commit 92452b1760 upstream.
The mask setting is 5 bits wide for the ad9434
(ref. data sheet register 0x18 FLEX_VREF). Apparently the settings
from ad9265 were copied by mistake when support for the device was added
to the driver.
Fixes: 4606d0f4b0 ("iio: adc: ad9467: add support for AD9434 high-speed ADC")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8f15d1df2 upstream.
The sensors IIS328DQ and H3LIS331DL share one configuration but
H3LIS331DL has different gain parameters, configs therefore
need to be split up.
The gain parameters for the IIS328DQ are 0.98, 1.95 and 3.91,
depending on the selected measurement range.
See sensor manuals, chapter 2.1 "mechanical characteristics",
parameter "Sensitivity".
Datasheet: https://www.st.com/resource/en/datasheet/iis328dq.pdf
Datasheet: https://www.st.com/resource/en/datasheet/h3lis331dl.pdf
Fixes: 46e33707fe ("iio: accel: add support for IIS328DQ variant")
Reviewed-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Signed-off-by: Markus Koeniger <markus.koeniger@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ff39d6de4 upstream.
fwnode_irq_get_byname() returns a negative value on failure; if a negative
value is returned, use it as `err` argument for dev_err_probe().
While at it, add a missing trailing newline to the dev_err_probe() error
message.
Fixes: df36de1367 ("iio: accel: add ADXL380 driver")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48e6a9c4a2 upstream.
Calling of_platform_populate() without a match table will only populate
the immediate child nodes under /firmware. This is usually fine, but in
the case of something like a "simple-mfd" node such as
"raspberrypi,bcm2835-firmware", those child nodes will not be populated.
And subsequent calls won't work either because the /firmware node is
marked as processed already.
Switch the call to of_platform_default_populate() to solve this problem.
It should be a nop for existing cases.
Fixes: 3aa0582fdb ("of: platform: populate /firmware/ node from of_platform_default_populate_init()")
Cc: stable@vger.kernel.org
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://patch.msgid.link/20260114015158.692170-2-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81122fba08 upstream.
of_find_node_by_path() returns a device_node with its refcount
incremented. When kstrtoint() fails or dt_alloc() fails, the function
continues to the next iteration without calling of_node_put(), causing
a reference count leak.
Add of_node_put(np) before continue on both error paths to properly
release the device_node reference.
Fixes: 611cad7201 ("dt: add of_alias_scan and of_alias_get_id")
Cc: stable@vger.kernel.org
Signed-off-by: Weigang He <geoffreyhe2@gmail.com>
Link: https://patch.msgid.link/20260117091238.481243-1-geoffreyhe2@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1883cefd3 upstream.
Before this change the LED was added to leds_list before led_init_core()
gets called adding it the list before led_classdev.set_brightness_work gets
initialized.
This leaves a window where led_trigger_register() of a LED's default
trigger will call led_trigger_set() which calls led_set_brightness()
which in turn will end up queueing the *uninitialized*
led_classdev.set_brightness_work.
This race gets hit by the lenovo-thinkpad-t14s EC driver which registers
2 LEDs with a default trigger provided by snd_ctl_led.ko in quick
succession. The first led_classdev_register() causes an async modprobe of
snd_ctl_led to run and that async modprobe manages to exactly hit
the window where the second LED is on the leds_list without led_init_core()
being called for it, resulting in:
------------[ cut here ]------------
WARNING: CPU: 11 PID: 5608 at kernel/workqueue.c:4234 __flush_work+0x344/0x390
Hardware name: LENOVO 21N2S01F0B/21N2S01F0B, BIOS N42ET93W (2.23 ) 09/01/2025
...
Call trace:
__flush_work+0x344/0x390 (P)
flush_work+0x2c/0x50
led_trigger_set+0x1c8/0x340
led_trigger_register+0x17c/0x1c0
led_trigger_register_simple+0x84/0xe8
snd_ctl_led_init+0x40/0xf88 [snd_ctl_led]
do_one_initcall+0x5c/0x318
do_init_module+0x9c/0x2b8
load_module+0x7e0/0x998
Close the race window by moving the adding of the LED to leds_list to
after the led_init_core() call.
Cc: stable@vger.kernel.org
Fixes: d23a22a74f ("leds: delay led_set_brightness if stopping soft-blink")
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Link: https://patch.msgid.link/20251211163727.366441-1-johannes.goede@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6342969daf ]
TPM2_Unseal[1] expects the handle of a loaded data object, and not the
handle of the parent key. But the tpm2_unseal_cmd provides the parent
keyhandle instead of blob_handle for the session HMAC calculation. This
causes unseal to fail.
Fix this by passing blob_handle to tpm_buf_append_name().
References:
[1] trustedcomputinggroup.org/wp-content/uploads/
Trusted-Platform-Module-2.0-Library-Part-3-Version-184_pub.pdf
Fixes: 6e9722e9a7 ("tpm2-sessions: Fix out of range indexing in name_size")
Signed-off-by: Srish Srinivasan <ssrish@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c2615c842 ]
In tpm_buf_check_hmac_response(), compare the HMAC values in constant
time using crypto_memneq() instead of in variable time using memcmp().
