Use RUNTIME_PM_OPS() instead of the old SET_SYSTEM_SLEEP_PM_OPS().
This means we don't need __maybe_unused on the functions.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-2-raphael.gallais-pou@foss.st.com
The Low-Voltage Differential Signaling (LVDS) Display Interface
Transmitter handles the LVDS protocol: it maps the pixels received from
the upstream Pixel-DMA LCD-TFT Display Controller (LTDC) onto the LVDS
PHY.
It is composed of three sub blocks:
* LVDS host: handles the LVDS protocol (FPD / OpenLDI) and maps
its input pixels onto the data lanes of the PHY
* LVDS PHY: parallelize the data and drives the LVDS data lanes
* LVDS wrapper: handles top-level settings
The LVDS controller driver supports the following high-level features:
* FDP-Link-I and OpenLDI (v0.95) protocols
* Single-Link or Dual-Link operation
* Single-Display or Double-Display (with the same content
duplicated on both)
* Flexible Bit-Mapping, including JEIDA and VESA
* RGB888 or RGB666 output
* Synchronous design, with one input pixel per clock cycle
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226-lvds-v6-2-15e3463fbe70@foss.st.com
Currently, the init_code of the jd9365da driver is placed
in the enable() function and sent, but this seems to take
a long time. It takes 17ms to send each instruction (an init
code consists of about 200 instructions), so it takes
about 3.5s to send the init_code. So we moved the sending
of the inti_code to the prepare() function, and each
instruction seemed to take only 25μs.
We checked the DSI host and found that the difference in
command sending time is caused by the different modes of
the DSI host in prepare() and enable() functions.
Our DSI Host only supports sending cmd in LP mode, The
prepare() function can directly send init_code (LP->cmd)
in LP mode, but the enable() function is in HS mode and
needs to switch to LP mode before sending init code
(HS->LP->cmd->HS). Therefore, it takes longer to send
the command.
Signed-off-by: Zhaoxiong Lv <lvzhaoxiong@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240624141926.5250-2-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624141926.5250-2-lvzhaoxiong@huaqin.corp-partner.google.com
Commit 78464d7681 ("tools/power turbostat: Add columns for clustered
uncore frequency") introduced 'probe_intel_uncore_frequency_cluster()'
in a way which prevents printing uncore frequency columns if either of
the '-q' or '-l' options are used. Systems which do not have multiple
uncore frequencies per package are unaffected by this regression.
Fix the function so that uncore frequency columns are shown when either
the '-l' or '-q' option is used by checking if 'quiet' is true after
adding counters for the uncore frequency columns.
Fixes: 78464d7681 ("tools/power turbostat: Add columns for clustered uncore frequency")
Signed-off-by: Adam Hawley <adam.james.hawley@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In some cases specifying the '-n' command line argument will cause
turbostat to fail. For instance 'turbostat -n 1' works fine; however,
'turbostat -n 1 -d' will fail. This is the result of the first call
to getopt_long_only() where "MP" is specified as the optstring. This can
be easily fixed by changing the optstring from "MP" to "MPn:" to remove
ambiguity between the arguments.
tools/power turbostat: option '-n' is ambiguous; possibilities: '-num_iterations' '-no-msr' '-no-perf'
Fixes: a0e86c90b8 ("tools/power turbostat: Add --no-perf option")
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
core:
- fix refcounting race on pid handover
fbdev:
- Fix fb_info when vmalloc is used, regression from
CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM.
amdgpu:
- SMU 14.x fix
- vram info parsing fix
- mode1 reset fix
- LTTPR fix
- Virtual display fix
- Avoid spurious error in PSP init
i915:
- Fix potential UAF due to race on fence register revocation
nouveau
- nouveau tv mode fixes.
panel:
- Add KOE TX26D202VM0BWA timings.
