The GIC irqchips can now use a HW resend when a retrigger is invoked by
check_irq_resend(). However, should the HW resend fail, check_irq_resend()
will still attempt to trigger a SW resend, which is still a bad idea for
the GICs.
Prevent this from happening by setting IRQD_HANDLE_ENFORCE_IRQCTX on all
GIC IRQs. Technically per-cpu IRQs do not need this, as their flow handlers
never set IRQS_PENDING, but this aligns all IRQs wrt context enforcement:
this also forces all GIC IRQ handling to happen in IRQ context (as defined
by in_irq()).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-3-valentin.schneider@arm.com
It is pretty easy to provide a retrigger callback for the ITS,
as it we already have the required support in terms of
irq_set_irqchip_state().
Note that this only works for device-generated LPIs, and not
the GICv4 doorbells, which should never have to be retriggered
anyway.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
While digging around IRQCHIP_EOI_IF_HANDLED and irq/resend.c, it has come
to my attention that the IRQ resend situation seems a bit precarious for
the GIC(s).
When marking an IRQ with IRQS_PENDING, handle_fasteoi_irq() will bail out
and issue an irq_eoi(). Should the IRQ in question be re-enabled,
check_irq_resend() will trigger a SW resend, which will go through the flow
handler again and issue *another* irq_eoi() on the *same* IRQ
activation. This is something the GIC spec clearly describes as a bad idea:
any EOI must match a previous ACK.
Implement irq_chip.irq_retrigger() for the GIC chips by setting the GIC
pending bit of the relevant IRQ. After being called by check_irq_resend(),
this will eventually trigger a *new* interrupt which we will handle as usual.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200730170321.31228-2-valentin.schneider@arm.com
On resending an interrupt, we only check the outermost irqchip for
a irq_retrigger callback. However, this callback could be implemented
at an inner level. Use irq_chip_retrigger_hierarchy() in this case.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
BLOCK_PRIV is never used after it was introduced.
So better to remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCX1Rn1wAKCRCAXGG7T9hj
vlEjAQC/KGC3wYw5TweWcY48xVzgvued3JLAQ6pcDlOe6osd6AEAzZcZKgL948cx
oY0T98dxb/U+lUhbIzhpBr/30g8JbAQ=
=Xcxp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"A small series for fixing a problem with Xen PVH guests when running
as backends (e.g. as dom0).
Mapping other guests' memory is now working via ZONE_DEVICE, thus not
requiring to abuse the memory hotplug functionality for that purpose"
* tag 'for-linus-5.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: add helpers to allocate unpopulated memory
memremap: rename MEMORY_DEVICE_DEVDAX to MEMORY_DEVICE_GENERIC
xen/balloon: add header guard
The SATA PHY in Exynos5250 SoCs has two interfaces and two device nodes:
1. sata-phy@12170000
2. i2c-9/i2c@38
The first node represents the actual SATA PHY device with phy-cells.
The second represents an additional I2C interface, needed by the driver
to communicate with the SATA PHY device. It is not a PHY-provider in
the terms of dtschema so rename it to silence dtbs_check warning:
arch/arm/boot/dts/exynos5250-arndale.dt.yaml: sata-phy@38: '#phy-cells' is a required property
From schema: lib/python3.6/site-packages/dtschema/schemas/phy/phy-provider.yaml
This second device node is also a property of SoC, not a board so move
it there.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902155733.20271-2-krzk@kernel.org
The property samsung,i2c-slave-addr in I2C9 controller on Exynos5250
Arndale and SMDK5250 boards, is not actually needed. There is only one
master on this bus. It's not clear why this property was added at first
place.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200902155733.20271-1-krzk@kernel.org
The purpose of those assigned-clock-* properties is to configure clock for
for the I2S device so move them to respective node.
This suppresses the dtbs_check warning:
arch/arm/boot/dts/exynos5422-odroidxu3.dt.yaml: sound: 'clocks' is a dependency of 'assigned-clocks'
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Hartmut Knaack was an active reviewer and contributor to the IIO
subsystem and drivers. However his last message on LKML is from
October 2015.
