[Why]
We don't want GSL to be enabled when only updating
plane address
[How]
Only check other pipes for immediate flip if GSL is
already enabled
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On DCE, the cursor is not being disabled on commits where there is no
CRTC or FB enabled.
[how]
Explicitly disable the cursor in the commit tail only if the pending
commit disables the CRTC.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to make sure all immediate flips are completed before locking
the pipes, but not pipes that are not flip immediate as they will be
locked by the OTG
[How]
Skip non flip immediate pipes when checking for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The intended use is to force PSR into active state and ignore all
events until explicit EXIT.
A new event force_static is added to power module. It is then sent
to FW.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, prefetch mode 0 is unsupported but prefetch 1 is
supported. Due to previous change always forcing prefetch mode to 0, we
are failing bandwidth validation in cases where we should not.
[How]
By default try prefetch mode 0 but in the case validation fails, attempt
to do prefetch mode 1 to see if it is supported.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a NULL pointer crash when DCN disabled on headless SKU.
On normal SKU, the variable adev->ddev.mode_config.funcs is
initialized in dm_hw_init(), and it is fine to access it in
amdgpu_device_resume(). But on headless SKU, DCN is disabled,
the funcs variable is not initialized, then crash arises.
Enable DCN to fix this issue.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are different platforms and devices which might use different scale
for the power values. Kernel sub-systems might need to check if all
Energy Model (EM) devices are using the same scale. Address that issue and
store the information inside EM for each device. Thanks to that they can
be easily compared and proper action triggered.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Quentin Perret <qperret@google.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[Why]
Prevent compiler warnings when building amdgpu kernel module
[How]
Add the include directive for amdgpu_amdkfd_gfx_v9 header file
Fixes: aeee2a48ec ("drm/amd/amdgpu: Enable arcturus devices to access the method kgd_gfx_v9_get_cu_occupancy that is already defined")
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
The way that bpmp_populate_debugfs_inband() uses strncpy()
and strncat() makes no sense since the size argument for
the first is insufficient to contain the trailing '/'
and the second passes the length of the input rather than
the output, which triggers a warning:
In function 'strncat',
inlined from 'bpmp_populate_debugfs_inband' at ../drivers/firmware/tegra/bpmp-debugfs.c:422:4:
include/linux/string.h:289:30: warning: '__builtin_strncat' specified bound depends on the length of the source argument [-Wstringop-overflow=]
289 | #define __underlying_strncat __builtin_strncat
| ^
include/linux/string.h:367:10: note: in expansion of macro '__underlying_strncat'
367 | return __underlying_strncat(p, q, count);
| ^~~~~~~~~~~~~~~~~~~~
drivers/firmware/tegra/bpmp-debugfs.c: In function 'bpmp_populate_debugfs_inband':
include/linux/string.h:288:29: note: length computed here
288 | #define __underlying_strlen __builtin_strlen
| ^
include/linux/string.h:321:10: note: in expansion of macro '__underlying_strlen'
321 | return __underlying_strlen(p);
Simplify this to use an snprintf() instead.
Fixes: 5e37b9c137 ("firmware: tegra: Add support for in-band debug")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently we are using dcn3 reg headers for dcn302. The offsets are
different between the two so they need seperate headers.
Add dcn302 header files and use these instead of dcn3 header
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In preparation to enabling hdcp on green sardine.
[How]
Add green-sardine ta f/w loading in psp_v12
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to the previous patch, clear shadow on suspend to avoid timeouts
waiting for ringbuffer space.
Fixes: 8907afb476 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clear the shadow rptr on suspend. Otherwise, when we resume, we can
have a stale value until CP_WHERE_AM_I executes. If we suspend near
the ringbuffer wraparound point, this can lead to a chicken/egg
situation where we are waiting for ringbuffer space to write the
CP_WHERE_AM_I (or CP_INIT) packet, because we mistakenly believe that
the ringbuffer is full (due to stale rptr value in the shadow).
Fixes errors like:
[drm:adreno_wait_ring [msm]] *ERROR* timeout waiting for space in ringbuffer 0
in the resume path.
Fixes: d3a569fccf ("drm/msm: a6xx: Use WHERE_AM_I for eligible targets")
Signed-off-by: Rob Clark <robdclark@chromium.org>
AMD Family 19h's RAPL MSRs are identical to Family 17h's. Extend
Family 17h's support to Family 19h.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Victor Ding <victording@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable AMD Fam17h RAPL support for the power capping framework.
The support is as per AMD Fam17h Model31h (Zen2) and model 00-ffh
(Zen1) PPR.
Tested by comparing the results of following two sysfs entries and the
values directly read from corresponding MSRs via /dev/cpu/[x]/msr:
/sys/class/powercap/intel-rapl/intel-rapl:0/energy_uj
/sys/class/powercap/intel-rapl/intel-rapl:0/intel-rapl:0:0/energy_uj
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Kim Phillips <kim.phillips@amd.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the static struct rapl_msr_priv to a pointer to allow using
a different RAPL MSR interface, preparing for supporting AMD's RAPL
MSR interface.
No functional changes.
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Kim Phillips <kim.phillips@amd.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSRs in the rest of this file are sorted by their addresses; fixing the
two outliers.
No functional changes.
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Life time related setting is related to WLAN active port number,
not its mode. The original setting may cause poor WLAN performance.
