Add helper functions that SDCA drivers can use to calculate the
properties of SDCA Controls (registers) specified through DisCo.
Most of these are fairly obvious from the SDCA Access Modes.
DisCo Constants, values which are specified in the ACPI rather than on
the device, are handled as unreadable and unwritable registers. The
intention is these will be populated in the register defaults table
allowing drivers to read them normally. This means the drivers can be
agnostic as to which values are DisCo Constants.
Finally, support for SDCA Dual Ranked Controls is currently limited
here, at the moment the current value will be used directly. Writing
the current value directly is valid as per the specification
although the synchronicity of updates across multiple registers is
lost. Support for this will probably need to be added later. But its a
fairly hard problem and doesn't need to be solved immediately.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250217140159.2288784-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The defaults array in regcache must be sorted into ascending register
address order, because binary search is used to locate values in
the array. Add a helper to sort the register defaults array which
can be useful for systems that dynamically create a defaults array
based on external information.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20250217140159.2288784-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexander Lobakin says:
====================
bpf: cpumap: enable GRO for XDP_PASS frames
Several months ago, I had been looking through my old XDP hints tree[0]
to check whether some patches not directly related to hints can be sent
standalone. Roughly at the same time, Daniel appeared and asked[1] about
GRO for cpumap from that tree.
Currently, cpumap uses its own kthread which processes cpumap-redirected
frames by batches of 8, without any weighting (but with rescheduling
points). The resulting skbs get passed to the stack via
netif_receive_skb_list(), which means no GRO happens.
Even though we can't currently pass checksum status from the drivers,
in many cases GRO performs better than the listified Rx without the
aggregation, confirmed by tests.
In order to enable GRO in cpumap, we need to do the following:
* patches 1-2: decouple the GRO struct from the NAPI struct and allow
using it out of a NAPI entity within the kernel core code;
* patch 3: switch cpumap from netif_receive_skb_list() to
gro_receive_skb().
Additional improvements:
* patch 4: optimize XDP_PASS in cpumap by using arrays instead of linked
lists;
* patch 5-6: introduce and use function do get skbs from the NAPI percpu
caches by bulks, not one at a time;
* patch 7-8: use that function in veth as well and remove the one that
was now superseded by it.
My trafficgen UDP GRO tests, small frame sizes:
GRO off GRO on
baseline 2.7 N/A Mpps
patch 3 2.3 4 Mpps
patch 8 2.4 4.7 Mpps
1...3 diff -17 +48 %
1...8 diff -11 +74 %
Daniel reported from +14%[2] to +18%[3] of throughput in neper's TCP RR
tests. On my system however, the same test gave me up to +100%.
Note that there's a series from Lorenzo[4] which achieves the same, but
in a different way. During the discussions, the approach using a
standalone GRO instance was preferred over the threaded NAPI.
[0] https://github.com/alobakin/linux/tree/xdp_hints
[1] https://lore.kernel.org/bpf/cadda351-6e93-4568-ba26-21a760bf9a57@app.fastmail.com
[2] https://lore.kernel.org/bpf/merfatcdvwpx2lj4j2pahhwp4vihstpidws3jwljwazhh76xkd@t5vsh4gvk4mh
[3] https://lore.kernel.org/bpf/yzda66wro5twmzpmjoxvy4si5zvkehlmgtpi6brheek3sj73tj@o7kd6nurr3o6
[4] https://lore.kernel.org/bpf/20241130-cpumap-gro-v1-0-c1180b1b5758@kernel.org
====================
Link: https://patch.msgid.link/20250225171751.2268401-1-aleksander.lobakin@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The only user was veth, which now uses napi_skb_cache_get_bulk().
It's now preferred over a direct allocation and is exported as
well, so remove this one.
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that we can bulk-allocate skbs from the NAPI cache, use that
function to do that in veth as well instead of direct allocation from
the kmem caches. veth uses NAPI and GRO, so this is both context-safe
and beneficial.