-----BEGIN PGP SIGNATURE-----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=0isZ
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2024-06-28' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Regular fixes, mostly amdgpu with some minor fixes in other places,
along with a fix for a very narrow UAF race in the pid handover code.
core:
- fix refcounting race on pid handover
fbdev:
- Fix fb_info when vmalloc is used, regression from
CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM.
amdgpu:
- SMU 14.x fix
- vram info parsing fix
- mode1 reset fix
- LTTPR fix
- Virtual display fix
- Avoid spurious error in PSP init
i915:
- Fix potential UAF due to race on fence register revocation
nouveau
- nouveau tv mode fixes
panel:
- Add KOE TX26D202VM0BWA timings"
* tag 'drm-fixes-2024-06-28' of https://gitlab.freedesktop.org/drm/kernel:
drm/drm_file: Fix pid refcounting race
drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_hd_modes
drm/amdgpu: Don't show false warning for reg list
drm/amdgpu: avoid using null object of framebuffer
drm/amd/display: Send DP_TOTAL_LTTPR_CNT during detection if LTTPR is present
drm/amdgpu: Fix pci state save during mode-1 reset
drm/amdgpu/atomfirmware: fix parsing of vram_info
drm/amd/swsmu: add MALL init support workaround for smu_v14_0_1
drm/i915/gt: Fix potential UAF by revoke of fence registers
drm/panel: simple: Add missing display timing flags for KOE TX26D202VM0BWA
drm/fbdev-dma: Only set smem_start is enable per module option
This tag contains habanalabs driver changes for v6.11.
The notable changes are:
- uAPI changes:
- Use device-name directory in debugfs-driver-habanalabs.
- Expose server type in debugfs.
- New features and improvements:
- Gradual sleep in polling memory macro.
- Reduce Gaudi2 MSI-X interrupt count to 128.
- Add Gaudi2-D revision support.
- Firmware related changes:
- Add timestamp to CPLD info.
- Gaudi2: Assume hard-reset by firmware upon MC SEI severe error.
- Align Gaudi2 interrupt names.
- Check for errors after preboot is ready.
- Bug fixes and code cleanups:
- Move heartbeat work initialization to early init.
- Fix a race when receiving events during reset.
- Change the heartbeat scheduling point.
- Maintainers:
- Change habanalabs maintainer and git repo path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ofir Bitton <obitton@habana.ai>
Link: https://patchwork.freedesktop.org/patch/msgid/ZnfIjTH5AYQvPe7n@obitton-vm-u22.habana-labs.com
<maarten.lankhorst@linux.intel.com>, Maxime Ripard
<mripard@kernel.org>, Thomas Zimmermann <tzimmermann@suse.de>
filp->pid is supposed to be a refcounted pointer; however, before this
patch, drm_file_update_pid() only increments the refcount of a struct
pid after storing a pointer to it in filp->pid and dropping the
dev->filelist_mutex, making the following race possible:
process A process B
========= =========
begin drm_file_update_pid
mutex_lock(&dev->filelist_mutex)
rcu_replace_pointer(filp->pid, <pid B>, 1)
mutex_unlock(&dev->filelist_mutex)
begin drm_file_update_pid
mutex_lock(&dev->filelist_mutex)
rcu_replace_pointer(filp->pid, <pid A>, 1)
mutex_unlock(&dev->filelist_mutex)
get_pid(<pid A>)
synchronize_rcu()
put_pid(<pid B>) *** pid B reaches refcount 0 and is freed here ***
get_pid(<pid B>) *** UAF ***
synchronize_rcu()
put_pid(<pid A>)
As far as I know, this race can only occur with CONFIG_PREEMPT_RCU=y
because it requires RCU to detect a quiescent state in code that is not
explicitly calling into the scheduler.
This race leads to use-after-free of a "struct pid".
It is probably somewhat hard to hit because process A has to pass
through a synchronize_rcu() operation while process B is between
mutex_unlock() and get_pid().
Fix it by ensuring that by the time a pointer to the current task's pid
is stored in the file, an extra reference to the pid has been taken.
