commit 854e8bb1aa upstream.
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit aedd153f5b upstream.
Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.
Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed
The fix is similar to 1658f914ff ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8117/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d022a65ed2 upstream.
Using a VID value that is not high enough for the requested P state can
cause machine checks. Add a ceiling function to ensure calulated VIDs
with fractional values are set to the next highest integer VID value.
The algorythm for calculating the non-trubo VID from the BIOS writers
guide is:
vid_ratio = (vid_max - vid_min) / (max_pstate - min_pstate)
vid = ceiling(vid_min + (req_pstate - min_pstate) * vid_ratio)
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b27580b05e upstream.
BYT has a different conversion from P state to frequency than the core
processors. This causes the min/max and current frequency to be
misreported on some BYT SKUs. Tested on BYT N2820, Ivybridge and
Haswell processors.
Link: https://bugzilla.yoctoproject.org/show_bug.cgi?id=6663
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c034871712 upstream.
The user may have custom settings don't destroy them during suspend.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80651
Reported-by: Tobias Jakobi <liquid.acid@gmx.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4521e1a0ce upstream.
Some BIOSes modify the state of MSR_IA32_MISC_ENABLE_TURBO_DISABLE
based on the current power source for the system battery AC vs
battery. Reflect the correct current state and ability to modify the
no_turbo sysfs file based on current state of
MSR_IA32_MISC_ENABLE_TURBO_DISABLE.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=83151
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c034b02e21 upstream.
Currently the core does not expose scaling_cur_freq for set_policy()
drivers this breaks some userspace monitoring tools.
Change the core to expose this file for all drivers and if the
set_policy() driver supports the get() callback use it to retrieve the
current frequency.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73741
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 36b4bed5cd upstream.
Code which changes policy to powersave changes also max_policy_pct based on
max_freq. Code which change max_perf_pct has upper limit base on value
max_policy_pct. When policy is changing from powersave back to performance
then max_policy_pct is not changed. Which means that changing max_perf_pct is
not possible to high values if max_freq was too low in powersave policy.
Test case:
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
800000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
100
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 20 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
800000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
20
$ echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 3300000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 100 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
24
And now intel_pstate driver allows to set maximal value for max_perf_pct based
on max_policy_pct which is 24 for previous powersave max_freq 800000.
This patch will set default value for max_policy_pct when setting policy to
performance so it will allow to set also max value for max_perf_pct.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c0c3e735fa upstream.
qemu as used by xend/xm toolstack uses a different subvendor id.
Bind the drm driver also to this emulated card.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9e0f162a36 upstream.
In commit 8393c524a2 (MIPS: tlbex: Fix a missing statement for
HUGETLB), the TLB Refill handler was fixed so that non-OCTEON targets
would work properly with huge pages. The change was incorrect in that
it broke the OCTEON case.
The problem is shown here:
xxx0: df7a0000 ld k0,0(k1)
.
.
.
xxxc0: df610000 ld at,0(k1)
xxxc4: 335a0ff0 andi k0,k0,0xff0
xxxc8: e825ffcd bbit1 at,0x5,0x0
xxxcc: 003ad82d daddu k1,at,k0
.
.
.
In the non-octeon case there is a destructive test for the huge PTE
bit, and then at 0, $k0 is reloaded (that is what the 8393c524a2
patch added).
In the octeon case, we modify k1 in the branch delay slot, but we
never need k0 again, so the new load is not needed, but since k1 is
modified, if we do the load, we load from a garbage location and then
get a nested TLB Refill, which is seen in userspace as either SIGBUS
or SIGSEGV (depending on the garbage).
The real fix is to only do this reloading if it is needed, and never
where it is harmful.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit aa08ed5544 upstream.
During 3.16 merge window, parts of the commit 8e8acb3296
(MIPS/loongson2_cpufreq: Fix CPU clock rate setting) seem to have
been deleted probably due to a mismerge, and as a result cpufreq
is broken again on Loongson2 boards in 3.16 and newer kernels.
Fix by repeating the fix.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c572aaf46f upstream.
Limit primary to qemu vgamem size, to avoid reaching
qemu guest bug "requested primary larger than framebuffer"
on resizing screen too large to fit.
Remove unneeded and misleading variables.
Related to:
https://bugzilla.redhat.com/show_bug.cgi?id=1127552
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5695be142e upstream.
