Only the MEDIA_BUS_FMT_RGB666_1X7X3_SPWG,
MEDIA_BUS_FMT_RGB888_1X7X4_SPWG and MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA bus
formats are valid for LVDS panels. Warn at probe time to catch the
common mistake of using an incorrect format, as well as discrepancies
between the bus format and the reported bpc.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629233320.8774-5-laurent.pinchart+renesas@ideasonboard.com
The DRM bus flags reporting on which clock edge the pixel data and sync
signals are sampled or driven don't make sense for LVDS panels, as the
bus then uses sub-clock timings to send data. Drop those flags and add a
warning in the probe function to make sure the mistake won't be
repeated.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629233320.8774-4-laurent.pinchart+renesas@ideasonboard.com
The Satoz SAT050AT40H12R2 panel is an LVDS panel, the
MEDIA_BUS_FMT_RGB888_1X24 bus format is thus incorrect. Set it to the
correct value MEDIA_BUS_FMT_RGB888_1X7X4_SPWG.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629233320.8774-3-laurent.pinchart+renesas@ideasonboard.com
More and more drivers want to get batching requests queued from
block layer, such as mmc, and tcp based storage drivers. Also
current in-tree users have virtio-scsi, virtio-blk and nvme.
For none, we already support batching dispatch.
But for io scheduler, every time we just take one request from scheduler
and pass the single request to blk_mq_dispatch_rq_list(). This way makes
batching dispatch not possible when io scheduler is applied. One reason
is that we don't want to hurt sequential IO performance, becasue IO
merge chance is reduced if more requests are dequeued from scheduler
queue.
Try to support batching dispatch for io scheduler by starting with the
following simple approach:
1) still make sure we can get budget before dequeueing request
2) use hctx->dispatch_busy to evaluate if queue is busy, if it is busy
we fackback to non-batching dispatch, otherwise dequeue as many as
possible requests from scheduler, and pass them to blk_mq_dispatch_rq_list().
Wrt. 2), we use similar policy for none, and turns out that SCSI SSD
performance got improved much.
In future, maybe we can develop more intelligent algorithem for batching
dispatch.
Baolin has tested this patch and found that MMC performance is improved[3].
[1] https://lore.kernel.org/linux-block/20200512075501.GF1531898@T590/#r
[2] https://lore.kernel.org/linux-block/fe6bd8b9-6ed9-b225-f80c-314746133722@grimberg.me/
[3] https://lore.kernel.org/linux-block/CADBw62o9eTQDJ9RvNgEqSpXmg6Xcq=2TxH0Hfxhp29uF2W=TXA@mail.gmail.com/
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass obtained budget count to blk_mq_dispatch_rq_list(), and prepare
for supporting fully batching submission.
With the obtained budget count, it is easier to put extra budgets
in case of .queue_rq failure.
Meantime remove the old 'got_budget' parameter.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE is returned from
.queue_rq, the 'list' variable always holds this rq which isn't
queued to LLD successfully.
So blk_mq_dispatch_rq_list() always returns false from the branch
of '!list_empty(list)'.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move code for getting driver tag and budget into one helper, so
blk_mq_dispatch_rq_list gets a bit simplified, and easier to read.
Meantime move updating of 'no_tag' and 'no_budget_available' into
the branch for handling partial dispatch because that is exactly
consumer of the two local variables.
Also rename the parameter of 'got_budget' as 'ask_budget'.
No functional change.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All requests in the 'list' of blk_mq_dispatch_rq_list belong to same
hctx, so it is better to pass hctx instead of request queue, because
blk-mq's dispatch target is hctx instead of request queue.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk-mq budget is abstract from scsi's device queue depth, and it is
always per-request-queue instead of hctx.
It can be quite absurd to get a budget from one hctx, then dequeue a
request from scheduler queue, and this request may not belong to this
hctx, at least for bfq and deadline.
So fix the mess and always pass request queue to get/put budget
callback.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As reported by the kernel test robot the cros_ec_typec driver fails to
build if the USB_ROLE_SWITCH is not selected, to fix that, add a
dependency on that symbol. This fixes the following build error:
drivers/platform/chrome/cros_ec_typec.c:133: undefined reference to `usb_role_switch_put'
ld: drivers/platform/chrome/cros_ec_typec.o: in function `cros_typec_get_switch_handles':
drivers/platform/chrome/cros_ec_typec.c:108: undefined reference to `fwnode_usb_role_switch_get'
ld: drivers/platform/chrome/cros_ec_typec.c:117: undefined reference to `usb_role_switch_put'
Fixes: 7e7def15fa ("platform/chrome: cros_ec_typec: Add USB mux control")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Use the dma_need_sync helper instead of (not always entirely correctly)
poking into the dma-mapping internals.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200629130359.2690853-5-hch@lst.de
->dev is already assigned at the top of the function, remove the duplicate
one at the end.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200629130359.2690853-4-hch@lst.de
Invert the polarity and better name the flag so that the use case is
properly documented.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200629130359.2690853-3-hch@lst.de
Add a new API to check if calls to dma_sync_single_for_{device,cpu} are
required for a given DMA streaming mapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200629130359.2690853-2-hch@lst.de
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When, at probe time, an SCMI communication failure inhibits the capacity
to query power domains states, such domains should be skipped.
