There is no CLKSEL for timer12 on dra7 unlike for timer1. This
causes issues on booting the device that Tomi noticed if
DEBUG_SLAB is enabled and the clkctrl clock does not properly
handle non-existing clock. Let's drop the bogus CLKSEL clock,
the clkctrl clock handling gets fixed separately.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: 4ed0dfe3cf ("ARM: dts: dra7: Move l4 child devices to probe them with ti-sysc")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not allocate memory for the Get PHY Abilities command data buffer when
it is not necessary, change one local variable to another to reduce the
number of de-references, reduce the scope of some local variables, and
reorder the code and change exit points to get rid of an unnecessary goto
label.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_cfg_vsi_lan returns a value of type enum ice_status. So
use a local of the same type to capture the return value.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds driver support for Forward Error Correction (FEC)
and ethtool handlers to set/get FEC params.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for virtchnl_vector_map.[rxq|txq]_map to use bitmap to
associate indicated queues with the specified vector. This support is
needed since the Windows AVF driver calls VIRTCHNL_OP_CONFIG_IRQ_MAP for
each vector and used the bitmap to indicate the associated queues.
Updated ice_vc_dis_qs_msg to not subtract one from
virtchnl_irq_map_info.num_vectors, and changed the VSI vector index to
the vector id. This change supports the Windows AVF driver which maps
one vector at a time and sets num_vectors to one. Using vectors_id to
index the vector array .
Add check for vector_id zero, and return VIRTCHNL_STATUS_ERR_PARAM
if vector_id is zero and there are rings associated with that vector.
Vector_id zero is for the OICR.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate adding unicast and broadcast MAC filters in a single new
function ice_init_mac_fltr.
Move ice_napi_del to ice_lib.c
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_free_vf_res() we are writing to the VFINT_DYN_CTLN
register in the PF's function space to disable all VF's interrupts. This
is incorrect because this register is only for use in the VF's function
space. This becomes obvious when seeing that the valid indices used for
the VFINT_DYN_CTLN register is from 0-63, which is the maximum number of
interrupts for a VF (not including the OICR interrupt). Fix this by
writing to the GLINT_DYN_CTL register for each VF. We can do this
because we keep track of each VF's first_vector_idx inside of the PF's
function space and the number of interrupts given to each VF.
Also in ice_free_vfs() we were disabling Rx/Tx queues after calling
pci_disable_sriov(). One part of disabling the Tx queues causes the PF
driver to trigger a software interrupt, which causes the VF's napi
routine to run. This doesn't currently work because pci_disable_sriov()
causes iavf_remove() to be called which disables interrupts. Fix this by
disabling Rx/Tx queues prior to pci_disable_sriov().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's found while review and probably never happens, but real number
of queues is set per device, and error path should be per device.
So split error path based on usage_count.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei says:
====================
Decoupling PHYLINK from struct net_device
Following two separate discussion threads in:
https://www.spinics.net/lists/netdev/msg569087.html
and:
https://www.spinics.net/lists/netdev/msg570450.html
Previous RFC patch set: https://www.spinics.net/lists/netdev/msg571995.html
PHYLINK was reworked in order to accept multiple operation types,
PHYLINK_NETDEV and PHYLINK_DEV, passed through a phylink_config
structure alongside the corresponding struct device.
One of the main concerns expressed in the RFC was that using notifiers
to signal the corresponding phylink_mac_ops would break PHYLINK's API
unity and that it would become harder to grep for its users.
Using the current approach, we maintain a common API for all users.
Also, printing useful information in PHYLINK, when decoupled from a
net_device, is achieved using dev_err&co on the struct device received
(in DSA's case is the device corresponding to the dsa_switch).
PHYLIB (which PHYLINK uses) was reworked to the extent that it does not
crash when connecting to a PHY and the net_device pointer is NULL.
Lastly, DSA has been reworked in its way that it handles PHYs for ports
that lack a net_device (CPU and DSA ports). For these, it was
previously using PHYLIB and is now using the PHYLINK_DEV operation type.
