This report will feedback some basic information from firmware(PTA counter,
report counter, mailbox counter etc). And the report version need to match
driver & firmware both side. The original logic break the switch case logic
before driver update the report version. It made the report can not be
parsed correctly. Delete the break at the version 7 and 8.
Add logic to count C2H event report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-3-pkshih@realtek.com
Some of 11ax AP set the UL HE-SIG-A2 reserved subfield to all 0s, which
will cause the 11be chip to recognize trigger frame as EHT. We propose
a method to bypass the "UL HE-SIG-A2 reserved subfield" and always uses
HE TB in response to the AP's trigger frame.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-6-pkshih@realtek.com
The 8922A now supports dynamic antenna gain. However, in firmware
before v0.35.64.0, different transmit powers cannot be applied to
each RF path. To comply with regulatory limits in these older
firmware, the lower of the two requested transmit powers will
be used for both paths when they differ.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-5-pkshih@realtek.com
The dynamic antenna gain (DAG) considers the country, meaning DAG can
be activated only when countries and regulatory domains allow it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-4-pkshih@realtek.com
TAS state switching mechanism now incorporates the TX ratio as a
decision parameter. The average power calculation has been improved
by using a higher resolution conversion from dBm to linear. During
scan or MCC operations, TAS state is forced to static SAR and
suspend the average power calculation. Additionally, TAS window
size depends on the regulatory domain and band to ensure compliance.
TAS is enabled when permitted by the regulatory domain and is
currently supported on the 8852CE.
For debugging, add a flag to disable_dm that can stop TAS mechanism.
Co-developed-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-3-pkshih@realtek.com
Enhanced the dBm to linear conversion function to accommodate negative
dBm values and improved the precision from 1 dBm to 0.25 dBm.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-2-pkshih@realtek.com
test_and_{set,clear}_bit are fully ordered as specified in
Documentation/atomic_bitops.txt. Fix incorrect comment stating otherwise.
Note that the implementation is correct since commit
9347ce54cd ("RISC-V: __test_and_op_bit_ord should be strongly ordered")
was introduced.
Signed-off-by: Ignacio Encinas <ignacio@iencinas.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
There is a type bug because the return statement:
return ret < 0 ? ret : recv_cnt;
The issue is that ret is an int, recv_cnt is a u32 and the function
returns ssize_t, which is a signed long. The way that the type promotion
works is that the negative error codes are first cast to u32 and then
to signed long. The error codes end up being positive instead of
negative and the callers treat them as success.
Fixes: 81cc7e51c4 ("drm/mediatek: Allow commands to be sent during video mode")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202412210801.iADw0oIH-lkp@intel.com/
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/b754a408-4f39-4e37-b52d-7706c132e27f@stanley.mountain/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DPI is part of the display / multimedia block in MediaTek SoCs, and
always have a power-domain (at least in the upstream device-trees).
Add the power-domains property to the binding example.
Fixes: 9273cf7d39 ("dt-bindings: display: mediatek: convert the dpi bindings to yaml")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231023-display-support-v7-1-6703f3e26831@baylibre.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The function mtk_dp_wait_hpd_asserted() may be called before the
`mtk_dp->drm_dev` pointer is assigned in mtk_dp_bridge_attach().
Specifically it can be called via this callpath:
- mtk_edp_wait_hpd_asserted
- [panel probe]
- dp_aux_ep_probe
Using "drm" level prints anywhere in this callpath causes a NULL
pointer dereference. Change the error message directly in
mtk_dp_wait_hpd_asserted() to dev_err() to avoid this. Also change the
error messages in mtk_dp_parse_capabilities(), which is called by
mtk_dp_wait_hpd_asserted().
While touching these prints, also add the error code to them to make
future debugging easier.
Fixes: 7eacba9a08 ("drm/mediatek: dp: Add .wait_hpd_asserted() for AUX bus")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250116094249.1.I29b0b621abb613ddc70ab4996426a3909e1aa75f@changeid/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
When CONFIG_MTK_CMDQ is enabled, if the display is controlled by the CPU
while other hardware is controlled by the GCE, the display will encounter
a mbox request channel failure.
