The IPCC hardware block provides a mechanism for triggering interrupts
between co-processors in recent Qualcomm SoCs. This is used as basis for
most form of communication between co-processors, so enable this
support.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-7-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
rather than as a regulator. As such it's available from the rpmhpd as
the SM8250_LCX power domain.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: ec13d5c23a ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
Link: https://lore.kernel.org/r/20200622222747.717306-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SM8250 pinctrl driver provides pin configuration, pin muxing and
GPIO pin control for many pins on the SM8250 SoC.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622220048.717073-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Print sensible string instead of just "(null)" for unknown PMIC models.
Also as we are at it, do not let debugfs handler access past pmic_models
array.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200525164817.2938638-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
John Stultz reported that commit f9288fcc5c ("i2c: designware: Move
ACPI parts into common module") caused a regression on the HiKey board
where adv7511 HDMI bridge driver wasn't probing anymore due the I2C bus
failed to start.
It seems the change caused the bus speed being zero when CONFIG_ACPI
not set and neither speed based on "clock-frequency" device property
or default fast mode is set.
Fix this by splitting i2c_dw_acpi_adjust_bus_speed() to
i2c_dw_acpi_round_bus_speed() and i2c_dw_adjust_bus_speed(), where
the latter one has the code that runs independently of ACPI.
Fixes: f9288fcc5c ("i2c: designware: Move ACPI parts into common module")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl7x2lwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPiVAgAn/83Vx/YrF9sr0+TLzukzfOubJVK
Majxb0I06De23VDExiDoZjh5CnCN3kDja0m2c543ZI1XOrHRbp09v1goJQkAgiT0
AQ8Npi1KB71io18SbZtrAhPLmSiUgRirF+XWHB38qjdbZixvZyWz8nvSITFY8aJQ
ICgbm5jftzBdSOKEhqbHwZ+LcXjEGZsehwTiHpUBKUR/kNlRFV5UFAd5m+CT5i4O
3DydLIReATDCoZUKfkBjYtoR3c9DyWESyfWD4GZ/2xRKr/1QfiZ4dA0cd/P9hJYz
7MAG+ULvJGlasSzmcEQJ/X3o9QuIJzpQFpwbKeMX6gOsEsSVUQeriUHIFA==
=jTFw
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"All bugfixes except for a couple cleanup patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Remove vcpu_vmx's defunct copy of host_pkru
KVM: x86: allow TSC to differ by NTP correction bounds without TSC scaling
KVM: X86: Fix MSR range of APIC registers in X2APIC mode
KVM: VMX: Stop context switching MSR_IA32_UMWAIT_CONTROL
KVM: nVMX: Plumb L2 GPA through to PML emulation
KVM: x86/mmu: Avoid mixing gpa_t with gfn_t in walk_addr_generic()
KVM: LAPIC: ensure APIC map is up to date on concurrent update requests
kvm: lapic: fix broken vcpu hotplug
Revert "KVM: VMX: Micro-optimize vmexit time when not exposing PMU"
KVM: VMX: Add helpers to identify interrupt type from intr_info
kvm/svm: disable KCSAN for svm_vcpu_run()
KVM: MIPS: Fix a build error for !CPU_LOONGSON64
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() notify to report HPD. This provides the
necessary API to support disabling connector creation, do so by
accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in dw_hdmi_bridge_attach().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-23-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_connector explicitly to the internal functions that require it.
The functions that still access the connector from the dw_hdmi structure
are dw_hdmi_connector_create() and __dw_hdmi_probe(). The former access
is expected, as that's where the internal connector is created. The
latter will be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-22-laurent.pinchart+renesas@ideasonboard.com
Store the connector that the bridge is currently wired to in the dw_hdmi
structure. This is currently identical to the connector field, but will
differ once the driver supports disabling connector creation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-21-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer
is passed to the callers where required, particularly to the
dw_hdmi_phy_ops .init() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
Several internal functions take a drm_display_mode argument to configure
the HDMI encoder or the HDMI PHY. They must not modify the mode, make
the pointer const to enforce that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-18-laurent.pinchart+renesas@ideasonboard.com
Replace the drm_connector pointer passed to the .mode_valid() function
with a const drm_display_info pointer, as that's all the function should
need. Use the display info passed to the bridge .mode_valid() operation
instead of retrieving it from the connector, to prepare for make
connector creation optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-16-laurent.pinchart+renesas@ideasonboard.com
The meson-dw-hdmi driver needs to access its own context from the
.mode_valid() operation. It currently gets it from the dev_private field
of the drm_device retrieved from the connector, which is a hack. Use the
private data passed to the .mode_valid() operation instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-15-laurent.pinchart+renesas@ideasonboard.com
The .configure_phy() operation takes a dw_hdmi_plat_data pointer as a
context argument. This differs from .mode_valid() that takes a custom
private context pointer, causing possible confusion. Make the
dw_hdmi_plat_data operations more consistent by passing the private
context pointer to .configure_phy() as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-13-laurent.pinchart+renesas@ideasonboard.com
Platform glue drivers for dw_hdmi may need to access device-specific
data from their .mode_valid() implementation. They currently have no
clean way to do so, and one driver hacks around it by accessing the
dev_private data of the drm_device retrieved from the connector.
