The err_rst_reqb, ext_clki, lowpwr, and ref_clko pin groups are present,
but no pinmux functions refer to them, hence they can not be selected.
Fixes: 1e7d5d849c ("sh-pfc: Add emev2 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Current Switchtec's BAR setup registers are limited to 32bits,
corresponding to the maximum MW (memory window) size is <4G.
Increase the MW sizes with the addition of the BAR Setup Extension
Register for the upper 32bits of a 64bits MW size. This increases the MW
range to between 4K and 2^63.
Reported-by: Boris Glimcher <boris.glimcher@emc.com>
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The number of available NT req id mapping table entries per NTB control
register is 512. The driver mistakenly limits the number to 256.
Fix the array size of NT req id mapping table.
Fixes: c082b04c9d ("NTB: switchtec: Add NTB hardware register definitions")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec NTB crosslink BARs are 64bit addressed but they are printed as
32bit addressed BARs. Fix debug log to increment the BAR numbers by 2 to
reflect the 64bit address alignment.
Fixes: 0175250182 ("ntb_hw_switchtec: Add initialization code for crosslink")
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When facility.76 MSAX3 is present for the guest we must issue a validity
interception if the CRYCBD is not valid.
The bit CRYCBD.31 is an effective field and tested at each guest level
and has for effect to mask the facility.76
It follows that if CRYCBD.31 is clear and AP is not in use we do not
have to test the CRYCBD validatity even if facility.76 is present in the
host.
Fixes: 6ee7409820 ("KVM: s390: vsie: allow CRYCB FORMAT-0")
Cc: stable@vger.kernel.org
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1549876849-32680-1-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix markup warning: insert a blank line before the hint.
Documentation/driver-api/dmaengine/dmatest.rst:63: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Thomas noticed that the new arch/x86/include/asm/cpu_device_id.h header is
a train-wreck that didn't incorporate review feedback like not using __u8
in kernel-only headers.
While at it also fix all the *other* problems this header has:
- Use canonical names for the header guards. It's inexplicable why a non-standard
guard was used.
- Don't define the header guard to 1. Plus annotate the closing #endif as done
absolutely every other header. Again, an inexplicable source of noise.
- Move the kernel API calls provided by this header next to each other, there's
absolutely no reason to have them spread apart in the header.
- Align the INTEL_CPU_DESC() macro initializations vertically, this is easier to
read and it's also the canonical style.
- Actually name the macro arguments properly: instead of 'mod, step, rev',
spell out 'model, stepping, revision' - it's not like we have a lack of
characters in this header.
- Actually make arguments macro-safe - again it's inexplicable why it wasn't
done properly to begin with.
Quite amazing how many problems a 41 lines header can contain.
This kind of code quality is unacceptable, and it slipped through the
review net of 2 developers and 2 maintainers, including myself, until
Thomas noticed it. :-/
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Starting from opregion version 2.1 (roughly corresponding to ICL+) the
RVDA field is relative from the beginning of opregion, not absolute
address.
Fix the error path while at it.
v2: Make relative vs. absolute conditional on the opregion version,
bumped for the purpose. Turned out there are machines relying on
absolute RVDA in the wild.
v3: Fix the version checks
Fixes: 04ebaadb9f ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-2-jani.nikula@intel.com
The u32 version field encodes major, minor, revision and reserved. We've
basically been checking for any non-zero version.
Add opregion version logging while at it.
v2: Fix the fix of the version check
Fixes: 04ebaadb9f ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-1-jani.nikula@intel.com
If we allocate while iterating the rbtree of active nodes, we may hit
the shrinker and so retire the i915_active, reaping the rbtree. Modifying
the rbtree as we iterate is not good behaviour, so acquire the
i915_active first to keep the tree intact whenever we allocate.
Fixes: a42375af0a ("drm/i915: Release the active tracker tree upon idling")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208134704.23039-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The "Domain 0 is reserved, so dont process it" comment suggests that a NULL
pointer corresponds to domain 0. I don't think that's true, and in any
case, every caller supplies a non-NULL domain pointer that has already been
dereferenced, so the test is unnecessary.
Remove the test for a null "domain" pointer. No functional change
intended.