However, it will still enter the CONFIG_MTK_CMDQ statement, causing the
config_updating flag to never be set to false. As a result, no page flip
event is sent back to user space, and the screen does not update.
Fixes: da03801ad0 ("drm/mediatek: Move mtk_crtc_finish_page_flip() to ddp_cmdq_cb()")
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250224051301.3538484-1-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Following a recent discussion at last Plumbers, John Stultz, Sumit
Sewal, TJ Mercier and I came to an agreement that we should document
what the dma-buf heaps names are expected to be, and what the buffers
attributes you'll get should be documented.
Let's create that doc to make sure those attributes and names are
guaranteed going forward.
Reviewed-by: T.J. Mercier <tjmercier@google.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250306135114.1943738-1-mripard@kernel.org
For now, it is time to remove -fno-jump-tables to enable jump table for
objtool if the compiler has -mannotate-tablejump, otherwise it is better
to remain -fno-jump-tables to keep compatibility with older compilers.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20241217010905.13054-8-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The objtool program need to analysis the control flow of each object file
generated by compiler toolchain, it needs to know all the locations that
a branch instruction may jump into, if a jump table is used, objtool has
to correlate the jump instruction with the table.
On x86 (which is the only port supported by objtool before LoongArch),
there is a relocation type on the jump instruction and directly points
to the table. But on LoongArch, the relocation is on another kind of
instruction prior to the jump instruction, and also with scheduling it
is not very easy to tell the offset of that instruction from the jump
instruction. Furthermore, because LoongArch has -fsection-anchors (often
enabled at -O1 or above) the relocation may actually points to a section
anchor instead of the table itself.
For the jump table of switch cases, a GCC patch "LoongArch: Add support
to annotate tablejump" and a Clang patch "[LoongArch] Add options for
annotate tablejump" have been merged into the upstream mainline, it can
parse the additional section ".discard.tablejump_annotate" which stores
the jump info as pairs of addresses, each pair contains the address of
jump instruction and the address of jump table.
For the jump table of computed gotos, it is indeed not easy to implement
in the compiler, especially if there is more than one computed goto in a
function such as ___bpf_prog_run(). objdump kernel/bpf/core.o shows that
there are many table jump instructions in ___bpf_prog_run(), but there are
no relocations on the table jump instructions and to the table directly on
LoongArch.
Without the help of compiler, in order to figure out the address of goto
table for the special case of ___bpf_prog_run(), since the instruction
sequence is relatively single and stable, it makes sense to add a helper
find_reloc_of_rodata_c_jump_table() to find the relocation which points
to the section ".rodata..c_jump_table".
If find_reloc_by_table_annotate() failed, it means there is no relocation
info of switch table address in ".rela.discard.tablejump_annotate", then
objtool may find the relocation info of goto table ".rodata..c_jump_table"
with find_reloc_of_rodata_c_jump_table().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20250211115016.26913-6-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The objtool program need to analysis the control flow of each object file
generated by compiler toolchain, it needs to know all the locations that
a branch instruction may jump into, if a jump table is used, objtool has
to correlate the jump instruction with the table.
On x86 (which is the only port supported by objtool before LoongArch),
there is a relocation type on the jump instruction and directly points
to the table. But on LoongArch, the relocation is on another kind of
instruction prior to the jump instruction, and also with scheduling it
is not very easy to tell the offset of that instruction from the jump
instruction. Furthermore, because LoongArch has -fsection-anchors (often
enabled at -O1 or above) the relocation may actually points to a section
anchor instead of the table itself.
The good news is that after continuous analysis and discussion, at last
a GCC patch "LoongArch: Add support to annotate tablejump" and a Clang
patch "[LoongArch] Add options for annotate tablejump" have been merged
into the upstream mainline, the compiler changes make life much easier
for switch table support of objtool on LoongArch.
