The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve readability by creating a define for each microphone detection
level.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
GRO/GSO layers can be enabled on a node, even if said
node is only forwarding packets.
This patch permits GSO (and upcoming GRO) support for GRE
encapsulated packets, even if the host has no GRE tunnel setup.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This API can be used by drivers to send their custom
configuration using SET_CONFIG NCI command to the device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers require special configuration while initializing.
This patch adds setup handler for this custom configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking fixes from David Miller:
"I'm hoping this is the very last batch of networking fixes for 3.13,
here goes nothing:
1) Fix crashes in VLAN's header_ops passthru.
2) Bridge multicast code needs to use BH spinlocks to prevent
deadlocks with timers. From Curt Brune.
3) ipv6 tunnels lack proper synchornization when updating percpu
statistics. From Li RongQing.
4) Fixes to bnx2x driver from Yaniv Rosner, Dmitry Kravkov and Michal
Kalderon.
5) Avoid undefined operator evaluation order in llc code, from Daniel
Borkmann.
6) Error paths in various GSO offload paths do not unwind properly,
in particular they must undo any modifications they have made to
the SKB. From Wei-Chun Chao.
7) Fix RX refill races during restore in virtio-net, from Jason Wang.
8) Fix SKB use after free in LLC code, from Daniel Borkmann.
9) Missing unlock and OOPS in netpoll code when VLAN tag handling
fails.
10) Fix vxlan device attachment wrt ipv6, from Fan Du.
11) Don't allow creating infiniband links to non-infiniband devices,
from Hangbin Liu.
12) Revert FEC phy reset active low change, it breaks things. From
Fabio Estevam.
13) Fix header pointer handling in 6lowpan header building code, from
Daniel Borkmann.
14) Fix RSS handling in be2net driver, from Vasundhara Volam.
15) Fix modem port indexing in HSO driver, from Dan Williams"
* http://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
bridge: use spin_lock_bh() in br_multicast_set_hash_max
ipv6: don't install anycast address for /128 addresses on routers
hso: fix handling of modem port SERIAL_STATE notifications
isdn: Drop big endian cpp checks from telespci and hfc_pci drivers
be2net: fix max_evt_qs calculation for BE3 in SR-IOV config
be2net: increase the timeout value for loopback-test FW cmd
be2net: disable RSS when number of RXQs is reduced to 1 via set-channels
xen-netback: Include header for vmalloc
net: 6lowpan: fix lowpan_header_create non-compression memcpy call
fec: Revert "fec: Do not assume that PHY reset is active low"
bnx2x: fix VLAN configuration for VFs.
bnx2x: fix AFEX memory overflow
bnx2x: Clean before update RSS arrives
bnx2x: Correct number of MSI-X vectors for VFs
bnx2x: limit number of interrupt vectors for 57711
qlcnic: Fix bug in Tx completion path
infiniband: make sure the src net is infiniband when create new link
{vxlan, inet6} Mark vxlan_dev flags with VXLAN_F_IPV6 properly
cxgb4: allow large buffer size to have page size
netpoll: Fix missing TXQ unlock and and OOPS.
...
Drop user features if an outdated user space instance that does not
understand the concept of user_features attempted to create a new
datapath.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Allocates a new sk_buff large enough to cover the specified payload
plus required Netlink headers. Will check receiving socket for
memory mapped i/o capability and use it if enabled. Will fall back
to non-mapped skb if message size exceeds the frame size of the ring.
Signed-of-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP out_of_order_queue lock is not used, as queue manipulation
happens with socket lock held and we therefore use the lockless
skb queue routines (as __skb_queue_head())
We can use __skb_queue_head_init() instead of skb_queue_head_init()
to make this more consistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SDIO identifier for Broadcom WLAN devices were defined in the
brcmfmac SDIO driver. Moving the definitions in MMC header file
seems common sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Proportional Integral controller Enhanced (PIE) is a scheduler to address the
bufferbloat problem.
>From the IETF draft below:
" Bufferbloat is a phenomenon where excess buffers in the network cause high
latency and jitter. As more and more interactive applications (e.g. voice over
IP, real time video streaming and financial transactions) run in the Internet,
high latency and jitter degrade application performance. There is a pressing
need to design intelligent queue management schemes that can control latency and
jitter; and hence provide desirable quality of service to users.
