Registering our slave MDIO bus outside of the OF infrastructure is
necessary in order to avoid creating double references of the same
Device Tree nodes, however it is not sufficient to guarantee that the
MDIO bus diversion is used because of_phy_connect() will still resolve
to a valid PHY phandle and it will connect to the PHY using its parent
MDIO bus which is still the SF2 master MDIO bus. The reason for that is
because BCM7445 systems were already shipped with a Device Tree blob
looking like this (irrelevant parts omitted for simplicity):
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
phy-mode = "rgmii-txid";
phy-handle = <&phy0>;
reg = <1>;
label = "rgmii_1";
};
...
mdio@403c0 {
...
phy0: ethernet-phy@0 {
broken-turn-around;
device_type = "ethernet-phy";
max-speed = <0x3e8>;
reg = <0>;
compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
};
};
There is a hardware issue with chip revisions (Dx) that lead to the
development of the following commits:
461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
536fab5bf5 ("net: dsa: bcm_sf2: Do not register slave MDIO bus with OF")
b8c6cd1d31 ("net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0")
There should have been an internal MDIO bus node created for the chip
revision (Dx) that suffers from this problem, but it did not happen back
then.
Had that happen, that we should have correctly parented phy@0 (bcm53125
below) as child node of the internal MDIO bus, but the production Device
Tree blob that was shipped with the firmware targeted the fixed version
of the chip, despite both the affected and corrected chips being shipped
into production.
The problem is that of_phy_connect() for port@1 will happily resolve the
'phy-handle' from the mdio@403c0 node, which bypasses the diversion
completely. This results in this double programming that the diversion
refers to and aims to avoid. In order to force of_phy_connect() to fail,
and have DSA call to dsa_slave_phy_connect(), we must deactivate
ethernet-phy@0 from mdio@403c0, and the best way to do that is by
removing the phandle property completely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will need to remove some OF properties in drivers/net/dsa/bcm_sf2.c
with a subsequent commit. Export of_remove_property() to modules so we
can keep bcm_sf2 modular and provide an empty stub for when CONFIG_OF is
disabled to maintain the ability to compile test.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edward Cree says:
====================
sfc: TXQ refactor
Refactor and unify partner-TXQ handling in the EF100 and legacy drivers.
The main thrust of this series is to remove from the legacy (Siena/EF10)
driver the assumption that a netdev TX queue has precisely two hardware
TXQs (checksummed and unchecksummed) associated with it, so that in
future we can have more (e.g. for handling inner-header checksums) or
fewer (e.g. to free up hardware queues for XDP usage).
Changes from v1:
* better explain patch #1 in the commit message, and rename
xmit_more_available to xmit_pending
* add new patch #2 applying the same approach to ef100, for consistency
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use efx_for_each_channel_tx_queue() rather than efx_tx_queue_partner().
Make some related simplifications of efx_nic_tx_is_empty() to remove
entry points that aren't used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of open-coding the calculation with efx_tx_queue_partner(), use
the functions that iterate over numbers of queues other than 2 with
efx_for_each_channel_tx_queue().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As in the Siena/EF10 case, it minimises cacheline ping-pong between
the TX and completion paths.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This should cause no functional change; merely make there only be one
design of xmit_more handling to understand. As with the EF10/Siena
version, we set tx_queue->xmit_pending when we queue up a TX, and
clear it when we ring the doorbell (in ef100_notify_tx_desc).
While we're at it, make ef100_notify_tx_desc static since nothing
outside of ef100_tx.c uses it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of using efx_tx_queue_partner(), which relies on the assumption
that tx_queues_per_channel is 2, efx_tx_send_pending() iterates over
txqs with efx_for_each_channel_tx_queue().
We unconditionally set tx_queue->xmit_pending (renamed from
xmit_more_available), then condition on xmit_more for the call to
efx_tx_send_pending(), which will clear xmit_pending. Thus, after an
xmit_more TX, the doorbell is un-rung and xmit_pending is true.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Otherwise gcc generates warnings if the expression is complicated.
