According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The macro is defined as SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn),
so imx290_power_off must be the 1st arg, and imx290_power_on the 2nd.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
preview_init_entities() does not call v4l2_ctrl_handler_free() when
it fails.
Add the missed function to fix it.
Fixes: de1135d44f ("[media] omap3isp: CCDC, preview engine and resizer")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mccic_register() forgets to cleanup the notifier in its error handler.
mccic_shutdown() also misses calling v4l2_async_notifier_cleanup().
Add the missed calls to fix them.
Fixes: 3eefe36cc0 ("media: marvell-ccic: use async notifier to get the sensor")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the ACPI id of ov2740 camera sensor was registered as "INT3474",
current ov2740 driver is supposed to be working with ACPI only.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the convenience function pm_runtime_get_if_active() instead of a
number of calls to runtime PM to figure out if the device was already
powered up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When v4l2_async_register_subdev_sensor_common() returns
an error code, a pairing runtime PM usage counter
decrement is needed to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cec_adapter struct contained a waitq field that isn't used
anywhere, so drop this.
It also contained a phys_addrs array to store any reported physical
addresses. However, this was never actually used, so this field is
removed as well. The original idea was to let the core keep track of
this information, but nothing was ever done with this. Should this
be needed in the future then it is easy enough to resurrect this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Declare bison header file output so that C files can depend upon them.
As there are multiple output targets $@ is replaced by the target name.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200619043356.90024-7-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
These will break the build as soon as we stop disabling all warnings
when building flex and bison generated files, so add them before we do
that to keep the tree bisectable.
Noticed when building on centos:7 with NO_LIBBPF=1:
util/expr.c: In function 'key_equal':
util/expr.c:29:2: error: implicit declaration of function 'strcmp' [-Werror=implicit-function-declaration]
return !strcmp((const char *)key1, (const char *)key2);
^
util/expr.c: In function 'expr__add_id':
util/expr.c:40:3: error: implicit declaration of function 'malloc' [-Werror=implicit-function-declaration]
val_ptr = malloc(sizeof(double));
^
util/expr.c:40:13: error: incompatible implicit declaration of built-in function 'malloc' [-Werror]
val_ptr = malloc(sizeof(double));
^
util/expr.c:42:12: error: 'ENOMEM' undeclared (first use in this function)
return -ENOMEM;
^
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The CEC_ADAP_G_CAPS documentation of the cec_caps struct was missing
the available_log_addrs field. Add this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
budget_register() has no error handling after its failure.
Add the missed undo functions for error handling to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MyGica T230* receivers also do DVB-C and DVB-T: change their names.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CONFIG_DVB_USB_CXUSB_ANALOG is a 'bool' symbol with a dependency on the
tristate CONFIG_VIDEO_V4L2, which means it can be enabled as =y even
when its dependency is =m. This leads to a link failure:
drivers/media/usb/dvb-usb/cxusb-analog.o: In function `cxusb_medion_analog_init':
cxusb-analog.c:(.text+0x92): undefined reference to `v4l2_subdev_call_wrappers'
drivers/media/usb/dvb-usb/cxusb-analog.o: In function `cxusb_medion_register_analog':
cxusb-analog.c:(.text+0x466): undefined reference to `v4l2_device_register'
cxusb-analog.c:(.text+0x4c3): undefined reference to `v4l2_i2c_new_subdev'
cxusb-analog.c:(.text+0x4fb): undefined reference to `v4l2_subdev_call_wrappers'
...
Change the dependency only disallow the analog portion of the driver
in that configuration.
Fixes: e478d40540 ("media: cxusb: add analog mode support for Medion MD95700")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This has been maintained for some time, update MAINTAINERS to reflect.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IR Droid / IR Toy device used custom protocol over serial
line, so it is presenting itself as CDC ACM device.
Now that we have proper in-kernel driver for it we need to black-list the
device in cdc-acm driver.
http://dangerousprototypes.com/docs/USB_Infrared_Toyhttps://www.irdroid.com/irdroid-usb-ir-transceiver/
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media documents under the uAPI should be GFDL compatible.
So, make this one dual-licensed GPL-2.0 or GFDL-1.1+ with
no-invariant sections.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add fallback pio feature in case dma transfer failed before start.
Besides, another whole pio transfer including setup_transfer will be
issued by spi core, no need to restore jobs like commit bcd8e7761e ("spi:
imx: fallback to PIO if dma setup failure").
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-3-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback to pio mode in case dma transfer failed with error status
SPI_TRANS_FAIL_NO_START.
If spi client driver want to enable this feature please set xfer->error in
the proper place such as dmaengine_prep_slave_sg() failure detect(but no
any data put into spi bus yet). Besides, add master->fallback checking in
its can_dma() so that spi core could switch to pio next time. Please refer
to spi-imx.c.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-2-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Data RAM on the device have to be powered on before starting to download
the firmware.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Co-developed-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Data RAM on the device have to be powered on before starting to download
the firmware.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Running a guest with a virtio-iommu protecting virtio devices
is broken since commit 515e5b6d90 ("dma-mapping: use vmap insted
of reimplementing it"). Before the conversion, the size was
page aligned in __get_vm_area_node(). Doing so fixes the
regression.
Fixes: 515e5b6d90 ("dma-mapping: use vmap insted of reimplementing it")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The dma coherent pool code needs genalloc. Move the select over
from DMA_REMAP, which doesn't actually need it.
Fixes: dbed452a07 ("dma-pool: decouple DMA_REMAP from DMA_COHERENT_POOL")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Rientjes <rientjes@google.com>
When a coherent mapping is created in dma_direct_alloc_pages(), it needs
to be decrypted if the device requires unencrypted DMA before returning.