In thanks for Hartmut's effort, move him name to the Credits.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio <linux-iio@vger.kernel.org>
Link: https://lore.kernel.org/r/20200903181926.5606-2-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Emails to Beniamin Bia bounce with no such address so remove him from
maintainers. After this removal, many entries for Analog Devices Inc
IIO drivers look exactly the same so consolidate them.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio <linux-iio@vger.kernel.org>
Link: https://lore.kernel.org/r/20200903181926.5606-1-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few changes to how I write this cover letter.
* Started to use manufacturer prefixes to group changes better.
* Stop list minor formatting etc changes.
* Whilst I appreciate those changes, we don't need to call them out here.
New device support:
* adi,adxrs290
- New driver for this gyroscope with dt bindings. One fix follows.
* ams,as73211
- New driver for this colour sensor with dt bindings. Also includes
docs for XYZ modifiers as used for the CIE colour space. Sysfs docs.
* atlas,atlas-ezo-sensor
- Support O_2 sensor, includes new modifier for concentration.
- Support humidity sensor.
* ti,hdc2010
- New driver support hdc2010 and hdc2080 humidity sensors. Includes dt
bindings.
Cleanup, minor fixes and features
* core
- Make the trigger related stub functions static inline, avoiding some build
warnings.
- buffer-dmaengine. Allow adjusting bytes_used with residue info.
* dev_error_probe to replace open coded equivalent in many drivers.
* docs and comment fixes
- Fix some typos, doubled words, capitalisation and punctuation.
* dt binding conversions to yaml
- lltc,ltc2497
- lltc,ltc2632
- maxim,max11100
- maxim,max1118
- maxim,max9611
- microchip,mcp3201
- microchip,mcp342x (add to trivial devices)
- ti,adc0832
- ti,adc108s102
- ti,adc128s052
- ti,adc161s626
- ti,ads8344
- ti,tlc4541 (includes adding an accidentally dropped original binding doc)
* adi,adi-axi-adc
- Use kobj_to_dev instead of open coding.
* adi,ad5686
- Constify iio_chan_spec
* adi,ad8366
- Add HMC1119 to kconfig help text as the driver supports it.
* adi,ad9523
- Use devm for reset of probe and drop remove.
* adi,adxl372
- Tidy up alignment
- Add OF table
- Add peak mode support with some docs.
* bosch,bma220 (general tidy up)
- Fix some return codes.
- Use read_avail callback rather than open coding attrs.
- Use dev_get_drvdata rather than dance via to_spi_device()
- Mark PM functions as __maybe_unused rather than #ifdef fun.
- Drop ACPI_PTR protections and ifdefs.
- Tidy up header ordering.
- BIT and GENMASK
* broadcom,bcm_iproc
- Drop of_match_ptr protection and switch to mod_devicetable.h
Part of general move to get this anti-pattern out of IIO.
* melexis,mlx90614
- Simplify some calculations.
- Add some kernel_doc
- Use regmap poll loop rather than open coding.
- Add extended calibration option.
* sensortec,sx9310, wide ranging set of fixes and cleanups.
- Document dt-binding.
- Rename some macros to align better with spec sheet
- Fix some issues with irq handling.
- Drop of_match_ptr and ACPI_PTR macros to avoid unused warnings etc.
- Switch to probe_new
- Fix memory alignment for iio_push_to_buffers_with_timestamp()
- Use long for bitmaps to allow use of for_each_bit_set()
- Use regmap_read_poll instead of opencoding.
- Simplify error paths
- Enabled regulators at probe.
- Use trigger flags from firmware rather than forcing them in the driver.
* ti,adc081c
- Drop ACPI IDs that are not likely to be official ones and we don't believe
anyone is using.
* ti,adc108s102
- Drop CONFIG_OF and of_match_ptr protections.
* ti,adc128s052
- Drop of_match_ptr protection and include mod_devicetable.h
* ti,dac5571
- Support powerdown for mutlichannel usecases.
* xpowers,axp20x
- Convert from OF to generic fw / device properties. Unlikely anyone will
use this with anything other than devicetree, but this is part of a
general move across IIO.
-----BEGIN PGP SIGNATURE-----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=7Vzn
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.10a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanup for IIO in 5.10 cycle, take 2
A few changes to how I write this cover letter.
* Started to use manufacturer prefixes to group changes better.
* Stop list minor formatting etc changes.
* Whilst I appreciate those changes, we don't need to call them out here.
New device support:
* adi,adxrs290
- New driver for this gyroscope with dt bindings. One fix follows.