By now, there is an additional section ".discard.tablejump_annotate" to
store the jump info as pairs of addresses, each pair contains the address
of jump instruction and the address of jump table.
In order to find switch table, it is easy to parse the relocation section
".rela.discard.tablejump_annotate" to get table_sec and table_offset, the
rest process is somehow like x86.
Additionally, it needs to get each table size. When compiling on LoongArch,
there are unsorted table offsets of rodata if there exist many jump tables,
it will get the wrong table end and find the wrong table jump destination
instructions in add_jump_table().
Sort the rodata table offset by parsing ".rela.discard.tablejump_annotate"
and then get each table size of rodata corresponded with each table jump
instruction, it is used to check the table end and will break the process
when parsing ".rela.rodata" to avoid getting the wrong jump destination
instructions.
Link: https://gcc.gnu.org/git/?p=gcc.git;a=commit;h=0ee028f55640
Link: 4c2c177567
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20250211115016.26913-5-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
For the most part, an absolute relocation type is used for rodata.
In the case of STT_SECTION, reloc->sym->offset is always zero, for
the other symbol types, reloc_addend(reloc) is always zero, thus it
can use a simple statement "reloc->sym->offset + reloc_addend(reloc)"
to obtain the symbol offset for various symbol types.
When compiling on LoongArch, there exist PC relative relocation types
for rodata, it needs to calculate the symbol offset with "S + A - PC"
according to the spec of "ELF for the LoongArch Architecture".
If there is only one jump table in the rodata, the "PC" is the entry
address which is equal with the value of reloc_offset(reloc), at this
time, reloc_offset(table) is 0.
If there are many jump tables in the rodata, the "PC" is the offset
of the jump table's base address which is equal with the value of
reloc_offset(reloc) - reloc_offset(table).
So for LoongArch, if the relocation type is PC relative, it can use a
statement "reloc_offset(reloc) - reloc_offset(table)" to get the "PC"
value when calculating the symbol offset with "S + A - PC" for one or
many jump tables in the rodata.
Add an arch-specific function arch_jump_table_sym_offset() to assign
the symbol offset, for the most part that is an absolute relocation,
the default value is "reloc->sym->offset + reloc_addend(reloc)" in
the weak definition, it can be overridden by each architecture that
has different requirements.
Link: https://github.com/loongson/la-abi-specs/blob/release/laelf.adoc
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20250211115016.26913-4-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In the most cases, the entry size of rodata is 8 bytes because the
relocation type is 64 bit. There are also 32 bit relocation types,
the entry size of rodata should be 4 bytes in this case.
Add an arch-specific function arch_reloc_size() to assign the entry
size of rodata for x86, powerpc and LoongArch.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20250211115016.26913-3-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In the relocation section ".rela.rodata" of each .o file compiled with
LoongArch toolchain, there are various symbol types such as STT_NOTYPE,
STT_OBJECT, STT_FUNC in addition to the usual STT_SECTION, it needs to
use reloc symbol offset instead of reloc addend to find the destination
instruction in find_jump_table() and add_jump_table().
For the most part, an absolute relocation type is used for rodata. In the
case of STT_SECTION, reloc->sym->offset is always zero, and for the other
symbol types, reloc_addend(reloc) is always zero, thus it can use a simple
statement "reloc->sym->offset + reloc_addend(reloc)" to obtain the symbol
offset for various symbol types.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20250211115016.26913-2-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The check for using old libelf prints an error message when libelf.h is
not available but does not abort. This may confuse so hide the compiler
error message.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Link: https://lore.kernel.org/r/20250203073610.206000-1-david.engraf@sysgo.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Commit fb12098d8e ("docs: submit-checklist: Allow creating
cross-references for ABI README") assumes that the path of
"Documentation/ABI/README" would be converted to a cross-ref to
the README.
However, as the README is included by the "kernel-abi" directive
at Documentation/admin-guide/abi.rst, the expected conversion
does not happen.
Instead, use the path where the "kernel-abi" directive exists for
the conversion to work. Restore the original path of README in
inline-literal form as an additional note for readers of the .rst
file.
