Commit graph

982,081 commits

Author SHA1 Message Date
Peter Chen
8cf8bde284 doc: dt-binding: mxs-usb-phy: add compatible for 7ulp
Add compatible for 7ulp USB PHY.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:56:16 +03:00
Fabio Estevam
fc4a903078 dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
This reverts commit 002905eca5.

Commit 002905eca5 ("dmaengine: fsl-edma: support little endian for edma
driver") incorrectly assumed that there was not little endian support
in the driver.

This causes hangs on Vybrid, so revert it so that Vybrid systems
could boot again.

Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2019-07-03 13:25:49 +05:30
Linus Walleij
f50dfaf772 misc: fsa9480: Delete this driver
The FSA9480 has a new driver more appropriately located
in the drivers/extcon subsystem. It is also more complete
and includes device tree support. Delete the old misc
driver.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Pawe Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20190630140302.16245-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03 09:51:08 +02:00
Pawel Laszczak
573aff747e usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.

Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.

To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.

The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.

Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.

Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.

Issue has been fixed for DEV_VER_V2 version of controller.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:46:07 +03:00
Pawel Laszczak
8bc1901ca7 usb:cdns3 Add Cadence USB3 DRD Driver
This patch introduce new Cadence USBSS DRD driver to Linux kernel.

The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.

The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.

The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:46:05 +03:00
Pawel Laszczak
c2af6b0780 usb:gadget Simplify usb_decode_get_set_descriptor function.
Patch moves switch responsible for decoding descriptor type
outside snprintf. It improves code readability a little.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:46:03 +03:00
Pawel Laszczak
ca888ce749 usb:gadget Patch simplify usb_decode_set_clear_feature function.
Patch adds usb_decode_test_mode and usb_decode_device_feature functions,
which allow to make more readable and simplify the
usb_decode_set_clear_feature function.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:46:01 +03:00
Pawel Laszczak
3db1b636c0 usb:gadget Separated decoding functions from dwc3 driver.
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
    dwc3_decode_get_status
    dwc3_decode_set_clear_feature
    dwc3_decode_set_address
    dwc3_decode_get_set_descriptor
    dwc3_decode_get_configuration
    dwc3_decode_set_configuration
    dwc3_decode_get_intf
    dwc3_decode_set_intf
    dwc3_decode_synch_frame
    dwc3_decode_set_sel
    dwc3_decode_set_isoch_delay
    dwc3_decode_ctrl

These functions are used also in inroduced cdns3 driver.

All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:45:58 +03:00
Pawel Laszczak
e8a8b40cc8 dt-bindings: add binding for USBSS-DRD controller.
This patch aim at documenting USB related dt-bindings for the
Cadence USBSS-DRD controller.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:45:56 +03:00
Felipe Balbi
b3649dee5f usb: dwc3: pci: add support for TigerLake Devices
This patch adds the necessary PCI ID for TGP-LP devices.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03 10:45:11 +03:00
Thomas Zimmermann
0ccf52badd drm/vram: Don't export driver callback functions for PRIME
PRIME functionality is now provided by GEM object functions. The driver
callback functions are obsolete. So this patch renames them and turns
them into static internal functions of the VRAM helper library. The
implementation of gem_prime_mmap is now unused and the patch removes it.

v3:
	* kept each renamed function at its original location within file
	* kept documentation

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702115012.4418-6-tzimmermann@suse.de
2019-07-03 09:32:36 +02:00
Thomas Zimmermann
bf2791eb5c drm/vbox: Remove empty PRIME functions
The vbox driver uses VRAM helpers for memory management. These helpers
provide a basic implementation of PRIME functions, so the vbox driver's
empty implmentation can be removed. As a side effect of this change,
vbox can now use generic framebuffer emulation.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702115012.4418-5-tzimmermann@suse.de
2019-07-03 09:32:27 +02:00
Thomas Zimmermann
80be7eed1d drm/hibmc: Update struct drm_driver for GEM object functions
The GEM object's free function is now called through struct
drm_gem_object_funcs.free. The function struct drm_driver.gem_prime_mmap
is now required for mmap'ing GEM objects to userspace.

v2:
	* set drm_driver.gem_prime_mmap to drm_gem_prime_mmap()