We present here a lightweight design, PIE(Proportional Integral controller
Enhanced) that can effectively control the average queueing latency to a target
value. Simulation results, theoretical analysis and Linux testbed results have
shown that PIE can ensure low latency and achieve high link utilization under
various congestion situations. The design does not require per-packet
timestamp, so it incurs very small overhead and is simple enough to implement
in both hardware and software. "
Many thanks to Dave Taht for extensive feedback, reviews, testing and
suggestions. Thanks also to Stephen Hemminger and Eric Dumazet for reviews and
suggestions. Naeem Khademi and Dave Taht independently contributed to ECN
support.
For more information, please see technical paper about PIE in the IEEE
Conference on High Performance Switching and Routing 2013. A copy of the paper
can be found at ftp://ftpeng.cisco.com/pie/.
Please also refer to the IETF draft submission at
http://tools.ietf.org/html/draft-pan-tsvwg-pie-00
All relevant code, documents and test scripts and results can be found at
ftp://ftpeng.cisco.com/pie/.
For problems with the iproute2/tc or Linux kernel code, please contact Vijay
Subramanian (vijaynsu@cisco.com or subramanian.vijay@gmail.com) Mythili Prabhu
(mysuryan@cisco.com)
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Mythili Prabhu <mysuryan@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says: <pablo@netfilter.org>
====================
nftables updates for net-next
The following patchset contains nftables updates for your net-next tree,
they are:
* Add set operation to the meta expression by means of the select_ops()
infrastructure, this allows us to set the packet mark among other things.
From Arturo Borrero Gonzalez.
* Fix wrong format in sscanf in nf_tables_set_alloc_name(), from Daniel
Borkmann.
* Add new queue expression to nf_tables. These comes with two previous patches
to prepare this new feature, one to add mask in nf_tables_core to
evaluate the queue verdict appropriately and another to refactor common
code with xt_NFQUEUE, from Eric Leblond.
* Do not hide nftables from Kconfig if nfnetlink is not enabled, also from
Eric Leblond.
* Add the reject expression to nf_tables, this adds the missing TCP RST
support. It comes with an initial patch to refactor common code with
xt_NFQUEUE, again from Eric Leblond.
* Remove an unused variable assignment in nf_tables_dump_set(), from Michal
Nazarewicz.
* Remove the nft_meta_target code, now that Arturo added the set operation
to the meta expression, from me.
* Add help information for nf_tables to Kconfig, also from me.
* Allow to dump all sets by specifying NFPROTO_UNSPEC, similar feature is
available to other nf_tables objects, requested by Arturo, from me.
* Expose the table usage counter, so we can know how many chains are using
this table without dumping the list of chains, from Tomasz Bursztyka.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SD0 may operate in low-voltage mode, with a minimum of 0.41V
and a maximum of 1.5V. This is indicated by bit 4 of FUSE7.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
broonie.e6264@m.evernote.com
Signed-off-by: Mark Brown <broonie@linaro.org>
PVH allows PV linux guest to utilize hardware extended capabilities,
such as running MMU updates in a HVM container.
The Xen side defines PVH as (from docs/misc/pvh-readme.txt,
with modifications):
"* the guest uses auto translate:
- p2m is managed by Xen
- pagetables are owned by the guest
- mmu_update hypercall not available
* it uses event callback and not vlapic emulation,
* IDT is native, so set_trap_table hcall is also N/A for a PVH guest.
For a full list of hcalls supported for PVH, see pvh_hypercall64_table
in arch/x86/hvm/hvm.c in xen. From the ABI prespective, it's mostly a
PV guest with auto translate, although it does use hvm_op for setting
callback vector."
Use .ascii and .asciz to define xen feature string. Note, the PVH
string must be in a single line (not multiple lines with \) to keep the
assembler from putting null char after each string before \.
This patch allows it to be configured and enabled.
We also use introduce the 'XEN_ELFNOTE_SUPPORTED_FEATURES' ELF note to
tell the hypervisor that 'hvm_callback_vector' is what the kernel
needs. We can not put it in 'XEN_ELFNOTE_FEATURES' as older hypervisor
parse fields they don't understand as errors and refuse to load
the kernel. This work-around fixes the problem.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The 'xen_hvm_resume_frames' used to be an 'unsigned long'
and contain the virtual address of the grants. That was OK
for most architectures (PVHVM, ARM) were the grants are contiguous
in memory. That however is not the case for PVH - in which case
we will have to do a lookup for each virtual address for the PFN.