This null pointer check was added by 5e98c4b1d6 ("Allocation and free
functions of virtual machine domain").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
domain_remove_dev_info() takes a struct dmar_domain * argument, but doesn't
use it. Remove it. No functional change intended.
The last use of this argument was removed by 127c761598 ("iommu/vt-d:
Pass device_domain_info to __dmar_remove_one_dev_info").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A local variable initialization is a hint that the variable will be used in
an unusual way. If the initialization is unnecessary, that hint becomes a
distraction.
Remove unnecessary initializations. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use dev_printk() when possible so the IOMMU messages are more consistent
with other messages related to the device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use dev_printk() when possible so the IOMMU messages are more consistent
with other messages related to the device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use dev_printk() when possible so the IOMMU messages are more consistent
with other messages related to the device.
E.g., I think these messages related to surprise hotplug:
pciehp 0000:80:10.0:pcie004: Slot(36): Link Down
iommu: Removing device 0000:87:00.0 from group 12
pciehp 0000:80:10.0:pcie004: Slot(36): Card present
pcieport 0000:80:10.0: Data Link Layer Link Active not set in 1000 msec
would be easier to read as these (also requires some PCI changes not
included here):
pci 0000:80:10.0: Slot(36): Link Down
pci 0000:87:00.0: Removing from iommu group 12
pci 0000:80:10.0: Slot(36): Card present
pci 0000:80:10.0: Data Link Layer Link Active not set in 1000 msec
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The etnaviv_gem_prime_get_sg_table() is supposed to return error
pointers. Otherwise it can lead to a NULL dereference when it's called
from drm_gem_map_dma_buf().
Fixes: 5f4a4a73f4 ("drm/etnaviv: fix gem_prime_get_sg_table to return new SG table")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Keep the page at address 0 as faulting to catch any potential state
setup issues early.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Vince (and later on Ravi) reported crashes in the BTS code during
fuzzing with the following backtrace:
general protection fault: 0000 [#1] SMP PTI
...
RIP: 0010:perf_prepare_sample+0x8f/0x510
...
Call Trace:
<IRQ>
? intel_pmu_drain_bts_buffer+0x194/0x230
intel_pmu_drain_bts_buffer+0x160/0x230
? tick_nohz_irq_exit+0x31/0x40
? smp_call_function_single_interrupt+0x48/0xe0
? call_function_single_interrupt+0xf/0x20
? call_function_single_interrupt+0xa/0x20
? x86_schedule_events+0x1a0/0x2f0
? x86_pmu_commit_txn+0xb4/0x100
? find_busiest_group+0x47/0x5d0
? perf_event_set_state.part.42+0x12/0x50
? perf_mux_hrtimer_restart+0x40/0xb0
intel_pmu_disable_event+0xae/0x100
? intel_pmu_disable_event+0xae/0x100
x86_pmu_stop+0x7a/0xb0
x86_pmu_del+0x57/0x120
event_sched_out.isra.101+0x83/0x180
group_sched_out.part.103+0x57/0xe0
ctx_sched_out+0x188/0x240
ctx_resched+0xa8/0xd0
__perf_event_enable+0x193/0x1e0
event_function+0x8e/0xc0
remote_function+0x41/0x50
flush_smp_call_function_queue+0x68/0x100
generic_smp_call_function_single_interrupt+0x13/0x30
smp_call_function_single_interrupt+0x3e/0xe0
call_function_single_interrupt+0xf/0x20
</IRQ>
The reason is that while event init code does several checks
for BTS events and prevents several unwanted config bits for
BTS event (like precise_ip), the PERF_EVENT_IOC_PERIOD allows
to create BTS event without those checks being done.
Following sequence will cause the crash:
If we create an 'almost' BTS event with precise_ip and callchains,
and it into a BTS event it will crash the perf_prepare_sample()
function because precise_ip events are expected to come
in with callchain data initialized, but that's not the
case for intel_pmu_drain_bts_buffer() caller.