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702115012.4418-4-tzimmermann@suse.de
2019-07-03 09:32:19 +02:00
Thomas Zimmermann
f5f6f36a49 drm/bochs: Remove PRIME helpers from driver structure
VRAM PRIME helpers are now called through GEM object functions. The
driver callback functions are obsolete.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702115012.4418-3-tzimmermann@suse.de
2019-07-03 09:32:11 +02:00
Thomas Zimmermann
31070a871f drm/vram: Set GEM object functions for PRIME
PRIME functionality is now provided via the callback functions in
struct drm_gem_object_funcs. The driver-structure functions are obsolete.
As a side effect of this patch, VRAM-based drivers get basic PRIME
support automatically without having to set any flags or additional
fields.

v2:
	- use existing PRIME functions for object's table
v3:
	- move object table to EOF so it can refer to internal interfaces

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702115012.4418-2-tzimmermann@suse.de
2019-07-03 09:31:59 +02:00
Greg Kroah-Hartman
b9b667a0c7 FSI changes for 5.3
- Add MAINTAINERS entry. There is now a git tree and a mailing
  list/patchwork for collecting FSI patches
 
  - Bug fix for error driver registration error paths
 
  - Correction for the OCC hwmon driver to meet the spec
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE+nHMAt9PCBDH63wBa3ZZB4FHcJ4FAl0cIIIACgkQa3ZZB4FH
 cJ6z0A//Qy3eu/+s01kq8BAThP77QRyoQP+D7oMoGpr2KxK+82MtFwsuX/vLpcsu
 rYTLn+2xPzY+dWCQx6nWaIij/dkPDWikVarW2+fdMrLhk76XwwkVXPD4J4lUHtVx
 juTWPxLmo7ZAxtwMHyE86hjLR1oTmwZ/arnXYojQ2dka1CZxqpEo7YkRPBLkGjU7
 EcXuCcIGl5ETB9drVsdA8lArLFdgfL/ZFYyEF0epc9KgYrGvJdu1ZdT6bzJkn6C3
 rkCKzQF6fZdszNpo92mjUhkyP3MnnrSVdQPRb/D5wfY9EApfj1YRWS5ikts2lrEf
 tNBat9KJ5nn2AX8FUEKuJazks5ddQk5GOLw6U4vgVayQ0gL8HqofiqybvzKvpX0S
 B0ey0u2d+GeMwiNR+QUNgrnqbbbqy9rLaW8p4zfB70v5qOP8BfWQqnSq+utSqIWZ
 M7xKcial5vQqnBTz0pw+CXVZc0SPD0O7DaK1BmCVOumMAO746eNCPQEwIQVl3Fjt
 FW00qPDWrLnRfdusBWB5mky8b79cnfLht+hLh82gFEeSXpHsRx6rG5luT7moasSK
 EmbXcMM13iVznQk+2IVWWeAXdSDo0yA0eW1SBNBHdrUrdp6jW5pLbDb/F8s+jwQK
 rNYE4IwZYM34L+E/CsFQZw3o5XQy0fsEv6/0tFjjiQPwLeZJZzI=
 =3yOz
 -----END PGP SIGNATURE-----

Merge tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi into char-misc-next

Joel writes:

FSI changes for 5.3

 - Add MAINTAINERS entry. There is now a git tree and a mailing
 list/patchwork for collecting FSI patches

 - Bug fix for error driver registration error paths

 - Correction for the OCC hwmon driver to meet the spec

* tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
  fsi/core: Fix error paths on CFAM init
  OCC: FSI and hwmon: Add sequence numbering
  MAINTAINERS: Add FSI subsystem
2019-07-03 09:21:25 +02:00
Greg Kroah-Hartman
7f61abcdb1 USB-serial updates for 5.3-rc1
Here are the USB-serial updates for 5.3-rc1; just some new device ids
 this time.
 
 All have been in linux-next with no reported issues.
 
 Signed-off-by: Johan Hovold <johan@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXRxL/gAKCRALxc3C7H1l
 CKHnAQDsaOTD7f5Rhn2x0VapiuuxC3BcSHDgizmPcIt2f8F1yQEAgLvMy1//N75O
 XTG6rLe6EsYc/fHj3csdgCURSMZVzQw=
 =wAe3
 -----END PGP SIGNATURE-----

Merge tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for 5.3-rc1

Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.

