If fallcate is implemented but zero and discard operations are not
supported by the filesystem the backing file is on we continue to fill
dmesg with errors from the blk_mq_end_request() since each time we call
fallocate() on the loop device the EOPNOTSUPP error from lo_fallocate()
ends up propagated into the block layer. In the end syscall succeeds
since the blkdev_issue_zeroout() falls back to writing zeroes which
makes the errors even more misleading and confusing.
How to reproduce:
1. make sure /tmp is mounted as tmpfs
2. dd if=/dev/zero of=/tmp/disk.img bs=1M count=100
3. losetup /dev/loop0 /tmp/disk.img
4. mkfs.ext2 /dev/loop0
5. dmesg |tail
[710690.898214] operation not supported error, dev loop0, sector 204672 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898279] operation not supported error, dev loop0, sector 522 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898603] operation not supported error, dev loop0, sector 16906 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898917] operation not supported error, dev loop0, sector 32774 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899218] operation not supported error, dev loop0, sector 49674 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899484] operation not supported error, dev loop0, sector 65542 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899743] operation not supported error, dev loop0, sector 82442 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900015] operation not supported error, dev loop0, sector 98310 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900276] operation not supported error, dev loop0, sector 115210 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900546] operation not supported error, dev loop0, sector 131078 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
This patch changes the lo_fallocate() to clear the flags for zero and
discard operations if we get EOPNOTSUPP from the backing file fallocate
callback, that way we at least stop spewing errors after the first
unsuccessful try.
CC: Jan Kara <jack@suse.cz>
Signed-off-by: Cyril Hrubis <chrubis@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240613163817.22640-1-chrubis@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SCSI Removable Media Bit (RMB) should only be set for removable media,
where the device stays and the media changes, e.g. CD-ROM or floppy.
The ATA removable media device bit is obsoleted since ATA-8 ACS (2006),
but before that it was used to indicate that the device can have its media
removed (while the device stays).
Commit 8a3e33cf92 ("ata: ahci: find eSATA ports and flag them as
removable") introduced a change to set the RMB bit if the port has either
the eSATA bit or the hot-plug capable bit set. The reasoning was that the
author wanted his eSATA ports to get treated like a USB stick.
This is however wrong. See "20-082r23SPC-6: Removable Medium Bit
Expectations" which has since been integrated to SPC, which states that:
"""
Reports have been received that some USB Memory Stick device servers set
the removable medium (RMB) bit to one. The rub comes when the medium is
actually removed, because... The device server is removed concurrently
with the medium removal. If there is no device server, then there is no
device server that is waiting to have removable medium inserted.
Sufficient numbers of SCSI analysts see such a device:
- not as a device that supports removable medium;
but
- as a removable, hot pluggable device.
"""
The definition of the RMB bit in the SPC specification has since been
clarified to match this.
Thus, a USB stick should not have the RMB bit set (and neither shall an
eSATA nor a hot-plug capable port).
Commit dc8b4afc4a ("ata: ahci: don't mark HotPlugCapable Ports as
external/removable") then changed so that the RMB bit is only set for the
eSATA bit (and not for the hot-plug capable bit), because of a lot of bug
reports of SATA devices were being automounted by udisks. However,
treating eSATA and hot-plug capable ports differently is not correct.
From the AHCI 1.3.1 spec:
Hot Plug Capable Port (HPCP): When set to '1', indicates that this port's
signal and power connectors are externally accessible via a joint signal
and power connector for blindmate device hot plug.
So a hot-plug capable port is an external port, just like commit
45b96d65ec ("ata: ahci: a hotplug capable port is an external port")
claims.
In order to not violate the SPC specification, modify the SCSI INQUIRY
data to only set the RMB bit if the ATA device can have its media removed.
This fixes a reported problem where GNOME/udisks was automounting devices
connected to hot-plug capable ports.
Fixes: 45b96d65ec ("ata: ahci: a hotplug capable port is an external port")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Reported-by: Thomas Weißschuh <linux@weissschuh.net>
Closes: https://lore.kernel.org/linux-ide/c0de8262-dc4b-4c22-9fac-33432e5bddd3@t-8ch.de/
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[cassel: wrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
The declaration of xe_reg_whitelist_process_engine() function does
not fit into "xe_wa.h" and is already a duplicate.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613195702.2164-1-michal.wajdeczko@intel.com
ovl_check_encode_origin() should return a positive number if the lower
dentry is to be encoded, zero otherwise. If there's no upper layer at all
(read-only overlay), then it obviously needs to return positive.