Fixes: 312a0c1709 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
collapse_file() in khugepaged passes PAGE_SIZE as the number of pages to
be read to page_cache_sync_readahead(). The intent was probably to read
a single page. Fix it to use the number of pages to the end of the
window instead.
Fixes: 99cb0dbd47 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <shy828301@gmail.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Eric Biggers <ebiggers@google.com>
Link: https://lkml.kernel.org/r/20200903140844.14194-2-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
CPU0: CPU1:
proc_sys_write
hugetlb_sysctl_handler proc_sys_call_handler
hugetlb_sysctl_handler_common hugetlb_sysctl_handler
table->data = &tmp; hugetlb_sysctl_handler_common
table->data = &tmp;
proc_doulongvec_minmax
do_proc_doulongvec_minmax sysctl_head_finish
__do_proc_doulongvec_minmax unuse_table
i = table->data;
*i = val; // corrupt CPU1's stack
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
The following oops was seen:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Code: Bad RIP value.
...
Call Trace:
? set_max_huge_pages+0x3da/0x4f0
? alloc_pool_huge_page+0x150/0x150
? proc_doulongvec_minmax+0x46/0x60
? hugetlb_sysctl_handler_common+0x1c7/0x200
? nr_hugepages_store+0x20/0x20
? copy_fd_bitmaps+0x170/0x170
? hugetlb_sysctl_handler+0x1e/0x20
? proc_sys_call_handler+0x2f1/0x300
? unregister_sysctl_table+0xb0/0xb0
? __fd_install+0x78/0x100
? proc_sys_write+0x14/0x20
? __vfs_write+0x4d/0x90
? vfs_write+0xef/0x240
? ksys_write+0xc0/0x160
? __ia32_sys_read+0x50/0x50
? __close_fd+0x129/0x150
? __x64_sys_write+0x43/0x50
? do_syscall_64+0x6c/0x200
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e5ff215941 ("hugetlb: multiple hstates for multiple page sizes")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit cf11e85fc0 ("mm: hugetlb: optionally allocate gigantic
hugepages using cma"), the gigantic page would be allocated from node
which is not the preferred node, although there are pages available from
that node. The reason is that the nid parameter has been ignored in
alloc_gigantic_page().
Besides, the __GFP_THISNODE also need be checked if user required to
alloc only from the preferred node.
After this patch, the preferred node is tried first before other allowed
nodes, and don't try to allocate from other nodes if __GFP_THISNODE is
specified. If user don't specify the preferred node, the current node
will be used as preferred node, which makes sure consistent behavior of
allocating gigantic and non-gigantic hugetlb page.
Fixes: cf11e85fc0 ("mm: hugetlb: optionally allocate gigantic hugepages using cma")
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Link: https://lkml.kernel.org/r/20200902025016.697260-1-lixinhai.lxh@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to remove a migration PTE and replace it with a device private
PTE was not copying the soft dirty bit from the migration entry. This
could lead to page contents not being marked dirty when faulting the page
back from device private memory.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200831212222.22409-3-rcampbell@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm/migrate: preserve soft dirty in remove_migration_pte()".
I happened to notice this from code inspection after seeing Alistair
Popple's patch ("mm/rmap: Fixup copying of soft dirty and uffd ptes").
This patch (of 2):
The check for is_zone_device_page() and is_device_private_page() is
unnecessary since the latter is sufficient to determine if the page is a
device private page. Simplify the code for easier reading.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200831212222.22409-1-rcampbell@nvidia.com
Link: https://lkml.kernel.org/r/20200831212222.22409-2-rcampbell@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During memory migration a pte is temporarily replaced with a migration
swap pte. Some pte bits from the existing mapping such as the soft-dirty
and uffd write-protect bits are preserved by copying these to the
temporary migration swap pte.
However these bits are not stored at the same location for swap and
non-swap ptes. Therefore testing these bits requires using the
appropriate helper function for the given pte type.