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that cpumap uses GRO, which drops unused skb heads to the NAPI
cache, use napi_skb_cache_get_bulk() to try to reuse cached entries
and lower MM layer pressure. Always disable the BH before checking and
running the cpumap-pinned XDP prog and don't re-enable it in between
that and allocating an skb bulk, as we can access the NAPI caches only
from the BH context.
The better GRO aggregates packets, the less new skbs will be allocated.
If an aggregated skb contains 16 frags, this means 15 skbs were returned
to the cache, so next 15 skbs will be built without allocating anything.
The same trafficgen UDP GRO test now shows:
GRO off GRO on
threaded GRO 2.3 4 Mpps
thr bulk GRO 2.4 4.7 Mpps
diff +4 +17 %
Comparing to the baseline cpumap:
baseline 2.7 N/A Mpps
thr bulk GRO 2.4 4.7 Mpps
diff -11 +74 %
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a function to get an array of skbs from the NAPI percpu cache.
It's supposed to be a drop-in replacement for
kmem_cache_alloc_bulk(skbuff_head_cache, GFP_ATOMIC) and
xdp_alloc_skb_bulk(GFP_ATOMIC). The difference (apart from the
requirement to call it only from the BH) is that it tries to use
as many NAPI cache entries for skbs as possible, and allocate new
ones only if needed.
The logic is as follows:
* there is enough skbs in the cache: decache them and return to the
caller;
* not enough: try refilling the cache first. If there is now enough
skbs, return;
* still not enough: try allocating skbs directly to the output array
with %GFP_ZERO, maybe we'll be able to get some. If there's now
enough, return;
* still not enough: return as many as we were able to obtain.
Most of times, if called from the NAPI polling loop, the first one will
be true, sometimes (rarely) the second one. The third and the fourth --
only under heavy memory pressure.
It can save significant amounts of CPU cycles if there are GRO cycles
and/or Tx completion cycles (anything that descends to
napi_skb_cache_put()) happening on this CPU.
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
cpumap still uses linked lists to store a list of skbs to pass to the
stack. Now that we don't use listified Rx in favor of
napi_gro_receive(), linked list is now an unneeded overhead.
Inside the polling loop, we already have an array of skbs. Let's reuse
it for skbs passed to cpumap (generic XDP) and keep there in case of
XDP_PASS when a program is installed to the map itself. Don't list
regular xdp_frames after converting them to skbs as well; store them
in the mentioned array (but *before* generic skbs as the latters have
lower priority) and call gro_receive_skb() for each array element after
they're done.
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
cpumap has its own BH context based on kthread. It has a sane batch
size of 8 frames per one cycle.
GRO can be used here on its own. Adjust cpumap calls to the upper stack
to use GRO API instead of netif_receive_skb_list() which processes skbs
by batches, but doesn't involve GRO layer at all.
In plenty of tests, GRO performs better than listed receiving even
given that it has to calculate full frame checksums on the CPU.
As GRO passes the skbs to the upper stack in the batches of
@gro_normal_batch, i.e. 8 by default, and skb->dev points to the
device where the frame comes from, it is enough to disable GRO
netdev feature on it to completely restore the original behaviour:
untouched frames will be being bulked and passed to the upper stack
by 8, as it was with netif_receive_skb_list().
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make GRO init and cleanup functions global to be able to use GRO
without a NAPI instance. Taking into account already global gro_flush(),
it's now fully usable standalone.
New functions are not exported, since they're not supposed to be used
outside of the kernel core code.
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In fact, these two are not tied closely to each other. The only
requirements to GRO are to use it in the BH context and have some
sane limits on the packet batches, e.g. NAPI has a limit of its
budget (64/8/etc.).
Move purely GRO fields into a new structure, &gro_node. Embed it
into &napi_struct and adjust all the references.
gro_node::cached_napi_id is effectively the same as
napi_struct::napi_id, but to be used on GRO hotpath to mark skbs.
napi_struct::napi_id is now a fully control path field.