PM freezer relies on having all tasks frozen by the time devices are
getting frozen so that no task will touch them while they are getting
frozen. But OOM killer is allowed to kill an already frozen task in
order to handle OOM situtation. In order to protect from late wake ups
OOM killer is disabled after all tasks are frozen. This, however, still
keeps a window open when a killed task didn't manage to die by the time
freeze_processes finishes.
Reduce the race window by checking all tasks after OOM killer has been
disabled. This is still not race free completely unfortunately because
oom_killer_disable cannot stop an already ongoing OOM killer so a task
might still wake up from the fridge and get killed without
freeze_processes noticing. Full synchronization of OOM and freezer is,
however, too heavy weight for this highly unlikely case.
Introduce and check oom_kills counter which gets incremented early when
the allocator enters __alloc_pages_may_oom path and only check all the
tasks if the counter changes during the freezing attempt. The counter
is updated so early to reduce the race window since allocator checked
oom_killer_disabled which is set by PM-freezing code. A false positive
will push the PM-freezer into a slow path but that is not a big deal.
Changes since v1
- push the re-check loop out of freeze_processes into
check_frozen_processes and invert the condition to make the code more
readable as per Rafael
Fixes: f660daac47 (oom: thaw threads if oom killed thread is frozen before deferring)
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 51fae6da64 upstream.
Since f660daac47 (oom: thaw threads if oom killed thread is frozen
before deferring) OOM killer relies on being able to thaw a frozen task
to handle OOM situation but a3201227f8 (freezer: make freezing() test
freeze conditions in effect instead of TIF_FREEZE) has reorganized the
code and stopped clearing freeze flag in __thaw_task. This means that
the target task only wakes up and goes into the fridge again because the
freezing condition hasn't changed for it. This reintroduces the bug
fixed by f660daac47.
Fix the issue by checking for TIF_MEMDIE thread flag in
freezing_slow_path and exclude the task from freezing completely. If a
task was already frozen it would get woken by __thaw_task from OOM killer
and get out of freezer after rechecking freezing().
Changes since v1
- put TIF_MEMDIE check into freezing_slowpath rather than in __refrigerator
as per Oleg
- return __thaw_task into oom_scan_process_thread because
oom_kill_process will not wake task in the fridge because it is
sleeping uninterruptible
[mhocko@suse.cz: rewrote the changelog]
Fixes: a3201227f8 (freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE)
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a5466d7bba upstream.
Commit 08a07904e1 ("MIPS: math-emu: Remove most ifdefery") removed
the #ifdef ISA conditions and switched to runtime detection. However,
according to the instruction set manual, the cop1x_op instructions are
available in >=MIPS32r2 as well. This fixes a problem on MIPS32r2
with the ntpd package which failed to execute with a SIGILL exit code due
to the fact that a madd.d instruction was not being emulated.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 08a07904e1 ("MIPS: math-emu: Remove most ifdefery")
Cc: linux-mips@linux-mips.org
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/8173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d4c5efdb97 upstream.
zatimend has reported that in his environment (3.16/gcc4.8.3/corei7)
memset() calls which clear out sensitive data in extract_{buf,entropy,
entropy_user}() in random driver are being optimized away by gcc.
Add a helper memzero_explicit() (similarly as explicit_bzero() variants)
that can be used in such cases where a variable with sensitive data is
being cleared out in the end. Other use cases might also be in crypto
code. [ I have put this into lib/string.c though, as it's always built-in
and doesn't need any dependencies then. ]
Fixes kernel bugzilla: 82041
Reported-by: zatimend@hotmail.co.uk
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[ kamal: backport to 3.13-stable: one more memzero_explicit in extract_buf() ]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit adfed2b058 upstream.
Avoids HDP cache flush issues when using vram which can
cause ring test failures on certain boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alexander Fyodorov <halcy@yandex.ru>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4910403836 upstream.
If the sad_count is 0, set the hw to stereo and change
the error message to a warn. A lot of monitors don't
set the speaker allocation block.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 813d32f913 upstream.
Convert the ext4_has_group_desc_csum predicate to look for a checksum
driver instead of the metadata_csum flag and change the bg checksum
calculation function to look for GDT_CSUM before taking the crc16
path.
Without this patch, if we mount with ^uninit_bg,^metadata_csum and
later metadata_csum gets turned on by accident, the block group
checksum functions will incorrectly assume that checksumming is
enabled (metadata_csum) but that crc16 should be used
(!s_chksum_driver). This is totally wrong, so fix the predicate
and the checksum formula selection.
