The Allwinner H6 SoC uses a v2.12a DesignWare HDMI controller, with
dedicated CEC and HDCP clocks added; the PHY connected is a standard
DesignWare HDMI PHY.
Add binding for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[added HDCP clock and reset]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-19-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
It turns out that even new DW HDMI controllers exhibits same magenta
line issues as older versions.
Enable workaround for v2.12a.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-15-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Randconfig testing revealed a very old bug, with gcc-8:
sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw':
sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (fw == NULL) {
^
sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here
const struct firmware *fw;
We must check the return code of request_firmware() before we look at the
pointer result that may be uninitialized when the function fails.
Fixes: 9012c9544e ("ASoC: Intel: mrfld - Add DSP load and management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc notices that without either the ac97 bus or the pdata, we never
initialize the regmap pointer, which leads to an uninitialized variable
access:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:666:2: error: 'regmap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since that configuration is invalid, it's better to return an error
here. I tried to avoid adding complexity to the conditions, and turned
the #ifdef into a regular if(IS_ENABLED()) check for readability.
This in turn requires moving some header file declarations out of
an #ifdef.
The same code is used in three drivers, all of which I'm changing
the same way.
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_ops structure can be const as it is only stored in the
ops field of a snd_soc_dai_link structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the comparison of div < 0 is always false because div is
an unsigned int. Fix this by making div an int.
Detected by CoverityScan, CID#1475309 ("Unsigned compared against 0")
Fixes: 8307b2afd3 "(ASoC: stm32: sai: set sai as mclk clock provider")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SUN50I_CODEC_ANALOG selects SND_SUNXI_ADDA_PR_REGMAP which is leftover
of renaming SND_SUNXI_ADDA_PR_REGMAP to SND_SUN8I_ADDA_PR_REGMAP. Replace
it with SND_SUN8I_ADDA_PR_REGMAP to fix possible link errors for some
configurations:
sound/soc/sunxi/sun50i-codec-analog.o: In function `sun50i_codec_analog_probe':
sun50i-codec-analog.c:(.text+0x62): undefined reference to `sun8i_adda_pr_regmap_init'
Fixes: 42371f327d ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value from devm_memremap() is not checked correctly.
The test is done against a wrong variable. This patch fix it.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ar->target_version is same for QCA99x0, QCA4019, QCA9888
and QCA9984, this ended up in assigning the wrong hw_mem_layouts.
This patch adds additional hw_rev check to assign correct
hw_mem_layouts.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
QCA9984 firmware 10.4-3.5.3-00057
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA4019.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WCN3990 firmware becomes unavailable,
the host driver receives a FW down indication, post
which all the direct hardware register access should
be avoided, in order to prevent improper behavior in
the host driver.
Set the crash_flush flag when the host driver receives
a FW_DOWN_IND via qmi, in order to stop the untimely
hardware register access. Also handle the case, where
we need to do core register only for the first FW_READY
indication, which is when we initialize the host driver.
All the subsequent FW_READY indication will be received
in subsystem recovery case and we only need to do the
restart work. The state of driver is maintained using
flags to distinguish between first and subsequent FW_READY
indication received.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As I'll no longer be working with Arm, add a mailmap entry so any mail
directed towards me reaches the appropriate mailbox.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Use the generic DMA API instead of the legacy PCI DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace legacy callbacks with ->select_chip() and ->exec_op().
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace use of legacy .IOADDR_R/W with runtime calculations based on
priv->io_base.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each controller driver having access to NAND R/B pin over GPIO would
have to reimplement the polling loop otherwise.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Check return value of nand_read_data_op.
Notice that, currently, all instances of nand_read_data_op() are
being checked, with the exception of two of them in marvell_nand
driver, in which the caller function explicitly returns 0 every
time.
Also, notice that I moved the declaration of *ret* to the top of
fsmc_read_page_hwecc().