Add a priv_data void pointer to the dw_hdmi_plat_data structure, and
pass it to the .mode_valid() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-12-laurent.pinchart+renesas@ideasonboard.com
When the user consumes and generates sqe at a fast rate,
io_sqring_entries can always get sqe, and ret will not be equal to -EBUSY,
so that io_sq_thread will never call cond_resched or schedule, and then
we will get the following system error prompt:
rcu: INFO: rcu_sched self-detected stall on CPU
or
watchdog: BUG: soft lockup-CPU#23 stuck for 112s! [io_uring-sq:1863]
This patch checks whether need to call cond_resched() by checking
the need_resched() function every cycle.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
The drm_hdmi_avi_infoframe_from_display_mode(),
drm_hdmi_vendor_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range() functions take a drm_connector that
they don't modify. Mark it as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-10-laurent.pinchart+renesas@ideasonboard.com
Instead of poking into the DT node of the next bridge for its DDC bus
and implementing the .get_modes() and .detect() connector operations
manually, retrieve the next bridge in the chain and delegate these
operations to it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-7-laurent.pinchart+renesas@ideasonboard.com
The drm_bridge_get_edid() function is documented to return an error
pointer on error. The underlying .get_edid() operation, however, returns
NULL on error, and so do the drm_get_edid() and drm_do_get_edid()
functions upon which .get_edid() is usually implemented. Make
drm_bridge_get_edid() return NULL on error to be consistent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-6-laurent.pinchart+renesas@ideasonboard.com
Now that the driver supports all the connector-related bridge
operations, make the connector creation optional. This enables usage of
the adv7511 with the DRM bridge connector helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-5-laurent.pinchart+renesas@ideasonboard.com
Implement the bridge connector-related .get_edid(), .detect() and
.hpd_notify() operations, and report the related bridge capabilities.
Output status detection is implemented using the same backend as for the
DRM connector, but requires making mode retrieval at detection time
optional as no pointer to the connector is available to the bridge
.detect() operation. The reason for the need to retrieve modes at
detection time is unclear to me, and this may benefit from further
refactoring of hot plug handling code.
Hot plug detection is notified through the bridge HPD notification
framework when the bridge is used without creating a connector, and
falls back to the existing implementation otherwise. CEC handling of
disconnection is handled in the new .hpd_notify() operation in the new
code path.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-4-laurent.pinchart+renesas@ideasonboard.com
The main DRM device is actually a virtual device so it doesn't have the
iommus property, which is instead on the DMA masters, in this case the
mixers.
Add a call to of_dma_configure with the mixers DT node but on the DRM
virtual device to configure it in the same way than the mixers.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/9a4daf438dd3f2fe07afb23688bfb793a0613d7d.1589378833.git-series.maxime@cerno.tech
(cherry picked from commit b718102dbd)
[Maxime: Applied to -fixes since it missed the merge window and display is
broken without it]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory node requires a unit-address. For some boards the bootloader,
which is usually locked down, uses a hard-coded name for the memory node
without a unit-address, so we can't fix it on those boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The I/O and PLL supplies used for HDMI/DP have alternative names. Use
the names that are given in the hardware documentation for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller's parent clock depends on the output that's
consuming data from the display controller, so it needs to be specified
as the parent of the corresponding output. The device tree bindings do
specify this, so just correct the existing device trees that get this
wrong.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Interrupt names are used to distinguish between the syncpoint and
general host1x interrupts. Make sure they are available in the DT so
that drivers can use them if necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While the host1x controller found on Tegra132 is the same as on Tegra124
it is good practice to also list a SoC-specific compatible string so any
SoC-specific quirks can be implemented in drivers if necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra194, all clients of the memory subsystem can generally address
40 bits of system memory. However, bit 39 has special meaning and will
cause the memory controller to reorder sectors for block-linear buffer
formats. This is primarily useful for graphics-related devices.
Use of bit 39 must be controlled on a case-by-case basis. Buffers that
are used with bit 39 set by one device may be used with bit 39 cleared
by other devices.
Care must be taken to allocate buffers at addresses that do not require
bit 39 to be set. This is normally not an issue for system memory since
there are no Tegra-based systems with enough RAM to exhaust the 39-bit
physical address space. However, when a device is behind an IOMMU, such
as the ARM SMMU on Tegra194, the IOMMUs input address space can cause
IOVA allocations to happen in this region. This is for example the case
when an operating system implements a top-down allocation policy for IO
virtual addresses.
To account for this, describe the path that memory accesses take through
the system. Memory clients will send requests to the memory controller,
which forwards bits [38:0] of the address either to the external memory
controller or the SMMU, depending on the stream ID of the access. A good
way to describe this is using the interconnects bindings, see:
Documentation/devicetree/bindings/interconnect/interconnect.txt
The standard "dma-mem" path is used to describe the path towards system
memory via the memory controller. A dma-ranges property in the memory
controller's device tree node limits the range of DMA addresses that the
memory clients can use to bits [38:0], ensuring that bit 39 is not used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v4:
- add additional entries for interconnect-names to match interconnects
- add EMC as destination for interconnect paths
Changes in v3:
- add missing interconnect properties for VIC
Changes in v2:
- use memory client IDs instead of stream IDs (Mikko Perttunen)
Signed-off-by: Thierry Reding <treding@nvidia.com>
The interface used by clients of the memory controller can be configured
in a number of different ways. Describe this path using the interconnect
bindings to enable the configuration of these parameters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI on Tegra210 is in fact not compatible with the one found on
Tegra124. Remove the extra compatible string to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI on Tegra194 is in fact not compatible with the one found on
Tegra186. Remove the extra compatible string to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