All have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

* tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: ftdi_sio: add ID for isodebug v1
  USB: serial: option: add support for GosunCn ME3630 RNDIS mode
2019-07-03 09:20:31 +02:00
Thomas Gleixner
7e8e6816c6 stacktrace: Use PF_KTHREAD to check for kernel threads
!current->mm is not a reliable indicator for kernel threads as they might
temporarily use a user mm. Check for PF_KTHREAD instead.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021750100.1802@nanos.tec.linutronix.de
2019-07-03 09:04:06 +02:00
Christoph Hellwig
e0ec0a6ba6 gfs2: remove the unused gfs2_stuffed_write_end function
This function was overlooked when the write_begin and write_end address space
operations were removed as part of gfs2's iomap conversion.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-07-03 08:56:01 +02:00
Christoph Hellwig
f3915f83e8 gfs2: use page_offset in gfs2_page_mkwrite
Without casting page->index to a guaranteed 64-bit type, the value might be
treated as 32-bit on 32-bit platforms and thus get truncated.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-07-03 08:53:01 +02:00
Nishad Kamdar
2200bbec12 powerpc: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style
in the powerpc Hardware Architecture related files.

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Stewart Smith
41732bdc9c powerpc/powernv-eeh: Consisely desribe what this file does
If the previous comment made sense, continue debugging or call your
doctor immediately.

Signed-off-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Krzysztof Kozlowski
14b2f7d908 powerpc/configs: Remove useless UEVENT_HELPER_PATH
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a57 ("driver: base: Disable
   CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
   made default to 'n',
2. It is not recommended (help message: "This should not be used today
   [...] creates a high system load") and was kept only for ancient
   userland,
3. Certain userland specifically requests it to be disabled (systemd
   README: "Legacy hotplug slows down the system and confuses udev").

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Christian Lamparter
3ab3a0689e powerpc/4xx/uic: clear pending interrupt after irq type/pol change
When testing out gpio-keys with a button, a spurious
interrupt (and therefore a key press or release event)
gets triggered as soon as the driver enables the irq
line for the first time.

This patch clears any potential bogus generated interrupt
that was caused by the switching of the associated irq's
type and polarity.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Geert Uytterhoeven
7b570361f6 selftests/powerpc: Add missing newline at end of file
"git diff" says:

    \ No newline at end of file

after modifying the file.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[mpe: Rebase since addition of another test]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Suraj Jitindar Singh
6fbcdd5909 powerpc: Add barrier_nospec to raw_copy_in_user()
Commit ddf35cf376 ("powerpc: Use barrier_nospec in copy_from_user()")
Added barrier_nospec before loading from user-controlled pointers. The
intention was to order the load from the potentially user-controlled
pointer vs a previous branch based on an access_ok() check or similar.

In order to achieve the same result, add a barrier_nospec to the
raw_copy_in_user() function before loading from such a user-controlled
pointer.

Fixes: ddf35cf376 ("powerpc: Use barrier_nospec in copy_from_user()")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Michael Neuling
3fefd1cd95 KVM: PPC: Book3S HV: Fix CR0 setting in TM emulation
When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
    CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
    CR0 <-  0 || MSR[TS] || 0

This fixes the bit shift to put the bits in the correct location.

This is a data integrity issue as CR0 is corrupted.

Fixes: 4bb3c7a020 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:36 +10:00
Alexey Kardashevskiy
5636427d08 powerpc/powernv: Fix stale iommu table base after VFIO
The powernv platform uses @dma_iommu_ops for non-bypass DMA. These ops
need an iommu_table pointer which is stored in
dev->archdata.iommu_table_base. It is initialized during
pcibios_setup_device() which handles boot time devices. However when a
device is taken from the system in order to pass it through, the
default IOMMU table is destroyed but the pointer in a device is not
updated; also when a device is returned back to the system, a new
table pointer is not stored in dev->archdata.iommu_table_base either.
So when a just returned device tries using IOMMU, it crashes on
accessing stale iommu_table or its members.

This calls set_iommu_table_base() when the default window is created.
Note it used to be there before but was wrongly removed (see "fixes").
It did not appear before as these days most devices simply use bypass.

This adds set_iommu_table_base(NULL) when a device is taken from the
system to make it clear that IOMMU DMA cannot be used past that point.

Fixes: c4e9d3c1e6 ("powerpc/powernv/pseries: Rework device adding to IOMMU groups")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Alexey Kardashevskiy
dead1c845d powerpc/pci/of: Parse unassigned resources
The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.

This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.

This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Alexey Kardashevskiy
1a047cc7e5 powerpc/pseries/dma: Enable SWIOTLB
So far the pseries platforms has always been using IOMMU making
SWIOTLB unnecessary. Now we want secure guests which means devices can
only access certain areas of guest physical memory; we are going to
use SWIOTLB for this purpose.