Adding a check_period callback to be called before the period
is changed via PERF_EVENT_IOC_PERIOD. It will deny the change
if the event would become BTS. Plus adding also the limit_period
check as well.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20190204123532.GA4794@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enable various options in the defconfigs of both i386 and x86_64
that could do with some test coverage in automated testing. Note
that these options are typically enabled by distros as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable futex_pi_state.refcount is used as pure
reference counter. Convert it to refcount_t and fix up
the operations.
**Important note for maintainers:
Some functions from refcount_t API defined in lib/refcount.c
have different memory ordering guarantees than their atomic
counterparts. Please check Documentation/core-api/refcount-vs-atomic.rst
for more information.
Normally the differences should not matter since refcount_t provides
enough guarantees to satisfy the refcounting use cases, but in
some rare cases it might matter.
Please double check that you don't have some undocumented
memory guarantees for this variable usage.
For the futex_pi_state.refcount it might make a difference
in following places:
- get_pi_state() and exit_pi_state_list(): increment in
refcount_inc_not_zero() only guarantees control dependency
on success vs. fully ordered atomic counterpart
- put_pi_state(): decrement in refcount_dec_and_test() provides
RELEASE ordering and ACQUIRE ordering on success
vs. fully ordered atomic counterpart
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: dvhart@infradead.org
Link: http://lkml.kernel.org/r/1549369467-3505-1-git-send-email-elena.reshetova@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move io-pgtable.h to include/linux/ and export alloc_io_pgtable_ops
and free_io_pgtable_ops. This enables drivers outside drivers/iommu/ to
use the page table library. Specifically, some ARM Mali GPUs use the
ARM page table formats.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add James to the list of reviewers of the firmware-assisted RAS glue.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lkml.kernel.org/r/20190205083836.21641-1-bp@alien8.de
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the GHES notification type is SDEI, register the provided event
using the SDEI-GHES helper.
SDEI may be one of two types of event, normal and critical. Critical
events can interrupt normal events, so these must have separate
fixmap slots and locks in case both event types are in use.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
APEI's Generic Hardware Error Source structures do not describe
whether the SDEI event is shared or private, as this information is
discoverable via the API.
GHES needs to know whether an event is normal or critical to avoid
sharing locks or fixmap entries, but GHES shouldn't have to know about
the SDEI API.
Add a helper to register the GHES using the appropriate normal or
critical callback.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With drmP.h removed from drm_modeset_helper.h the build of
komeda filed as reported by linux-next
Add missing include files to fix build.
For the files touched group include files and sort them.
The fix was tested on a tree with drm-misc-next merged.
And the patch was also tested to work without drm-misc-next merged.
Build tested on arm + x86.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> [linux-next]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Wang <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208221324.27002-1-sam@ravnborg.org
My @samusung.com address is going to cease existing soon, so change it to
an address which can actually be used to contact me.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:
[ 36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[ 36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[ 36.950666] Call trace:
[ 36.950670] queued_spin_lock_slowpath+0x1cc/0x2c8
[ 36.950681] _raw_spin_lock_irqsave+0x64/0x78
[ 36.950692] complete+0x28/0x70
[ 36.950703] ffs_epfile_io_complete+0x3c/0x50
[ 36.950713] usb_gadget_giveback_request+0x34/0x108
[ 36.950721] dwc3_gadget_giveback+0x50/0x68
[ 36.950723] dwc3_thread_interrupt+0x358/0x1488
[ 36.950731] irq_thread_fn+0x30/0x88
[ 36.950734] irq_thread+0x114/0x1b0
[ 36.950739] kthread+0x104/0x130
[ 36.950747] ret_from_fork+0x10/0x1c
I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065
Where the completion done is setup on the stack:
DECLARE_COMPLETION_ONSTACK(done);
Then later we setup a request and queue it, and wait for it:
if (unlikely(wait_for_completion_interruptible(&done))) {
/*
* To avoid race condition with ffs_epfile_io_complete,
* dequeue the request first then check
* status. usb_ep_dequeue API should guarantee no race
* condition with req->complete callback.
*/
usb_ep_dequeue(ep->ep, req);
interrupted = ep->status < 0;
}
The problem is, that we end up being interrupted, dequeue the
request, and exit.
But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.
Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:
wait_for_completion(&done);
Is needed right after the usb_ep_dequeue().
Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.