(Granted, if the metadata_csum feature bit gets enabled on a live FS
then something underhanded is going on, but we could at least avoid
writing garbage into the on-disk fields.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ebc0c74e76 upstream.
Order of registers has changed in GDB moving from 6.8 to 7.5. This patch
updates KGDB to work properly with GDB 7.5, though makes it incompatible
with 6.8.
Signed-off-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5c05483e2d upstream.
There are certain test configuration of virtual platform which don't
have any real console device (uart/pgu). So add tty0 as a fallback console
device to allow system to boot and be accessible via telnet
Otherwise with ttyS0 as only console, but 8250 disabled in kernel build,
init chokes.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9aa5d32ba2 upstream.
Besides the fact that this replacement improves code readability
it also protects from errors caused direct EXT4_S(sb)->s_es manipulation
which may result attempt to use uninitialized csum machinery.
#Testcase_BEGIN
IMG=/dev/ram0
MNT=/mnt
mkfs.ext4 $IMG
mount $IMG $MNT
#Enable feature directly on disk, on mounted fs
tune2fs -O metadata_csum $IMG
# Provoke metadata update, likey result in OOPS
touch $MNT/test
umount $MNT
#Testcase_END
# Replacement script
@@
expression E;
@@
- EXT4_HAS_RO_COMPAT_FEATURE(E, EXT4_FEATURE_RO_COMPAT_METADATA_CSUM)
+ ext4_has_metadata_csum(E)
https://bugzilla.kernel.org/show_bug.cgi?id=82201
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0ff8947fc5 upstream.
Delalloc write journal reservations only reserve 1 credit,
to update the inode if necessary. However, it may happen
once in a filesystem's lifetime that a file will cross
the 2G threshold, and require the LARGE_FILE feature to
be set in the superblock as well, if it was not set already.
This overruns the transaction reservation, and can be
demonstrated simply on any ext4 filesystem without the LARGE_FILE
feature already set:
dd if=/dev/zero of=testfile bs=1 seek=2147483646 count=1 \
conv=notrunc of=testfile
sync
dd if=/dev/zero of=testfile bs=1 seek=2147483647 count=1 \
conv=notrunc of=testfile
leads to:
EXT4-fs: ext4_do_update_inode:4296: aborting transaction: error 28 in __ext4_handle_dirty_super
EXT4-fs error (device loop0) in ext4_do_update_inode:4301: error 28
EXT4-fs error (device loop0) in ext4_reserve_inode_write:4757: Readonly filesystem
EXT4-fs error (device loop0) in ext4_dirty_inode:4876: error 28
EXT4-fs error (device loop0) in ext4_da_write_end:2685: error 28
Adjust the number of credits based on whether the flag is
already set, and whether the current write may extend past the
LARGE_FILE limit.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f4bb298102 upstream.
If there is a corrupted file system which has directory entries that
point at reserved, metadata inodes, prohibit them from being used by
treating them the same way we treat Boot Loader inodes --- that is,
mark them to be bad inodes. This prohibits them from being opened,
deleted, or modified via chmod, chown, utimes, etc.
In particular, this prevents a corrupted file system which has a
directory entry which points at the journal inode from being deleted
and its blocks released, after which point Much Hilarity Ensues.
Reported-by: Sami Liedes <sami.liedes@iki.fi>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e2bfb088fa upstream.
The boot loader inode (inode #5) should never be visible in the
directory hierarchy, but it's possible if the file system is corrupted
that there will be a directory entry that points at inode #5. In
order to avoid accidentally trashing it, when such a directory inode
is opened, the inode will be marked as a bad inode, so that it's not
possible to modify (or read) the inode from userspace.
Unfortunately, when we unlink this (invalid/illegal) directory entry,
we will put the bad inode on the ophan list, and then when try to
unlink the directory, we don't actually remove the bad inode from the
orphan list before freeing in-memory inode structure. This means the
in-memory orphan list is corrupted, leading to a kernel oops.
In addition, avoid truncating a bad inode in ext4_destroy_inode(),
since truncating the boot loader inode is not a smart thing to do.
Reported-by: Sami Liedes <sami.liedes@iki.fi>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0d0f660d88 upstream.
