When we are going to up interface to make connection, turn on BB and RF
hardware power by enable_bb_rf ops. Oppositely, using disable_bb_rf to
turn them off.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-3-pkshih@realtek.com
WiFi 7 chips can operate in various MLO applications, such as 1 link (2SS)
and 2 links (1SS + 1SS), and we should configure different PHY mode for
each of them.
For example,
- MLO_2_PLUS_0_1RF is 1 link with 2SS rate, and enable one RF component.
- MLO_1_PLUS_1_1RF is 2 links with 1SS rate for each, and enable one RF
component that can support two paths.
By default, we set the mode to legacy MLO_DBCC_NOT_SUPPORT (don't support
MLO and DBCC yet), and later we will introduce logic to change the mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240120003831.7014-2-pkshih@realtek.com
Currently it takes almost 6 seconds to upload the firmware for RTL8192CU
(and 11 seconds for RTL8192DU). That's because the firmware is uploaded
one byte at a time.
Also, after plugging the device, the firmware gets uploaded three times
before a connection to the AP is established.
Maybe this is fine for most users, but when testing changes to the
driver it's really annoying to wait so long.
Speed up the firmware upload by writing chunks of 64 bytes at a time.
This way it takes about 110 ms for RTL8192CU (and about 210 ms for
RTL8192DU).
PCI devices could upload it in chunks of 4 bytes, but I don't have any
to test and commit 89d32c9071 ("rtlwifi: Download firmware as bytes
rather than as dwords") decided otherwise anyway.
Allocate memory for the firmware image with kmalloc instead of vzalloc
because this memory is passed directly to usb_control_msg(), which
can't take memory allocated by vmalloc.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/d9bd4949-6e92-4f35-8b60-3b45f9ad74ab@gmail.com
Commit b837f78fbf ("wifi: rtl8xxxu: add hw crypto support for AP
mode") introduced max_sec_cam_num as a member of rtl8xxxu_fileops.
It was missed to set this number for all variants except 8188f, which
caused rtl8xxxu_get_free_sec_cam() to always return 0 and therefore breaking
encrypted traffic.
Fix it by adding the numbers for all variants. The values are taken from
the vendor drivers and rtlwifi.
Link: https://lore.kernel.org/linux-wireless/20240111163603.2325-1-zenmchen@gmail.com/
Fixes: b837f78fbf ("wifi: rtl8xxxu: add hw crypto support for AP mode")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240116095001.399500-1-martin.kaistra@linutronix.de
The firmware interface also defines events generated by
firmware on the device. As the get/set primitives the
events are likely to diverge between the vendors so this
commit adds support for per-vendor handling. The number
of events may differ so we let the vendor-specific code
allocate the struct brcmf_fweh_info which contains array
of event handlers. The existing event enumeration will be
used by the higher layers and thus are common definitions.
The vendor-specific code can provide a mapping table for
converting the common definition to the vendor-specific
firmware event definition and vice-versa.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240106103835.269149-4-arend.vanspriel@broadcom.com
When the brcmf_fwvid_attach() fails the driver instance is not added
to the vendor list. Hence we should not try to delete it from that
list when the brcmf_fwvid_detach() function is called in cleanup path.
Cc: stable@vger.kernel.org # 6.2.x
Fixes: d6a5c56221 ("wifi: brcmfmac: add support for vendor-specific firmware api")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240106103835.269149-3-arend.vanspriel@broadcom.com
People are getting spooked by brcmfmac errors on their boot console.
There's no reason for these messages to be errors.
Cc: stable@vger.kernel.org # 6.2.x
Fixes: d6a5c56221 ("wifi: brcmfmac: add support for vendor-specific firmware api")
Signed-off-by: Hector Martin <marcan@marcan.st>
[arend.vanspriel@broadcom.com: remove attach/detach vendor callbacks]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240106103835.269149-2-arend.vanspriel@broadcom.com
Using the WSEC command instead of sae_password seems to be the supported
mechanism on newer firmware, and also how the brcmdhd driver does it.
The existing firmware mechanism intended for (some) Cypress chips has
been separated from the new firmware mechanism using the multi-vendor
framework. Depending on the device it will select the appropriate
firmware mechanism.
This makes WPA3 work with iwd, or with wpa_supplicant pending a support
patchset [2].