Previously, a driver that wanted to support PHY operations on CPU/DSA
ports has to implement .adjust_link(). This patch set not only gives
drivers the options to use PHYLINK uniformly but also urges them to
convert to it. For compatibility, the old code is kept but it will be
removed once all drivers switch over.
The patchset was tested on the NXP LS1021A-TSN board having the
following Ethernet layout:
https://lkml.org/lkml/2019/5/5/279
The CPU port was moved from the internal RGMII fixed-link (enet2 ->
switch port 4) to an external loopback Cat5 cable between the enet1 port
and the front-facing swp2 SJA1105 port. In this mode, both the master
and the CPU port have an attached PHY which detects link change events:
[ 49.105426] fsl-gianfar soc:ethernet@2d50000 eth1: Link is Down
[ 50.305486] sja1105 spi0.1: Link is Down
[ 53.265596] fsl-gianfar soc:ethernet@2d50000 eth1: Link is Up - 1Gbps/Full - flow control off
[ 54.466304] sja1105 spi0.1: Link is Up - 1Gbps/Full - flow control off
Changes in v2:
- fixed sparse warnings
- updated 'Documentation/ABI/testing/sysfs-class-net-phydev'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLIB and PHYLINK handle fixed-link interfaces differently. PHYLIB
wraps them in a software PHY ("pseudo fixed link") phydev construct such
that .adjust_link driver callbacks see an unified API. Whereas PHYLINK
simply creates a phylink_link_state structure and passes it to
.mac_config.
At the time the driver was introduced, DSA was using PHYLIB for the
CPU/cascade ports (the ones with no net devices) and PHYLINK for
everything else.
As explained below:
commit aab9c4067d
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Thu May 10 13:17:36 2018 -0700
net: dsa: Plug in PHYLINK support
Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2)
will need to implement phylink_mac_ops from now on to preserve
functionality, since PHYLINK *does not* create a phy_device instance
for fixed links.
In the above patch, DSA guards the .phylink_mac_config callback against
a NULL phydev pointer. Therefore, .adjust_link is not called in case of
a fixed-link user port.
This patch fixes the situation by converting the driver from using
.adjust_link to .phylink_mac_config. This can be done now in a unified
fashion for both slave and CPU/cascade ports because DSA now uses
PHYLINK for all ports.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.
The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it. The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.
For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest addition to the PHYLINK infrastructure, we are faced
with a decision on when to print necessary info using the struct
net_device and when with the struct device.
Add a series of macros that encapsulate this decision and replace all
uses of netdev_err&co with phylink_err.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PHYLINK_DEV operation type, the PHYLINK infrastructure can work
without an attached net_device. For printing usecases, instead, a struct
device * should be passed to PHYLINK using the phylink_config structure.
Also, netif_carrier_* calls ar guarded by the presence of a valid
net_device. When using the PHYLINK_DEV operation type, we cannot check
link status using the netif_carrier_ok() API so instead, keep an
internal state of the MAC and call mac_link_{down,up} only when the link
changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that reduces the clutter in phylink_resolve
around calling the .mac_link_up/.mac_link_down driver callbacks. In a
further patch this logic will be extended to emit notifications in case
a net device does not exist.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.
Changes are needed in the following areas:
- Printing: In some places netdev_err was replaced with phydev_err.
- Incrementing reference count to the parent MDIO bus driver: If there
is no net device, then the reference count should definitely be
incremented since there is no chance that it was an Ethernet driver
who registered the MDIO bus.
- Sysfs links are not created in case there is no attached_dev.
- No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.
This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on the GBit versions supports 1000/Full only, however the PHY
partially claims to support 1000/Half. So let's explicitly remove
this mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload of matchall classifier and police action are now
supported via the tc command.
Supported police parameters are: rate and burst.
