wireless/realtek/rtlwifi/ps.c:71:19: warning: variable rtstate set but not used [-Wunused-but-set-variable]
It is not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
