Add the bindings that describe a GOcontroll Moduline module slot. This
slot provides all the interfaces to interface with a Moduline compatible
IO module. The actual module is not reasonable to describe as it can be
swapped at will, with this connector the driver will be able to probe
for a module on boot.
The connector consists of 2 parts, one part for interfacing with the SoC
and main board, the other part has 13 IO channels for the module to
interact with the outside world. The functions of these IO channels are
determined by the type of module in the slot. The IO on the SoC side is
as follows:
- a 3v3 supply, this tends to be the logic level of the module and its
microcontroller
- a 5v0 supply, this can be used to power low power peripherals on the
module
- a 6v-8v supply, this can be used for high power peripherals on the
module
- a 6v-30v supply, this tends to be a dirty supply that comes from the
controller supply after some circuit protection, or is the same as
the 6v-8v supply.
- an SPI bus which carries the communication between the SoC and the
microcontroller on the module.
- an I2C bus shared between the SoC and all module slots which can
carry direct module-to-module communication.
- a reset line
- an interrupt line that indicates a clear to transmit signal
- a sync line shared between the SoC and all module slots which could
be used to synchronize modules for time sensitive IO spread across
modules.
- a SMBus alert line that is shared between the modules but is not
connected to the SoC so that is ignored.
A slot-number property is used to identify the physical location of a
module slot. Without it, it would be impossible to identify which module
to control if there are multiple of one type, to address the desired IO.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Link: https://patch.msgid.link/20250226-initial_display-v2-3-23fafa130817@gocontroll.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GOcontroll produces embedded linux systems and IO modules to use in
these systems, add its prefix.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Link: https://patch.msgid.link/20250226-initial_display-v2-2-23fafa130817@gocontroll.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The former code sets the V slot from inside set_bitwidth according to
the bitwidth of the PCM format. That's wrong, since:
* It overrides the V slot parsed from DT binding.
* The V slot is set shifted behind the I slot by the length of the PCM
bitwidth, but the PCM bitwidth has no assured relation to the TDM
slot width.
Replace the former logic by setting up the I/V sense transmission only
in case of both I/V slots being specified in devicetree, and never
override those values. In case the slots are left unspecified, disable
the transmission completely.
There's an improbable case someone is relying on the old behavior, but
if so, that's a setup that only works by accident, and cannot be sanely
supported going forward. There's no indication anyone is consuming the
I/V sense data up to today, so break the former behavior.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-6-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new explicit function for the setting of I/V sense TDM slots.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-5-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add control to expose the option of autoretry behavior on overcurrent
events in the codec.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-4-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SN012776 is a speaker amp chip found in Apple's 2021 laptops. It appears
similar and more-or-less compatible to TAS2764. Extend the TAS2764
driver with some SN012776 specifics and configure the chip assuming
it's in one of the Apple machines.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-3-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A variant of TAS2770 known as TAS5770L is found in Apple Silicon Macs.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-2-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI SN012776 is a variant of TAS2764 found in Apple Silicon Macs.
It continues Apple's long-standing policy of getting vendors to
spin out subtly incompatible and Apple-exclusive variants of their
publicly available parts.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-1-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for
device node") uses __free(device_node) for dlc->of_node, but we need to
keep it while driver is in use.
Don't use __free(device_node) in graph_util_parse_dai().
Fixes: 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for device node")
Reported-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Reported-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Tested-by: Detlev Casanova <detlev.casanova@collabora.com>
Link: https://patch.msgid.link/87eczisyhh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Xiaomi Redmi Note 8 based on the SM6125 SoC.
Defined features:
- dmesg output to bootloader preconfigured display
- USB
- eMMC
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
Link: https://lore.kernel.org/r/20250311003353.8250-3-semfault@disroot.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Xiaomi Redmi Note 8 (codenamed ginkgo),
which is based off the SM6125 SoC.
Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250311003353.8250-2-semfault@disroot.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Decoder and encoder nodes are already deprecated from bindings. Update
the venus node to align with bindings. The nodes were deprecated with
commit 459997e899 ("media: dt-bindings: qcom-venus: Deprecate
video-decoder and video-encoder where applicable") and is part of
v6.14-rc1 and onwards.
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250303-b4-media-v2-1-893651a4b1c7@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add CTCU and ETR nodes in DT to enable related functionalities.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jie Gan <quic_jiegan@quicinc.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250303032931.2500935-11-quic_jiegan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
If qcom_ssc_block_bus_pds_enable() fails, the previous call to
qcom_ssc_block_bus_pds_attach() must be undone, as already done in the
remove function.