This is worthwhile to follow best practices and to be consistent with
MAC comparisons elsewhere in the kernel. However, in this driver the
side channel seems to have been benign: the HMAC input data is
guaranteed to always be unique, which makes the usual MAC forgery via
timing side channel not possible. Specifically, the HMAC input data in
tpm_buf_check_hmac_response() includes the "our_nonce" field, which was
generated by the kernel earlier, remains under the control of the
kernel, and is unique for each call to tpm_buf_check_hmac_response().
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Stable-dep-of: 6342969daf ("keys/trusted_keys: fix handle passed to tpm_buf_append_name during unseal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 614da1d3d4 ]
There's a big comment in the x86 do_page_fault() about our interrupt
disabling code:
* User address page fault handling might have reenabled
* interrupts. Fixing up all potential exit points of
* do_user_addr_fault() and its leaf functions is just not
* doable w/o creating an unholy mess or turning the code
* upside down.
but it turns out that comment is subtly wrong, and the code as a result
is also wrong.
Because it's certainly true that we may have re-enabled interrupts when
handling user page faults. And it's most certainly true that we don't
want to bother fixing up all the cases.
But what isn't true is that it's limited to user address page faults.
The confusion stems from the fact that we have logic here that depends
on the address range of the access, but other code then depends on the
_context_ the access was done in. The two are not related, even though
both of them are about user-vs-kernel.
In other words, both user and kernel addresses can cause interrupts to
have been enabled (eg when __bad_area_nosemaphore() gets called for user
accesses to kernel addresses). As a result we should make sure to
disable interrupts again regardless of the address range before
returning to the low-level fault handling code.
The __bad_area_nosemaphore() code actually did disable interrupts again
after enabling them, just not consistently. Ironically, as noted in the
original comment, fixing up all the cases is just not worth it, when the
simple solution is to just do it unconditionally in one single place.
So remove the incomplete case that unsuccessfully tried to do what the
comment said was "not doable" in commit ca4c6a9858 ("x86/traps: Make
interrupt enable/disable symmetric in C code"), and just make it do the
simple and straightforward thing.
Signed-off-by: Cedric Xing <cedric.xing@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Fixes: ca4c6a9858 ("x86/traps: Make interrupt enable/disable symmetric in C code")
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ddbaaaaf ]
Modify the internal registration helpers dpll_xa_ref_{dpll,pin}_add()
to reject duplicate registration attempts.
Previously, if a caller attempted to register the same pin multiple
times (with the same ops, priv, and cookie) on the same device, the core
silently increments the reference count and return success. This behavior
is incorrect because if the caller makes these duplicate registrations
then for the first one dpll_pin_registration is allocated and for others
the associated dpll_pin_ref.refcount is incremented. During the first
unregistration the associated dpll_pin_registration is freed and for
others WARN is fired.
Fix this by updating the logic to return `-EEXIST` if a matching
registration is found to enforce a strict "register once" policy.
Fixes: 9431063ad3 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260121130012.112606-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ee784fdf0 ]
The virtio transports derives its TX credit directly from peer_buf_alloc,
which is set from the remote endpoint's SO_VM_SOCKETS_BUFFER_SIZE value.
On the host side this means that the amount of data we are willing to
queue for a connection is scaled by a guest-chosen buffer size, rather
than the host's own vsock configuration. A malicious guest can advertise
a large buffer and read slowly, causing the host to allocate a
correspondingly large amount of sk_buff memory.
The same thing would happen in the guest with a malicious host, since
virtio transports share the same code base.
Introduce a small helper, virtio_transport_tx_buf_size(), that
returns min(peer_buf_alloc, buf_alloc), and use it wherever we consume
peer_buf_alloc.
This ensures the effective TX window is bounded by both the peer's
advertised buffer and our own buf_alloc (already clamped to
buffer_max_size via SO_VM_SOCKETS_BUFFER_MAX_SIZE), so a remote peer
cannot force the other to queue more data than allowed by its own
vsock settings.
On an unpatched Ubuntu 22.04 host (~64 GiB RAM), running a PoC with
32 guest vsock connections advertising 2 GiB each and reading slowly
drove Slab/SUnreclaim from ~0.5 GiB to ~57 GiB; the system only
recovered after killing the QEMU process. That said, if QEMU memory is
limited with cgroups, the maximum memory used will be limited.
With this patch applied:
Before:
MemFree: ~61.6 GiB
Slab: ~142 MiB
SUnreclaim: ~117 MiB
After 32 high-credit connections:
MemFree: ~61.5 GiB
Slab: ~178 MiB
SUnreclaim: ~152 MiB
Only ~35 MiB increase in Slab/SUnreclaim, no host OOM, and the guest
remains responsive.
Compatibility with non-virtio transports:
- VMCI uses the AF_VSOCK buffer knobs to size its queue pairs per
socket based on the local vsk->buffer_* values; the remote side
cannot enlarge those queues beyond what the local endpoint
configured.
- Hyper-V's vsock transport uses fixed-size VMBus ring buffers and
an MTU bound; there is no peer-controlled credit field comparable
to peer_buf_alloc, and the remote endpoint cannot drive in-flight
kernel memory above those ring sizes.
- The loopback path reuses virtio_transport_common.c, so it
naturally follows the same semantics as the virtio transport.