Fixes: 3acac06550 ("dma-mapping: merge the generic remapping helpers into dma-direct")
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When specifying insanely large debug buffers a kernel warning is
printed. The debug code does handle the error gracefully, though.
Instead of duplicating the check let us silence the warning to
avoid crashes when panic_on_warn is used.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Currently if early_pgm_check_handler is called it ends up in pgm check
loop. The problem is that early_pgm_check_handler is instrumented by
KASAN but executed without DAT flag enabled which leads to addressing
exception when KASAN checks try to access shadow memory.
Fix that by executing early handlers with DAT flag on under KASAN as
expected.
Reported-and-tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When single stepping an svc instruction on s390, the kernel is entered
with a PER program check interruption. The program check handler than
jumps to the system call handler by reloading the PSW. The code didn't
set GPR13 to the thread pointer in struct task_struct. This made the
kernel access invalid memory while trying to fetch the syscall function
address. Fix this by always assigned GPR13 after .Lsysc_per.
Fixes: 0b0ed657fe ("s390: remove critical section cleanup from entry.S")
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Setting the stateful encoder capture frame interval is only supported
if this flag is set. Document this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the V4L2_FMT_FLAG_ENC_CAP_FRAME_INTERVAL flag to signal that
the coded frame interval can be set separately from the raw frame
interval for stateful encoders.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add missing periods at the end of two sentences.
Although mandatory -> Although not mandatory
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This documentation is very outdated. In particular, it is
not obvious at all that this is used to change the framerate of
sensors.
Fix it, and include references to the stateful encoder API where
this works slightly different.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Due to complexity of the video encoding process, the V4L2 drivers of
stateful encoder hardware require specific sequences of V4L2 API calls
to be followed. These include capability enumeration, initialization,
encoding, encode parameters change, drain and reset.
Specifics of the above have been discussed during Media Workshops at
LinuxCon Europe 2012 in Barcelona and then later Embedded Linux
Conference Europe 2014 in Düsseldorf. The de facto Codec API that
originated at those events was later implemented by the drivers we already
have merged in mainline, such as s5p-mfc or coda.
The only thing missing was the real specification included as a part of
Linux Media documentation. Fix it now and document the encoder part of
the Codec API.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While looking at reboot issues and module load/unload tests, I found
out some resources allocated in the dailink .init() callback are not
properly released - there is no existing mechanism in the soc-core to
do so.
The addition of a dailink .exit() callback seems to be the simplest
solution overall. It can be argued that the existing machine platform
device .remove() callback can also perform the necessary cleanups,
however as shown in the last two examples this might require a loop to
identify components whereas the dailink .exit() already has all the
necessary information to revert the actions done in the .init() step.
Changes since RFC:
Better commit messages and explanations
rt5682 cases with snd_soc_component_set_jack() called in the .exit()
Fred Oh (2):
ASoC: intel: sof_rt5682: move disabling jack to dai link's exit()
ASoC: intel: cml_rt1011_rt5682: disable jack in dailink .exit()
Pierre-Louis Bossart (3):
ASoC: soc-link: introduce exit() callback
ASoC: Intel: bdw-rt5677: fix module load/unload issues
ASoC: Intel: kbl-rt5660: use .exit() dailink callback to release gpiod
include/sound/soc-link.h | 1 +
include/sound/soc.h | 3 +++
sound/soc/intel/boards/bdw-rt5677.c | 18 ++++++++++++++--
sound/soc/intel/boards/cml_rt1011_rt5682.c | 8 ++++++++
sound/soc/intel/boards/kbl_rt5660.c | 17 +++++++++++++--
sound/soc/intel/boards/sof_rt5682.c | 24 ++++++++--------------
sound/soc/soc-core.c | 3 +++
sound/soc/soc-link.c | 6 ++++++
8 files changed, 60 insertions(+), 20 deletions(-)
base-commit: 39853b1438
--
2.20.1
KASAN throws the following warning in rt1011.c:
[ 170.777603] BUG: KASAN: stack-out-of-bounds in _find_next_bit.constprop.0+0x3e/0xf0
find_next_bit() relies on unsigned long pointer arguments, but this driver
uses a type cast that generates the KASAN warning. Replace find_next_bit()
and find_last_bit() with __ffs() and __fls() to pass the value and avoid
casting pointers to make the warning go away.
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200622151348.28063-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "ret" in fsl_easrc_set_ctx_format is not initialized, then
the unknown value maybe returned by this function.
Fixes: 955ac62405 ("ASoC: fsl_easrc: Add EASRC ASoC CPU DAI drivers")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1592816611-16297-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a cache_hints module param to control per-queue user space cache
hints support.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
That if-statement seems to be unneeded.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We moved cache management decision making to the upper layer and
rely on buffer's need_cache_sync flags and videobuf2 core. If the
upper layer (core) has decided to invoke ->prepare() or ->finish()
then we must sync.
For DMABUF ->need_cache_sync_on_prepare and ->need_cache_sync_on_flush
are always false so videobuf core does not call ->prepare() and
->finish() on such buffers.
Additionally, scratch the DMABUF comment.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide begin_cpu_access() and end_cpu_access() dma_buf_ops
callbacks for cache synchronisation on exported buffers.
V4L2_FLAG_MEMORY_NON_CONSISTENT has no effect on dma-sg buffers.
dma-sg allocates memory using the page allocator directly, so
there is no memory consistency guarantee.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide begin_cpu_access() and end_cpu_access() callbacks for
cache synchronisation on exported buffers.
The patch also adds a new helper function - vb2_dc_buffer_consistent(),
which returns true is if the buffer is consistent (DMA_ATTR_NON_CONSISTENT
bit cleared), so then we don't need to sync anything.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This simplifies the code a tiny bit and let's us to avoid
unneeded ->prepare()/->finish() calls.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