Registering partially initialized SCMI power domains with genpd will
causes kernel panic.
arm-scmi timed out in resp(caller: scmi_power_state_get+0xa4/0xd0)
scmi-power-domain scmi_dev.2: failed to get state for domain 9
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Mem abort info:
ESR = 0x96000006
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000009f3691000
[0000000000000000] pgd=00000009f1ca0003, p4d=00000009f1ca0003, pud=00000009f35ea003, pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
CPU: 2 PID: 381 Comm: bash Not tainted 5.8.0-rc1-00011-gebd118c2cca8 #2
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Jan 3 2020
Internal error: Oops: 96000006 [#1] PREEMPT SMP
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : of_genpd_add_provider_onecell+0x98/0x1f8
lr : of_genpd_add_provider_onecell+0x48/0x1f8
Call trace:
of_genpd_add_provider_onecell+0x98/0x1f8
scmi_pm_domain_probe+0x174/0x1e8
scmi_dev_probe+0x90/0xe0
really_probe+0xe4/0x448
driver_probe_device+0xfc/0x168
device_driver_attach+0x7c/0x88
bind_store+0xe8/0x128
drv_attr_store+0x2c/0x40
sysfs_kf_write+0x4c/0x60
kernfs_fop_write+0x114/0x230
__vfs_write+0x24/0x50
vfs_write+0xbc/0x1e0
ksys_write+0x70/0xf8
__arm64_sys_write+0x24/0x30
el0_svc_common.constprop.3+0x94/0x160
do_el0_svc+0x2c/0x98
el0_sync_handler+0x148/0x1a8
el0_sync+0x158/0x180
Do not register any power domain that failed to be queried with genpd.
Fixes: 898216c97e ("firmware: arm_scmi: add device power domain support using genpd")
Link: https://lore.kernel.org/r/20200619220330.12217-1-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit e5bfb21d98 ("firmware: smccc: Add HAVE_ARM_SMCCC_DISCOVERY to
identify SMCCC v1.1 and above") introduced new config option to identify
the availability of SMCCC discoverability of version and features
transparently hiding the indirect dependency on ARM_PSCI_FW.
Commit 5a897e3ab4 ("firmware: arm_scmi: fix psci dependency") just
worked around the build dependency making SCMI SMC/HVC transport depend
on ARM_PSCI_FW at the time. Since it really just relies on SMCCC directly
and not on ARM_PSCI_FW, let us move to use CONFIG_HAVE_ARM_SMCCC_DISCOVERY
instead of CONFIG_ARM_PSCI_FW.
Link: https://lore.kernel.org/r/20200625101937.51939-1-sudeep.holla@arm.com
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the fast_switch_possible flag is set unconditionally to true.
Based on this, schedutil does not create a thread for frequency
switching and would always use the fast switch path.
However, if the platform does not support SCMI fast channel, we use
polling mode for SCMI message transfer. This may be possible only if
there is dedicated channel for DVFS and all operations are in polling
mode.
Update this by retrieving the fast_switch capability based on the
presence of fast channels in SCMI platform firmware.
Link: https://lore.kernel.org/r/20200617094332.8391-2-nicola.mazzucato@arm.com
Suggested-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a new fast_switch_possible interface to the existing perf_ops to
export the information of whether or not fast_switch is possible for a
given device.
This can be used by the cpufreq driver and framework to choose proper
mechanism for frequency change.
Link: https://lore.kernel.org/r/20200617094332.8391-1-nicola.mazzucato@arm.com
Suggested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Currently the trace event 'scmi_xfer_end' reports the status of the
transfer using the unsigned status field read from the firmware which
may not be easy to interpret. It may also miss to emit any timeouts
that happen in the driver resulting in emitting garbage in the status
field in those scenarios.
Let us use signed integer so that error values are emitted out after
they are mapped from firmware error formats to standard linux error
codes. While at this, also include any timeouts in the driver itself.
Link: https://lore.kernel.org/r/20200609134503.55860-1-sudeep.holla@arm.com
Cc: Jim Quinlan <james.quinlan@broadcom.com>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
At least the version in the header file to fix a compile warning about
the function being unused.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200630124611.23153-1-joro@8bytes.org
Choo! Choo! All aboard the Split Lock Express, with direct service to
Wreckage!