* ams,as73211
- New driver for this colour sensor with dt bindings. Also includes
docs for XYZ modifiers as used for the CIE colour space. Sysfs docs.
* atlas,atlas-ezo-sensor
- Support O_2 sensor, includes new modifier for concentration.
- Support humidity sensor.
* ti,hdc2010
- New driver support hdc2010 and hdc2080 humidity sensors. Includes dt
bindings.
Cleanup, minor fixes and features
* core
- Make the trigger related stub functions static inline, avoiding some build
warnings.
- buffer-dmaengine. Allow adjusting bytes_used with residue info.
* dev_error_probe to replace open coded equivalent in many drivers.
* docs and comment fixes
- Fix some typos, doubled words, capitalisation and punctuation.
* dt binding conversions to yaml
- lltc,ltc2497
- lltc,ltc2632
- maxim,max11100
- maxim,max1118
- maxim,max9611
- microchip,mcp3201
- microchip,mcp342x (add to trivial devices)
- ti,adc0832
- ti,adc108s102
- ti,adc128s052
- ti,adc161s626
- ti,ads8344
- ti,tlc4541 (includes adding an accidentally dropped original binding doc)
* adi,adi-axi-adc
- Use kobj_to_dev instead of open coding.
* adi,ad5686
- Constify iio_chan_spec
* adi,ad8366
- Add HMC1119 to kconfig help text as the driver supports it.
* adi,ad9523
- Use devm for reset of probe and drop remove.
* adi,adxl372
- Tidy up alignment
- Add OF table
- Add peak mode support with some docs.
* bosch,bma220 (general tidy up)
- Fix some return codes.
- Use read_avail callback rather than open coding attrs.
- Use dev_get_drvdata rather than dance via to_spi_device()
- Mark PM functions as __maybe_unused rather than #ifdef fun.
- Drop ACPI_PTR protections and ifdefs.
- Tidy up header ordering.
- BIT and GENMASK
* broadcom,bcm_iproc
- Drop of_match_ptr protection and switch to mod_devicetable.h
Part of general move to get this anti-pattern out of IIO.
* melexis,mlx90614
- Simplify some calculations.
- Add some kernel_doc
- Use regmap poll loop rather than open coding.
- Add extended calibration option.
* sensortec,sx9310, wide ranging set of fixes and cleanups.
- Document dt-binding.
- Rename some macros to align better with spec sheet
- Fix some issues with irq handling.
- Drop of_match_ptr and ACPI_PTR macros to avoid unused warnings etc.
- Switch to probe_new
- Fix memory alignment for iio_push_to_buffers_with_timestamp()
- Use long for bitmaps to allow use of for_each_bit_set()
- Use regmap_read_poll instead of opencoding.
- Simplify error paths
- Enabled regulators at probe.
- Use trigger flags from firmware rather than forcing them in the driver.
* ti,adc081c
- Drop ACPI IDs that are not likely to be official ones and we don't believe
anyone is using.
* ti,adc108s102
- Drop CONFIG_OF and of_match_ptr protections.
* ti,adc128s052
- Drop of_match_ptr protection and include mod_devicetable.h
* ti,dac5571
- Support powerdown for mutlichannel usecases.
* xpowers,axp20x
- Convert from OF to generic fw / device properties. Unlikely anyone will
use this with anything other than devicetree, but this is part of a
general move across IIO.
* tag 'iio-for-5.10a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (96 commits)
drivers/iio/humidity/hdc2010.c:305:2-3: Unneeded semicolon
iio: accel: bma220: Remove unneeded blank lines
iio: accel: bma220: Use BIT() and GENMASK() macros
iio: accel: bma220: Group IIO headers together
iio: accel: bma220: Drop ACPI_PTR() and accompanying ifdeffery
iio: accel: bma220: Mark PM functions as __maybe_unused
iio: accel: bma220: Use dev_get_drvdata() directly
iio: accel: bma220: Convert to use ->read_avail()
iio: accel: bma220: Fix returned codes from bma220_init(), bma220_deinit()
dt-bindings: iio: adc: microchip,mcp3201 yaml conversion.
iio: buffer-dmaengine: adjust `bytes_used` with residue info
dt-bindings: iio: adc: ti,tlc4541 binding conversion
dt-bindings: iio: adc: tlc4541 - recover accidentally dropped binding doc
dt-bindings: iio: adc: ti,ads8344 yaml conversion
dt-bindings: iio: adc: ti,adc128s052 yaml conversion.
dt-bindings: iio: adc: ti,adc0832 yaml conversion.
dt-bindings: iio: adc: ti,adc161s626 yaml conversion.
dt-bindings: iio: adc: lltc,ltc2497 yaml conversion.
dt-bindings: iio: adc: ti,adc108s102 yaml conversion
dt-bindings: trivial-devices: Add mcp342x ADCs and drop separate binding doc.