This patch explicitly disables TX completion interrupt coalescing logic
in isert_put_response() and isert_put_datain() that was originally added
as an efficiency optimization in commit 95b60f07.
It has been reported that this change can trigger ABORT_TASK timeouts
under certain small block workloads, where disabling coalescing was
required for stability. According to Sagi, this doesn't impact
overall performance, so go ahead and disable it for now.
Reported-by: Moussa Ba <moussaba@micron.com>
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e24805637d upstream.
This patch fixes a bug in handling of SPC-3 PR Activate Persistence
across Target Power Loss (APTPL) logic where re-creation of state for
MappedLUNs from dynamically generated NodeACLs did not occur during
I_T Nexus establishment.
It adds the missing core_scsi3_check_aptpl_registration() call during
core_tpg_check_initiator_node_acl() -> core_tpg_add_node_to_devs() in
order to replay any pre-loaded APTPL metadata state associated with
the newly connected SCSI Initiator Port.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f4c24db1b7 upstream.
The code is currently riddled with "drop the hardware_lock to avoid a
deadlock" bugs that expose races. One of those races seems to expose a
valid warning in tcm_qla2xxx_clear_nacl_from_fcport_map. Add some
bandaid to it.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d6320cbfc9 upstream.
Use truncate_isize_extended() when hole is being created in a file so that
->page_mkwrite() will get called for the partial tail page if it is
mmaped (see the first patch in the series for details).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 90a8020278 upstream.
->page_mkwrite() is used by filesystems to allocate blocks under a page
which is becoming writeably mmapped in some process' address space. This
allows a filesystem to return a page fault if there is not enough space
available, user exceeds quota or similar problem happens, rather than
silently discarding data later when writepage is called.
However VFS fails to call ->page_mkwrite() in all the cases where
filesystems need it when blocksize < pagesize. For example when
blocksize = 1024, pagesize = 4096 the following is problematic:
ftruncate(fd, 0);
pwrite(fd, buf, 1024, 0);
map = mmap(NULL, 1024, PROT_WRITE, MAP_SHARED, fd, 0);
map[0] = 'a'; ----> page_mkwrite() for index 0 is called
ftruncate(fd, 10000); /* or even pwrite(fd, buf, 1, 10000) */
mremap(map, 1024, 10000, 0);
map[4095] = 'a'; ----> no page_mkwrite() called
At the moment ->page_mkwrite() is called, filesystem can allocate only
one block for the page because i_size == 1024. Otherwise it would create
blocks beyond i_size which is generally undesirable. But later at
->writepage() time, we also need to store data at offset 4095 but we
don't have block allocated for it.
This patch introduces a helper function filesystems can use to have
->page_mkwrite() called at all the necessary moments.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 082f58ac4a upstream.
During temporary resource starvation at lower transport layer, command
is placed on queue full retry path, which expose this problem. The TCM
queue full handling of SCF_TRANSPORT_TASK_SENSE currently sends the same
cmd twice to lower layer. The 1st time led to cmd normal free path.
The 2nd time cause Null pointer access.
This regression bug was originally introduced v3.1-rc code in the
following commit:
commit e057f53308
Author: Christoph Hellwig <hch@infradead.org>
Date: Mon Oct 17 13:56:41 2011 -0400
target: remove the transport_qf_callback se_cmd callback
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 279bf6d390 upstream.
The check whether quota format is set even though there are no
quota files with journalled quota is pointless and it actually
makes it impossible to turn off journalled quotas (as there's
no way to unset journalled quota format). Just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 064d83892e upstream.
Free the buffer head if the journal descriptor block fails checksum
verification.
This is the jbd2 port of the e2fsprogs patch "e2fsck: free bh on csum
verify error in do_one_pass".
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a0626e7595 upstream.
When loading extended attributes, check each entry's value offset to
make sure it doesn't collide with the entries.
Without this check it is easy to crash the kernel by mounting a
malicious FS containing a file with an EA wherein e_value_offs = 0 and
e_value_size > 0 and then deleting the EA, which corrupts the name
list.
(See the f_ea_value_crash test's FS image in e2fsprogs for an example.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit abe5f97291 upstream.
The zone allocation batches can easily underflow due to higher-order
allocations or spills to remote nodes. On SMP that's fine, because
underflows are expected from concurrency and dealt with by returning 0.
But on UP, zone_page_state will just return a wrapped unsigned long,
which will get past the <= 0 check and then consider the zone eligible
until its watermarks are hit.