Skip split_lock_verify_msr() if the CPU isn't whitelisted as a possible
SLD-enabled CPU model to avoid writing MSR_TEST_CTRL. MSR_TEST_CTRL
exists, and is writable, on many generations of CPUs. Writing the MSR,
even with '0', can result in bizarre, undocumented behavior.
This fixes a crash on Haswell when resuming from suspend with a live KVM
guest. Because APs use the standard SMP boot flow for resume, they will
go through split_lock_init() and the subsequent RDMSR/WRMSR sequence,
which runs even when sld_state==sld_off to ensure SLD is disabled. On
Haswell (at least, my Haswell), writing MSR_TEST_CTRL with '0' will
succeed and _may_ take the SMT _sibling_ out of VMX root mode.
When KVM has an active guest, KVM performs VMXON as part of CPU onlining
(see kvm_starting_cpu()). Because SMP boot is serialized, the resulting
flow is effectively:
on_each_ap_cpu() {
WRMSR(MSR_TEST_CTRL, 0)
VMXON
}
As a result, the WRMSR can disable VMX on a different CPU that has
already done VMXON. This ultimately results in a #UD on VMPTRLD when
KVM regains control and attempt run its vCPUs.
The above voodoo was confirmed by reworking KVM's VMXON flow to write
MSR_TEST_CTRL prior to VMXON, and to serialize the sequence as above.
Further verification of the insanity was done by redoing VMXON on all
APs after the initial WRMSR->VMXON sequence. The additional VMXON,
which should VM-Fail, occasionally succeeded, and also eliminated the
unexpected #UD on VMPTRLD.
The damage done by writing MSR_TEST_CTRL doesn't appear to be limited
to VMX, e.g. after suspend with an active KVM guest, subsequent reboots
almost always hang (even when fudging VMXON), a #UD on a random Jcc was
observed, suspend/resume stability is qualitatively poor, and so on and
so forth.
kernel BUG at arch/x86/kvm/x86.c:386!
CPU: 1 PID: 2592 Comm: CPU 6/KVM Tainted: G D
Hardware name: ASUS Q87M-E/Q87M-E, BIOS 1102 03/03/2014
RIP: 0010:kvm_spurious_fault+0xf/0x20
Call Trace:
vmx_vcpu_load_vmcs+0x1fb/0x2b0
vmx_vcpu_load+0x3e/0x160
kvm_arch_vcpu_load+0x48/0x260
finish_task_switch+0x140/0x260
__schedule+0x460/0x720
_cond_resched+0x2d/0x40
kvm_arch_vcpu_ioctl_run+0x82e/0x1ca0
kvm_vcpu_ioctl+0x363/0x5c0
ksys_ioctl+0x88/0xa0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x4c/0x170
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: dbaba47085 ("x86/split_lock: Rework the initialization flow of split lock detection")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200605192605.7439-1-sean.j.christopherson@intel.com
Added epoch counter checking to intel_encoder_hotplug
in order to be able process all the connector changes,
besides connection status. Also now any change in connector
would result in epoch counter change, so no multiple checks
are needed.
v2: Renamed change counter to epoch counter. Fixed type name.
v3: Fixed rebase conflict
v4: Remove duplicate drm_edid_equal checks from hdmi and dp,
lets use only once edid property is getting updated and
increment epoch counter from there.
Also lets now call drm_connector_update_edid_property
right after we get edid always to make sure there is a
unified way to handle edid change, without having to
change tons of source code as currently
drm_connector_update_edid_property is called only in
certain cases like reprobing and not right after edid is
actually updated.
v5: Fixed const modifiers, removed blank line
v6: Removed drm specific part from this patch, leaving only
i915 specific changes here.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630002700.5451-4-kunal1.joshi@intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
This counter will be used by drm_helper_probe_detect caller to determine
if anything had changed(including edid, connection status and etc).
Hardware specific driver detect hooks are responsible for updating this
counter when some change is detected to notify the drm part,
which can trigger for example hotplug event.
Also now call drm_connector_update_edid_property
right after we get edid always to make sure there is a
unified way to handle edid change, without having to
change tons of source code as currently
drm_connector_update_edid_property is called only in
certain cases like reprobing and not right after edid is
actually updated.
v2: Added documentation for the new counter. Rename change_counter to
epoch_counter.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105540
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630002700.5451-3-kunal1.joshi@intel.com
Many drivers would benefit from using
drm helper to compare edid, rather
than bothering with own implementation.
v2: Added documentation for this function.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630002700.5451-2-kunal1.joshi@intel.com
Currently there is no null check for a failed memory allocation
on the dsb object and without this a null pointer dereference
error can occur. Fix this by adding a null check.
Note: added a drm_err message in keeping with the error message style
in the function.