Unfortunately several code locations were found where the wrong helper
function is being used to test soft_dirty and uffd_wp bits which leads to
them getting incorrectly set or cleared during page-migration.
Fix these by using the correct tests based on pte type.
Fixes: a5430dda8a ("mm/migrate: support un-addressable ZONE_DEVICE page in migration")
Fixes: 8c3328f1f3 ("mm/migrate: migrate_vma() unmap page from vma while collecting pages")
Fixes: f45ec5ff16 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200825064232.10023-2-alistair@popple.id.au
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f45ec5ff16 ("userfaultfd: wp: support swap and page migration")
introduced support for tracking the uffd wp bit during page migration.
However the non-swap PTE variant was used to set the flag for zone device
private pages which are a type of swap page.
This leads to corruption of the swap offset if the original PTE has the
uffd_wp flag set.
Fixes: f45ec5ff16 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Link: https://lkml.kernel.org/r/20200825064232.10023-1-alistair@popple.id.au
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of "capture group (...)" in the immediate condition after `&&`
results in `$1` being uninitialized. This issues a warning "Use of
uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl
line 2638".
I noticed this bug while running checkpatch on the set of commits from
v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in
their commit message.
This bug was introduced in the script by commit e518e9a59e
("checkpatch: emit an error when there's a diff in a changelog"). It
has been in the script since then.
The author intended to store the match made by capture group in variable
`$1`. This should have contained the name of the file as `[\w/]+`
matched. However, this couldn't be accomplished due to usage of capture
group and `$1` in the same regular expression.
Fix this by placing the capture group in the condition before `&&`.
Thus, `$1` can be initialized to the text that capture group matches
thereby setting it to the desired and required value.
Fixes: e518e9a59e ("checkpatch: emit an error when there's a diff in a changelog")
Signed-off-by: Mrinal Pandey <mrinalmni@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Joe Perches <joe@perches.com>
Link: https://lkml.kernel.org/r/20200714032352.f476hanaj2dlmiot@mrinalpandey
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
definition of sysctl_max_threads to match its prototype in
linux/sysctl.h which fixes the following sparse error/warning:
kernel/fork.c:3050:47: warning: incorrect type in argument 3 (different address spaces)
kernel/fork.c:3050:47: expected void *
kernel/fork.c:3050:47: got void [noderef] __user *buffer
kernel/fork.c:3036:5: error: symbol 'sysctl_max_threads' redeclared with different type (incompatible argument 3 (different address spaces)):
kernel/fork.c:3036:5: int extern [addressable] [signed] [toplevel] sysctl_max_threads( ... )
kernel/fork.c: note: in included file (through include/linux/key.h, include/linux/cred.h, include/linux/sched/signal.h, include/linux/sched/cputime.h):
include/linux/sysctl.h:242:5: note: previously declared as:
include/linux/sysctl.h:242:5: int extern [addressable] [signed] [toplevel] sysctl_max_threads( ... )
Fixes: 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200825093647.24263-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IA64 isn't really being maintained, so mark it as Odd Fixes only.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/7e719139-450f-52c2-59a2-7964a34eda1f@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nominate Nathan and myself to be point of contact for clang/LLVM related
support, after a poll at the LLVM BoF at Linux Plumbers Conf 2020.
While corporate sponsorship is beneficial, its important to not entrust
the keys to the nukes with any one entity. Should Nathan and I find
ourselves at the same employer, I would gladly step down.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lkml.kernel.org/r/20200825143540.2948637-1-ndesaulniers@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I am leaving Marvell and already do not have access to my @marvell.com
email address. So switching over to my korg mail address or removing my
address there another maintainer is already listed. For the entries
there no other maintainer is listed I will keep looking into patches for
Cavium systems for a while until someone from Marvell takes it over.
Since I might have limited access to hardware and also limited time I
changed state to 'Odd Fixes' for those entries.
