The Tegra EMC scaling support code is not a clock provider, but merely a
clock consumer, and thus does not need to include
<linux/clk-provider.h>.
Fixes: 0bf368c5b2cf ("memory: tegra: Add EMC scaling support code for Tegra210")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to tegra_bpmp_get() must be balanced by a call to
tegra_bpmp_put() in case of error, as already done in the remove
function.
Add an error handling path and corresponding goto.
Fixes: 52d15dd23f ("memory: tegra: Support DVFS on Tegra186 and later")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory clock-rate change could be running on a non-boot CPU, while the
boot CPU handles the EMC interrupt. This introduces an unnecessary latency
since boot CPU should handle the interrupt and then notify the sibling CPU
about clock-rate change completion. In some rare cases boot CPU could be
in uninterruptible state for a significant time (like in a case of KASAN +
NFS root), it could get to the point that completion timeouts before boot
CPU gets a chance to handle interrupt. The solution is to get rid of the
completion and replace it with interrupt-status polling.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory clock-rate change could be running on a non-boot CPU, while the
boot CPU handles the EMC interrupt. This introduces an unnecessary latency
since boot CPU should handle the interrupt and then notify the sibling CPU
about clock-rate change completion. In some rare cases boot CPU could be
in uninterruptible state for a significant time (like in a case of KASAN +
NFS root), it could get to the point that completion timeouts before boot
CPU gets a chance to handle interrupt. The solution is to get rid of the
completion and replace it with interrupt-status polling.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Derated timings are used to ensure that the memory chips keep operating
correctly at high temperatures. This adds code to support polling of the
chip operating state when high temperatures are measured on the chip and
change the refresh mode accordingly. Under very high temperatures, the
driver will switch to the derated tables to ensure proper operation of
the memory chips.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch includes the sequence for clock tuning and the dynamic
training mechanism for the clock above 800MHz.
And historically there have been different sequences to change the EMC
clock. The sequence to be used is specified in the EMC table.
However, for the currently supported upstreaming platform, only the most
recent sequence is used. So only support that in this patch.
Based on the work of Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is the initial patch for Tegra210 EMC frequency scaling. It has the
code to program various aspects of the EMC that are standardized, but it
does not yet include the specific programming sequence needed for clock
scaling.
The driver is designed to support LPDDR4 SDRAM. Devices that use LPDDR4
need to perform training of the RAM before it can be used. Firmware will
perform this training during early boot and pass a table of supported
frequencies to the kernel via device tree.
For the frequencies above 800 MHz, periodic retraining is needed to
compensate for changes in timing. This periodic training will have to be
performed until the frequency drops back to or below 800 MHz.
This driver provides helpers used during this runtime retraining that
will be used by the sequence specific code in a follow-up patch.
Based on work by Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace the symbolic permissions with octals in order to make them
readable.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than a plain-vanilla init/exit, this patch provides 3 steps in
the initialization needed for driver selection, machine driver
selection and deal with power rail dependencies.
- ACPI scan: this step is done at a very early stage to detect the
presence of a SoundWire Controller and enabled links at the BIOS
level. This step may be called from the legacy HDaudio driver, which
will abort its probe to let the Sound Open Firmware (SOF) handle the
hardware.
- probe: this step allocates all the required memory and will add a
sdw_bus, which in turn will result in identifying all possible Slaves
listed below the Controller ACPI companion device. All the information
is reported to the parent PCI driver which will select the relevant
machine driver.
- startup: this last step starts the bus reset, which results in Slave
devices reporting as ATTACHED and being enumerated. This step is only
done during the card creation stage, after the DSP is powered to
account for internal power rail dependencies.
These 3 steps are already supported in the Sound Open firmware
drivers and upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's not clear how this code ever worked, the link information is used
in intel.c but never passed as platform_data.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to test link_mask twice
Suggested-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The use of drvdata mixes two structures. There was no harm the first
structure is embedded as the first element of the second, but that's
not good. Make sure all drvdata is based on the 'sdw_cdns' structure.