This change is limited to virtio_transport_common.c and thus affects
virtio-vsock, vhost-vsock, and loopback, bringing them in line with the
"remote window intersected with local policy" behaviour that VMCI and
Hyper-V already effectively have.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Melbin K Mathew <mlbnkm1@gmail.com>
[Stefano: small adjustments after changing the previous patch]
[Stefano: tweak the commit message]
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20260121093628.9941-4-sgarzare@redhat.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a98de8013 ]
The test requires the sender (client) to send all messages before waking
up the receiver (server).
Since virtio-vsock had a bug and did not respect the size of the TX
buffer, this test worked, but now that we are going to fix the bug, the
test hangs because the sender would fill the TX buffer before waking up
the receiver.
Set the buffer size in the sender (client) as well, as we already do for
the receiver (server).
Fixes: 5c338112e4 ("test/vsock: rework message bounds test")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260121093628.9941-3-sgarzare@redhat.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef3d52a1a ]
The credit calculation in virtio_transport_get_credit() uses unsigned
arithmetic:
ret = vvs->peer_buf_alloc - (vvs->tx_cnt - vvs->peer_fwd_cnt);
If the peer shrinks its advertised buffer (peer_buf_alloc) while bytes
are in flight, the subtraction can underflow and produce a large
positive value, potentially allowing more data to be queued than the
peer can handle.
Reuse virtio_transport_has_space() which already handles this case and
add a comment to make it clear why we are doing that.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Melbin K Mathew <mlbnkm1@gmail.com>
[Stefano: use virtio_transport_has_space() instead of duplicating the code]
[Stefano: tweak the commit message]
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20260121093628.9941-2-sgarzare@redhat.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc4816bdb0 ]
In ovs_vport_get_upcall_stats(), some statistics protected by
u64_stats_sync, are read and accumulated in ignorance of possible
u64_stats_fetch_retry() events. These statistics are already accumulated
by u64_stats_inc(). Fix this by reading them into temporary variables
first.
Fixes: 1933ea365a ("net: openvswitch: Add support to count upcall packets")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20260121072932.2360971-1-mmyangfl@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfca045cd4 ]
Prior to the blamed commit, the bridge_num range was from
0 to ds->max_num_bridges - 1. After the commit, it is from
1 to ds->max_num_bridges.
So this check:
if (bridge_num >= max)
return 0;
must be updated to:
if (bridge_num > max)
return 0;
in order to allow the last bridge_num value (==max) to be used.
This is easiest visible when a driver sets ds->max_num_bridges=1.
The observed behaviour is that even the first created bridge triggers
the netlink extack "Range of offloadable bridges exceeded" warning, and
is handled in software rather than being offloaded.
Fixes: 3f9bb0301d ("net: dsa: make dp->bridge_num one-based")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260120211039.3228999-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9b329096 ]
After 3cbf4ffba5 ("net: plumb network namespace into __skb_flow_dissect")
we have to provide a net pointer to __skb_flow_dissect(),
either via skb->dev, skb->sk, or a user provided pointer.
In the following case, syzbot was able to cook a bare skb.
WARNING: net/core/flow_dissector.c:1131 at __skb_flow_dissect+0xb57/0x68b0 net/core/flow_dissector.c:1131, CPU#1: syz.2.1418/11053
Call Trace:
<TASK>
bond_flow_dissect drivers/net/bonding/bond_main.c:4093 [inline]
__bond_xmit_hash+0x2d7/0xba0 drivers/net/bonding/bond_main.c:4157
bond_xmit_hash_xdp drivers/net/bonding/bond_main.c:4208 [inline]
bond_xdp_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5139 [inline]
bond_xdp_get_xmit_slave+0x1fd/0x710 drivers/net/bonding/bond_main.c:5515
xdp_master_redirect+0x13f/0x2c0 net/core/filter.c:4388
bpf_prog_run_xdp include/net/xdp.h:700 [inline]
bpf_test_run+0x6b2/0x7d0 net/bpf/test_run.c:421
bpf_prog_test_run_xdp+0x795/0x10e0 net/bpf/test_run.c:1390
bpf_prog_test_run+0x2c7/0x340 kernel/bpf/syscall.c:4703
__sys_bpf+0x562/0x860 kernel/bpf/syscall.c:6182
__do_sys_bpf kernel/bpf/syscall.c:6274 [inline]
__se_sys_bpf kernel/bpf/syscall.c:6272 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:6272
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xec/0xf80 arch/x86/entry/syscall_64.c:94
Fixes: 58deb77cc5 ("bonding: balance ICMP echoes in layer3+4 mode")
Reported-by: syzbot+c46409299c70a221415e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/696faa23.050a0220.4cb9c.001f.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matteo Croce <mcroce@redhat.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260120161744.1893263-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04708606fd ]
Both send_mcast4() and send_mcast6() use sleep 2 to wait for the tunnel
connection between the gateway and the relay, and for the listener
socket to be created in the LISTENER namespace.
However, tests sometimes fail because packets are sent before the
connection is fully established.
Increase the waiting time to make the tests more reliable, and use
wait_local_port_listen() to explicitly wait for the listener socket.
Fixes: c08e8baea7 ("selftests: add amt interface selftest script")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20260120133930.863845-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8215794403 ]
When the parameter pmac_id_valid argument of be_cmd_get_mac_from_list() is
set to false, the driver may request the PMAC_ID from the firmware of the
network card, and this function will store that PMAC_ID at the provided
address pmac_id. This is the contract of this function.