This was broken by commit 16aac5ad1f ("ovl: support encoding
non-decodable file handles"), which didn't take the lower-only
configuration into account.
Fix by checking the no-upper-layer case up-front.
Reported-and-tested-by: Youzhong Yang <youzhong@gmail.com>
Closes: https://lore.kernel.org/all/CADpNCvaBimi+zCYfRJHvCOhMih8OU0rmZkwLuh24MKKroRuT8Q@mail.gmail.com/
Fixes: 16aac5ad1f ("ovl: support encoding non-decodable file handles")
Cc: <stable@vger.kernel.org> # v6.6
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
While we list the "IRQ status *and acknowledge*" registers as volatile
in the MFD description, they are missing from the writable range array,
so acknowledging any interrupts was met with an -EIO error.
This error propagates up, leading to the whole AXP717 driver failing to
probe, which is fatal to most systems using this PMIC, since most
peripherals refer one of the PMIC voltage rails.
This wasn't noticed on the initial submission, since the interrupt was
completely missing at this point, but the DTs now merged describe the
interrupt, creating the problem.
Add the five registers that hold those bits to the writable array.
This fixes the boot on the Anbernic systems using the AXP717 PMIC.
Fixes: b5bfc8ab24 ("mfd: axp20x: Add support for AXP717 PMIC")
Reported-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/r/20240613233104.17529-1-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>
In order to be able to use the proper register macros instead of the
underscore prefixed ones, pass i915_reg_t for the calc_index()
parameters.
Side note: DSPSURF is really about planes, not pipes. Fixed stride
doesn't work for plane C for CHV (but that's okay for gvt). This doesn't
support planes beyond C either. But all that is unrelated to the change
at hand.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.wang.linux@gmail.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Reviewed-by: Zhi Wang <zhiwang@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/282b19c44d83c96b52c261cfc7218e7e54076cba.1717773890.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As the comment in this function says, the code currently just clears the
CIPSO part with IPOPT_NOP, rather than removing it completely and
trimming the packet. The other cipso_v4_*_delattr() functions, however,
do the proper removal and also calipso_skbuff_delattr() makes an effort
to remove the CALIPSO options instead of replacing them with padding.
Some routers treat IPv4 packets with anything (even NOPs) in the option
header as a special case and take them through a slower processing path.
Consequently, hardening guides such as STIG recommend to configure such
routers to drop packets with non-empty IP option headers [1][2]. Thus,
users might expect NetLabel to produce packets with minimal padding (or
at least with no padding when no actual options are present).
Implement the proper option removal to address this and to be closer to
what the peer functions do.
[1] https://www.stigviewer.com/stig/juniper_router_rtr/2019-09-27/finding/V-90937
[2] https://www.stigviewer.com/stig/cisco_ios_xe_router_rtr/2021-03-26/finding/V-217001
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As evident from the definition of ip_options_get(), the IP option
IPOPT_END is used to pad the IP option data array, not IPOPT_NOP. Yet
the loop that walks the IP options to determine the total IP options
length in cipso_v4_delopt() doesn't take IPOPT_END into account.
Fix it by recognizing the IPOPT_END value as the end of actual options.
Fixes: 014ab19a69 ("selinux: Set socket NetLabel based on connection endpoint")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new HW is more power efficient and there is no
need to enter the D0i3/D3 so quickly. Increasing
autosuspend delay reduces latency in certain usage
scenarios.
Signed-off-by: Andrzej Kacprowski <Andrzej.Kacprowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-14-jacek.lawrynowicz@linux.intel.com
Add new test mode flag that will disable all timeouts
defined in timeout fields of struct ivpu_device.
Remove also reschedule_suspend field as it is unused.
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-11-jacek.lawrynowicz@linux.intel.com
Implement setting specified buffer ranges as read-only.
In case if specified range is not 64K aligned and 64K contiguous
MMU600 pages are turned on, split 64K mapping to allow 4K granularity
for read-only configuration.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-10-jacek.lawrynowicz@linux.intel.com
When host system is under heavy load and the NPU is already running
on the lowest frequency, PUNIT may request Duty Cycle Throttling (DCT).
This will further reduce NPU power usage.