While we are at it, remove indirections for 'dev' and 'cdns' to make
the code more readable.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code can be simplified a bit to have a more consistent use of
'dev' and 'bus', as well as move definitions around. This will help
make the major changes in follow-up patches easier to review.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a collection of mostly small fixes, mostly fixing fallout from
some of the DPCM changes that went in last time around which shook out
some issues on i.MX and Qualcomm platforms. The addition of a managed
version of snd_soc_register_dai() is to fix resource leaks.
There's also a few new device IDs for x86 systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl7wlcQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0K9NB/0e4qOoGEyxmf6rbAnT1zvBu0vQu2qR
ABkcCztt/tS/QJ1BSDHX/hALj9jr6RuAtn1pL4ynVGxJ86TByrrwLX1WhtKTk+DW
TEgiPrFAKLlCwLVxgFdF0LORicv5zZEehi9+zP1HKt31Zsv2KNvTtwaF1WymIEd5
LYVvYhtAKMmpjPN2WjlDSuita+fc/e5dm26n8hi3DJKIBVsLBbSxd1s1kwlqqnPh
KbJjVrp5sWNhCyKu2hW8Sv1ovh40WbZ1TnzlDTiLinz0TCyqUyqEatuJ4RgRLmsW
G3IAvm0rNjqyIF8TbQvYvvMZ0BZe/2SHdNXBtOXjXUYxhmnLvfAXocTf
=FNgB
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.8-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.8
This is a collection of mostly small fixes, mostly fixing fallout from
some of the DPCM changes that went in last time around which shook out
some issues on i.MX and Qualcomm platforms. The addition of a managed
version of snd_soc_register_dai() is to fix resource leaks.
There's also a few new device IDs for x86 systems.
The dais are allocated with devm_kcalloc() but their name isn't
resourced managed and never freed. Fix by also using devm_ for the dai
names as well.
Fixes: c46302ec55 ('soundwire: intel: Add audio DAI ops')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200617163536.17401-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Converts the ast driver to drm_info(), drm_err() and drm_WARN_*(). No
functional changes are made.
v2:
* also convert WARN_*() macros
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617080340.29584-5-tzimmermann@suse.de
All upcasting from struct drm_device to struct ast_private is now
performed via to_ast_private(). Using struct drm_device.dev_private
is deprecated. The ast variable in ast_crtc_helper_atomic_check() is
unused, so removed it.
v2:
* fix typo in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617080340.29584-4-tzimmermann@suse.de
The ast driver contains code paths for AST 1180 chips. The chip is not
supported and the rsp code has never been tested. Simplify the driver by
removing the AST 1180 code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617080340.29584-2-tzimmermann@suse.de
`-objs` is designed for building host programs, change to `-y`,
more straightforward for device drivers.
See Documentation/kbuild/makefiles.rst
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200616162140.2563535-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Export finalize function to client which helps append eoc and jump
command to pkt. Let client decide call finalize or not.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/1592749115-24158-9-git-send-email-dennis-yc.hsieh@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We currently decide to execute the PtrAuth save/restore code based
on a set of branches that evaluate as (ARM64_HAS_ADDRESS_AUTH_ARCH ||
ARM64_HAS_ADDRESS_AUTH_IMP_DEF). This can be easily replaced by
a much simpler test as the ARM64_HAS_ADDRESS_AUTH capability is
exactly this expression.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When save/restoring PtrAuth registers between host and guest, it is
pretty useless to fetch the in-memory state, while we have the right
state in the HCR_EL2 system register. Use that instead.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that the scene is set for enabling PtrAuth on non-VHE, drop
the restrictions preventing userspace from enabling it.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We currently prevent PtrAuth from even being built if KVM is selected,
but VHE isn't. It is a bit of a pointless restriction, since we also
check this at run time (rejecting the enabling of PtrAuth for the
vcpu if we're not running with VHE).