However, there is a location within the driver where both
pmac_id_valid == false and pmac_id == NULL are being passed. This could
result in dereferencing a NULL pointer.
To resolve this issue, it is necessary to pass the address of a stub
variable to the function.
Fixes: 95046b927a ("be2net: refactor MAC-addr setup code")
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://patch.msgid.link/20260120113734.20193-1-a.vatoropin@crpt.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0bd10792d ]
* Implement missing DCB connectors in uconn.c previously defined in conn.h.
* Replace kernel WARN_ON macro with printk message to more gracefully signify
an unknown connector was encountered.
With this patch, unknown connectors are explicitly marked with value 0
(DCB_CONNECTOR_VGA) to match the tested current behavior. Although 0xff
(DCB_CONNECTOR_NONE) may be more suitable, I don't want to introduce a
breaking change.
Fixes: 8b7d92cad9 ("drm/nouveau/kms/nv50-: create connectors based on nvkm info")
Link: https://download.nvidia.com/open-gpu-doc/DCB/1/DCB-4.0-Specification.html#_connector_table_entry
Signed-off-by: Alex Ramírez <lxrmrz732@rocketmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[Lyude: Remove unneeded parenthesis around nvkm_warn()]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251213005327.9495-3-lxrmrz732@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3036b4ce4b ]
* Add missing DCB connectors in conn.h as per the NVIDIA DCB specification.
A lot of connector logic was rewritten for Linux v6.5; some display connector types
went unaccounted-for which caused kernel warnings on devices with the now-unsupported
DCB connectors. This patch adds all of the DCB connectors as defined by NVIDIA to the
dcb_connector_type enum to bring back support for these connectors to the new logic.
Fixes: 8b7d92cad9 ("drm/nouveau/kms/nv50-: create connectors based on nvkm info")
Link: https://download.nvidia.com/open-gpu-doc/DCB/1/DCB-4.0-Specification.html#_connector_table_entry
Signed-off-by: Alex Ramírez <lxrmrz732@rocketmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[Lyude: Clarify DCB_CONNECTOR_HDMI_0 weirdness in comments]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251213005327.9495-2-lxrmrz732@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764a90eb02 ]
Radeon 430 and 520 are OEM GPUs from 2016~2017
They have the same device id: 0x6611 and revision: 0x87
On the Radeon 430, powertune is buggy and throttles the GPU,
never allowing it to reach its maximum SCLK. Work around this
bug by raising the TDP limits we program to the SMC from
24W (specified by the VBIOS on Radeon 430) to 32W.
Disabling powertune entirely is not a viable workaround,
because it causes the Radeon 520 to heat up above 100 C,
which I prefer to avoid.
Additionally, revise the maximum SCLK limit. Considering the
above issue, these GPUs never reached a high SCLK on Linux,
and the workarounds were added before the GPUs were released,
so the workaround likely didn't target these specifically.
Use 780 MHz (the maximum SCLK according to the VBIOS on the
Radeon 430). Note that the Radeon 520 VBIOS has a higher
maximum SCLK: 905 MHz, but in practice it doesn't seem to
perform better with the higher clock, only heats up more.
v2:
Move the workaround to si_populate_smc_tdp_limits.
Fixes: 841686df9f ("drm/amdgpu: add SI DPM support (v4)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 966d70f1e1)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5077426e1 ]
There is no reason to clear the SMC table.
We also don't need to recalculate the power limit then.
Fixes: 841686df9f ("drm/amdgpu: add SI DPM support (v4)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e214d62625)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98c88dc8a1 ]
Samuel and Alex reported regressions of the util_avg of RT rq with
commit 17e3e88ed0 ("sched/fair: Fix pelt lost idle time detection").
It happens that fair is updating and syncing the pelt clock with task one
when pick_next_task_fair() fails to pick a task but before the prev
scheduling class got a chance to update its pelt signals.
Move update_idle_rq_clock_pelt() in set_next_task_idle() which is called
after prev class has been called.
Fixes: 17e3e88ed0 ("sched/fair: Fix pelt lost idle time detection")
Closes: https://lore.kernel.org/all/CAG2KctpO6VKS6GN4QWDji0t92_gNBJ7HjjXrE+6H+RwRXt=iLg@mail.gmail.com/
Closes: https://lore.kernel.org/all/8cf19bf0e0054dcfed70e9935029201694f1bb5a.camel@mediatek.com/
Reported-by: Samuel Wu <wusamuel@google.com>
Reported-by: Alex Hoh <Alex.Hoh@mediatek.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Samuel Wu <wusamuel@google.com>
Tested-by: Alex Hoh <Alex.Hoh@mediatek.com>
Link: https://patch.msgid.link/20260121163317.505635-1-vincent.guittot@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c06343be0b ]
The "valid" readout delay between the two reads of the watchdog is larger
than the valid delta between the resulting watchdog and clocksource
intervals, which results in false positive watchdog results.
Assume TSC is the clocksource and HPET is the watchdog and both have a
uncertainty margin of 250us (default). The watchdog readout does:
1) wdnow = read(HPET);
2) csnow = read(TSC);
3) wdend = read(HPET);
The valid window for the delta between #1 and #3 is calculated by the
uncertainty margins of the watchdog and the clocksource:
m = 2 * watchdog.uncertainty_margin + cs.uncertainty margin;
which results in 750us for the TSC/HPET case.
