[ Upstream commit af4044fd0b ]
When gfs2_create_inode() finds a directory, make sure to return -EISDIR.
Fixes: 571a4b5797 ("GFS2: bugger off early if O_CREAT open finds a directory")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae9f3bd825 ]
Currently, sdp->sd_aspace and the per-inode metadata address spaces use
sb->s_bdev->bd_mapping->host as their ->host; folios in those address
spaces will thus appear to be on bdev rather than on gfs2 filesystems.
This is a problem because gfs2 doesn't support cgroup writeback
(SB_I_CGROUPWB), but bdev does.
Fix that by using a "dummy" gfs2 inode as ->host in those address
spaces. When coming from a folio, folio->mapping->host->i_sb will then
be a gfs2 super block and the SB_I_CGROUPWB flag will not be set in
sb->s_iflags.
Based on a previous version from Bob Peterson from several years ago.
Thanks to Tetsuo Handa, Jan Kara, and Rafael Aquini for helping figure
this out.
Fixes: aaa2cacf81 ("writeback: add lockdep annotation to inode_to_wb()")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2492e5aba2 ]
Unlike L3 and DF counters, UMC counters (PERF_CTRs) set the Overflow bit
(bit 48) and saturate on overflow. A subsequent pmu->read() of the event
reports an incorrect accumulated count as there is no difference between
the previous and the current values of the counter.
To avoid this, inspect the current counter value and proactively reset
the corresponding PERF_CTR register on every pmu->read(). Combined with
the periodic reads initiated by the hrtimer, the counters never get a
chance saturate but the resolution reduces to 47 bits.
Fixes: 25e5684782 ("perf/x86/amd/uncore: Add memory controller support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Song Liu <song@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/dee9c8af2c6d66814cf4c6224529c144c620cf2c.1744906694.git.sandipan.das@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8feb053d53 ]
Gabriele noted that in case of signal_pending_state(), the tracepoint
sees a stale task-state.
Fixes: fa2c3254d7 ("sched/tracing: Don't re-read p->state when emitting sched_switch event")
Reported-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Valentin Schneider <vschneid@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea4dd134ef ]
Rework error handling in sun8i_ce_hash_run() to unmap the dma buffers in
case of failure. Currently, the dma unmap functions are not called if the
function errors out at various points.
Fixes: 56f6d5aee8 ("crypto: sun8i-ce - support hash algorithms")
Signed-off-by: Ovidiu Panait <ovidiu.panait.oss@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f13c60d84 ]
The following commit, 12 years ago:
7e98b71920 ("x86, idle: Use static_cpu_has() for CLFLUSH workaround, add barriers")
added barriers around the CLFLUSH in mwait_idle_with_hints(), justified with:
... and add memory barriers around it since the documentation is explicit
that CLFLUSH is only ordered with respect to MFENCE.
This also triggered, 11 years ago, the same adjustment in:
f8e617f458 ("sched/idle/x86: Optimize unnecessary mwait_idle() resched IPIs")
during development, although it failed to get the static_cpu_has_bug() treatment.
X86_BUG_CLFLUSH_MONITOR (a.k.a the AAI65 errata) is specific to Intel CPUs,
and the SDM currently states:
Executions of the CLFLUSH instruction are ordered with respect to each
other and with respect to writes, locked read-modify-write instructions,
and fence instructions[1].
With footnote 1 reading:
Earlier versions of this manual specified that executions of the CLFLUSH
instruction were ordered only by the MFENCE instruction. All processors
implementing the CLFLUSH instruction also order it relative to the other
operations enumerated above.
i.e. The SDM was incorrect at the time, and barriers should not have been
inserted. Double checking the original AAI65 errata (not available from
intel.com any more) shows no mention of barriers either.
Note: If this were a general codepath, the MFENCEs would be needed, because
AMD CPUs of the same vintage do sport otherwise-unordered CLFLUSHs.