Signed-off-by: Robert Richter <rric@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ganapatrao Kulkarni <gkulkarni@marvell.com>
Cc: Sunil Goutham <sgoutham@marvell.com>
CC: Borislav Petkov <bp@alien8.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <wsa@kernel.org>,
Link: https://lkml.kernel.org/r/20200824122050.31164-1-rric@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 52f2347808 ("mm/slub.c: fix corrupted freechain in
deactivate_slab()") suffered an update when picked up from LKML [1].
Specifically, relocating 'freelist = NULL' into 'freelist_corrupted()'
created a no-op statement. Fix it by sticking to the behavior intended
in the original patch [1]. In addition, make freelist_corrupted()
immune to passing NULL instead of &freelist.
The issue has been spotted via static analysis and code review.
[1] https://lore.kernel.org/linux-mm/20200331031450.12182-1-dongli.zhang@oracle.com/
Fixes: 52f2347808 ("mm/slub.c: fix corrupted freechain in deactivate_slab()")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200824130643.10291-1-erosca@de.adit-jv.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've met softlockup with "CONFIG_PREEMPT_NONE=y", when the target memcg
doesn't have any reclaimable memory.
It can be easily reproduced as below:
watchdog: BUG: soft lockup - CPU#0 stuck for 111s![memcg_test:2204]
CPU: 0 PID: 2204 Comm: memcg_test Not tainted 5.9.0-rc2+ #12
Call Trace:
shrink_lruvec+0x49f/0x640
shrink_node+0x2a6/0x6f0
do_try_to_free_pages+0xe9/0x3e0
try_to_free_mem_cgroup_pages+0xef/0x1f0
try_charge+0x2c1/0x750
mem_cgroup_charge+0xd7/0x240
__add_to_page_cache_locked+0x2fd/0x370
add_to_page_cache_lru+0x4a/0xc0
pagecache_get_page+0x10b/0x2f0
filemap_fault+0x661/0xad0
ext4_filemap_fault+0x2c/0x40
__do_fault+0x4d/0xf9
handle_mm_fault+0x1080/0x1790
It only happens on our 1-vcpu instances, because there's no chance for
oom reaper to run to reclaim the to-be-killed process.
Add a cond_resched() at the upper shrink_node_memcgs() to solve this
issue, this will mean that we will get a scheduling point for each memcg
in the reclaimed hierarchy without any dependency on the reclaimable
memory in that memcg thus making it more predictable.
Suggested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Xunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: http://lkml.kernel.org/r/1598495549-67324-1-git-send-email-xlpang@linux.alibaba.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syzbot has reported an use-after-free in the uncharge_batch path
BUG: KASAN: use-after-free in instrument_atomic_write include/linux/instrumented.h:71 [inline]
BUG: KASAN: use-after-free in atomic64_sub_return include/asm-generic/atomic-instrumented.h:970 [inline]
BUG: KASAN: use-after-free in atomic_long_sub_return include/asm-generic/atomic-long.h:113 [inline]
BUG: KASAN: use-after-free in page_counter_cancel mm/page_counter.c:54 [inline]
BUG: KASAN: use-after-free in page_counter_uncharge+0x3d/0xc0 mm/page_counter.c:155
Write of size 8 at addr ffff8880371c0148 by task syz-executor.0/9304
CPU: 0 PID: 9304 Comm: syz-executor.0 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1f0/0x31e lib/dump_stack.c:118
print_address_description+0x66/0x620 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report+0x132/0x1d0 mm/kasan/report.c:530
check_memory_region_inline mm/kasan/generic.c:183 [inline]
check_memory_region+0x2b5/0x2f0 mm/kasan/generic.c:192
instrument_atomic_write include/linux/instrumented.h:71 [inline]
atomic64_sub_return include/asm-generic/atomic-instrumented.h:970 [inline]
atomic_long_sub_return include/asm-generic/atomic-long.h:113 [inline]
page_counter_cancel mm/page_counter.c:54 [inline]
page_counter_uncharge+0x3d/0xc0 mm/page_counter.c:155
uncharge_batch+0x6c/0x350 mm/memcontrol.c:6764
uncharge_page+0x115/0x430 mm/memcontrol.c:6796
uncharge_list mm/memcontrol.c:6835 [inline]
mem_cgroup_uncharge_list+0x70/0xe0 mm/memcontrol.c:6877
release_pages+0x13a2/0x1550 mm/swap.c:911