In most case, WLAN TX limitation is helpful for BT in coexistence
scenario, especially for A2DP quality.
So this is necessary to fix the setting and constraint it.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-12-pkshih@realtek.com
Since coexistence issue is related to WL/BT and each digital/analog/rf,
and these issues are often critical with low failure rate, add more
debugging information is helpful to clarify issues.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-11-pkshih@realtek.com
Adaptive Frequency Hopping(AFH) is a method of transmitting
radio signals by rapidly changing the carrier frequency among
many distinct frequencies, which can avoid interference.
Add this feature to update AFH parameter for 8822b.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-10-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Add counter to count BT info C2H command for debug usage.
It could present the C2H channel situation.
Fix BT IQK state decision condition for counting.
The original condition is wrong, it would cause coexistence mechanism
going to the wrong strategy.
New format supports getting TDMA parameter from WL firmware, since
coexistence needs current TDMA parameter to decide strategy.
Remove unnecessary operations about scoreboard, it is not a must for
current version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-8-pkshih@realtek.com
The original stop_dm flag is shared with the wifi and coexistence
mechanism internal usage, which represent two meanings, and makes
developers hard to debug.
Add a new flag manual_control for coexistence mechanism usage only.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-7-pkshih@realtek.com
To make sure the related ANT/RF_PARA setting will be expected result in COEX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-6-pkshih@realtek.com
Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com
Use macro definition to replace magic number.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-4-pkshih@realtek.com
Update COEX parameters and logic to enhance WL/BT performance
while WL_Busy + A2DP in a less interference environment.
It can avoid the interference comes cross from each other
and earned more performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-3-pkshih@realtek.com
Some register definition and bit definition were incorrect.
e.g. REG_BT_COEX_V2 should be word alignment to meet the coding style.
e.g. set REG_BT_TDMA_TIME[5:0]=0x5,
But the original is to set REG_BT_TDMA_TIME[7:0]=0x5.
This will cause unexpected hardware behavior.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-2-pkshih@realtek.com
The inner do { ... } while loop is completely useless, all it does
is iterate over a switch-case statement, one bit at a time. This
can easily be replaced by simple if (status & bit) { ... } tests
for each bit. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-2-marex@denx.de
The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.
The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."
The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.
This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.
Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.
So, let's update the comments at the top of each function accordingly.
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Detect and avoid this endless loop.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
On some platforms, the preset values aren't correct and then we may
get a completion timeout in the firmware. Change the LTR configuration
to avoid that. The firmware will do some more complex reinit of this
later, but for the boot process we use ~250usec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d83d591c05ba.I42885c9fb500bc08b9a4c07c4ff3d436cc7a3c84@changeid
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
We need to feed the configuration id to remove session protection
properly.
Remember the conf_id when we add the session protection so that we
can give it back when we want to remove the session protection.
While at it, slightly improve the kernel doc for the conf_id
of the notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.3642f730333d.I01a98ecde62096d00d171cf34ad775bf80cb0277@changeid
The ROC that runs on the AUX ROC (meaning an ROC on the STA vif),
was added with the HOT_SPOT_CMD firmware command and must be
cancelled with that same command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.a317376154da.I44fa3637373ba4bd421cdff2cabc761bffc0735f@changeid
Currently, our max tpt is limited to max HT A-MPDU for LB,
and max VHT A-MPDU for HB. Configure HE exponent value correctly to
achieve HE max A-MPDU, both on LB and HB.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.4486852ebb56.I9eb0d028e31f183597fb90120e7d4ca87e0dd6cb@changeid
This adds a validation function that scans the entire boot memory and makes
sure that all early memory sections are online. This check is essential for
the memory notifier to work properly, as it cannot prevent any boot memory
from offlining, if all sections are not online to begin with. Although the
boot section scanning is selectively enabled with DEBUG_VM.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-4-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This enables MEM_OFFLINE memory event handling. It will help intercept any
possible error condition such as if boot memory some how still got offlined
even after an explicit notifier failure, potentially by a future change in
generic hot plug framework. This would help detect such scenarios and help
debug further. While here, also call out the first section being attempted
for offline or got offlined.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This moves memory notifier registration earlier in the boot process from
device_initcall() to early_initcall() which will help in guarding against
potential early boot memory offline requests. Even though there should not
be any actual offlinig requests till memory block devices are initialized
with memory_dev_init() but then generic init sequence might just change in
future. Hence an early registration for the memory event notifier would be
helpful. While here, just skip the registration if CONFIG_MEMORY_HOTREMOVE
is not enabled and also call out when memory notifier registration fails.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As a hardening measure, we currently randomize the placement of
physical memory inside the linear region when KASLR is in effect.
Since the random offset at which to place the available physical
memory inside the linear region is chosen early at boot, it is
based on the memblock description of memory, which does not cover
hotplug memory. The consequence of this is that the randomization
offset may be chosen such that any hotplugged memory located above
memblock_end_of_DRAM() that appears later is pushed off the end of
the linear region, where it cannot be accessed.
So let's limit this randomization of the linear region to ensure
that this can no longer happen, by using the CPU's addressable PA
range instead. As it is guaranteed that no hotpluggable memory will
appear that falls outside of that range, we can safely put this PA
range sized window anywhere in the linear region.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201014081857.3288-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