Example:
Add:
tc qdisc add dev eth3 handle ffff: ingress
tc filter add dev eth3 parent ffff: prio 1 handle 2 \
matchall skip_sw \
action police rate 100Mbit burst 10000
Show:
tc -s -d qdisc show dev eth3
tc -s -d filter show dev eth3 ingress
Delete:
tc filter del dev eth3 parent ffff: prio 1
tc qdisc del dev eth3 handle ffff: ingress
Signed-off-by: Joergen Andreasen <joergen.andreasen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sprgs are a set of 4 general purpose sprs provided for software use.
SPRG3 is special in that it can also be read from userspace. Thus it is
used on linux to store the cpu and numa id of the process to speed up
syscall access to this information.
This register is overwritten with the guest value on kvm guest entry,
and so needs to be restored on exit again. Thus restore the value on
the guest exit path in kvmhv_p9_guest_entry().
Cc: stable@vger.kernel.org # v4.20+
Fixes: 95a6432ce9 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Under XIVE, the ESB pages of an interrupt are used for interrupt
management (EOI) and triggering. They are made available to guests
through a mapping of the XIVE KVM device.
When a device is passed-through, the passthru_irq helpers,
kvmppc_xive_set_mapped() and kvmppc_xive_clr_mapped(), clear the ESB
pages of the guest IRQ number being mapped and let the VM fault
handler repopulate with the correct page.
The ESB pages are mapped at offset 4 (KVM_XIVE_ESB_PAGE_OFFSET) in the
KVM device mapping. Unfortunately, this offset was not taken into
account when clearing the pages. This lead to issues with the
passthrough devices for which the interrupts were not functional under
some guest configuration (tg3 and single CPU) or in any configuration
(e1000e adapter).
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
According to Documentation/virtual/kvm/locking.txt, the srcu read lock
should be taken when accessing the memslots of the VM. The XIVE KVM
device needs to do so when configuring the page of the OS event queue
of vCPU for a given priority and when marking the same page dirty
before migration.
This avoids warnings such as :
[ 208.224882] =============================
[ 208.224884] WARNING: suspicious RCU usage
[ 208.224889] 5.2.0-rc2-xive+ #47 Not tainted
[ 208.224890] -----------------------------
[ 208.224894] ../include/linux/kvm_host.h:633 suspicious rcu_dereference_check() usage!
[ 208.224896]
other info that might help us debug this:
[ 208.224898]
rcu_scheduler_active = 2, debug_locks = 1
[ 208.224901] no locks held by qemu-system-ppc/3923.
[ 208.224902]
stack backtrace:
[ 208.224907] CPU: 64 PID: 3923 Comm: qemu-system-ppc Kdump: loaded Not tainted 5.2.0-rc2-xive+ #47
[ 208.224909] Call Trace:
[ 208.224918] [c000200cdd98fa30] [c000000000be1934] dump_stack+0xe8/0x164 (unreliable)
[ 208.224924] [c000200cdd98fa80] [c0000000001aec80] lockdep_rcu_suspicious+0x110/0x180
[ 208.224935] [c000200cdd98fb00] [c0080000075933a0] gfn_to_memslot+0x1c8/0x200 [kvm]
[ 208.224943] [c000200cdd98fb40] [c008000007599600] gfn_to_pfn+0x28/0x60 [kvm]
[ 208.224951] [c000200cdd98fb70] [c008000007599658] gfn_to_page+0x20/0x40 [kvm]
[ 208.224959] [c000200cdd98fb90] [c0080000075b495c] kvmppc_xive_native_set_attr+0x8b4/0x1480 [kvm]
[ 208.224967] [c000200cdd98fca0] [c00800000759261c] kvm_device_ioctl_attr+0x64/0xb0 [kvm]
[ 208.224974] [c000200cdd98fcf0] [c008000007592730] kvm_device_ioctl+0xc8/0x110 [kvm]
[ 208.224979] [c000200cdd98fd10] [c000000000433a24] do_vfs_ioctl+0xd4/0xcd0
[ 208.224981] [c000200cdd98fdb0] [c000000000434724] ksys_ioctl+0x104/0x120
[ 208.224984] [c000200cdd98fe00] [c000000000434768] sys_ioctl+0x28/0x80
[ 208.224988] [c000200cdd98fe20] [c00000000000b888] system_call+0x5c/0x70
legoater@boss01:~$
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Fixes: e6714bd167 ("KVM: PPC: Book3S HV: XIVE: Add a control to dirty the XIVE EQ pages")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The XICS-on-XIVE KVM device needs to allocate XIVE event queues when a
priority is used by the OS. This is referred as EQ provisioning and it
is done under the hood when :
1. a CPU is hot-plugged in the VM
2. the "set-xive" is called at VM startup
3. sources are restored at VM restore
The kvm->lock mutex is used to protect the different XIVE structures
being modified but in some contexts, kvm->lock is taken under the
vcpu->mutex which is not permitted by the KVM locking rules.