Remove the unnecessary barriers. Furthermore, use a plain alternative(),
rather than static_cpu_has_bug() and/or no optimisation. The workaround
is a single instruction.
Use an explicit %rax pointer rather than a general memory operand, because
MONITOR takes the pointer implicitly in the same way.
[ mingo: Cleaned up the commit a bit. ]
Fixes: 7e98b71920 ("x86, idle: Use static_cpu_has() for CLFLUSH workaround, add barriers")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250402172458.1378112-1-andrew.cooper3@citrix.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 116edfe173 ]
Error handling in kcpuid is unreliable. On malloc() failures, the code
prints an error then just goes on. The error messages are also printed
to standard output instead of standard error.
Use err() and errx() from <err.h> to direct all error messages to
standard error and automatically exit the program. Use err() to include
the errno information, and errx() otherwise. Use warnx() for warnings.
While at it, alphabetically reorder the header includes.
[ mingo: Fix capitalization in the help text while at it. ]
Fixes: c6b2f240bf ("tools/x86: Add a kcpuid tool to show raw CPU features")
Reported-by: Remington Brasga <rbrasga@uci.edu>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20250324142042.29010-2-darwi@linutronix.de
Closes: https://lkml.kernel.org/r/20240926223557.2048-1-rbrasga@uci.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b824eef26 upstream.
This reverts commit cfb2d41831 since it
causes regressions on certain configs. Revert until the issue can be
isolated and debugged.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4238
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b3a91b207 upstream.
The ticket TKT0676370 shows the description of TX_VBOOST_LVL is wrong in
register PHY_CTRL3 bit[31:29].
011: Corresponds to a launch amplitude of 1.12 V.
010: Corresponds to a launch amplitude of 1.04 V.
000: Corresponds to a launch amplitude of 0.88 V.
After updated:
011: Corresponds to a launch amplitude of 0.844 V.
100: Corresponds to a launch amplitude of 1.008 V.
101: Corresponds to a launch amplitude of 1.156 V.
This will correct it accordingly.
Fixes: b2e75563dc ("dt-bindings: phy: imx8mq-usb: add phy tuning properties")
Cc: stable@vger.kernel.org
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250430094502.2723983-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ad4b5a7de upstream.
The Cypress HX3 hubs use different default PID value depending
on the variant. Update compatibles list.
Becasuse all hub variants use the same driver data, allow the
dt node to have two compatibles: leftmost which matches the HW
exactly, and the second one as fallback.
Fixes: 1eca51f58a ("dt-bindings: usb: Add binding for Cypress HX3 USB 3.0 family")
Cc: stable@vger.kernel.org # 6.6
Cc: stable@vger.kernel.org # Backport of the patch ("dt-bindings: usb: usb-device: relax compatible pattern to a contains") from list: https://lore.kernel.org/linux-usb/20250418-dt-binding-usb-device-compatibles-v2-1-b3029f14e800@cherry.de/
Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-2-4a76a474a010@thaumatec.com
[taken with Greg's blessing]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f73628e9d upstream.
Some of our devices crash in tb_cfg_request_dequeue():
general protection fault, probably for non-canonical address 0xdead000000000122
CPU: 6 PID: 91007 Comm: kworker/6:2 Tainted: G U W 6.6.65
RIP: 0010:tb_cfg_request_dequeue+0x2d/0xa0
Call Trace:
<TASK>
? tb_cfg_request_dequeue+0x2d/0xa0
tb_cfg_request_work+0x33/0x80
worker_thread+0x386/0x8f0
kthread+0xed/0x110
ret_from_fork+0x38/0x50
ret_from_fork_asm+0x1b/0x30
The circumstances are unclear, however, the theory is that
tb_cfg_request_work() can be scheduled twice for a request:
first time via frame.callback from ring_work() and second
time from tb_cfg_request(). Both times kworkers will execute
tb_cfg_request_dequeue(), which results in double list_del()
from the ctl->request_queue (the list poison deference hints
at it: 0xdead000000000122).