PUNIT requests DCT mode using Survabilty IRQ and mailbox register.
The driver then issues a JSM message to the FW that enables
the DCT mode. If the NPU resets while in DCT mode, the driver request
DCT mode during FW boot.
Also add debugfs "dct" file that allows to set arbitrary DCT percentage,
which is used by driver tests.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-7-jacek.lawrynowicz@linux.intel.com
It is required to disable NPU clock relinquish for the time
of MMIO reset. Clock relinquish gets into default (enabled)
state after MMIO reset is performed.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-6-jacek.lawrynowicz@linux.intel.com
Abort all jobs that belong to contexts generating MMU faults in order
to avoid flooding host with MMU IRQs.
Jobs are cancelled with:
- SSID_RELEASE command when OS scheduling is enabled
- DESTROY_CMDQ command when HW scheduling is enabled
Signed-off-by: Maciej Falkowski <maciej.falkowski@intel.com>
Co-developed-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-3-jacek.lawrynowicz@linux.intel.com
Send workpoint 0 request during power up on 37xx.
This is needed in rare case where WP0 was not sent
during power down due to device hang.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-2-jacek.lawrynowicz@linux.intel.com
req->n_channels must be set before req->channels[] can be used.
This patch fixes one of the issues encountered in [1].
[ 83.964255] UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:364:4
[ 83.964258] index 0 is out of range for type 'struct ieee80211_channel *[]'
[...]
[ 83.964264] Call Trace:
[ 83.964267] <TASK>
[ 83.964269] dump_stack_lvl+0x3f/0xc0
[ 83.964274] __ubsan_handle_out_of_bounds+0xec/0x110
[ 83.964278] ieee80211_prep_hw_scan+0x2db/0x4b0
[ 83.964281] __ieee80211_start_scan+0x601/0x990
[ 83.964291] nl80211_trigger_scan+0x874/0x980
[ 83.964295] genl_family_rcv_msg_doit+0xe8/0x160
[ 83.964298] genl_rcv_msg+0x240/0x270
[...]
[1] https://bugzilla.kernel.org/show_bug.cgi?id=218810
Co-authored-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Kenton Groombridge <concord@gentoo.org>
Link: https://msgid.link/20240605152218.236061-1-concord@gentoo.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the debugfs functions have no-op stubs for CONFIG_DEBUG_FS=n,
the compiler will optimize the rest away since they are no longer referenced.
The benefit of removing the conditional compilation is that the build
is actually tested for both CONFIG_DEBUG_FS configuration values.
Assuming most developers have it enabled, CONFIG_DEBUG_FS=n is not tested
much and may fail the build due to the conditional compilation.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240606120842.1377267-1-pengfuyuan@kylinos.cn
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The syzbot fuzzer found that the interrupt-URB completion callback in
the cdc-wdm driver was taking too long, and the driver's immediate
resubmission of interrupt URBs with -EPROTO status combined with the
dummy-hcd emulation to cause a CPU lockup:
cdc_wdm 1-1:1.0: nonzero urb status received: -71
cdc_wdm 1-1:1.0: wdm_int_callback - 0 bytes
watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [syz-executor782:6625]
CPU#0 Utilization every 4s during lockup:
#1: 98% system, 0% softirq, 3% hardirq, 0% idle
#2: 98% system, 0% softirq, 3% hardirq, 0% idle
#3: 98% system, 0% softirq, 3% hardirq, 0% idle
#4: 98% system, 0% softirq, 3% hardirq, 0% idle
#5: 98% system, 1% softirq, 3% hardirq, 0% idle
Modules linked in:
irq event stamp: 73096
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_emit_next_record kernel/printk/printk.c:2935 [inline]
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_flush_all+0x650/0xb74 kernel/printk/printk.c:2994
hardirqs last disabled at (73096): [<ffff80008af10b00>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline]
hardirqs last disabled at (73096): [<ffff80008af10b00>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551
softirqs last enabled at (73048): [<ffff8000801ea530>] softirq_handle_end kernel/softirq.c:400 [inline]
softirqs last enabled at (73048): [<ffff8000801ea530>] handle_softirqs+0xa60/0xc34 kernel/softirq.c:582
softirqs last disabled at (73043): [<ffff800080020de8>] __do_softirq+0x14/0x20 kernel/softirq.c:588
CPU: 0 PID: 6625 Comm: syz-executor782 Tainted: G W 6.10.0-rc2-syzkaller-g8867bbd4a056 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Testing showed that the problem did not occur if the two error
messages -- the first two lines above -- were removed; apparently adding
material to the kernel log takes a surprisingly large amount of time.