[1] https://rachelbythebay.com/w/2023/11/06/wpa3/
[2] http://lists.infradead.org/pipermail/hostap/2023-July/041653.html
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Neal Gompa <neal@gompa.dev>
[arend.vanspriel@broadcom.com: use multi-vendor framework]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-5-arend.vanspriel@broadcom.com
The feature_disable option in brcmf_feat_attach() is a debugging or
workaround option to disable features that cause driver issues. Hence
they should be done as last step after all feature detection mechanisms
have been completed.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-4-arend.vanspriel@broadcom.com
Adding a .feat_attach() callback allowing per-vendor overrides
of the driver feature flags. In this patch the callback is only
provided by BCA vendor to disable SAE feature as it has not been
confirmed yet. BCA chips generally do not have the in-driver
supplicant (idsup) feature so they rely on NL80211_CMD_EXTERNAL_AUTH
to trigger user-space authentication.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-3-arend.vanspriel@broadcom.com
With multi-vendor support the vendor-specific module may need to use
the firmware interface functions so export them using the macro
BRCMF_EXPORT_SYMBOL_GPL() which exports them to driver namespace.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103095704.135651-2-arend.vanspriel@broadcom.com
This is the candidate patch of CVE-2023-47233 :
https://nvd.nist.gov/vuln/detail/CVE-2023-47233
In brcm80211 driver,it starts with the following invoking chain
to start init a timeout worker:
->brcmf_usb_probe
->brcmf_usb_probe_cb
->brcmf_attach
->brcmf_bus_started
->brcmf_cfg80211_attach
->wl_init_priv
->brcmf_init_escan
->INIT_WORK(&cfg->escan_timeout_work,
brcmf_cfg80211_escan_timeout_worker);
If we disconnect the USB by hotplug, it will call
brcmf_usb_disconnect to make cleanup. The invoking chain is :
brcmf_usb_disconnect
->brcmf_usb_disconnect_cb
->brcmf_detach
->brcmf_cfg80211_detach
->kfree(cfg);
While the timeout woker may still be running. This will cause
a use-after-free bug on cfg in brcmf_cfg80211_escan_timeout_worker.
Fix it by deleting the timer and canceling the worker in
brcmf_cfg80211_detach.
Fixes: e756af5b30 ("brcmfmac: add e-scan support.")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Cc: stable@vger.kernel.org
[arend.vanspriel@broadcom.com: keep timer delete as is and cancel work just before free]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240107072504.392713-1-arend.vanspriel@broadcom.com
In 'rt2x00crypto_rx_insert_iv()', added alignment can't exceed 3
bytes and ICV size is either 4 or 8 bytes, so skb space adjustment
may be simplified. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231019070750.17911-1-dmantipov@yandex.ru
debugfs_create_dir() returns ERR_PTR and never return NULL.
As Russell suggested, this patch removes the error checking for
debugfs_create_dir(). This is because the DebugFS kernel API is developed
in a way that the caller can safely ignore the errors that occur during
the creation of DebugFS nodes. The debugfs APIs have a IS_ERR() judge in
start_creating() which can handle it gracefully. So these checks are
unnecessary.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20230903030216.1509013-3-ruanjinjie@huawei.com
wlc_phy_txpwr_srom_read_nphy() in wlc_phy_attach_nphy() can not
return false, so it's impossible to get true value in this
if-statement. Also change those functions return types to void
since no one using it.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20230814093621.289754-1-artem.chernyshev@red-soft.ru
rtl8xxxu_limits and rtl8xxxu_combinations can be static const, so add
modifiers as desire. Otherwise, Sparse reports warnings
rtl8xxxu_core.c:7677:30: warning: symbol 'rtl8xxxu_limits' was not declared. Should it be static?
rtl8xxxu_core.c:7682:36: warning: symbol 'rtl8xxxu_combinations' was not declared. Should it be static?
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240116080945.20172-2-pkshih@realtek.com
Adding then removing a second vif currently makes the first vif not working
anymore. This is visible for example when we have a first interface
connected to some access point:
- create a wpa_supplicant.conf with some AP credentials
- wpa_supplicant -Dnl80211 -c /etc/wpa_supplicant.conf -i wlan0
- dhclient wlan0
- iw phy phy0 interface add wlan1 type managed
- iw dev wlan1 del
wlan0 does not manage properly traffic anymore (eg: ping not working)
This is due to vif mode being incorrectly reconfigured with some default
values in del_virtual_intf, affecting by default first vif.
Prevent first vif from being affected on second vif removal by removing vif
mode change command in del_virtual_intf
Fixes: 9bc061e880 ("staging: wilc1000: added support to dynamically add/remove interfaces")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-5-54d29463a738@bootlin.com
Use the correct register configuration when the WILC chip is down so the
successive interface up operation is successful. The modified registers
values during chip down helps to avoid the "FW not responding" debug
message which sometimes occurs because of temporary bus communication
failure during the next start. Also, make sure on first communication with
the chip that it is indeed woken up.