The actual interval comparison uses a smaller margin:
m = watchdog.uncertainty_margin + cs.uncertainty margin;
which results in 500us for the TSC/HPET case.
That means the following scenario will trigger the watchdog:
Watchdog cycle N:
1) wdnow[N] = read(HPET);
2) csnow[N] = read(TSC);
3) wdend[N] = read(HPET);
Assume the delay between #1 and #2 is 100us and the delay between #1 and
Watchdog cycle N + 1:
4) wdnow[N + 1] = read(HPET);
5) csnow[N + 1] = read(TSC);
6) wdend[N + 1] = read(HPET);
If the delay between #4 and #6 is within the 750us margin then any delay
between #4 and #5 which is larger than 600us will fail the interval check
and mark the TSC unstable because the intervals are calculated against the
previous value:
wd_int = wdnow[N + 1] - wdnow[N];
cs_int = csnow[N + 1] - csnow[N];
Putting the above delays in place this results in:
cs_int = (wdnow[N + 1] + 610us) - (wdnow[N] + 100us);
-> cs_int = wd_int + 510us;
which is obviously larger than the allowed 500us margin and results in
marking TSC unstable.
Fix this by using the same margin as the interval comparison. If the delay
between two watchdog reads is larger than that, then the readout was either
disturbed by interconnect congestion, NMIs or SMIs.
Fixes: 4ac1dd3245 ("clocksource: Set cs_watchdog_read() checks based on .uncertainty_margin")
Reported-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/lkml/20250602223251.496591-1-daniel@quora.org/
Link: https://patch.msgid.link/87bjjxc9dq.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7159e960f ]
The usbnet driver initializes net->max_mtu to ETH_MAX_MTU before calling
the device's bind() callback. When the bind() callback sets
dev->hard_mtu based the device's actual capability (from CDC Ethernet's
wMaxSegmentSize descriptor), max_mtu is never updated to reflect this
hardware limitation).
This allows userspace (DHCP or IPv6 RA) to configure MTU larger than the
device can handle, leading to silent packet drops when the backend sends
packet exceeding the device's buffer size.
Fix this by limiting net->max_mtu to the device's hard_mtu after the
bind callback returns.
See https://gitlab.com/qemu-project/qemu/-/issues/3268 and
https://bugs.passt.top/attachment.cgi?bugid=189
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://bugs.passt.top/show_bug.cgi?id=189
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Link: https://patch.msgid.link/20260119075518.2774373-1-lvivier@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a063f96d8 ]
syzbot found that ndisc_router_discovery() could read and write
in6_dev->ra_mtu without holding a lock [1]
This looks fine, IFLA_INET6_RA_MTU is best effort.
Add READ_ONCE()/WRITE_ONCE() to document the race.
Note that we might also reject illegal MTU values
(mtu < IPV6_MIN_MTU || mtu > skb->dev->mtu) in a future patch.
[1]
BUG: KCSAN: data-race in ndisc_router_discovery / ndisc_router_discovery
read to 0xffff888119809c20 of 4 bytes by task 25817 on cpu 1:
ndisc_router_discovery+0x151d/0x1c90 net/ipv6/ndisc.c:1558
ndisc_rcv+0x2ad/0x3d0 net/ipv6/ndisc.c:1841
icmpv6_rcv+0xe5a/0x12f0 net/ipv6/icmp.c:989
ip6_protocol_deliver_rcu+0xb2a/0x10d0 net/ipv6/ip6_input.c:438
ip6_input_finish+0xf0/0x1d0 net/ipv6/ip6_input.c:489
NF_HOOK include/linux/netfilter.h:318 [inline]
ip6_input+0x5e/0x140 net/ipv6/ip6_input.c:500
ip6_mc_input+0x27c/0x470 net/ipv6/ip6_input.c:590
dst_input include/net/dst.h:474 [inline]
ip6_rcv_finish+0x336/0x340 net/ipv6/ip6_input.c:79
...
write to 0xffff888119809c20 of 4 bytes by task 25816 on cpu 0:
ndisc_router_discovery+0x155a/0x1c90 net/ipv6/ndisc.c:1559
ndisc_rcv+0x2ad/0x3d0 net/ipv6/ndisc.c:1841
icmpv6_rcv+0xe5a/0x12f0 net/ipv6/icmp.c:989
ip6_protocol_deliver_rcu+0xb2a/0x10d0 net/ipv6/ip6_input.c:438
ip6_input_finish+0xf0/0x1d0 net/ipv6/ip6_input.c:489
NF_HOOK include/linux/netfilter.h:318 [inline]
ip6_input+0x5e/0x140 net/ipv6/ip6_input.c:500
ip6_mc_input+0x27c/0x470 net/ipv6/ip6_input.c:590
dst_input include/net/dst.h:474 [inline]
ip6_rcv_finish+0x336/0x340 net/ipv6/ip6_input.c:79
...
value changed: 0x00000000 -> 0xe5400659
Fixes: 49b99da2c9 ("ipv6: add IFLA_INET6_RA_MTU to expose mtu value")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rocco Yue <rocco.yue@mediatek.com>
Link: https://patch.msgid.link/20260118152941.2563857-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d57c67c956 ]
HCLGE_FD_AD_COUNTER_NUM_M should be at GENMASK(19, 13),
rather than at GENMASK(20, 13), because bit 20 is
HCLGE_FD_AD_NXT_STEP_B.