Do not dequeue requests that don't have TB_CFG_REQUEST_ACTIVE
bit set.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342e4955a1 upstream.
wait_event_interruptible_timeout requires a timeout argument
in units of jiffies. It was being called in usbtmc_get_stb
with the usb timeout value which is in units of milliseconds.
Pass the timeout argument converted to jiffies.
Fixes: 048c6d88a0 ("usb: usbtmc: Add ioctls to set/get usb timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb410c914 upstream.
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4239ace2d upstream.
debugfs.c emits the following warnings when compiling with the -Wsign-conversion flag with clang 15:
drivers/usb/typec/ucsi/debugfs.c:58:27: warning: implicit conversion changes signedness: 'int' to 'u32' (aka 'unsigned int') [-Wsign-conversion]
ucsi->debugfs->status = ret;
~ ^~~
drivers/usb/typec/ucsi/debugfs.c:71:25: warning: implicit conversion changes signedness: 'u32' (aka 'unsigned int') to 'int' [-Wsign-conversion]
return ucsi->debugfs->status;
~~~~~~ ~~~~~~~~~~~~~~~^~~~~~
During ucsi_cmd() we see:
if (ret < 0) {
ucsi->debugfs->status = ret;
return ret;
}
But "status" is u32 meaning unsigned wrap-around occurs when assigning a value which is < 0 to it, this obscures the real status.
To fix this make the "status" of type int since ret is also of type int.
Fixes: df0383ffad ("usb: typec: ucsi: Add debugfs for ucsi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250422134717.66218-1-qasdev00@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a889482b upstream.
Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN).
Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN).
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f7955919 upstream.
This device exhibits I/O errors during file transfers due to unstable
link power management (LPM) behavior. The kernel logs show repeated
warm resets and eventual disconnection when LPM is enabled:
[ 3467.810740] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0020
[ 3467.810740] usb usb2-port5: do warm reset
[ 3467.866444] usb usb2-port5: not warm reset yet, waiting 50ms
[ 3467.907407] sd 0:0:0:0: [sda] tag#12 sense submit err -19
[ 3467.994423] usb usb2-port5: status 02c0, change 0001, 10.0 Gb/s
[ 3467.994453] usb 2-5: USB disconnect, device number 4
The error -19 (ENODEV) occurs when the device disappears during write
operations. Adding USB_QUIRK_NO_LPM disables link power management
for this specific device, resolving the stability issues.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250508055947.764538-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d95fdee225 which is
upstream commit be4ae8c194.
This commit is causing a suspend regression on Tegra186 Jetson TX2 with
Linux v6.12.y kernels. This is not seen with Linux v6.15 that includes
this change but indicates that there are there changes missing.
Therefore, revert this change.
Fixes: d95fdee225 ("cpufreq: tegra186: Share policy per cluster")
Link: https://lore.kernel.org/linux-tegra/bf1dabf7-0337-40e9-8b8e-4e93a0ffd4cc@nvidia.com/
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26064d3e2b upstream.
>4GB folio is possible on some ARCHs, such as aarch64, 16GB hugepage
is supported, then 'offset' of folio can't be held in 'unsigned int',
cause warning in bio_add_folio_nofail() and IO failure.
Fix it by adjusting 'page' & trimming 'offset' so that `->bi_offset` won't
be overflow, and folio can be added to bio successfully.
Fixes: ed9832bc08 ("block: introduce folio awareness and add a bigger size from folio")
Cc: Kundan Kumar <kundan.kumar@samsung.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Gavin Shan <gshan@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20250312145136.2891229-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[ The follow-up fix fbecd731de ("xfs: fix zoned GC data corruption due to
wrong bv_offset") addresses issues in the file fs/xfs/xfs_zone_gc.c. This
file was first introduced in version v6.15-rc1. So don't backport the follow
up fix to 6.12.y. ]
Signed-off-by: Alva Lan <alvalan9@foxmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7447990137 upstream.