Apply the same changes for translations.
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Fixes: fb12098d8e ("docs: submit-checklist: Allow creating cross-references for ABI README")
Fixes: eb0c714120 ("docs: translations: Allow creating cross-references for ABI README")
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Alex Shi <alexs@kernel.org>
Cc: Yanteng Si <si.yanteng@linux.dev>
Cc: Dongliang Mu <dzm91@hust.edu.cn>
Cc: Hu Haowen <2023002089@link.tyut.edu.cn>
Cc: Federico Vaga <federico.vaga@vaga.pv.it>
Cc: Carlos Bilbao <carlos.bilbao@kernel.org>
Cc: Avadhut Naik <avadhut.naik@amd.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250304075734.56660-1-akiyks@gmail.com
Ammend missing "install" operation keyword after "apt-get", and fix
"build-essentials" to "build-essential".
Signed-off-by: I Hsin Cheng <richard120310@gmail.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250306030708.8133-1-richard120310@gmail.com
Updates the document to clearly describe the scope and role the TAB plays
in making decisions on unresolved violations. If and when the CoC has to
make a call on instituting a ban, it doesn't act without the TAB's approval
and only when the TAB approves it with 2/3 vote in favor of the measure.
These changes ensure that the TAB role and its oversight on CoC measures
is consistently described throughout the document.
Fixes: c818d5c64c ("Documentation/CoC: spell out enforcement for unacceptable behaviors")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250306211231.13154-1-shuah@kernel.org
Both get_feat.pl and list-arch.sh use uname -m to get the machine hardware
name to figure out the current architecture if no architecture is specified
with a command line option.
This doesn't work for s390, since for 64 bit kernels the hardware name is
s390x, while the architecture name within the kernel, as well as in all
feature files is s390.
Therefore substitute s390x with s390 similar to what is already done for
x86_64 and i386.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250312155219.3597768-1-hca@linux.ibm.com
Add nodes for the CDSP and its SMP2P. These are compatible with earlier
SM8650 with difference in one more interrupt.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250312-b4-sm8750-cdsp-v4-1-4925d607cea6@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add LPASS macro codecs and LPASS TLMM pin controller on Qualcomm SM8750
for proper sound support. These are fully compatible with earlier SM8550.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250312-sm8750-audio-v3-2-40fbb3e53f95@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for IPCC mailbox, SMP2P for ADSP, AOSS and the ADSP remoteproc
PAS loader (compatible with SM8550).
Reviewed-by: Melody Olvera <quic_molvera@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250312-sm8750-audio-v3-1-40fbb3e53f95@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
BPF schedulers could trigger a crash by passing in an invalid CPU to the
helper scx_bpf_select_cpu_dfl(). Fix it by verifying input validity.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCZ9H4tw4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGY2PAP95rqNEACvl5uz/HQM+T0WpwGDaIJ3fmKYd3GZY
3XJjhwD/YmKMLmth0xeDLkAtVUNsMp4EjpssKdzi0CJq+Nl4nQw=
=OxEw
-----END PGP SIGNATURE-----
Merge tag 'sched_ext-for-6.14-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fix from Tejun Heo:
"BPF schedulers could trigger a crash by passing in an invalid CPU to
the scx_bpf_select_cpu_dfl() helper.
Fix it by verifying input validity"
* tag 'sched_ext-for-6.14-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Validate prev_cpu in scx_bpf_select_cpu_dfl()
A couple of driver specific fixes, an error handling fix for the Atmel
QuadSPI driver and a fix for a nasty synchronisation issue in the data
path for the Microchip driver which affects larger transfers.