Addresses-Coverity: ("Dereference null return")
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616114221.73971-1-colin.king@canonical.com
Bit 8 would be the "global" bit, which does not quite make sense for non-leaf
page table entries. Intel ignores it; AMD ignores it in PDEs and PDPEs, but
reserves it in PML4Es.
Probably, earlier versions of the AMD manual documented it as reserved in PDPEs
as well, and that behavior made it into KVM as well as kvm-unit-tests; fix it.
Cc: stable@vger.kernel.org
Reported-by: Nadav Amit <namit@vmware.com>
Fixes: a0c0feb579 ("KVM: x86: reserve bit 8 of non-leaf PDPEs and PML4Es in 64-bit mode on AMD", 2014-09-03)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In flush_delete_work, instead of flushing each individual pending
delayed work item, cancel and re-queue them for immediate execution.
The waiting isn't needed here because we're already waiting for all
queued work items to complete in gfs2_flush_delete_work. This makes the
code more efficient, but more importantly, it avoids sleeping during a
rhashtable walk, inside rcu_read_lock().
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Log flush operations (gfs2_log_flush()) can target a specific transaction.
But if the function encounters errors (e.g. io errors) and withdraws,
the transaction was only freed it if was queued to one of the ail lists.
If the withdraw occurred before the transaction was queued to the ail1
list, function ail_drain never freed it. The result was:
BUG gfs2_trans: Objects remaining in gfs2_trans on __kmem_cache_shutdown()
This patch makes log_flush() add the targeted transaction to the ail1
list so that function ail_drain() will find and free it properly.
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Callers expect gfs2_inode_lookup to return an inode pointer or ERR_PTR(error).
Commit b66648ad6d caused it to return NULL instead of ERR_PTR(-ESTALE) in
some cases. Fix that.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b66648ad6d ("gfs2: Move inode generation number check into gfs2_inode_lookup")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
bitmap_full() is a shortcut to find_first_zero_bit().
Thus, no need to call it twice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When include/uapi/linux/iommu.h was created it was never
added to the file list in MAINTAINERS.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200605070025.216124-1-jsnitsel@redhat.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move the recently added sg_table wrapper out of CONFIG_IOMMU_SUPPORT to
let the client code copile also when IOMMU support is disabled.
Fixes: 48530d9fab ("iommu: add generic helper for mapping sgtable objects")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200630081756.18526-1-m.szyprowski@samsung.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If NO_DMA=y (e.g. Sun-3 all{mod,yes}-config):
drivers/iommu/dma-iommu.o: In function `iommu_dma_mmap':
dma-iommu.c:(.text+0x92e): undefined reference to `dma_pgprot'
IOMMU_DMA must not be selected, unless HAS_DMA=y.
Hence fix this by making SUN50I_IOMMU depend on HAS_DMA.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200629121146.24011-1-geert@linux-m68k.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- Fix atomicity of affinity update in the GIC driver
- Don't sleep in atomic when waiting for a GICv4.1 RD to respond
- Fix a couple of typos in user-visible messages
-----BEGIN PGP SIGNATURE-----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=x7P8
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix atomicity of affinity update in the GIC driver
- Don't sleep in atomic when waiting for a GICv4.1 RD to respond
- Fix a couple of typos in user-visible messages
The line-speed algorithm clamps the requested value to the supported
range instead of bailing out on unsupported values.
Provide min and max macros and indicate how they are derived instead of
hardcoding the limits.
Note that the algorithm depends on the minimum rate (45.78 bps)
being rounded up (and the maximum rate being rounded down) to avoid
special casing.
Suggested-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/20200630095756.GZ3334@localhost
Signed-off-by: Johan Hovold <johan@kernel.org>
The pte_dma variable in the unmap callback is set but never used. Remove
it.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200628180844.79205-2-maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The flush_all_tlb call back can be called from an atomic context, so using
readl_poll_timeout that embeds a udelay doesn't work.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200628180844.79205-1-maxime@cerno.tech
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There are no users left, all drivers have been converted to use the
per-device private pointer offered by IOMMU core.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200625130836.1916-13-joro@8bytes.org
There are no users left, all drivers have been converted to use the
per-device private pointer offered by IOMMU core.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-12-joro@8bytes.org
There are no users left, all drivers have been converted to use the
per-device private pointer offered by IOMMU core.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-11-joro@8bytes.org
There are no users left, all drivers have been converted to use the
per-device private pointer offered by IOMMU core.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20200625130836.1916-10-joro@8bytes.org
The iommu private pointer is already used in the Mediatek IOMMU v1
driver, so move the dma_iommu_mapping pointer into 'struct
mtk_iommu_data' and do not use dev->archdata.iommu anymore.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-9-joro@8bytes.org
Remove the use of dev->archdata.iommu_domain and use the private
per-device pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-8-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-7-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-6-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-5-joro@8bytes.org
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-4-joro@8bytes.org