This fix also removes the condition for synchronize_rcu(); I think
that optimization is unnecessary complexity, since in that case we
would usually have bailed out on the lockless check above.
Fixes: 1c7a387ffe ("drm: Update file owner during use")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- panic: Monochrome logo support, Various fixes
- ttm: Improve the number of page faults on some platforms, Fix test
build breakage with PREEMPT_RT, more test coverage and various test
improvements
Driver Changes:
- Add missing MODULE_DESCRIPTION where needed
- ipu-v3: Various fixes
- vc4: Monochrome TV support
- bridge:
- analogix_dp: Various improvements and reworks, handle AUX
transfers timeout
- tc358767: Fix DRM_BRIDGE_ATTACH_NO_CONNECTOR, Fix clock
calculations
- panels:
- More transitions to mipi_dsi wrapped functions
- New panels: Lincoln Technologies LCD197, Ortustech COM35H3P70ULC,
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZn1DmQAKCRDj7w1vZxhR
xYj3AP9ThM8q3HoCqXKerpEfnb5LYDB4NocLjn/Bamtm134oNQD+M4Gu2zLSVymV
74PwtPYuQGKWrmXdw0tD70/MtTAihQc=
=fSI4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2024-06-27' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for 6.11:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- panic: Monochrome logo support, Various fixes
- ttm: Improve the number of page faults on some platforms, Fix test
build breakage with PREEMPT_RT, more test coverage and various test
improvements
Driver Changes:
- Add missing MODULE_DESCRIPTION where needed
- ipu-v3: Various fixes
- vc4: Monochrome TV support
- bridge:
- analogix_dp: Various improvements and reworks, handle AUX
transfers timeout
- tc358767: Fix DRM_BRIDGE_ATTACH_NO_CONNECTOR, Fix clock
calculations
- panels:
- More transitions to mipi_dsi wrapped functions
- New panels: Lincoln Technologies LCD197, Ortustech COM35H3P70ULC,
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627-congenial-pistachio-nyala-848cf4@houat
Although designs may contain an ISP IP block, the camera might be a USB
camera. Because of this the ISP firmware is considered optional from
amdgpu. However if the firmware doesn't get loaded the hardware should
not be initialized.
Adjust the return code for early init to ensure the IP block doesn't go
through the other init and fini sequences. Also decrease the message
about firmware load failure to debug so it's not as alarming to users.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
refine isp firmware loading
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove temporary WA to disable ISP prefetch as MMHUB SAW is initialized
to support ISP HW access GART memory using the TLSi path with prefetch
enabled.
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
snprintf can truncate the output fw filename if the isp ucode_prefix
exceeds 29 characters. Knowing ISP ucode_prefix is in the format
isp_x_x_x, limiting the size of ucode_prefix[] to 10 characters
to fix the warning.
Fixes the below warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_isp.c: In function 'isp_early_init':
drivers/gpu/drm/amd/amdgpu/amdgpu_isp.c:192:58: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
192 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s.bin", ucode_prefix);
| ^
In function 'isp_load_fw_by_psp',
inlined from 'isp_early_init' at drivers/gpu/drm/amd/amdgpu/amdgpu_isp.c:218:8:
drivers/gpu/drm/amd/amdgpu/amdgpu_isp.c:192:9: note: 'snprintf' output between 12 and 41 bytes into a destination of size 40
192 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s.bin", ucode_prefix);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable MMHUB prefetch for ISP v4.1.1 as a temporary WA until
the GART supports MMHUB TLSi and SAW for ISP HW to access
GART memory using the TLSi path.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add independent IP centric modules for ISP4.1.0 and ISP4.1.1 hw blocks.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map ISP IH interrupts to Linux generic IRQ for ISP driver to
handle the interrupts using MFD IORESOURCE_IRQ resource.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new config option and set proper dependencies for ISP.
v2: add missed guards, drop separate Kconfig
Reviewed-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Pratap Nirujogi <pratap.nirujogi@amd.com>
Enable ISP for ISP V4.1.0 and V4.1.1 in amdgpu_discovery.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the isp driver in amdgpu to support ISP device on the APUs that
supports ISP IP block. ISP hw block is used for camera front-end, pre
and post processing operations.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ISP hw block is supported in some of the AMD GPU versions, add support
to discover ISP IP in amdgpu_discovery.
v2: squash in documentation update (Alex)
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not return failure for allocating GTT bo with dcc flag on gfx12.