There's also a MAINTAINERS update for the Samsung driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmfRlUIACgkQJNaLcl1U
h9B51wf/VMJhNbybxH1pGHIBrFq+xzwjozmY/Hk+omw9VTIIFto6Hejq3HkOoKOO
T62drvGqxWpHq/reqiLF4TDRD0KSiOjD/KM+xXzbn5F73P5j5tTR4Zo1OLFOPiWj
Tqs1TiJbQllHCynmfJjB9EAsAembqOMClybW3yvG0XObHgONiBMaDAyFwqbHFwRi
b0YFqyEdLUoLK4WvuPMpn4hspEJg8D0MsKTURityx0LgpWO03zhqC5qn9DSn/0jI
cNKT1veCt+vS1YDsZ5UQLsfWfLYj9d3JArfg5T7kBtwq21ZHve/uqyzceUfufo4G
QAAFKqgk5J5c6G79Q5oo/PYD7vkdUQ==
=e3ZQ
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes, an error handling fix for the Atmel
QuadSPI driver and a fix for a nasty synchronisation issue in the data
path for the Microchip driver which affects larger transfers.
There's also a MAINTAINERS update for the Samsung driver"
* tag 'spi-fix-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: microchip-core: prevent RX overflows when transmit size > FIFO size
MAINTAINERS: add tambarus as R for Samsung SPI
spi: atmel-quadspi: remove references to runtime PM on error path
All Qualcomm firmwares uploaded to linux-firmware are in MBN format,
instead of split MDT. Firmware for boards here is not yet in
linux-firmware, but if it gets accepted it will be MBN, not MDT.
Change might affect users of DTS which rely on manually placed firmware
files, not coming from linux-firmware package.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250108120530.156928-1-krzysztof.kozlowski@linaro.org
[bjorn: Updated subject]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Don't error out on large MTU if XDP is multi-buf.
The ping test now tests ping with XDP and high MTU.
netdevsim doesn't actually run the prog (yet?) so
it doesn't matter if the prog was multi-buf..
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20250311092820.542148-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow userspace to write the safe (NI) value for ID_AA64MMFR0_EL1.TGRAN*_2.
Disallow to change these fields for NV since kvm provides a sanitized view
for them based on the PAGE_SIZE.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Link: https://lore.kernel.org/kvmarm/20250306184013.30008-1-sebott@redhat.com/
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Stanislav Fomichev says:
====================
net: remove rtnl_lock from the callers of queue APIs
All drivers that use queue management APIs already depend on the netdev
lock. Ultimately, we want to have most of the paths that work with
specific netdev to be rtnl_lock-free (ethtool mostly in particular).
Queue API currently has a much smaller API surface, so start with
rtnl_lock from it:
- add mutex to each dmabuf binding (to replace rtnl_lock)
- move netdev lock management to the callers of netdev_rx_queue_restart
and drop rtnl_lock
====================
Link: https://patch.msgid.link/20250311144026.4154277-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers that use queue API are already converted to use
netdev instance lock. Move netdev instance lock management to
the netlink layer and drop rtnl_lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry. <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-4-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As we move away from rtnl_lock for queue ops, introduce
per-netdev_nl_sock lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No functional changes. Next patches will add more granular locking
to netdev_nl_sock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
for_each_possible_cpu() is currently used to initialize cpuidle
in below cpuidle drivers:
drivers/cpuidle/cpuidle-arm.c
drivers/cpuidle/cpuidle-big_little.c
drivers/cpuidle/cpuidle-psci.c
drivers/cpuidle/cpuidle-qcom-spm.c
drivers/cpuidle/cpuidle-riscv-sbi.c
However, in cpu_dev_register_generic(), for_each_present_cpu()
is used to register CPU devices which means the CPU devices are
only registered for present CPUs and not all possible CPUs.
With nosmp or maxcpus=0, only the boot CPU is present, lead
to the failure:
| Failed to register cpuidle device for cpu1
Then rollback to cancel all CPUs' cpuidle registration.
Change for_each_possible_cpu() to for_each_present_cpu() in the
above cpuidle drivers to ensure it only registers cpuidle devices
for CPUs that are actually present.
Fixes: b0c69e1214 ("drivers: base: Use present CPUs in GENERIC_CPU_DEVICES")
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250307145547.2784821-1-ping.bai@nxp.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