In order to do that, move the code related to the power domains management
to the end of the function, in order to avoid many changes in all the error
handling path that would need to go through the new error handling path.
Fixes: 97d485edc1 ("bus: add driver for initializing the SSC bus on (some) qcom SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1b89ec7438c9a893c09083e8591772c8ad3cb599.1740932040.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
reg_mpm_sscaon_config[01] are allocated with devm_ioremap_resource(). So,
they will be unmapped automatically by the manage resource framework.
Remove the incorrect explicit iounmap() calls from the remove function.
Fixes: 97d485edc1 ("bus: add driver for initializing the SSC bus on (some) qcom SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/efd06711b126e761a06eb5ef82daf9ad4e116a10.1740932040.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Audio DSP supports compressed playback on this SoC. It is required
to add compressed DAI and separate MultimeMedia DAI link to enable this.
Fcplay or cplay tools from tinycompress can playback, say, mp3 files:
fcplay -c 0 -d 3 test.mp3
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://lore.kernel.org/r/20250228162308.388818-1-alexey.klimov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PMUs shares the same per-cpu (PPI) interrupt, so declare the proper
interrupt partition maps and use the 4th interrupt cell to pass the
partition phandle for each ARM PMU node.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250228-topic-sm8650-pmu-ppi-partition-v4-2-78cffd35c73d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The ARM PMUs shares the same per-cpu (PPI) interrupt, so we need to switch
to interrupt-cells = <4> in the GIC node to allow adding an interrupt
partition map phandle as the 4th cell value for GIC_PPI interrupts.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250228-topic-sm8650-pmu-ppi-partition-v4-1-78cffd35c73d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Radxa E20C may come with an onboard eMMC (8GB / 16GB / 32GB / 64GB).
Enable support for the onboard eMMC on Radxa E20C.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250305214108.1327208-4-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SDHCI controller in Rockchip RK3528 is similar to the one included
in RK3588.
Add device tree node for the SDHCI controller in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250305214108.1327208-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the thermal sensor (tsens) on the MSM8960 by copying and
modifying the relevant nodes from the APQ8064 dtsi. These changes enable
thermal management.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250227-expressatt-tsens-v4-2-d70afa5a1fd0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The qcs615 SoC has a True Random Number Generator, add the node
with the correct compatible set.
Signed-off-by: Abhinaba Rakshit <quic_arakshit@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250228-enable-trng-for-qcs615-v2-2-017aa858576e@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Bluetooth node described in the device tree is actually on an M.2
slot. What module is present depends on what the end user installed,
and should be left to an overlay.
Remove the existing bluetooth node. This gets rid of bogus timeout
errors.
Fixes: 8cf890aabd ("arm64: dts: rockchip: Add nodes for SDIO/UART Wi-Fi/Bluetooth modules to Radxa Rock 3A")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250220165051.1889055-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
0x0 to 0xf0000000 are SDRAM memory areas where 0x10f000 is located.
So move the SHMEM memory of arm_scmi to the reserved memory node.
Fixes: a3adc0b907 ("arm64: dts: rockchip: add core dtsi for RK3568 SoC")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20250308100001.572657-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SM8750 have two different clusters. cluster0 have CPU 0-5 as child and
cluster1 have CPU 6-7 as child. Each cluster requires its own idle state
and power domain in order to achieve complete domain sleep state.
However only single cluster idle state is added mapping CPU 0-7 to the
same power domain. Fix this by correctly mapping each CPU to respective
cluster power domain and make cluster1 power domain use same domain idle
state as cluster0 since both use same idle state parameters.
Fixes: 068c3d3c83 ("arm64: dts: qcom: Add base SM8750 dtsi")
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250226-sm8750_cluster_idle-v2-1-ef0ac81e242f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the Qualcomm SM8450 platform the second PCIe host can be used
either as an RC or as an EP device. Add device node for the PCIe EP.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-8-61a0fdfb75b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the Qualcomm AR2 Gen1 platform the second PCIe host can be used
either as an RC or as an EP device. Add device node for the PCIe EP.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-7-61a0fdfb75b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the QCM6490 boards, the LPASS firmware controls the complete clock
controller functionalities and associated power domains. However, only
the LPASS resets required to be controlled by the high level OS. Thus,
add support for the resets in the clock driver to enable the Audio SW
driver to assert/deassert the audio resets as needed.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-2-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the QCM6490 boards, the LPASS firmware controls the complete clock
controller functionalities and associated power domains. However, only
the LPASS resets required to be controlled by the high level OS. Thus,
add the new QCM6490 compatible to support the reset functionality for
Low Power Audio subsystem.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-1-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The `tx-sched-sp` property was removed in commit aed6864035 ("net:
stmmac: platform: Delete a redundant condition branch").