This allows SWIOTLB for pseries. By default there is no change in
behavior.

This enables SWIOTLB when the "swiotlb" kernel parameter is set to
"force".

With the SWIOTLB enabled, the kernel creates a directly mapped DMA
window (using the usual DDW mechanism) and implements SWIOTLB on top
of that.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Alexey Kardashevskiy
efd176a04b powerpc/pseries/dma: Allow SWIOTLB
The commit 8617a5c5bc ("powerpc/dma: handle iommu bypass in
dma_iommu_ops") merged direct DMA ops into the IOMMU DMA ops allowing
SWIOTLB as well but only for mapping; the unmapping and bouncing parts
were left unmodified.

This adds missing direct unmapping calls to .unmap_page() and
.unmap_sg().

This adds missing sync callbacks and directs them to the direct DMA
hooks.

Fixes: 8617a5c5bc ("powerpc/dma: handle iommu bypass in dma_iommu_ops")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Christoph Hellwig
24911acd64 powerpc: remove device_to_mask()
Use the dma_get_mask() helper from dma-mapping.h instead, as they are
functionally identical.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Michael Neuling
a278e7ea60 powerpc: Fix compile issue with force DAWR
If you compile with KVM but without CONFIG_HAVE_HW_BREAKPOINT you fail
at linking with:
  arch/powerpc/kvm/book3s_hv_rmhandlers.o:(.text+0x708): undefined reference to `dawr_force_enable'

This was caused by commit c1fe190c06 ("powerpc: Add force enable of
DAWR on P9 option").

This moves a bunch of code around to fix this. It moves a lot of the
DAWR code in a new file and creates a new CONFIG_PPC_DAWR to enable
compiling it.

Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Minor formatting in set_dawr()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Mathieu Malaterre
548c54acba powerpc: silence a -Wcast-function-type warning in dawr_write_file_bool
In commit c1fe190c06 ("powerpc: Add force enable of DAWR on P9
option") the following piece of code was added:

   smp_call_function((smp_call_func_t)set_dawr, &null_brk, 0);

Since GCC 8 this triggers the following warning about incompatible
function types:

  arch/powerpc/kernel/hw_breakpoint.c:408:21: error: cast between incompatible function types from 'int (*)(struct arch_hw_breakpoint *)' to 'void (*)(void *)' [-Werror=cast-function-type]

Since the warning is there for a reason, and should not be hidden behind
a cast, provide an intermediate callback function to avoid the warning.

Fixes: c1fe190c06 ("powerpc: Add force enable of DAWR on P9 option")
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
6c46fcce39 powerpc/64s/radix: keep kernel ERAT over local process/guest invalidates
ISA v3.0 radix modes provide SLBIA variants which can invalidate ERAT
for effPID!=0 or for effLPID!=0, which allows user and guest
invalidations to retain kernel/host ERAT entries.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
fe7946ce08 powerpc/64s: Rename PPC_INVALIDATE_ERAT to PPC_ISA_3_0_INVALIDATE_ERAT
This makes it clear to the caller that it can only be used on POWER9
and later CPUs.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use "ISA_3_0" rather than "ARCH_300"]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
293c2e27b9 powerpc/64s/exception: simplify hmi control flow
Branch to the relocated 0xc000 address early (still in real mode), to
simplify subsequent branches. Have the virt mode handler avoid just
'windup' and redo the exception from scratch, rather than branching
back to the trampoline.

Rearrange the stack setup instruction location to match the system
reset handler (e.g., right before EXCEPTION_PROLOG_COMMON).

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
f34c9675ca powerpc/64s/exception: hmi remove special case macro
No code change.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
acc8da4492 powerpc/64s/exception: sreset move trampoline ahead of common code
Follow convention and move tramp ahead of common.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:19:35 +10:00
Nicholas Piggin
0e10be2bb9 powerpc/64s/exception: optimise system_reset for idle, clean up non-idle case
The idle wake up code in the system reset interrupt is not very
optimal. There are two requirements: perform idle wake up quickly;
and save everything including CFAR for non-idle interrupts, with
no performance requirement.

The problem with placing the idle test in the middle of the handler
and using the normal handler code to save CFAR, is that it's quite
costly (e.g., mfcfar is serialising, speculative workarounds get
applied, SRR1 has to be reloaded, etc). It also prevents the standard
interrupt handler boilerplate being used.

This pain can be avoided by using a dedicated idle interrupt handler
at the start of the interrupt handler, which restores all registers
back to the way they were in case it was not an idle wake up. CFAR
is preserved without saving it before the non-idle case by making that
the fall-through, and idle is a taken branch.