PCIe r6.2, sec 5.5.4, requires that:
If setting either or both of the enable bits for ASPM L1 PM Substates,
both ports must be configured as described in this section while ASPM L1
is disabled.
Previously, pcie_config_aspm_l1ss() assumed that "setting enable bits"
meant "setting them to 1", and it configured L1SS as follows:
- Clear L1SS enable bits
- Disable L1
- Configure L1SS enable bits as required
- Enable L1 if required
With this sequence, when disabling L1SS on an ARM A-core with a Synopsys
DesignWare PCIe core, the CPU occasionally hangs when reading
PCI_L1SS_CTL1, leading to a reboot when the CPU watchdog expires.
Move the L1 disable to the caller (pcie_config_aspm_link(), where L1 was
already enabled) so L1 is always disabled while updating the L1SS bits:
- Disable L1
- Clear L1SS enable bits
- Configure L1SS enable bits as required
- Enable L1 if required
Change pcie_aspm_cap_init() similarly.
Link: https://lore.kernel.org/r/20241007032917.872262-1-ajayagarwal@google.com
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
[bhelgaas: comments, commit log, compute L1SS setting before config access]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Johnny-CC Chang <Johnny-CC.Chang@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88bdd1644c upstream.
Apply Hardware Architecture Specification compatible delays
for main island power delivery for 50xx and above.
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241004162505.1695605-3-maciej.falkowski@linux.intel.com
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c140244f0c upstream.
Add support for the 5th generation of Intel NPU that
is going to be present in PTL_P (Panther Lake) CPUs.
NPU5 code reuses almost all of previous driver code.
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241004162505.1695605-2-maciej.falkowski@linux.intel.com
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe9f5f96cf upstream.
The comparison
rtc->start_secs > rtc->range_max
has a signed left-hand side and an unsigned right-hand side.
So the comparison might become true for negative start_secs which is
interpreted as a (possibly very large) positive value.
As a negative value can never be bigger than an unsigned value
the correct representation of the (mathematical) comparison
rtc->start_secs > rtc->range_max
in C is:
rtc->start_secs >= 0 && rtc->start_secs > rtc->range_max
Use that to fix the offset calculation currently used in the
rtc-mt6397 driver.
Fixes: 989515647e ("rtc: Add one offset seconds to expand RTC range")
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250428-enable-rtc-v4-2-2b2f7e3f9349@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7df4cfef8b upstream.
Conversion of dates before 1970 is still relevant today because these
dates are reused on some hardwares to store dates bigger than the
maximal date that is representable in the device's native format.
This prominently and very soon affects the hardware covered by the
rtc-mt6397 driver that can only natively store dates in the interval
1900-01-01 up to 2027-12-31. So to store the date 2028-01-01 00:00:00
to such a device, rtc_time64_to_tm() must do the right thing for
time=-2208988800.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250428-enable-rtc-v4-1-2b2f7e3f9349@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6db0261f37 upstream.
Document that references to data nodes shall use string-only references
instead of a device reference and a succession of the first package
entries of hierarchical data node references.
Fixes: 9880702d12 ("ACPI: property: Support using strings in reference properties")
Cc: 6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://patch.msgid.link/20250409084738.3657079-1-sakari.ailus@linux.intel.com
[ rjw: Clarifying edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb6a85f38f upstream.
commit 0834667545 ("cpufreq: ACPI: Fix max-frequency computation")
modified get_max_boost_ratio() to return the nominal_freq advertised
in the _CPC object. This was for the purposes of computing the maximum
frequency. The frequencies advertised in _CPC objects are in
MHz. However, cpufreq expects the frequency to be in KHz. Since the
nominal_freq returned by get_max_boost_ratio() was not in KHz but
instead in MHz,the cpuinfo_max_frequency that was computed using this
nominal_freq was incorrect and an invalid value which resulted in
cpufreq reporting the P0 frequency as the cpuinfo_max_freq.