In any case, the best approach for preventing these lockups and to
avoid spamming the log with thousands of error messages per second is
to ratelimit the two dev_err() calls. Therefore we replace them with
dev_err_ratelimited().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Reported-and-tested-by: syzbot+5f996b83575ef4058638@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/00000000000073d54b061a6a1c65@google.com/
Reported-and-tested-by: syzbot+1b2abad17596ad03dcff@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000f45085061aa9b37e@google.com/
Fixes: 9908a32e94 ("USB: remove err() macro from usb class drivers")
Link: https://lore.kernel.org/linux-usb/40dfa45b-5f21-4eef-a8c1-51a2f320e267@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/29855215-52f5-4385-b058-91f42c2bee18@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the current owner of a request is allowed to write into req->flags.
Hence, the cancellation path should never touch it. Add a new field
instead of the flag, move it into the 3rd cache line because it should
always be initialised. poll_refs can move further as polling is an
involved process anyway.
It's a minimal patch, in the future we can and should find a better
place for it and remove now unused REQ_F_CANCEL_SEQ.
Fixes: 521223d7c2 ("io_uring/cancel: don't default to setting req->work.cancel_seq")
Cc: stable@vger.kernel.org
Reported-by: Li Shi <sl1589472800@gmail.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/6827b129f8f0ad76fa9d1f0a773de938b240ffab.1718323430.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Xe Maintainers update to MAINTAINERS file.
Driver Changes:
- Use correct forcewake assertions.
- Assert that VRAM provisioning is only done on DGFX.
- Flush render caches before user-fence signalling on all engines.
- Move the disable_c6 call since it was sometimes never called.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRskUM7w1oG5rx2IZO4FpNVCsYGvwUCZmrWQwAKCRC4FpNVCsYG
v5BIAP9gS5S9mRVp9h+vgo5U84h2VUDT3IoKBEFslkmhKuFATwEAsfbr2m3fD5RT
idAbg0enxy5V/etTB7oK/1TaSKFAqwo=
=ApmP
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-fixes-2024-06-13' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Core Changes:
- Xe Maintainers update to MAINTAINERS file.
Driver Changes:
- Use correct forcewake assertions.
- Assert that VRAM provisioning is only done on DGFX.
- Flush render caches before user-fence signalling on all engines.
- Move the disable_c6 call since it was sometimes never called.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZmrXV0FoBb8M0c6J@fedora
Prepare for skipping the IO Advice Hints Grouping mode page for USB storage
devices.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Joao Machado <jocrismachado@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Christian Heusel <christian@heusel.eu>
Cc: stable@vger.kernel.org
Fixes: 4f53138fff ("scsi: sd: Translate data lifetime information")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240613211828.2077477-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under the conditions that a device is to be reinitialized within
ufshcd_probe_hba(), the device must first be fully reset.
Resetting the device should include freeing U8 model (member of dev_info)
but does not, and this causes a memory leak. ufs_put_device_desc() is
responsible for freeing model.
unreferenced object 0xffff3f63008bee60 (size 32):
comm "kworker/u33:1", pid 60, jiffies 4294892642
hex dump (first 32 bytes):
54 48 47 4a 46 47 54 30 54 32 35 42 41 5a 5a 41 THGJFGT0T25BAZZA
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc ed7ff1a9):
[<ffffb86705f1243c>] kmemleak_alloc+0x34/0x40
[<ffffb8670511cee4>] __kmalloc_noprof+0x1e4/0x2fc
[<ffffb86705c247fc>] ufshcd_read_string_desc+0x94/0x190
[<ffffb86705c26854>] ufshcd_device_init+0x480/0xdf8
[<ffffb86705c27b68>] ufshcd_probe_hba+0x3c/0x404
[<ffffb86705c29264>] ufshcd_async_scan+0x40/0x370
[<ffffb86704f43e9c>] async_run_entry_fn+0x34/0xe0
[<ffffb86704f34638>] process_one_work+0x154/0x298
[<ffffb86704f34a74>] worker_thread+0x2f8/0x408
[<ffffb86704f3cfa4>] kthread+0x114/0x118
[<ffffb86704e955a0>] ret_from_fork+0x10/0x20
Fixes: 96a7141da3 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Joel Slebodnick <jslebodn@redhat.com>
Link: https://lore.kernel.org/r/20240613200202.2524194-1-jslebodn@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Fix an regression issue by adding 640x480 fallback mode
for Exynos HDMI driver.