Performance seems to be in the noise, but possibly around 0.5% faster,
the executed instructions certainly look better. The bigger benefit is
being able to drop in standard interrupt handlers after the idle code,
which helps with subsequent cleanup and consolidation.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup BE by using DOTSYM for idle_return_gpr_loss call]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-07-03 15:18:46 +10:00
Arnaldo Carvalho de Melo
15a108af1a perf script: Allow specifying the files to process guest samples
The 'perf kvm' command set up things so that we can record, report, top,
etc, but not 'script', so make 'perf script' be able to process samples
by allowing to pass guest kallsyms, vmlinux, modules, etc, and if at
least one of those is provided, set perf_guest to true so that guest
samples get properly resolved.

Testing it:

  # perf kvm --guest --guestkallsyms /wb/rhel6.kallsyms --guestmodules /wb/rhel6.modules record -e cycles:Gk
^C[ perf record: Woken up 7 times to write data ]
  [ perf record: Captured and wrote 3.602 MB perf.data.guest (10492 samples) ]

  #
  # perf evlist -i perf.data.guest
cycles:Gk
  # perf evlist -v -i perf.data.guest
cycles:Gk: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|CPU|PERIOD, read_format: ID, disabled: 1, inherit: 1, exclude_user: 1, exclude_hv: 1, mmap: 1, comm: 1, freq: 1, task: 1, sample_id_all: 1, exclude_host: 1, mmap2: 1, comm_exec: 1, ksymbol: 1, bpf_event: 1
  #
  # perf kvm --guestkallsyms /wb/rhel6.kallsyms --guestmodules /wb/rhel6.modules report --stdio -s sym | head -30
  # To display the perf.data header info, please use --header/--header-only options.
  #
  #
  # Total Lost Samples: 0
  #
  # Samples: 10K of event 'cycles:Gk'
  # Event count (approx.): 2434201408
  #
  # Overhead  Symbol
  # ........  ..............................................
  #
      11.93%  [g] avtab_search_node
       3.95%  [g] sidtab_context_to_sid
       2.41%  [g] n_tty_write
       2.20%  [g] _spin_unlock_irqrestore
       1.37%  [g] _aesni_dec4
       1.33%  [g] kmem_cache_alloc
       1.07%  [g] native_write_cr0
       0.99%  [g] kfree
       0.95%  [g] _spin_lock
       0.91%  [g] __memset
       0.87%  [g] schedule
       0.83%  [g] _spin_lock_irqsave
       0.76%  [g] __kmalloc
       0.67%  [g] avc_has_perm_noaudit
       0.66%  [g] kmem_cache_free
       0.65%  [g] glue_xts_crypt_128bit
       0.59%  [g] __d_lookup
       0.59%  [g] __audit_syscall_exit
       0.56%  [g] __memcpy
  #

Then, when trying to use perf script to generate a python script and
then process the events after adding a python hook for non-tracepoint
events:

  # perf script -i perf.data.guest -g python
  generated Python script: perf-script.py
  # vim perf-script.py
  # tail -2 perf-script.py
  def process_event(param_dict):
        print(param_dict["symbol"])
  #
  # perf script -i perf.data.guest -s perf-script.py  | head
  in trace_begin
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  vmx_vmexit
  231
  #

We'd see just the vmx_vmexit, i.e. the samples from the guest don't show
up.

After this patch:

  # perf script --guestkallsyms /wb/rhel6.kallsyms --guestmodules /wb/rhel6.modules -i perf.data.guest -s perf-script.py 2> /dev/null | head -30
  in trace_begin
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  save_args
  do_timer
  drain_array
  inode_permission
  avc_has_perm_noaudit
  run_timer_softirq
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  apic_timer_interrupt
  kvm_guest_apic_eoi_write
  run_posix_cpu_timers
  _spin_lock
  handle_pte_fault
  rcu_irq_enter
  delay_tsc
  delay_tsc
  native_read_tsc
  apic_timer_interrupt
  sys_open
  internal_add_timer
  list_del
  rcu_exit_nohz
  #

Jiri Olsa noticed we need to set 'perf_guest' to true if we want to
process guest samples and I made it be set if one of the guest files
settings get set via the command line options added in this patch, that
match those present in the 'perf kvm' command.