Three Ethernet drivers use napi_gro_flush() not really meant to be
exported, so move it to <net/gro.h> and add that include there.
napi_gro_receive() is used in more than 100 drivers, keep it
in <linux/netdevice.h>.
This does not make GRO ready to use outside of the NAPI context
yet.
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Refactor parity calculations to use the standard parity8() helper. This
change eliminates redundant implementations and improves code
efficiency.
[ ubizjak: Updated the patch to apply to the latest x86 tree. ]
Co-developed-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20250227125616.2253774-1-ubizjak@gmail.com
Building with W=1 shows a warning about xge_acpi_match being unused when
CONFIG_ACPI is disabled:
drivers/net/ethernet/apm/xgene-v2/main.c:723:36: error: unused variable 'xge_acpi_match' [-Werror,-Wunused-const-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250225163341.4168238-2-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Building with W=1 shows a warning about hns_mdio_acpi_match being unused when
CONFIG_ACPI is disabled:
drivers/net/ethernet/hisilicon/hns_mdio.c:631:36: error: unused variable 'hns_mdio_acpi_match' [-Werror,-Wunused-const-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20250225163341.4168238-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Because calls to get_this_hybrid_cpu_type() and
get_this_hybrid_cpu_native_id() are not required now. cpu-type and
native-model-id are cached at boot in per-cpu struct cpuinfo_topology.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-add-cpu-type-v5-4-2ae010f50370@linux.intel.com
get_this_hybrid_cpu_type() misses a case when cpu-type is populated
regardless of X86_FEATURE_HYBRID_CPU. This is particularly true for hybrid
variants that have P or E cores fused off.
Instead use the cpu-type cached in struct x86_topology, as it does not rely
on hybrid feature to enumerate cpu-type. This can also help avoid the
model-specific fixup get_hybrid_cpu_type(). Also replace the
get_this_hybrid_cpu_native_id() with its cached value in struct
x86_topology.
While at it, remove enum hybrid_cpu_type as it serves no purpose when we
have the exact cpu-types defined in enum intel_cpu_type. Also rename
atom_native_id to intel_native_id and move it to intel-family.h where
intel_cpu_type lives.
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-add-cpu-type-v5-3-2ae010f50370@linux.intel.com
Intel pstate driver relies on SMP calls to get the cpu-type of a given CPU.
Remove the SMP calls and instead use the cached value of cpu-type which is
more efficient.
[ mingo: Forward ported it. ]
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-add-cpu-type-v5-2-2ae010f50370@linux.intel.com
The hex values in CPU debug interface are not prefixed with 0x. This may
cause misinterpretation of values. Fix it.
[ mingo: Restore previous vertical alignment of the output. ]
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-add-cpu-type-v5-1-2ae010f50370@linux.intel.com
Older Exynos designs, like Exynos5422, do not have USB Type-C and the
USB DRD PHY does not really need CONFIG_TYPEC for these devices at all.
Incorrectly added optional dependency on CONFIG_TYPEC caused this driver
to be missing for exynos_defconfig and as result Exynos5422-based boards
like Hardkernel Odroid HC1 failed to probe USB.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Closes: https://krzk.eu/#/builders/21/builds/6139
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/3c0b77e6-357d-453e-8b63-4757c3231bde@samsung.com/
Fixes: 09dc674295 ("phy: exynos5-usbdrd: subscribe to orientation notifier if required")
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250227070518.5468-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
HDMI audio is available on the Rock 5B HDMI TX ports.
Enable it for both ports.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-4-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
For hdmi0_sound, use the simple-audio-card driver with the hdmi0 QP node
as CODEC and the i2s5 device as CPU.
Similarly for hdmi1_sound, the CODEC is the hdmi1 node and the CPU is
i2s6, but only added in the rk3588-extra.dtsi device tree as the second
TX HDMI port is not available on base versions of the SoC.