Introduce a new mutex 'lock' for the KVM devices for them to
synchronize accesses to the XIVE device structures.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fix the length value of VEB_DI_IECP.
Fixes: be1da7070a ("drm/i915/gvt: vGPU command scanner")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Gao, Fred <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The vgpu ggtt range should be in vgpu aperture or hidden range. This
patch enforce begin and end address check and guarantee both of them are
in the valid range.
For size=0, it will regress to vgpu_gmadr_is_valid(), will refine
this usage in a later fix.
Fixes: 2707e44466 ("drm/i915/gvt: vGPU graphics memory virtualization")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Enter failsafe if vgpu tries to change CSFE_CHICKEN1_REG setting
which is controlled by host.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Enter failsafe if vgpu tries to change GFX_MODE controlled by host.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Host prints below warning message when guest running some application:
"gvt: vgpu(1) Invalid FORCE_NONPRIV write 2754 at 24f0".
"gvt: vgpu(1) Invalid FORCE_NONPRIV write 28a0 at 24f0".
Registers 0x2754 and 0x28a0 are required by guest so add to whitelist.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Show the '^' character when a policy rule has flag IMA_INMASK.
Fixes: 80eae209d6 ("IMA: allow reading back the current IMA policy")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
This patch prevents memory access beyond the evm_tfm array by checking the
validity of the index (hash algorithm) passed to init_desc(). The hash
algorithm can be arbitrarily set if the security.ima xattr type is not
EVM_XATTR_HMAC.
Fixes: 5feeb61183 ("evm: Allow non-SHA1 digital signatures")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Add the shared cx/mx and sensor sub-system's cx and mx
power-domains found on MSM8998.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add RPM power domain bindings for the msm8998 family of SoC
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the shared cx/mx and the low-power-island's cx and mx power-domains
found on QCS404.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Fixup corner/vfc with vlfl/vfl]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add RPM power domain bindings for the qcs404 family of SoC
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibis: Add supported rpmpd states for qcs404]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
QCS404 uses individual resource type magic for each power-domain, so
adjust the macros slightly to make them reusable for this.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibi: Extend rpmpd corner pair to a generic rpmpd pair]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
rpmpd max state varies across SoCs and SoC families, add support
in the driver to make it SoC/SoC family specific
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Remoteproc q6v5-mss calls set_performance_state with INT_MAX on
rpmpd. This is currently ignored since it is greater than the
max supported state. Fixup rpmpd state to max if the required
state is greater than all the supported states.
Fixes: 075d3db8d1 ("soc: qcom: rpmpd: Add support for get/set performance state")
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Commit e31f941cf9 ("MAINTAINERS: update list of qcom drivers") had a
typo in the filename, replace the underscore with dash.
Fixes: e31f941cf9 ("MAINTAINERS: update list of qcom drivers")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the rpmpd node on the msm8998 and define the available levels.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: dropped use of level defines, to allow merging in parallel]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the rpmpd node on the qcs404 and define the available levels.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sibis: fixup available levels]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: dropped use of level defines, to allow merging in parallel]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>