Reported-by: Michael Walle <mwalle@kernel.org>
Closes: https://lore.kernel.org/linux-wireless/20221026085415.6jgwrhq4sunqaypm@0002.3ffe.de/
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-4-54d29463a738@bootlin.com
Commit 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to
"NETDEV-wq"") moved workqueue creation in wilc_netdev_ifc_init in order to
set the interface name in the workqueue name. However, while the driver
needs only one workqueue, the wilc_netdev_ifc_init is called each time we
add an interface over a phy, which in turns overwrite the workqueue with a
new one. This can be observed with the following commands:
for i in $(seq 0 10)
do
iw phy phy0 interface add wlan1 type managed
iw dev wlan1 del
done
ps -eo pid,comm|grep wlan
39 kworker/R-wlan0
98 kworker/R-wlan1
102 kworker/R-wlan1
105 kworker/R-wlan1
108 kworker/R-wlan1
111 kworker/R-wlan1
114 kworker/R-wlan1
117 kworker/R-wlan1
120 kworker/R-wlan1
123 kworker/R-wlan1
126 kworker/R-wlan1
129 kworker/R-wlan1
Fix this leakage by putting back hif_workqueue allocation in
wilc_cfg80211_init. Regarding the workqueue name, it is indeed relevant to
set it lowercase, however it is not attached to a specific netdev, so
enforcing netdev name in the name is not so relevant. Still, enrich the
name with the wiphy name to make it clear which phy is using the workqueue.
Fixes: 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-3-54d29463a738@bootlin.com
During firmware initial configuration in wilc_init_fw_config, the special
driver_handler 0 should be used instead of targeting a specific virtual
interface (either 1 or 2)
The issue does not seem to have real consequence (both virtual interfaces
seems to answer correctly to a Add Block Ack request with the Immediate
policy), but lets make everything homogeneous
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-2-54d29463a738@bootlin.com
Instead of reading bit 9 of RFPGA0_XA_HSSIPARAMETER2 every time a frame
is received, just use rtlphy->cck_high_power, which is initialised in
_rtl92d_phy_bb_config(). That bit never changes anyway.
With this change _rtl92de_query_rxphystatus() can be shared with the
upcoming USB driver. The USB driver can't read registers in this
function because register reading can sleep.
Compile tested only.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/19a3e023-0eaa-4096-9f78-a2c8e909cb54@gmail.com
WiFi 7 chips will support MLD, so there are more fields about that. But
currently we don't support MLD yet, just define fields and bits by this
patch ahead, and fill STA_TYPE only.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-9-pkshih@realtek.com
The JOIN command is used to tell firmware an new station is joining, and
create an entry for it. This patch is only to convert to set data via
struct, and don't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-8-pkshih@realtek.com
Reset DMAC table, so we get expected behavior instead of random values at
early stage.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-7-pkshih@realtek.com
Do reset on CMAC tables by mac_id, so we don't get random values when
powering on. Therefore, add the same function for WiFi 7 chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-6-pkshih@realtek.com
The CMAC table is used to define how hardware TX a certain packet, and
we can specify TX AMPDU size, so hardware can prepare proper retry window
buffer. Otherwise, it can't transmit with expected aggregation number.
Since each TID could have different aggregation number, the smallest number
is adopted to prevent over peer's receiving buffer.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-5-pkshih@realtek.com
For WiFi 7 chips, we add H2C command with rich fields to support MLO, so
add a chip_ops to generalize calling of update CMAC table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-4-pkshih@realtek.com
When a station get connected, fill hardware CMAC table via H2C command to
tell hardware arguments related to transmit, such as the lowest rate,
packet padding and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-3-pkshih@realtek.com
To have secure connection, set key information into security CAM including
key index, entry index and valid map. This new introduced H2C command can
support MLO, but currently not implement yet.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115033742.16372-2-pkshih@realtek.com
According to IEEE Std. 802.11, it defines:
Indicates whether the STA is capable of interpreting the Extended NSS BW
Support subfield of the VHT Capabilities Information field.
Some AP such as TP-LINK BE19000 would check it for bandwidth settings, so
causes 80MHz rate when associating on 160 MHz bandwidth. Declare this
capability to yield expected result.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240112062640.36922-5-pkshih@realtek.com
The coming WiFi 7 chip 8922A will support EHT, so declare EHT along with
hardware capabilities.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240112062640.36922-4-pkshih@realtek.com
Basically, all chips can support 20/40/80MHz bandwidth, and 8952C can
support 160MHz bandwidth, which is why we introduced support_bw160 before.