Just drop this apparently useless restriction.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
While initializing EL2, enable Address Authentication if detected
from EL1. We still use the EL1-provided keys though.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Building the current 5.8 kernel for an e500 machine with
CONFIG_RANDOMIZE_BASE=y and CONFIG_BLOCK=n yields the following
failure:
arch/powerpc/mm/nohash/kaslr_booke.c: In function 'kaslr_early_init':
arch/powerpc/mm/nohash/kaslr_booke.c:387:2: error: implicit
declaration of function 'flush_icache_range'; did you mean 'flush_tlb_range'?
Indeed, including asm/cacheflush.h into kaslr_booke.c fixes the build.
Fixes: 2b0e86cc5d ("powerpc/fsl_booke/32: implement KASLR infrastructure")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Scott Wood <oss@buserror.net>
[mpe: Tweak change log to mention CONFIG_BLOCK=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200613162801.1946619-1-asolokha@kb.kras.ru
Move ptep_get() close to pte_update(), in an ifdef section already
dedicated to powerpc 8xx. This section contains explanation about
the layout of page table entries.
Also modify it to return 4 times the pte value instead of padding
with zeroes.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/9f2df6621fcaf9eba15fadc61c169d0c8e2fb849.1592481938.git.christophe.leroy@csgroup.eu
With hash translation, the hypervisor can hint the LPAR about 16GB contiguous range
via ibm,expected#pages. The kernel marks the range specified in the device tree
as reserved. Avoid doing this when using radix translation. Radix translation
only supports 1G gigantic hugepage and kernel can do the 1G gigantic hugepage
allocation via early memblock reservation. This can be done because with radix
translation pages are not required to be contiguous on the host.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200622064019.16682-1-aneesh.kumar@linux.ibm.com
Add rpm smd clocks, PMIC and bus clocks which are required on
SDM630/660 (and APQ variants) for clients to vote on.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200622090252.36568-1-konradybcio@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Right now the driver uses only 3 LED modes:
0: On
1: HW Blinking (Interval 1)
3: Off
However, the controller supports a second HW blinking interval, which results
in 4 possible LED modes:
0: On
1: HW Blinking (Interval 1)
2: HW Blinking (Interval 2)
3: Off
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Drop the pointless and needlessly confusing casts of struct-device
pointers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 8d3b6a4001 ("leds: wm831x-status: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot use devres so that
deregistration ends up being tied to the parent device, something which
leads to use-after-free on driver unbind when the class device is
released while still being registered.
Fixes: 11e1bbc116 ("leds: lm36274: Introduce the TI LM36274 LED driver")
Cc: stable <stable@vger.kernel.org> # 5.3
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 50154e29e5 ("leds: lm3533: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: eed16255d6 ("leds: da903x: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 375446df95 ("leds: 88pm860x: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
clang points out that doing arithmetic between diffent enums is usually
a mistake:
drivers/leds/leds-lm355x.c:167:28: warning: bitwise operation between different enumeration types ('enum lm355x_tx2' and 'enum lm355x_ntc') [-Wenum-enum-conversion]
reg_val = pdata->pin_tx2 | pdata->ntc_pin;
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
drivers/leds/leds-lm355x.c:178:28: warning: bitwise operation between different enumeration types ('enum lm355x_tx2' and 'enum lm355x_ntc') [-Wenum-enum-conversion]
reg_val = pdata->pin_tx2 | pdata->ntc_pin | pdata->pass_mode;
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
In this driver, it is intentional, so add a cast to hide the false-positive
warning. It appears to be the only instance of this warning at the moment.
Fixes: b98d13c725 ("leds: Add new LED driver for lm355x chips")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The documentation reports the wrong macro names
related to the pca9532 instead of the pca955x
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Introduce couple of helpers to enable or disable input. i.e.
lp_gpio_enable_input() and lp_gpio_disable_input().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