Fix this by converting the nominal_freq to KHz before returning the
same from get_max_boost_ratio().
Reported-by: Manu Bretelle <chantr4@gmail.com>
Closes: https://lore.kernel.org/lkml/aDaB63tDvbdcV0cg@HQ-GR2X1W2P57/
Fixes: 0834667545 ("cpufreq: ACPI: Fix max-frequency computation")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Cc: 6.14+ <stable@vger.kernel.org> # 6.14+
Link: https://patch.msgid.link/20250529085143.709-1-gautham.shenoy@amd.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6ebd49429 upstream.
Changing the direction before updating the output value in the
OUTPUT_VAL register may result in a glitch on the output line
if the previous value in the OUTPUT_VAL register is different
from the one we want to set.
In order to avoid that, update the output value before changing
the direction.
Cc: stable@vger.kernel.org
Fixes: 6702abb3bf ("pinctrl: armada-37xx: Fix direction_output() callback behavior")
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/20250514-pinctrl-a37xx-fixes-v2-2-07e9ac1ab737@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 947c93eb29 upstream.
The controller has two consecutive OUTPUT_VAL registers and both
holds output value for 32 GPIOs. Due to a missing adjustment, the
current code always uses the first register while setting the
output value whereas it should use the second one for GPIOs > 31.
Add the missing armada_37xx_update_reg() call to adjust the register
according to the 'offset' parameter of the function to fix the issue.
Cc: stable@vger.kernel.org
Fixes: 6702abb3bf ("pinctrl: armada-37xx: Fix direction_output() callback behavior")
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/20250514-pinctrl-a37xx-fixes-v2-1-07e9ac1ab737@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fbdb6d8e0 upstream.
On arm32, size_t is defined to be unsigned int, while PAGE_SIZE is
unsigned long. This hence triggers a compilation warning as min()
asserts the type of two operands to be equal. Casting PAGE_SIZE to size_t
solves this issue and works on other target architectures as well.
Compilation warning details:
kernel/trace/trace.c: In function 'tracing_splice_read_pipe':
./include/linux/minmax.h:20:28: warning: comparison of distinct pointer types lacks a cast
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
^
./include/linux/minmax.h:26:4: note: in expansion of macro '__typecheck'
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~
...
kernel/trace/trace.c:6771:8: note: in expansion of macro 'min'
min((size_t)trace_seq_used(&iter->seq),
^~~
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250526013731.1198030-1-pantaixi@huaweicloud.com
Fixes: f5178c41bb ("tracing: Fix oob write in trace_seq_to_buffer()")
Reviewed-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Pan Taixi <pantaixi@huaweicloud.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10379171f3 ]
The list_first_entry() macro never returns NULL. If the list is
empty then it returns an invalid pointer. Use list_first_entry_or_null()
to check if the list is empty.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202505080231.7OXwq4Te-lkp@intel.com/
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50980d8da7 ]
Using random mac address is not an error since the driver continues to
function, it should be informative that the system has not assigned
a MAC address. This is inline with other drivers such as ax88796c,
dm9051 etc. Drop the error level to info level.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250516122655.442808-1-nm@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad8a4ddc4 ]
This board need to shutdown Class-D amp to avoid EMI issue.
Restore the Auto-Mute mode item will off pin control when Auto-mute mode was enable.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Links: https://lore.kernel.org/ee8bbe5236464c369719d96269ba8ef8@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e255ff9f ]
The S2110 has an additional set of media playback control keys enabled
by a hardware toggle button that switches the keys between "Application"
and "Player" modes. Toggling "Player" mode just shifts the scancode of
each hotkey up by 4.
Add defines for new scancodes, and a keymap and dmi id for the S2110.