This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bde ("usb: dwc3: gadget:
remove wait_end_transfer").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to allow this code to be re-used, remove the dependency
on the rest of the cros_ec code from the cros_ec_lpc_mec functions.
Instead of using a hardcoded register base address of 0x800 have
this be passed in to cros_ec_lpc_mec_init(). The existing cros_ec
use case now passes in the 0x800 base address this way.
There are some error checks that happen in cros_ec_lpc_mec_in_range()
that probably shouldn't be there, as they are checking kernel-space
callers and not user-space input. However, we'll just do the refactor in
this patch, and in a future patch might remove this error checking and
fix all the instances of code that calls this.
There's a similar problem in cros_ec_lpc_read_bytes(), where we return a
checksum, but on error just return 0. This should probably be changed so
that it returns int, but we don't want to have to mess with all the
calling code for this fix. Maybe we'll come back through later and fix
this.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Nick Crews <ncrews@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Some of the things included in driver's TODO file have
been properly achieved. Update file accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename following parameters of function dot11d_update_country to fix
checkpatch warning: Avoid CamelCase and make the parameter names more
readable, understandable.
pTaddr -> address
CoutryIeLen -> country_len
pCoutryIe -> country
Signed-off-by: Himadri Pandya <himadri18.07@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename following local variables of function dot11d_update_country to
fix checkpatch warning: Avoid CamelCase and make the variable names more
readable, understandable.
NumTriples -> number_of_triples
MaxChnlNum -> max_channel_number
pTriple -> triple
Signed-off-by: Himadri Pandya <himadri18.07@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_pci_is_blacklisted() is very similar to pci_match_id() implementation.
Replace it with the latter.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the RTC block on the 32-bit Amlogic Meson6, Meson8,
Meson8b and Meson8m2 SoCs.
The RTC is split in to two parts, which are both managed by this driver:
- the AHB front end
- and a simple serial connection to the actual registers
The RTC_COUNTER register which holds the time is 32-bits wide.
There are four 32-bit wide (in total: 16 bytes) "regmem" registers which
are exposed using nvmem. On Amlogic's 3.10 kernel this is used to store
data which needs to survive a suspend / resume cycle.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[resurrected Ben's patches after 2 years]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 32-bit Amlogic Meson SoCs (Meson6, Meson8, Meson8b and Meson8m2)
have a built-in RTC block.
It has the following inputs:
- an 32.768kHz crystal oscillator
- an interrupt line
- a reset line
- 0.9V voltage input
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[resurrected patches from Ben after 2 years]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the oscillator of the rtc gets interrupted,
e.g. due to an empty battery, reading from the rtc will now return an error
and the oscillator bit will be cleared, once the rtc is successfully reset.
Signed-off-by: Oliver Rohe <oliver.rohe@wago.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the original code before 181bf1e815 the loop was continuing until
it finds the first matching superios[i].io and p->base.
But after 181bf1e815 the logic changed and the loop now returns the
pointer to the first mismatched array element which is then used in
get_superio_dma() and get_superio_irq() and thus returning the wrong
value.
Fix the condition so that it now returns the correct pointer.
Fixes: 181bf1e815 ("parport_pc: clean up the modified while loops using for")
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: QiaoChong <qiaochong@loongson.cn>
[rewrite the commit message]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Add new extcon-ptn5150.c extcon provider driver
- NXP PTN5150 supports the detection of USB connectors through
USB Type-C port and controls it. It is interfaced to the host
controller using an I2C interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xaa1
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 5.1
Detailed description for this pull request:
1. Add new extcon-ptn5150.c extcon provider driver
- NXP PTN5150 supports the detection of USB connectors through
USB Type-C port and controls it. It is interfaced to the host
controller using an I2C interface.
* tag 'extcon-next-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon:
extcon: ptn5150: Fix return value check in ptn5150_i2c_probe()
extcon: Add support for ptn5150 extcon driver
Make sure the CRC and tag checksum of the Logical Volume Integrity
Descriptor are valid before the structure is written out to disk.
Otherwise, unless the filesystem is unmounted gracefully, the on-disk
LVID will be invalid - which is unnecessary filesystem damage.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Jan Kara <jack@suse.cz>