...
On one board I found that:
probe of 5-0028 returned 1 after 259547 usecs
While some of this time is attributable to the pile of i2c transfers
that we do at probe time, the lion's share (over 200 ms) is sitting
waiting in the polling loop in sx9310_init_compensation() waiting for
the hardware to indicate that it's done.
There's no reason to block probe of all other devices on our probe.
Turn on async probe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Daniel Campello <campello@chromium.org>
Link: https://lore.kernel.org/r/20200901081920.v2.1.Id02b2f451b3eed71ddd580f4b8b44b3e33e84970@changeid
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There seems no reason to allow for compile-testing on ARM only, so
remove this restriction.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200904170416.16061-1-alex.dewar90@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that the PWM drivers which we use have been converted to the atomic
PWM API, we can move the i915 panel code over to using the atomic PWM API.
The removes a long standing FIXME and this removes a flicker where
the backlight brightness would jump to 100% when i915 loads even if
using the fastset path.
Note that this commit also simplifies pwm_disable_backlight(), by dropping
the intel_panel_actually_set_backlight(..., 0) call. This call sets the
PWM to 0% duty-cycle. I believe that this call was only present as a
workaround for a bug in the pwm-crc.c driver where it failed to clear the
PWM_OUTPUT_ENABLE bit. This is fixed by an earlier patch in this series.
After the dropping of this workaround, the usleep call, which seems
unnecessary to begin with, has no useful effect anymore, so drop that too.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-18-hdegoede@redhat.com
So far for devices using an external PWM controller (devices using
pwm_setup_backlight()), we have been hardcoding the minimum allowed
PWM level to 0. But several of these devices specify a non 0 minimum
setting in their VBT.
Change pwm_setup_backlight() to use get_backlight_min_vbt() to get
the minimum level.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-17-hdegoede@redhat.com
So far for devices using an external PWM controller (devices using
pwm_setup_backlight()), we have been hardcoding the period-time passed to
pwm_config() to 21333 ns.
I suspect this was done because many VBTs set the PWM frequency to 200
which corresponds to a period-time of 5000000 ns, which greatly exceeds
the PWM_MAX_PERIOD_NS define in the Crystal Cove PMIC PWM driver, which
used to be 21333.
This PWM_MAX_PERIOD_NS define was actually based on a bug in the PWM
driver where its period and duty-cycle times where off by a factor of 256.
Due to this bug the hardcoded CRC_PMIC_PWM_PERIOD_NS value of 21333 would
result in the PWM driver using its divider of 128, which would result in
a PWM output frequency of 6000000 Hz / 256 / 128 = 183 Hz. So actually
pretty close to the default VBT value of 200 Hz.
Now that this bug in the pwm-crc driver is fixed, we can actually use
the VBT defined frequency.
This is important because:
a) With the pwm-crc driver fixed it will now translate the hardcoded
CRC_PMIC_PWM_PERIOD_NS value of 21333 ns / 46 Khz to a PWM output
frequency of 23 KHz (the max it can do).
b) The pwm-lpss driver used on many models has always honored the
21333 ns / 46 Khz request
Some panels do not like such high output frequencies. E.g. on a Terra
Pad 1061 tablet, using the LPSS PWM controller, the backlight would go
from off to max, when changing the sysfs backlight brightness value from
90-100%, anything under aprox. 90% would turn the backlight fully off.
Honoring the VBT specified PWM frequency will also hopefully fix the
various bug reports which we have received about users perceiving the
backlight to flicker after a suspend/resume cycle.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-16-hdegoede@redhat.com
Factor the code which checks and drm_dbg_kms-s the VBT PWM frequency
out of get_backlight_max_vbt().
This is a preparation patch for honering the VBT PWM frequency for
devices which use an external PWM controller (devices using
pwm_setup_backlight()).