Instead of doing that, lets make it a structure which will contain
the array of PFNs, the virtual address and the count of said PFNs.
Also provide a generic functions: gnttab_setup_auto_xlat_frames and
gnttab_free_auto_xlat_frames to populate said structure with
appropriate values for PVHVM and ARM.
To round it off, change the name from 'xen_hvm_resume_frames' to
a more descriptive one - 'xen_auto_xlat_grant_frames'.
For PVH, in patch "xen/pvh: Piggyback on PVHVM for grant driver"
we will populate the 'xen_auto_xlat_grant_frames' by ourselves.
v2 moves the xen_remap in the gnttab_setup_auto_xlat_frames
and also introduces xen_unmap for gnttab_free_auto_xlat_frames.
Suggested-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v3: Based on top of 'asm/xen/page.h: remove redundant semicolon']
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Which is a PV guest with auto page translation enabled
and with vector callback. It is a cross between PVHVM and PV.
The Xen side defines PVH as (from docs/misc/pvh-readme.txt,
with modifications):
"* the guest uses auto translate:
- p2m is managed by Xen
- pagetables are owned by the guest
- mmu_update hypercall not available
* it uses event callback and not vlapic emulation,
* IDT is native, so set_trap_table hcall is also N/A for a PVH guest.
For a full list of hcalls supported for PVH, see pvh_hypercall64_table
in arch/x86/hvm/hvm.c in xen. From the ABI prespective, it's mostly a
PV guest with auto translate, although it does use hvm_op for setting
callback vector."
Also we use the PV cpuid, albeit we can use the HVM (native) cpuid.
However, we do have a fair bit of filtering in the xen_cpuid and
we can piggyback on that until the hypervisor/toolstack filters
the appropiate cpuids. Once that is done we can swap over to
use the native one.
We setup a Kconfig entry that is disabled by default and
cannot be enabled.
Note that on ARM the concept of PVH is non-existent. As Ian
put it: "an ARM guest is neither PV nor HVM nor PVHVM.
It's a bit like PVH but is different also (it's further towards
the H end of the spectrum than even PVH).". As such these
options (PVHVM, PVH) are never enabled nor seen on ARM
compilations.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add xen_irq_set_priority() to set an event channels priority. This function
will only work with event channel ABIs that support priority (i.e., the
FIFO-based ABI).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Add the hypercall sub-ops and the structures for the shared data used
in the FIFO-based event channel ABI.
The design document for this new ABI is available here:
http://xenbits.xen.org/people/dvrabel/event-channels-H.pdf
In summary, events are reported using a per-domain shared event array
of event words. Each event word has PENDING, LINKED and MASKED bits
and a LINK field for pointing to the next event in the event queue.
There are 16 event queues (with different priorities) per-VCPU.
Key advantages of this new ABI include:
- Support for over 100,000 events (2^17).
- 16 different event priorities.
- Improved fairness in event latency through the use of FIFOs.
The ABI is available in Xen 4.4 and later.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Remove the check during unbind for NR_EVENT_CHANNELS as this limits
support to less than 4096 ports.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
In preparation for alternative event channel ABIs, move all the
functions accessing the shared data structures into their own file.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.
Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).
In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The comment about return value of acpi_table_parse() is incorrect.
This patch fix it.
Since all callers only check if the function succeeded or not, this
patch simplifies the semantics by returning -errno for all failure
cases. This will also simply the comment.
As suggested by Toshi Kani <toshi.kani@hp.com>, also change the stub
in linux/acpi.h to return -ENODEV.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a inline_data recovery routine with the following policy.
[prev.] [next] of inline_data flag
o o -> recover inline_data
o x -> remove inline_data, and then recover data blocks
x o -> remove inline_data, and then recover inline_data
x x -> recover data blocks
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
macvlan needs vlan_pcpu_stats so make it visible even if compiling
without VLAN_8021Q support. Otherwise a very long compiler error happens.
Fixes: cdf3e274cf ("macvlan: unify macvlan_pcpu_stats and vlan_pcpu_stats")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-By: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several drivers making use of ACPI _DSM method to detect
and invoke device specific methods. Currently every driver has
implemented its private version to support ACPI _DSM method.
So this patch introduces three helper functions to support ACPI _DSM
method, which will be used to replace open-coded versions.
It helps to simplify code and improve code readability.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we don't use SNDRV_PCM_RATE_xxx bit fields for sample rate, we need to
change the description to an array for describing the sample rates supported by
the sink/source
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