Bug fix
- Fix a memory leak by ensuring the duplicated EDID is properly freed in the get_modes function.
Code cleanup
- Remove redundant driver owner initialization since platform_driver_register() sets it automatically.
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEEoxi+6c5pRPV/gdXcxWAb7Og/+bYFAmZmp5AACgkQxWAb7Og/
+baPmgv+NPpwekmg/MVid5E2UBPohPZ0qfB6AoDVUdN4vPYEzw5p9PRwcQ8vW/1u
K0rAGrmgGZZluYWz4OI0bQkA99Cxk6M9+knERxOtvODrf/G3oU2FVVq1s1u831Vo
wjjUMePrih2tpINrTu7EBTJSLVfOdsvkw3lOwfQlawrSm2YUZQKoWRpg4lL1bv9C
moXLnxDcz+DW3/Mv8GqfQwTxMwz5F1CSIqx/lJXzMo9FaR5B9mlgamCIRakEYkZo
CAqMASfDOyBWrbkSX3Yw7msmWWtZXEB5ICHsK4p8DGkaAEdzDGwDL1m8c0w/+0BU
sclpWXy01Y2fe22IJ/VwvAnFOGBY5+nNN47jkrDzgOwaPzC6Yaw9FUCPbnSIQBPs
eVfypoQxB5j9QsalxpTMmxzBZPGaa33mOuklsV2SGM7p4HJrf2NCDZCZiyp5Midp
bYpNEtZKjFzmb5+tov/sWegcZfo+qSBsN6JmHgFkt7ibJvaZGhj0/qnvMyyYEoTH
kArxG9kt
=ydsM
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-fixes-for-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Regression fix
- Fix an regression issue by adding 640x480 fallback mode
for Exynos HDMI driver.
Bug fix
- Fix a memory leak by ensuring the duplicated EDID is properly freed in the get_modes function.
Code cleanup
- Remove redundant driver owner initialization since platform_driver_register() sets it automatically.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610073839.37430-1-inki.dae@samsung.com
This function wants to move a subset of a list from one element to the
tail into another list. It also needs to use the srcu synchronize
instead of the regular rcu version. Do this one element at a time
because that's the only to do it.
Fixes: be647e2c76 ("nvme: use srcu for iterating namespace list")
Reported-by: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
If inc_block_group_ro systematically fails (e.g. due to ETXTBUSY from
swap) or btrfs_relocate_chunk systematically fails (from lack of
space), then this worker becomes an infinite loop.
At the very least, this strands the cleaner thread, but can also result
in hung tasks/RCU stalls on PREEMPT_NONE kernels and if the
reclaim_bgs_lock mutex is not contended.
I believe the best long term fix is to manage reclaim via work queue,
where we queue up a relocation on the triggering condition and re-queue
on failure. In the meantime, this is an easy fix to apply to avoid the
immediate pain.
Fixes: 7e27180994 ("btrfs: reinsert BGs failed to reclaim")
CC: stable@vger.kernel.org # 6.6+
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The IS_SRIOV macro returns true also when we are running as a PF
driver. Use correct IS_SRIOV_VF macro to skip force-wake management.
Fixes: 513ea833c2 ("drm/xe/vf: Ignore force-wake requests if VF")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613120749.2032-1-michal.wajdeczko@intel.com
Add a connector debugfs entry to force retrain an active link. This can
be used to test both custom link parameters (previously forced via the
force_link_rate/lane_count entries) or link train failure scenarios
(previously forced via the force_link_training_failure entry). The entry
will autoreset after the link-retrain is complete.
v2: Add the entry from intel_dp_link_training.c (Jani)
v3: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-21-imre.deak@intel.com
Add a connector debugfs entry to force a failure during the following
1-2 link training. The entry will auto-reset after the specified link
training events are complete.
v2: Add the entry from intel_dp_link_training.c (Jani)
v3: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-20-imre.deak@intel.com
Add connector debugfs entries to get the maximum link rate and lane
count.
v2: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-19-imre.deak@intel.com