This patch corrects the wrong definition.
Fixes: 1173286802 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260119132840.410513-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 302e5b481c ]
In be_get_new_eqd(), statistics of pkts, protected by u64_stats_sync, are
read and accumulated in ignorance of possible u64_stats_fetch_retry()
events. Before the commit in question, these statistics were retrieved
one by one directly from queues. Fix this by reading them into temporary
variables first.
Fixes: 2094777041 ("be2net: set interrupt moderation for Skyhawk-R using EQ-DB")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260119153440.1440578-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 748a81c8ce ]
In hns3_fetch_stats(), ring statistics, protected by u64_stats_sync, are
read and accumulated in ignorance of possible u64_stats_fetch_retry()
events. These statistics are already accumulated by
hns3_ring_stats_update(). Fix this by reading them into a temporary
buffer first.
Fixes: b20d7fe51e ("net: hns3: add some statitics info to tx process")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260119160759.1455950-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f406220eb8 ]
Several ioctl functions have the ability to call ice_get_rxfh, however
all of these ioctl functions do not provide all of the expected
information in ethtool_rxfh_param. For example, ethtool_get_rxfh_indir does
not provide an rss_key. This previously caused ethtool_get_rxfh_indir to
always fail with -EINVAL.
This change draws inspiration from i40e_get_rss to handle this
situation, by only calling the appropriate rss helpers when the
necessary information has been provided via ethtool_rxfh_param.
Fixes: b66a972abb ("ice: Refactor ice_set/get_rss into LUT and key specific functions")
Signed-off-by: Cody Haas <chaas@riotgames.com>
Closes: https://lore.kernel.org/intel-wired-lan/CAH7f-UKkJV8MLY7zCdgCrGE55whRhbGAXvgkDnwgiZ9gUZT7_w@mail.gmail.com/
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812062e74a ]
Possibility of no FW trace available after update in the fw_trace_mask due
to asynchronous mode of command consumption in the FW.
To ensure FW trace is available after update, wait for FW trace log update
command completion from the FW.
Fixes: cc1aeedb98 ("drm/imagination: Implement firmware infrastructure and META FW support")
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Matt Coster <matt.coster@imgtec.com>
Link: https://patch.msgid.link/20260108040936.129769-1-brajesh.gupta@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b971191fc ]
On at least the HyperX Cloud III, the range is 18944 (-18944 -> 0 in
steps of 1), so the original check for 255 steps is definitely obsolete.
Let's give ourselves a little more headroom before we emit a warning.
Fixes: 80acefff3b ("ALSA: usb-audio - Add volume range check and warn if it too big")
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: linux-sound@vger.kernel.org
Signed-off-by: Arun Raghavan <arunr@valvesoftware.com>
Link: https://patch.msgid.link/20260116225804.3845935-1-arunr@valvesoftware.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19bc5f2a69 ]
In qla27xx_copy_fpin_pkt() and qla27xx_copy_multiple_pkt(), the frame_size
reported by firmware is used to calculate the copy length into
item->iocb. However, the iocb member is defined as a fixed-size 64-byte
array within struct purex_item.
If the reported frame_size exceeds 64 bytes, subsequent memcpy calls will
overflow the iocb member boundary. While extra memory might be allocated,
this cross-member write is unsafe and triggers warnings under
CONFIG_FORTIFY_SOURCE.
Fix this by capping total_bytes to the size of the iocb member (64 bytes)
before allocation and copying. This ensures all copies remain within the
bounds of the destination structure member.
Fixes: 875386b988 ("scsi: qla2xxx: Add Unsolicited LS Request and Response Support for NVMe")
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Reviewed-by: Himanshu Madhani <hmadhani2024@gmail.com>
Link: https://patch.msgid.link/20260106205344.18031-1-jiashengjiangcool@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2f8ad6f0 ]
The fragile ordering between marking commands completed or failed so
that the error handler only wakes when the last running command
completes or times out has race conditions. These race conditions can
cause the SCSI layer to fail to wake the error handler, leaving I/O
through the SCSI host stuck as the error state cannot advance.
First, there is an memory ordering issue within scsi_dec_host_busy().
The write which clears SCMD_STATE_INFLIGHT may be reordered with reads
counting in scsi_host_busy(). While the local CPU will see its own
write, reordering can allow other CPUs in scsi_dec_host_busy() or
scsi_eh_inc_host_failed() to see a raised busy count, causing no CPU to
see a host busy equal to the host_failed count.
This race condition can be prevented with a memory barrier on the error
path to force the write to be visible before counting host busy
commands.
Second, there is a general ordering issue with scsi_eh_inc_host_failed(). By
counting busy commands before incrementing host_failed, it can race with a
final command in scsi_dec_host_busy(), such that scsi_dec_host_busy() does
not see host_failed incremented but scsi_eh_inc_host_failed() counts busy
commands before SCMD_STATE_INFLIGHT is cleared by scsi_dec_host_busy(),
resulting in neither waking the error handler task.
This needs the call to scsi_host_busy() to be moved after host_failed is
incremented to close the race condition.