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-15-hdegoede@redhat.com
Implement the pwm_ops.get_state() method to complete the support for the
new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-14-hdegoede@redhat.com
Replace the enable, disable and config pwm_ops with an apply op,
to support the new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-13-hdegoede@redhat.com
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
So far we've kept the PWM_OUTPUT_ENABLE bit set when disabling the PWM,
this commit makes crc_pwm_disable() clear it on disable and makes
crc_pwm_enable() set it again on re-enable.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-12-hdegoede@redhat.com
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
The BACKLIGHT_EN register at address 0x51 really controls a separate
output-only GPIO which is earmarked to be used as output connected to the
backlight-enable pin for LCD panels, this GPO is part of the PMIC's
"Display Panel Control Block." . This pin should probably be moved over
to a GPIO provider driver (and consumers modified accordingly), but that
is something for an(other) patch.
Enabling / disabling the actual PWM output is controlled by the
PWM_OUTPUT_ENABLE bit of the PWM0_CLK_DIV register.
As the comment in the old code already indicates we must disable the PWM
before we can change the clock divider. But the crc_pwm_disable() and
crc_pwm_enable() calls the old code make for this only change the
BACKLIGHT_EN register; and the value of that register does not matter for
changing the period / the divider. What does matter is that the
PWM_OUTPUT_ENABLE bit must be cleared before a new value can be written.
This commit modifies crc_pwm_config() to clear PWM_OUTPUT_ENABLE instead
when changing the period, so that period changes actually work.
Note this fix will cause a significant behavior change on some devices
using the CRC PWM output to drive their backlight. Before the PWM would
always run with the output frequency configured by the BIOS at boot, now
the period time specified by the i915 driver will actually be honored.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-11-hdegoede@redhat.com
The CRC PWM controller has a clock-divider which divides the clock with
a value between 1-128. But as can seen from the PWM_DIV_CLK_xxx
defines, this range maps to a register value of 0-127.
So after calculating the clock-divider we must subtract 1 to get the
register value, unless the requested frequency was so high that the
calculation has already resulted in a (rounded) divider value of 0.
Note that before this fix, setting a period of PWM_MAX_PERIOD_NS which
corresponds to the max. divider value of 128 could have resulted in a
bug where the code would use 128 as divider-register value which would
have resulted in an actual divider value of 0 (and the enable bit being
set). A rounding error stopped this bug from actually happen. This
same rounding error means that after the subtraction of 1 it is impossible
to set the divider to 128. Also bump PWM_MAX_PERIOD_NS by 1 ns to allow
setting a divider of 128 (register-value 127).
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-10-hdegoede@redhat.com
While looking into adding atomic-pwm support to the pwm-crc driver I
noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and
there is a clock-divider which divides this with a value between 1-128,
and there are 256 duty-cycle steps.
The pwm-crc code before this commit assumed that a clock-divider
setting of 1 means that the PWM output is running at 6 MHZ, if that
is true, where do these 256 duty-cycle steps come from?
This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that
seems unlikely for a PMIC which is using a silicon process optimized for
power-switching transistors. It is way more likely that there is an 8
bit counter for the duty cycle which acts as an extra fixed divider
wrt the PWM output frequency.
The main user of the pwm-crc driver is the i915 GPU driver which uses it
for backlight control. Lets compare the PWM register values set by the
video-BIOS (the GOP), assuming the extra fixed divider is present versus
the PWM frequency specified in the Video-BIOS-Tables:
Device: PWM Hz set by BIOS PWM Hz specified in VBT
Asus T100TA 200 200
Asus T100HA 200 200
Lenovo Miix 2 8 23437 20000
Toshiba WT8-A 23437 20000
So as we can see if we assume the extra division by 256 then the register
values set by the GOP are an exact match for the VBT values, where as
otherwise the values would be of by a factor of 256.
This commit fixes the period / duty_cycle calculations to take the
extra division by 256 into account.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-9-hdegoede@redhat.com
PWM controller drivers should not restore the PWM state on resume. The
convention is that PWM consumers do this by calling pwm_apply_state(),
so that it can be done at the exact moment when the consumer needs
the state to be stored, avoiding e.g. backlight flickering.
The only in kernel consumers of the pwm-lpss code, the i915 driver
and the pwm-class sysfs interface code both correctly restore the
state on resume, so there is no need to do this in the pwm-lpss code.