We probably want to have 'perf record', 'perf report' etc to notice that
there are guest samples and do the right thing, which is to look for
files with some suffix that make it be associated with the guest used to
collect the samples, i.e. if a vmlinux file is passed, we can get the
build-id from it, if not some other identifier or simply looking for
"kallsyms.guest", for instance, in the current directory.

Reported-by: Mariano Pache <npache@redhat.com>
Tested-by: Mariano Pache <npache@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Cc: Ali Raza <alirazabhutta.10@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Mario <jmario@redhat.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Orran Krieger <okrieger@redhat.com>
Cc: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Yunlong Song <yunlong.song@huawei.com>
Link: https://lkml.kernel.org/n/tip-d54gj64rerlxcqsrod05biwn@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2019-07-03 00:13:25 -03:00
Bart Van Assche
970d168de6 blk-mq: simplify blk_mq_make_request()
Move the blk_mq_bio_to_request() call in front of the if-statement.

Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-07-02 21:03:38 -06:00
Bart Van Assche
c05f42206f blk-mq: remove blk_mq_put_ctx()
No code that occurs between blk_mq_get_ctx() and blk_mq_put_ctx() depends
on preemption being disabled for its correctness. Since removing the CPU
preemption calls does not measurably affect performance, simplify the
blk-mq code by removing the blk_mq_put_ctx() function and also by not
disabling preemption in blk_mq_get_ctx().

Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-07-02 21:03:27 -06:00
Jeremy Kerr
371975b0b0 fsi/core: Fix error paths on CFAM init
Change d1dcd67825 re-worked the struct fsi_slave initialisation in
fsi_slave_init, but introduced a few inconsitencies: the slave->dev is
now registered through cdev_device_add, but we may kfree() the device
out from underneath the cdev registration. We may also leave an IDA
allocated.

This change fixes the error paths, so that we kfree() only before the
device is registered with the core code. We also move the smode write to
before we start creating proper devices, as it's the most likely to
fail. We also remove the IDA-allocated minor on error, and properly
clean up the of_node.

Fixes: d1dcd67825 ("fsi: Add cfam char devices")
Reported-by: Lei YU <mine260309@gmail.com>
Tested-by: John Wang <wangzqbj@inspur.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
2019-07-03 10:42:53 +09:30
Eddie James
afd26118f0 OCC: FSI and hwmon: Add sequence numbering
Sequence numbering of the commands submitted to the OCC is required by
the OCC interface specification. Add sequence numbering and check for
the correct sequence number on the response.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
2019-07-03 10:41:22 +09:30
Joel Stanley
60c87bc531 MAINTAINERS: Add FSI subsystem
The subsystem was merged some time ago but we did not have a maintainers
entry. The mailing list exists to allow our patchwork to slurp up the
patches. The tree will be co-maintained by myself and Jeremy.

Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
2019-07-03 10:41:22 +09:30
Po-Hsu Lin
ff95bf28c2 selftests/net: skip psock_tpacket test if KALLSYMS was not enabled
The psock_tpacket test will need to access /proc/kallsyms, this would
require the kernel config CONFIG_KALLSYMS to be enabled first.

Apart from adding CONFIG_KALLSYMS to the net/config file here, check the
file existence to determine if we can run this test will be helpful to
avoid a false-positive test result when testing it directly with the
following commad against a kernel that have CONFIG_KALLSYMS disabled:
    make -C tools/testing/selftests TARGETS=net run_tests

Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-02 20:17:49 -04:00
Markus Elfring
590a18e171 PCI: Use seq_puts() instead of seq_printf() in show_device()
The driver name in /proc/bus/pci/devices can be printed without a printf
format specification, so use seq_puts() instead of seq_printf().

This issue was detected by using the Coccinelle software.

Link: https://lore.kernel.org/r/a6b110cb-0d0e-5dc3-9ca1-9041609cf74c@web.de
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2019-07-02 18:38:51 -05:00
Logan Gunthorpe
9c002bb66f PCI/P2PDMA: Fix missing check for dma_virt_ops
Drivers that use dma_virt_ops were meant to be rejected when testing
compatibility for P2PDMA.

This check got inadvertently dropped in one of the later versions of the
original patchset, so add it back.

Fixes: 52916982af ("PCI/P2PDMA: Support peer-to-peer memory")
Link: https://lore.kernel.org/r/20190702173544.21950-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2019-07-02 18:35:15 -05:00
Jaegeuk Kim
cad3836f9e f2fs: allocate blocks for pinned file
This patch allows fallocate to allocate physical blocks for pinned file.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
2019-07-02 15:40:42 -07:00