Fixes: 6eb045e092 ("scsi: core: avoid host-wide host_busy counter for scsi_mq")
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260113161036.6730-1-djeffery@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bf1877b70 ]
The tmp buffer is allocated using kcalloc() but is not freed if
acpi_evaluate_dsm() fails. This causes a memory leak in the error path.
Fix this by explicitly freeing the tmp buffer in the error handling
path of acpi_evaluate_dsm().
Fixes: 58e82a6266 ("platform/x86/amd: Add support for AMD ACPI based Wifi band RFI mitigation feature")
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://patch.msgid.link/20260106091318.747019-1-zilin@seu.edu.cn
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaa9bb1d39 ]
On RV32, updating the 64-bit stimecmp (or vstimecmp) CSR requires two
separate 32-bit writes. A race condition exists if the timer triggers
during these two writes.
The RISC-V Privileged Specification (e.g., Section 3.2.1 for mtimecmp)
recommends a specific 3-step sequence to avoid spurious interrupts
when updating 64-bit comparison registers on 32-bit systems:
1. Set the low-order bits (stimecmp) to all ones (ULONG_MAX).
2. Set the high-order bits (stimecmph) to the desired value.
3. Set the low-order bits (stimecmp) to the desired value.
Current implementation writes the LSB first without ensuring a future
value, which may lead to a transient state where the 64-bit comparison
is incorrectly evaluated as "expired" by the hardware. This results in
spurious timer interrupts.
This patch adopts the spec-recommended 3-step sequence to ensure the
intermediate 64-bit state is never smaller than the current time.
Fixes: 9f7a8ff639 ("RISC-V: Prefer sstc extension if available")
Signed-off-by: Naohiko Shimizu <naohiko.shimizu@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://patch.msgid.link/20260104135938.524-2-naohiko.shimizu@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baaecfcac5 ]
When running make nconfig with a static linking host toolchain,
the libraries are linked in an incorrect order,
resulting in errors similar to the following:
$ MAKEFLAGS='HOSTCC=cc\ -static' make nconfig
/usr/bin/ld: /usr/lib64/gcc/x86_64-unknown-linux-gnu/14.2.1/../../../../lib64/libpanel.a(p_new.o): in function `new_panel':
(.text+0x13): undefined reference to `_nc_panelhook_sp'
/usr/bin/ld: (.text+0x6c): undefined reference to `_nc_panelhook_sp'
Fixes: 1c5af5cf93 ("kconfig: refactor ncurses package checks for building mconf and nconf")
Signed-off-by: Arusekk <floss@arusekk.pl>
Link: https://patch.msgid.link/20260110114808.22595-1-floss@arusekk.pl
[nsc: Added comment about library order]
Signed-off-by: Nicolas Schier <nsc@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b58aac989 ]
Previously, the address of the shared member '&map->spinlock_flags' was
passed directly to 'hwspin_lock_timeout_irqsave'. This creates a race
condition where multiple contexts contending for the lock could overwrite
the shared flags variable, potentially corrupting the state for the
current lock owner.
Fix this by using a local stack variable 'flags' to store the IRQ state
temporarily.
Fixes: 8698b93647 ("regmap: Add hardware spinlock support")
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Link: https://patch.msgid.link/20260109032633.8732-1-eleanor.lin@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 383d4f5cff ]
The driver currently uses spi_alloc_host() to allocate the controller
but registers it using devm_spi_register_controller().
If devm_register_restart_handler() fails, the code jumps to the
put_ctlr label and calls spi_controller_put(). However, since the
controller was registered via a devm function, the device core will
automatically call spi_controller_put() again when the probe fails.
This results in a double-free of the spi_controller structure.
Fix this by switching to devm_spi_alloc_host() and removing the
manual spi_controller_put() call.
Fixes: ac17750 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Felix Gu <gu_0233@qq.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://patch.msgid.link/tencent_AC7D389CE7E24318445E226F7CDCCC2F0D07@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cc27f5c6d ]
The debugfs_create_str() API assumes that the string pointer is either NULL
or points to valid kmalloc() memory. Leaving the pointer uninitialized can
cause problems.
Initialize src_node and dst_node to empty strings before creating the
debugfs entries to guarantee that reads and writes are safe.
Fixes: 770c69f037 ("interconnect: Add debugfs test client")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Tested-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20260109122523.125843-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b39824ac4 ]
The probe() function ignored the return value of spi_setup(), leaving SPI
configuration failures undetected. If spi_setup() fails, the driver should
stop initialization and propagate the error to the caller.
Add proper error handling: check the return value of spi_setup() and return
it on failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2051f25d2a ("iio: adc: New driver for AD7280A Lithium Ion Battery Monitoring System")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c34e2e2d67 upstream.
The st_lsm6dsx_acc_channels array of struct iio_chan_spec has a non-NULL
event_spec field, indicating support for IIO events. However, event
detection is not supported for all sensors, and if userspace tries to
configure accelerometer wakeup events on a sensor device that does not
support them (e.g. LSM6DS0), st_lsm6dsx_write_event() dereferences a NULL
pointer when trying to write to the wakeup register.
Define an additional struct iio_chan_spec array whose members have a NULL
event_spec field, and use this array instead of st_lsm6dsx_acc_channels for
sensors without event detection capability.