More-over the removed resume handler is buggy, since it blindly
restores the ctrl-register contents without setting the update
bit, which is necessary to get the controller to actually use/apply
the restored base-unit and on-time-div values.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-8-hdegoede@redhat.com
Before this commit pwm_lpss_apply() was assuming 2 pre-conditions
were met by the existing hardware state:
1. That the base-unit and on-time-div read back from the
control register are those actually in use, so that it
can skip setting the update bit if the read-back value
matches the desired values.
2. That the controller is enabled when the cached
pwm_state.enabled says that the controller is enabled.
As the long history of fixes for subtle (often suspend/resume)
lpss-pwm issues shows, these assumptions are not necessary
always true.
1. Specifically is not true on some (*) Cherry Trail devices
with a nasty GFX0._PS3 method which: a. saves the ctrl reg value.
b. sets the base-unit to 0 and writes the update bit to apply/commit
c. restores the original ctrl value without setting the update bit,
so that the 0 base-unit value is still in use.
2. Assumption 2. currently is true, but only because of the code which
saves/restores the state on suspend/resume. By convention restoring the
PWM state should be done by the PWM consumer and the presence of this
code in the pmw-lpss driver is a bug. Therefor the save/restore code will
be dropped in the next patch in this series, after which this assumption
also is no longer true.
This commit changes the pwm_lpss_apply() to not make any assumptions about
the state the hardware is in. Instead it makes pwm_lpss_apply() always
fully program the PWM controller, making it much less fragile.
*) Seen on the Acer One 10 S1003, Lenovo Ideapad Miix 310 and 320 models
and various Medion models.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-7-hdegoede@redhat.com
In the not-enabled -> enabled path pwm_lpss_apply() needs to get a
runtime-pm reference; and then on any errors it needs to release it
again.
This leads to somewhat hard to read code. This commit introduces a new
pwm_lpss_prepare_enable() helper and moves all the steps necessary for
the not-enabled -> enabled transition there, so that we can error check
the entire transition in a single place and only have one pm_runtime_put()
on failure call site.
While working on this I noticed that the enabled -> enabled (update
settings) path was quite similar, so I've added an enable parameter to
the new pwm_lpss_prepare_enable() helper, which allows using it in that
path too.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-6-hdegoede@redhat.com
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e504 ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e504 ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e504 ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets turned off from the _PS3 method of the graphics-card dev:
Method (_PS3, 0, Serialized) // _PS3: Power State 3
{
...
PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
PSAT |= 0x03
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
...
}
Where PSAT is the power-status register of the PWM controller.
Since the i915 driver will do a pwm_get on the pwm device as it uses it to
control the LCD panel backlight, there is a device-link marking the i915
device as a consumer of the pwm device. So that the PWM controller will
always be suspended after the i915 driver suspends (which is the right
thing to do). This causes the above GFX0 PS3 AML code to run before
acpi_lpss.c calls acpi_lpss_save_ctx().
So on these devices the PWM controller will already be off when
acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff)
as ctx register values.
When these bogus values get restored on resume the PWM controller actually
keeps working, since most bits are reserved, but this does set bit 3 of
the LPSS General purpose register, which for the PWM controller has the
following function: "This bit is re-used to support 32kHz slow mode.
Default is 19.2MHz as PWM source clock".
This causes the clock of the PWM controller to switch from 19.2MHz to
32KHz, which is a slow-down of a factor 600. Surprisingly enough so far
there have been few bug reports about this. This is likely because the
i915 driver was hardcoding the PWM frequency to 46 KHz, which divided
by 600 would result in a PWM frequency of approx. 78 Hz, which mostly
still works fine. There are some bug reports about the LCD backlight
flickering after suspend/resume which are likely caused by this issue.
But with the upcoming patch-series to finally switch the i915 drivers
code for external PWM controllers to use the atomic API and to honor
the PWM frequency specified in the video BIOS (VBT), this becomes a much
bigger problem. On most cases the VBT specifies either 200 Hz or 20
KHz as PWM frequency, which with the mentioned issue ends up being either
1/3 Hz, where the backlight actually visible blinks on and off every 3s,
or in 33 Hz and horrible flickering of the backlight.