The coming WiFi 7 chips will support 320MHz optionally, so change it to
bit mask instead of adding another support_bw320.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240112062640.36922-3-pkshih@realtek.com
EHT capabilities are also stored in struct ieee80211_sband_iftype_data, so
adjust allocation of iftype_data as common part named init_he_eht_cap(),
and then init_eht_cap() can be added later. Don't change logic at all
by this patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240112062640.36922-2-pkshih@realtek.com
When 'sscanf()' is not needed to scan an input, prefer common
'kstrtoX_from_user()' over 'rtw_debugfs_copy_from_user()' with
following 'kstrtoX()'. Minor adjustments, compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240110132930.438828-1-dmantipov@yandex.ru
The CSA countdown in the beacon frames, which are sent out by firmware,
needs to get updated by the driver. To achieve this, convert
update_beacon_work to delayed_work and schedule it with the beacon
interval in case CSA is active and the countdown is not complete.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240111163628.320697-3-martin.kaistra@linutronix.de
The workqueue might still be running, when the driver is stopped. To
avoid a use-after-free, call cancel_work_sync() in rtl8xxxu_stop().
Fixes: e542e66b7c ("rtl8xxxu: add bluetooth co-existence support for single antenna")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240111163628.320697-2-martin.kaistra@linutronix.de
Currently rtl_usb performs register writes using the async
usb_submit_urb() function. This appears to work fine for the RTL8192CU,
but the RTL8192DU (soon to be supported by rtlwifi) has a problem:
it transmits everything at the 1M rate in the 2.4 GHz band. (The 5 GHz
band is still untested.)
With this patch, rtl_usb performs the register writes using the
synchronous usb_control_msg() function, and the RTL8192DU works
normally. The RTL8192CU still works.
The vendor drivers use the async writes in only one function,
rtl8192du_trigger_gpio_0 / rtl8192cu_trigger_gpio_0, which probably
doesn't even run in real life. They use sync writes everywhere else.
Also, remove "sync" and "async" from the names of the members of
struct rtl_io to avoid confusion:
write{8,16,32}_async -> write{8,16,32}
read{8,16,32}_sync -> read{8,16,32}
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/fb71bae6-8b19-4b6e-b4a6-0d260f2139e1@gmail.com
Remove unreachable branches in 'rtl92ce_tx_fill_desc()',
'rtl92cu_tx_fill_desc()' and 'rtl8723e_tx_fill_desc()'.
Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240109104735.140550-1-dmantipov@yandex.ru
Since coming WiFi 7 and existing chips use different update_beacon()
format, add to abstract selection of H2C command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091359.67636-1-pkshih@realtek.com
The firmware of coming WiFi 7 chips can support more AP functions, like
virtual AP, so extend format of download beacon frame to configure them.
Currently rtw89 only enables AP mode as old chips, so leave new fields
zeros.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091333.67484-1-pkshih@realtek.com
Download beacon frame via H2C command for AP mode, and then firmware can
issues beacon periodically. Originally TIM offset minus fixed 24 bytes of
frame header implicitly in macro, and this patch explicitly uses
ieee80211_hdrlen() to get header length, but expected to change nothing
at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091325.67424-1-pkshih@realtek.com
New H2C command is introduced to pause/sleep transmitting. That extends
more bits to support more MAC ID, and currently we still configure 256
MAC ID at most.
This new command is always used by coming WiFi 7 chips, and existing
chips can use old or new command because firmware still preserves the old
one. Add a firmware feature flag to determine which command is adopted
according to firmware version.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091315.67358-1-pkshih@realtek.com
To reuse this function to support extended H2C command that is used by
newer chip, change to use a pointer to fill pause ID and mask.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091307.67296-1-pkshih@realtek.com
The WiFi 6 chips use these commands to create BA CAM entry when RX BA
session is established, this BA CAM can record whether packets are received
or not, then reply BA for current status. This patch doesn't change logic.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091245.67220-1-pkshih@realtek.com
The total BA CAM number of 8922a is 32 instead of 16, and initial 8
entries are dynamic, so update the entry number to 24.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-5-pkshih@realtek.com
Since chips could use different version of BA CAM H2C command, add a
chip_ops to abstract the operation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-4-pkshih@realtek.com
Add a call of feature_init() when bringing interface up. For now, the
feature is to reset BA CAM V1 that is only used by upcoming 8922A.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-3-pkshih@realtek.com
BA CAM is used to generate BA frame for received AMPDU packets. To support
WiFi 7, change format from V0 to have more fields and enlarge entry number
for new need.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240108091134.67007-2-pkshih@realtek.com