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10dc959398 upstream.
Currently this is checked before running the pending work. Normally this
is quite fine, as work items either end up blocking (which will create a
new worker for other items), or they complete fairly quickly. But syzbot
reports an issue where io-wq takes seemingly forever to exit, and with a
bit of debugging, this turns out to be because it queues a bunch of big
(2GB - 4096b) reads with a /dev/msr* file. Since this file type doesn't
support ->read_iter(), loop_rw_iter() ends up handling them. Each read
returns 16MB of data read, which takes 20 (!!) seconds. With a bunch of
these pending, processing the whole chain can take a long time. Easily
longer than the syzbot uninterruptible sleep timeout of 140 seconds.
This then triggers a complaint off the io-wq exit path:
INFO: task syz.4.135:6326 blocked for more than 143 seconds.
Not tainted syzkaller #0
Blocked by coredump.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.135 state:D stack:26824 pid:6326 tgid:6324 ppid:5957 task_flags:0x400548 flags:0x00080000
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5256 [inline]
__schedule+0x1139/0x6150 kernel/sched/core.c:6863
__schedule_loop kernel/sched/core.c:6945 [inline]
schedule+0xe7/0x3a0 kernel/sched/core.c:6960
schedule_timeout+0x257/0x290 kernel/time/sleep_timeout.c:75
do_wait_for_common kernel/sched/completion.c:100 [inline]
__wait_for_common+0x2fc/0x4e0 kernel/sched/completion.c:121
io_wq_exit_workers io_uring/io-wq.c:1328 [inline]
io_wq_put_and_exit+0x271/0x8a0 io_uring/io-wq.c:1356
io_uring_clean_tctx+0x10d/0x190 io_uring/tctx.c:203
io_uring_cancel_generic+0x69c/0x9a0 io_uring/cancel.c:651
io_uring_files_cancel include/linux/io_uring.h:19 [inline]
do_exit+0x2ce/0x2bd0 kernel/exit.c:911
do_group_exit+0xd3/0x2a0 kernel/exit.c:1112
get_signal+0x2671/0x26d0 kernel/signal.c:3034
arch_do_signal_or_restart+0x8f/0x7e0 arch/x86/kernel/signal.c:337
__exit_to_user_mode_loop kernel/entry/common.c:41 [inline]
exit_to_user_mode_loop+0x8c/0x540 kernel/entry/common.c:75
__exit_to_user_mode_prepare include/linux/irq-entry-common.h:226 [inline]
syscall_exit_to_user_mode_prepare include/linux/irq-entry-common.h:256 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:159 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:194 [inline]
do_syscall_64+0x4ee/0xf80 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fa02738f749
RSP: 002b:00007fa0281ae0e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca
RAX: fffffffffffffe00 RBX: 00007fa0275e6098 RCX: 00007fa02738f749
RDX: 0000000000000000 RSI: 0000000000000080 RDI: 00007fa0275e6098
RBP: 00007fa0275e6090 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fa0275e6128 R14: 00007fff14e4fcb0 R15: 00007fff14e4fd98
There's really nothing wrong here, outside of processing these reads
will take a LONG time. However, we can speed up the exit by checking the
IO_WQ_BIT_EXIT inside the io_worker_handle_work() loop, as syzbot will
exit the ring after queueing up all of these reads. Then once the first
item is processed, io-wq will simply cancel the rest. That should avoid
syzbot running into this complaint again.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/68a2decc.050a0220.e29e5.0099.GAE@google.com/
Reported-by: syzbot+4eb282331cab6d5b6588@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8682d500f upstream.
PMD page table unsharing no longer touches the refcount of a PMD page
table. Also, it is not about dropping the refcount of a "PMD page" but
the "PMD page table".
Let's just simplify by saying that the PMD page table was unmapped,
consequently also unmapping the folio that was mapped into this page.
This code should be deduplicated in the future.
Link: https://lkml.kernel.org/r/20251223214037.580860-4-david@kernel.org
Fixes: 59d9094df3 ("mm: hugetlb: independent PMD page table shared count")
Signed-off-by: David Hildenbrand (Red Hat) <david@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Acked-by: Oscar Salvador <osalvador@suse.de>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: Harry Yoo <harry.yoo@oracle.com>
Cc: Lance Yang <lance.yang@linux.dev>
Cc: "Uschakow, Stanislav" <suschako@amazon.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25150715e0 upstream.
The GET_INSTANCE_ID macro that caused a kernel panic when accessing sysfs
attributes:
1. Off-by-one error: The loop condition used '<=' instead of '<',
causing access beyond array bounds. Since array indices are 0-based
and go from 0 to instances_count-1, the loop should use '<'.
2. Missing NULL check: The code dereferenced attr_name_kobj->name
without checking if attr_name_kobj was NULL, causing a null pointer
dereference in min_length_show() and other attribute show functions.
The panic occurred when fwupd tried to read BIOS configuration attributes:
Oops: general protection fault [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:min_length_show+0xcf/0x1d0 [hp_bioscfg]
Add a NULL check for attr_name_kobj before dereferencing and corrects
the loop boundary to match the pattern used elsewhere in the driver.
Cc: stable@vger.kernel.org
Fixes: 5f94f181ca ("platform/x86: hp-bioscfg: bioscfg-h")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20260115203725.828434-3-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