Therefore, it can be safely removed from the device tree.
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250218125157.412701-1-prabhakar.csengg@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Jason Xing says:
====================
Introduce bpf_sol_tcp_getsockopt() helper.
Add bpf_getsockopt for RTO MIN and DELACK MAX.
Add corresponding selftests for bpf.
====================
Link: https://patch.msgid.link/20250312153523.9860-1-kerneljasonxing@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Add missing compatibles and pdm_domain_data for SDM630 and SDM636.
Unlike their older brother (SDM660) these two cut down SoCs lack CDSP.
Other protection domains are the same as the ones for SDM660.
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250217050251.298163-1-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Copy bam nodes from qcom-ipq8064.dtsi and change
the reg values to match msm8960.
Co-developed-by: Sam Day <me@samcday.com>
Signed-off-by: Sam Day <me@samcday.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rudraksha Gupta <guptarud@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250213-expressatt-bam-v3-1-0ff338f488b2@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During the GDSC FSM state, the GDSC hardware waits for an ACK from the
respective subsystem core. In some scenarios, this ACK can be delayed.
To handle such delays, increase the GDSC status poll timeout from 1500us
to 2000us as per the design recommendation.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Imran Shaik <quic_imrashai@quicinc.com>
Tested-by: Imran Shaik <quic_imrashai@quicinc.com> # on QCS8300
Link: https://lore.kernel.org/r/20250214-gdsc_fixes-v1-2-73e56d68a80f@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the retain_ff_enable bit of GDSCR only if the GDSC is already ON.
Once the GDSCR moves to HW control, SW no longer can determine the state
of the GDSCR and setting the retain_ff bit could destroy all the register
contents we intended to save.
Therefore, move the retain_ff configuration before switching the GDSC to
HW trigger mode.
Cc: stable@vger.kernel.org
Fixes: 173722995c ("clk: qcom: gdsc: Add support to enable retention of GSDCR")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Imran Shaik <quic_imrashai@quicinc.com>
Tested-by: Imran Shaik <quic_imrashai@quicinc.com> # on QCS8300
Link: https://lore.kernel.org/r/20250214-gdsc_fixes-v1-1-73e56d68a80f@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add PWM/LPG node to the PM8937 dtsi so devices
which use this block can enable them.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250213-pm8937-pwm-v2-2-49ea59801a33@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Architecturally we have two filters for each regular event counter,
so add generic support for the second one too.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Link: https://lore.kernel.org/r/b11be3f23a72bc27088b115099c8fe865b70babc.1741190362.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The notion of a single u32 filter value for any event doesn't scale well
when the potential architectural scope is already two 64-bit values, and
implementations may add custom stuff on the side too. Rather than try to
thread arbitrary filter data through the common path, let's just make
the set_ev_filter op self-contained in terms of parsing and configuring
any and all filtering for the given event - splitting out a distinct op
for cycles events which inherently differ - and let implementations
override the whole thing if they want to do something different. This
already allows the Ampere code to stop looking a bit hacky.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Link: https://lore.kernel.org/r/c0cd4d4c12566dbf1b062ccd60241b3e0639f4cc.1741190362.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Implementations may occasionally want to refer to register offsets, so
for the sake of consistency move all of the register definitions to join
the PMIIDR fields in the private header where they can be shared. As an
example nicety, we can then define Ampere's imp-def filters in terms of
the architectural PMIMPDEF range rather than open-coded offsets.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Link: https://lore.kernel.org/r/5a3c796560665b51cb63fec0d473afd8f8d0a836.1741190362.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The MSI interrupt numbers of the PCIe3 controller are incorrect. Due
to this, the functional bring up of the QDSP6 processor on the PCIe
endpoint has failed. Correct the MSI interrupt numbers to properly
bring up the QDSP6 processor on the PCIe endpoint.
Fixes: d80c7fbfa9 ("arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes")
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250313071422.510-1-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The patch refactors a bit on supporting getsockopt for TCP BPF flags.
For now, only TCP_BPF_SOCK_OPS_CB_FLAGS. Later, more flags will be added
into this function.
No functional changes here.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250312153523.9860-2-kerneljasonxing@gmail.com