Commit 3a025760fc ("mm: page_alloc: spill to remote nodes before
waking kswapd") already made the counter-resetting use
atomic_long_read() to accomodate underflows from remote spills, but it
didn't go all the way with it.
Make it clear that these batches are expected to go negative regardless
of concurrency, and use atomic_long_read() everywhere.
Fixes: 81c0a2bb51 ("mm: page_alloc: fair zone allocator policy")
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ luis: backported to 3.16 by Johannes Weiner ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2f3169fb18 upstream.
Commit 65b38851a1
("NFS: Fix /proc/fs/nfsfs/servers and /proc/fs/nfsfs/volumes")
updated the following function:
static int nfs_volume_list_open(struct inode *inode, struct file *file)
it used &nfs_server_list_ops instead of &nfs_volume_list_ops
which means cat /proc/fs/nfsfs/volumes = /proc/fs/nfsfs/servers
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Fixes: 65b38851a1 (NFS: Fix /proc/fs/nfsfs/servers and...)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 65b38851a1 upstream.
The usage of pid_ns->child_reaper->nsproxy->net_ns in
nfs_server_list_open and nfs_client_list_open is not safe.
/proc for a pid namespace can remain mounted after the all of the
process in that pid namespace have exited. There are also times
before the initial process in a pid namespace has started or after the
initial process in a pid namespace has exited where
pid_ns->child_reaper can be NULL or stale. Making the idiom
pid_ns->child_reaper->nsproxy a double whammy of problems.
Luckily all that needs to happen is to move /proc/fs/nfsfs/servers and
/proc/fs/nfsfs/volumes under /proc/net to /proc/net/nfsfs/servers and
/proc/net/nfsfs/volumes and add a symlink from the original location,
and to use seq_open_net as it has been designed.
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a968bed78b upstream.
Unlike the clocks management code for runtime PM, the code used for
system suspend does not check the pm_clock_entry.status field.
If pm_clk_acquire() failed, ce->status will be PCE_STATUS_ERROR, and
ce->clk will be a negative error code (e.g. 0xfffffffe = -2 = -ENOENT).
Depending on the clock implementation, suspend or resume may crash with:
Unable to handle kernel NULL pointer dereference at virtual address 00000026
(CCF clk_disable() has an IS_ERR_OR_NULL() check, while CCF clk_enable()
only has a NULL check; pre-CCF implementations may behave differently)
While just checking for PCE_STATUS_ERROR would be sufficient, it doesn't
hurt to use the same state machine as is done for runtime PM, as this
makes the two versions more similar, and eligible for a future
consolidation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2c4e3dbf63 upstream.
When __usb_find_phy_dev() does not return error and
try_module_get() fails, return -ENODEV.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2c80929c4c upstream.
The third argument of fuse_get_user_pages() "nbytesp" refers to the number of
bytes a caller asked to pack into fuse request. This value may be lesser
than capacity of fuse request or iov_iter. So fuse_get_user_pages() must
ensure that *nbytesp won't grow.
Now, when helper iov_iter_get_pages() performs all hard work of extracting
pages from iov_iter, it can be done by passing properly calculated
"maxsize" to the helper.
The other caller of iov_iter_get_pages() (dio_refill_pages()) doesn't need
this capability, so pass LONG_MAX as the maxsize argument here.
Fixes: c9c37e2e63 ("fuse: switch to iov_iter_get_pages()")
Reported-by: Werner Baumann <werner.baumann@onlinehome.de>
Tested-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2d08713969 upstream.
Since the conversion of objtree to use relative pathnames (commit
7e1c04779e, "kbuild: Use relative path for $(objtree)"), the debug
info files have been ending up in /debian/dbgtmp/ in the regular
linux-image package instead of the debug files package. Fix up the
paths so that the debug files end up in the -dbg package.
This is based on a similar patch by Darrick.
Reported-and-tested-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b478e336b3 upstream.
The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().
To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: matwey.kornilov@gmail.com
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[ Upstream commit 06090e8ed8 ]
It is not sufficient to only implement get_user_pages_fast(), you
must also implement the atomic version __get_user_pages_fast()
otherwise you end up using the weak symbol fallback implementation
which simply returns zero.
This is dangerous, because it causes the futex code to loop forever
if transparent hugepages are supported (see get_futex_key()).
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