Addresses-Coverity-ID: 1471968 ("Unchecked return value")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
W25N01GV is a single die version of the already supported
W25M02GV with half the capacity. Everything else is the
same so introduce support for W25N01GV.
Datasheet:http://www.winbond.com/resource-files/w25n01gv%20revl%20050918%20unsecured.pdf
Tested on 8devices Jalapeno dev board under OpenWrt running 4.19-rc5.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Recently, the minimum required version of binutils was changed to
2.20, which supports POPCNT instruction mnemonics.
Replace the byte-wise specification of POPCNT with those proper
mnemonics.
[ bp: massage commit message and remove line breaks. ]
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181014202354.21281-1-ubizjak@gmail.com
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
This commit adds compatibles used in H6 display pipeline, namely for
display engine, mixer and TV TCON.
H6 display engine is somewhat similar to R40, just less TCONs and
mixer support more features.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-8-jernej.skrabec@siol.net
Support for mixer0, mixer1, writeback and rotation units is added.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds necessary description and dt includes for H6 DE3 clock.
It is very similar to others, but memory region has some additional
registers not found in DE2.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Video PLL factors can be set in a way that final PLL rate is outside
stable range. H6 user manual specifically says that N factor should not
be below 12. While it doesn't says anything about maximum stable rate, it
is clear that PLL doesn't work at 6.096 GHz (254 * 24 MHz).
Set minimum allowed PLL video rate to 288 MHz (12 * 24 MHz) and maximum
to 2.4 GHz, which is maximum in BSP driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has multiplier N range between 1 and 254. Since parent
rate is 24MHz, intermediate result when calculating final rate easily
overflows 32 bit variable.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
Fixes: ee28648cb2 ("clk: sunxi-ng: Remove the use of rational computations")
CC: <stable@vger.kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently MP clocks don't consider adjusting parent rate even if they
are allowed to do so. Such behaviour considerably lowers amount of
possible rates, which is very inconvenient when such clock is used for
pixel clock, for example.
In order to improve the situation, adjusting parent rate is considered
when allowed.
This code is inspired by clk_divider_bestdiv() function, which does
basically the same thing for different clock type.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 DE3 bus is similar to the A64 DE2 one.
Add its compatible string with the A64 string as fallback to the
binding.
Some description of the binding is modified to make it more generic.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed compatible name]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-2-jernej.skrabec@siol.net
The Mapleboard MP130 is a single board computer based on the Allwinner
H3 SoC, with all schematics freely available. The Lite version includes
1GB main memory and 8GB eMMC.
https://www.mapleboard.org/en (still mostly in Chinese even when English
is selected)
This DTS is based upon the DTS shipped with the board which uses
mapleboard,mp130- prefixes instead of the allwinner,sun8i variants.
v2: Fold in review comments from Maxime Ripard
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board has an Ethernet port, which is connected to a
RTL8211E PHY, then the PHY is connected to the MAC on H6 SoC.
Add support for the Ethernet port.
The PHY needs some time to start up, and the time is modelled as enable
ramp delay of the regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has an EMAC like the one in A64.
Add device tree nodes for the H6 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC features a Ethernet MAC that is similar to the one
in A64.
Add a compatible string for it with A64 fallback compatible string, in
this case the A64 driver can be used.
The "internal" PHY is not internal from the perspective of the H6 main
die, instead it's on the co-packaged AC200 chip, and connected to the
main die with RMII at the in-package Port A PIO bank. So from the SoC
driver side it needs no special treatment.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
QoS nodes keep information about priorites etc on the interconnect
and loose state when the power-domain gets disabled. Therefore the
power-domain driver stores the settings of available qos nodes and
restores them when the power-domain gets enabled again.
So add the qos nodes found on the Cortex-A9 socs from Rockchip, so
that they can then be connected to the power-domains.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MUX bits for MMC clock register range are 25:24 where 24 is shift
and 2 is width So fix the width number from 3 to 2.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the compatible values for the power-domain controllers found on
rk3066 and rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>