tlb_batch_pages_flush mm/mmu_gather.c:49 [inline]
tlb_flush_mmu_free mm/mmu_gather.c:242 [inline]
tlb_flush_mmu+0x780/0x910 mm/mmu_gather.c:249
tlb_finish_mmu+0xcb/0x200 mm/mmu_gather.c:328
exit_mmap+0x296/0x550 mm/mmap.c:3185
__mmput+0x113/0x370 kernel/fork.c:1076
exit_mm+0x4cd/0x550 kernel/exit.c:483
do_exit+0x576/0x1f20 kernel/exit.c:793
do_group_exit+0x161/0x2d0 kernel/exit.c:903
get_signal+0x139b/0x1d30 kernel/signal.c:2743
arch_do_signal+0x33/0x610 arch/x86/kernel/signal.c:811
exit_to_user_mode_loop kernel/entry/common.c:135 [inline]
exit_to_user_mode_prepare+0x8d/0x1b0 kernel/entry/common.c:166
syscall_exit_to_user_mode+0x5e/0x1a0 kernel/entry/common.c:241
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Commit 1a3e1f4096 ("mm: memcontrol: decouple reference counting from
page accounting") reworked the memcg lifetime to be bound the the struct
page rather than charges. It also removed the css_put_many from
uncharge_batch and that is causing the above splat.
uncharge_batch() is supposed to uncharge accumulated charges for all
pages freed from the same memcg. The queuing is done by uncharge_page
which however drops the memcg reference after it adds charges to the
batch. If the current page happens to be the last one holding the
reference for its memcg then the memcg is OK to go and the next page to
be freed will trigger batched uncharge which needs to access the memcg
which is gone already.
Fix the issue by taking a reference for the memcg in the current batch.
Fixes: 1a3e1f4096 ("mm: memcontrol: decouple reference counting from page accounting")
Reported-by: syzbot+b305848212deec86eabe@syzkaller.appspotmail.com
Reported-by: syzbot+b5ea6fb6f139c8b9482b@syzkaller.appspotmail.com
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Hugh Dickins <hughd@google.com>
Link: https://lkml.kernel.org/r/20200820090341.GC5033@dhcp22.suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
uninitialized_var() macro was removed from the sources [1] and
other warning-silencing tricks were deprecated [2]. The purpose of this
cocci script is to prevent new occurrences of uninitialized_var()
open-coded variants.
[1] commit 63a0895d96 ("compiler: Remove uninitialized_var() macro")
[2] commit 4b19bec97c ("docs: deprecated.rst: Add uninitialized_var()")
Cc: Kees Cook <keescook@chromium.org>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
- Fix a broken metadata verifier that would incorrectly validate attr
fork extents of a realtime file against the realtime volume.
-----BEGIN PGP SIGNATURE-----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=5U8o
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.9-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"Fix a broken metadata verifier that would incorrectly validate attr
fork extents of a realtime file against the realtime volume"
* tag 'xfs-5.9-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix xfs_bmap_validate_extent_raw when checking attr fork of rt files
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the xfs filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted xfs filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the ext2 filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted ext2 filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dpsub driver uses the DMA engine API, and thus selects DMA_ENGINE to
provide that API. DMA_ENGINE depends on DMADEVICES, which can be
deselected by the user, creating a possibly unmet indirect dependency:
WARNING: unmet direct dependencies detected for DMA_ENGINE
Depends on [n]: DMADEVICES [=n]
Selected by [m]:
- DRM_ZYNQMP_DPSUB [=m] && HAS_IOMEM [=y] && (ARCH_ZYNQMP || COMPILE_TEST [=y]) && COMMON_CLK [=y] && DRM [=m] && OF [=y]
Add a dependency on DMADEVICES to fix this.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
If we exceed UIO_FASTIOV, we don't handle the transition correctly
between an allocated vec for requests that are queued with IOSQE_ASYNC.