Tested on a Fujitsu Lifebook S2110.
Signed-off-by: Valtteri Koskivuori <vkoskiv@gmail.com>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Link: https://lore.kernel.org/r/20250509184251.713003-1-vkoskiv@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcd21b609d ]
The Linux client assumes that all filehandles are non-volatile for
renames within the same directory (otherwise sillyrename cannot work).
However, the existence of the Linux 'subtree_check' export option has
meant that nfs_rename() has always assumed it needs to flush writes
before attempting to rename.
Since NFSv4 does allow the client to query whether or not the server
exhibits this behaviour, and since knfsd does actually set the
appropriate flag when 'subtree_check' is enabled on an export, it
should be OK to optimise away the write flushing behaviour in the cases
where it is clearly not needed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32d495b384 ]
Fix Smatch-detected issue:
drivers/char/tpm/tpm-buf.c:208 tpm_buf_read_u8() error:
uninitialized symbol 'value'.
drivers/char/tpm/tpm-buf.c:225 tpm_buf_read_u16() error:
uninitialized symbol 'value'.
drivers/char/tpm/tpm-buf.c:242 tpm_buf_read_u32() error:
uninitialized symbol 'value'.
Zero-initialize the return values in tpm_buf_read_u8(), tpm_buf_read_u16(),
and tpm_buf_read_u32() to guard against uninitialized data in case of a
boundary overflow.
Add defensive initialization ensures the return values are always defined,
preventing undefined behavior if the unexpected happens.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce15563e49 ]
Save the gt pointer in the lrc so that it can used for gt based helpers.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250509161159.2173069-7-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 741d3ef8b8)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1f704107c ]
Add Wa_22021007897 for the Xe2_HPG (graphics version: 20.01) IP. It is
a permanent workaround, and applicable on all the steppings.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@intel.com>
Link: https://lore.kernel.org/r/20250512065004.2576-1-aradhya.bhatia@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit e5c13e2c50)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e765bf89f4 ]
This commit adds the NVME_QUIRK_NO_DEEPEST_PS quirk for device
[126f:2262], which belongs to device SOLIDIGM P44 Pro SSDPFKKW020X7
The device frequently have trouble exiting the deepest power state (5),
resulting in the entire disk being unresponsive.
Verified by setting nvme_core.default_ps_max_latency_us=10000 and
observing the expected behavior.
Signed-off-by: Ilya Guterman <amfernusus@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb98bd0a13 ]
The SPI interface is activated before the CPOL setting is applied. In
that moment, the clock idles high and CS goes low. After a short delay,
CPOL and other settings are applied, which may cause the clock to change
state and idle low. This transition is not part of a clock cycle, and it
can confuse the receiving device.
To prevent this unexpected transition, activate the interface while CPOL
and the other settings are being applied.
Signed-off-by: Alessandro Grassi <alessandro.grassi@mailbox.org>
Link: https://patch.msgid.link/20250502095520.13825-1-alessandro.grassi@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9475055b1 ]
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.
In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f097adb9b ]
JH7110 USB 2.0 host fails to detect USB 2.0 devices occasionally. With a
long time of debugging and testing, we found that setting Rx clock gating
control signal to normal power consumption mode can solve this problem.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20250422101244.51686-1-hal.feng@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c1a467372 ]
[Why & How]
When MST config is unplugged/replugged too quickly, it can potentially
result in a scenario where previous DC state has not been reset before
the HPD link detection sequence begins. In this case, driver will
disable the streams/link prior to re-enabling the link for link
training.
There is a bug in the current logic that does not account for the fact
that current_state can be released and cleared prior to swapping to a
new state (resulting in the pipe_ctx stream pointers to be cleared) in
between disabling streams.
To resolve this, cache the original streams prior to committing any
stream updates.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1561782686)
Signed-off-by: Sasha Levin <sashal@kernel.org>