There are a number of possible solutions to this problem:
1. Make acpi_lpss_save_ctx() run before GFX0._PS3
Pro: Clean solution from pov of not medling with save/restore ctx code
Con: As mentioned the current ordering is the right thing to do
Con: Requires assymmetry in at what suspend/resume phase we do the save vs
restore, requiring more suspend/resume ordering hacks in already
convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
Pro: Reasonably clean
Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
Pro: Not PWM specific, might help with issues on other LPSS devices too
Con: If we can get away with not restoring the ctx why bother with it at
all?
4. Do not save the ctx for CHT PWM controllers
Pro: Clean, as simple as dropping a flag?
Con: Not so simple as dropping a flag, needs a new flag to ensure that
we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
Pro: Keeps acpi_lpss.c code clean
Con: Moves knowledge of LPSS-context into the pwm-lpss.c code
1 and 5 both do not seem to be a desirable way forward.
3 and 4 seem ok, but they both assume that restoring the LPSS-context
registers is not necessary. I have done a couple of test and those do
show that restoring the LPSS-context indeed does not seem to be necessary
on devices using s2idle suspend (and successfully reaching S0i3). But I
have no hardware to test deep / S3 suspend. So I'm not sure that not
restoring the context is safe.
That leaves solution 2, which is about as simple / clean as 3 and 4,
so this commit fixes the described problem by implementing a new
LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-3-hdegoede@redhat.com
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets poked from the _PS0 method of the graphics-card device:
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
If (((Local0 & 0x03) == 0x03))
{
PSAT &= 0xFFFFFFFC
Local1 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
RSTA = Zero
RSTF = Zero
RSTA = One
RSTF = One
PWMB |= 0xC0000000
PWMC = PWMB /* \_SB_.PCI0.GFX0.PWMB */
}
Where PSAT is the power-status register of the PWM controller, so if it
is in D3 when the GFX0 device's PS0 method runs then it will turn it on
and restore the PWM ctrl register value it saved from its PS3 handler.
Note not only does it restore it, it ors it with 0xC0000000 turning it
on at a time where we may not want it to get turned on at all.
The pwm_get call which the i915 driver does to get a reference to the
PWM controller, already adds a device-link making the GFX0 device a
consumer of the PWM device. So it should already have been resumed when
the above AML runs and the AML should thus not do its undesirable poking
of the PWM controller register.
But the PCI core powers on PCI devices in the no-irq resume phase and
thus calls the troublesome PS0 method in the no-irq resume phase.
Where as LPSS devices by default are resumed in the early resume phase.
This commit sets the resume_from_noirq flag in the bsw_pwm_dev_desc
struct, so that Cherry Trail PWM controllers will be resumed in the
no-irq phase. Together with the device-link added by the pwm-get this
ensures that the PWM controller will be on when the troublesome PS0
method runs, which stops it from poking the PWM controller.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-2-hdegoede@redhat.com
Mediatek HDMI phy driver is moved from drivers/gpu/drm/mediatek to
drivers/phy/mediatek, so add the new folder to the Mediatek DRM drivers'
information.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
mtk_hdmi_phy is currently placed inside mediatek drm driver, but it's
more suitable to place a phy driver into phy driver folder, so move
mtk_hdmi_phy driver into phy driver folder.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
mtk_hdmi_phy is a part of mtk_hdmi module, but phy driver should be an
independent module rather than be part of drm module, so separate the phy
driver to an independent module.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
tz_disabled is used to control mtk_hdmi output signal, but this variable
is stored in mtk_hdmi_phy and mtk_hdmi_phy does not use it. So move
tz_disabled to mtk_hdmi where it's used.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
DIGITAL_NFC_DEP_REQ_RES_TAILROOM is never used after it was introduced.
DIGITAL_NFC_DEP_REQ_RES_HEADROOM is no more used after below
commit e8e7f42175 ("NFC: digital: Remove useless call to skb_reserve()")
Remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove SRVL_CTRL_PKT_SIZE which is defined more than once.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the correct offset to clear the stale filter hit
bytes counter. Otherwise, the counter starts incrementing
from the stale information, instead of 0.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luo bin says:
====================
hinic: BugFixes
The bugs fixed in this patchset have been present since the following
commits:
patch #1: Fixes: 00e57a6d4a ("net-next/hinic: Add Tx operation")
patch #2: Fixes: 5e126e7c4e ("hinic: add firmware update support")
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware erases the entire flash region which may take several
seconds before flashing, so we bump up the timeout to ensure this
cmd won't return failure.