This will improve compatibility for UMD.
Signed-off-by: Frank Min <Frank.Min@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In enable_phantom_plane, we should better check null pointer before
accessing various structs.
Fixes: 09a4ec5da9 ("drm/amd/display: Refactor dc_state interface")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
sriov has the higher bit violation when flushing tlb
[HOW]
normalize the registers to keep lower 16-bit(dword aligned) to aviod higher bit violation
RLCG will mask xcd out and always assume it's accessing its own xcd
v2
add check in wait mem that only do the normalization on regspace
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Yiqing Yao <YiQing.Yao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some register offsets that are required for Display DCC on DCN401
Fixes: 2d072b4456 ("drm/amd: Add reg definitions for DCN401 DCC")
Reported-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. The poison fifo is only used for poison consumption
requests.
2. Merge reset requests when poison fifo caches multiple
poison consumption messages
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to apply to the case where a large number
of ras poison interrupts:
1. Change to use variable to record poison creation
requests to avoid fifo full.
2. Prioritize handling poison creation requests
instead of following the order of requests
received by the driver.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For RAS error scenario, VF guest driver will check mailbox
and set fed flag to avoid unnecessary HW accesses.
additionally, poll for reset completion message first
to avoid accidentally spamming multiple reset requests to host.
v2: add another mailbox check for handling case where kfd detects
timeout first
v3: set host_flr bit and use wait_for_reset
Signed-off-by: Vignesh Chander <Vignesh.Chander@amd.com>
Reviewed-by: Zhigang Luo <Zhigang.Luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add variable to record the deferred error
number read by driver.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So we can get clearer per device logging.
Signed-off-by: Vignesh Chander <Vignesh.Chander@amd.com>
Reviewed-by: Zhigang Luo <Zhigang.Luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
Setting IH_RB_WPTR register to 0 will not clear the RB_OVERFLOW bit
if RB_ENABLE is not set.
How to fix:
Set WPTR_OVERFLOW_CLEAR bit after RB_ENABLE bit is set.
The RB_ENABLE bit is required to be set, together with
WPTR_OVERFLOW_ENABLE bit so that setting WPTR_OVERFLOW_CLEAR bit
would clear the RB_OVERFLOW.
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit d3620eeae8.
Revert this due to a final solution:
commit ed3165d660 ("drm/amdgpu/jpeg5: reprogram doorbell setting after power up for each playback")
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Sonny Jiang <sonjiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use existing swap() function rather than duplicating its implementation.
./drivers/gpu/drm/amd/display/dc/dml2/dml21/src/dml2_pmo/dml2_pmo_dcn4_fams2.c:1171:103-104: WARNING opportunity for swap().
./drivers/gpu/drm/amd/display/dc/dml2/dml21/src/dml2_pmo/dml2_pmo_dcn4_fams2.c:1231:99-100: WARNING opportunity for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9400
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function are defined in the amdgpu_dm.c file, but not called
anywhere, so delete the unused function.
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:371:20: warning: unused function 'reverse_planes_order'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9402
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use of macro ARRAY_SIZE to calculate array size minimizes
the redundant code and improves code reusability.
./drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c:164:45-46: WARNING: Use ARRAY_SIZE.
./drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c:183:47-48: WARNING: Use ARRAY_SIZE.
./drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c:237:45-46: WARNING: Use ARRAY_SIZE.
./drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c:257:47-48: WARNING: Use ARRAY_SIZE.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9405
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>