Store the iovec appropriately and re-set it in the iter iov in case
it changed.
Fixes: ff6165b2d7 ("io_uring: retain iov_iter state over io_read/io_write calls")
Reported-by: Nick Hill <nick@nickhill.org>
Tested-by: Norman Maurer <norman.maurer@googlemail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Documentation/DMA-API-HOWTO.txt states that the dma_map_sg() function
returns the number of the created entries in the DMA address space.
However the subsequent calls to the dma_sync_sg_for_{device,cpu}() and
dma_unmap_sg must be called with the original number of the entries
passed to the dma_map_sg().
struct sg_table is a common structure used for describing a non-contiguous
memory buffer, used commonly in the DRM and graphics subsystems. It
consists of a scatterlist with memory pages and DMA addresses (sgl entry),
as well as the number of scatterlist entries: CPU pages (orig_nents entry)
and DMA mapped pages (nents entry).
It turned out that it was a common mistake to misuse nents and orig_nents
entries, calling DMA-mapping functions with a wrong number of entries or
ignoring the number of mapped entries returned by the dma_map_sg()
function.
To avoid such issues, lets use a common dma-mapping wrappers operating
directly on the struct sg_table objects and use scatterlist page
iterators where possible. This, almost always, hides references to the
nents and orig_nents entries, making the code robust, easier to follow
and copy/paste safe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200904131711.12950-27-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If a write delegation isn't available, the Linux NFS client uses
a zero-stateid when performing a SETATTR.
NFSv4.0 provides no mechanism for an NFS server to match such a
request to a particular client. It recalls all delegations for that
file, even delegations held by the client issuing the request. If
that client happens to hold a read delegation, the server will
recall it immediately, resulting in an NFS4ERR_DELAY/CB_RECALL/
DELEGRETURN sequence.
Optimize out this pipeline bubble by having the client return any
delegations it may hold on a file before it issues a
SETATTR(zero-stateid) on that file.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Device tree schema expects NAND controller to be named
"nand-controller", otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dt.yaml: gpmi-nand@8000c000:
$nodename:0: 'gpmi-nand@8000c000' does not match '^nand-controller(@.*)?'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like the other i-MX devices the i.MX6 family can output the enet tx
clock on the pad to feed the connected device. Add the missing clk here
to avoid local fixups like: arch/arm/boot/dts/imx6qdl-tx6.dtsi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The common imx6qdl.dtsi already defines the iomuxc phandle. Make use of
it in the imx6dl.dtsi and imx6q.dtsi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pad QSPI1B_SCLK mux mode 0x1 is for function UART3_DTE_TX,
correct the mux mode.
Fixes: 743636f25f ("ARM: dts: imx: add pin function header for imx6sx")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ROHM BD71847 PMIC has a 32.768 kHz clock. Adding necessary parent
allows to probe the bd718x7 clock driver fixing boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the i.MX board files have been removed, there
is no need for keeping the ehci related files, so just
remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX35 has basic device tree support.
To achieve the goal of converting all i.MX SoCs to a
devicetree-only platform, remove imx35 board files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX31 has basic device tree support.
To achieve the goal of converting all i.MX SoCs to a
devicetree-only platform, remove imx31 board files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX27 has basic device tree support.
To achieve the goal of converting all i.MX SoCs to a
devicetree-only platform, remove imx27 board files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mx21 has not been converted to device tree yet and there is only
one single board that is supported (imx21ads).
To achieve the goal of converting all i.MX SoCs to
devicetree-only platforms, remove imx21 support.
If someone is interested in supporting imx21, patches to add
imx21 devicetree support will be welcome.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct sdma1 ahb clk, otherwise wrong 1:1 clk ratio will be chosed so
that sdma1 function broken. sdma1 should use 1:2 clk, while sdma2/3 use
1:1.
Fixes: 6d9b8d2043 ("arm64: dts: freescale: Add i.MX8MP dtsi support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