Fixes: 5e126e7c4e ("hinic: add firmware update support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We free memory regardless of the return value of SET_FUNC_STATE
cmd in hinic_close function to avoid memory leak and this cmd may
timeout when fw is busy with handling other cmds, so we bump up the
timeout of this cmd to ensure it won't return failure.
Fixes: 00e57a6d4a ("net-next/hinic: Add Tx operation")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While looking for ->files in ->defer_list, consider that requests there
may actually be links.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While trying to cancel requests with ->files, it also should look for
requests in ->defer_list, otherwise it might end up hanging a thread.
Cancel all requests in ->defer_list up to the last request there with
matching ->files, that's needed to follow drain ordering semantics.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
-----BEGIN PGP SIGNATURE-----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=w1IL
-----END PGP SIGNATURE-----
mergetag object 4e4bb89446
type commit
tag clang-format-for-linus-v5.9-rc4
tagger Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> 1599306139 +0200
The usual trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
-----BEGIN PGP SIGNATURE-----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=Lcl0
-----END PGP SIGNATURE-----
mergetag object e5fc436f06
type commit
tag compiler-attributes-for-linus-v5.9-rc4
tagger Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> 1599306822 +0200
Two trivial changes and a fix for sparse:
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting __has_attribute (Luc Van Oostenryck)
-----BEGIN PGP SIGNATURE-----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=RrSY
-----END PGP SIGNATURE-----
Merge tags 'auxdisplay-for-linus-v5.9-rc4', 'clang-format-for-linus-v5.9-rc4' and 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux
Pull misc fixes from Miguel Ojeda:
"A trivial patch for auxdisplay:
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
The usual clang-format trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
And Luc requested me to pick a sparse fix on my queue, so here it goes
along with other two trivial Compiler Attributes ones (also from Luc).
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van
Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van
Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting
__has_attribute (Luc Van Oostenryck)"
* tag 'auxdisplay-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
auxdisplay: Replace HTTP links with HTTPS ones
* tag 'clang-format-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
clang-format: Update with the latest for_each macro list
* tag 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
sparse: use static inline for __chk_{user,io}_ptr()
Compiler Attributes: fix comment concerning GCC 4.6
Compiler Attributes: remove comment about sparse not supporting __has_attribute
- HSDK-4xd Dev system: perf driver updates for sampling interrupt
- HSDK* Dev System : Ethernet broken [Evgeniy Didin]
- HIGHMEM broken (2 memory banks) [Mike Rapoport]
- show_regs() rewrite once and for all
- Other minor fixes
-----BEGIN PGP SIGNATURE-----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=vOZp
-----END PGP SIGNATURE-----
Merge tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- HSDK-4xd Dev system: perf driver updates for sampling interrupt
- HSDK* Dev System: Ethernet broken [Evgeniy Didin]
- HIGHMEM broken (2 memory banks) [Mike Rapoport]
- show_regs() rewrite once and for all
- Other minor fixes
* tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id
arc: fix memory initialization for systems with two memory banks
irqchip/eznps: Fix build error for !ARC700 builds
ARC: show_regs: fix r12 printing and simplify
ARC: HSDK: wireup perf irq
ARC: perf: don't bail setup if pct irq missing in device-tree
ARC: pgalloc.h: delete a duplicated word + other fixes
Commit 0da4c3d393 ("net: phy: add Lynx PCS module") added the files in
./drivers/net/pcs/, but the new LYNX PCS MODULE section refers to
./drivers/net/phy/.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:
warning: no file matches F: drivers/net/phy/pcs-lynx.c
Repair the LYNX PCS MODULE section by referring to the right location.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge misc fixes from Andrew Morton:
"19 patches.
Subsystems affected by this patch series: MAINTAINERS, ipc, fork,
checkpatch, lib, and mm (memcg, slub, pagemap, madvise, migration,
hugetlb)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
mm: memcg: fix memcg reclaim soft lockup
memcg: fix use-after-free in uncharge_batch
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Ensure MDIO diversion is used
Changes in v2:
- export of_update_property() to permit building bcm_sf2 as a module
- provided a better explanation of the problem being solved after
explaining it to Andrew during the v1 review
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