The simple-audio-card,mclk-fs value is set to 128 as it is done in
the downstream driver.
The #sound-dai-cells value is set to 0 in the hdmi0 and hdmi1 nodes so
that they can be used as audio codec nodes.
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3588 Tiger Haikou
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-3-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT changes to enable the second HDMI output port on
Rockchip RK3588 EVB1.
While at it, switch the position of &vop_mmu and @vop to maintain the
alphabetical order.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-5-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
The HDMI1 PHY PLL clock source cannot be added directly to vop node in
rk3588-base.dtsi, along with the HDMI0 related one, because HDMI1 is an
optional feature and its PHY node belongs to a separate (extra) DT file.
Therefore, add the HDMI1 PHY PLL clock source to VOP2 by overwriting its
clocks & clock-names properties in the extra DT file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-4-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI1 PHY.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-3-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When extra warnings are enable, there are configurations that build
pktgen without CONFIG_XFRM, which leaves a static const variable unused:
net/core/pktgen.c:213:1: error: unused variable 'F_IPSEC' [-Werror,-Wunused-const-variable]
213 | PKT_FLAGS
| ^~~~~~~~~
net/core/pktgen.c:197:2: note: expanded from macro 'PKT_FLAGS'
197 | pf(IPSEC) /* ipsec on for flows */ \
| ^~~~~~~~~
This could be marked as __maybe_unused, or by making the one use visible
to the compiler by slightly rearranging the #ifdef blocks. The second
variant looks slightly nicer here, so use that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Seiderer <ps.report@gmx.net>
Link: https://patch.msgid.link/20250225085722.469868-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We applied a fix for a KASAN issue for snd_pcm_format_set_silence(),
and it introduced a NULL check of pat. But this turned out to be
utterly superfluous; it points to pcm_formats[].silence, and this is
an array, which can be never NULL.
The problem (supposedly) it tried to address at that time was likely
already fixed by another commit 8423f0b6d5 ("ALSA: pcm: oss: Fix
race at SNDCTL_DSP_SYNC") instead.
So let's drop the superfluous NULL check again. While we're at it,
keep the whitespace fix and move the pat assignment after the width
check for a bit better code readability.
Fixes: 2f7a26abb8 ("ALSA: pcm: Test for "silence" field in struct "pcm_format_data"")
Link: https://patch.msgid.link/20250227095150.8187-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
Introduce Morello fvp dts.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-10-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
Introduce Morello SoC dts.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-9-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
The Morello Platform (soc) and the Fixed Virtual Platfom (fvp) share
some functionalities that have conveniently been included in
morello.dtsi to avoid duplication.
Introduce morello.dtsi.
Note: Morello fvp will be introduced with a future patch series.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-8-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Replace drm_err() calls in vop2_bind() and vop2_create_crtcs() with
dev_err_probe(), to simplify error handling and improve consistency.
Additionally, ensure the already existing dev_err_probe() invocations
pass drm->dev instead of dev as their first argument, so that we get the
actual reason in case of -EPROBE_DEFER errors:
platform display-subsystem: deferred probe pending: (reason unknown)
vs.
platform display-subsystem: deferred probe pending: rockchip-drm: <actual reason>
While at it, add the missing '\n' to some of the message strings.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250223-vop2-hdmi1-disp-modes-v2-2-f4cec5e06fbe@collabora.com
The RK3588 specific implementation is currently quite limited in terms
of handling the full range of display modes supported by the connected
screens, e.g. 2560x1440@75Hz, 2048x1152@60Hz, 1024x768@60Hz are just a
few of them.
Additionally, it doesn't cope well with non-integer refresh rates like
59.94, 29.97, 23.98, etc.
Make use of HDMI1 PHY PLL as a more accurate DCLK source to handle
all display modes up to 4K@60Hz.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250223-vop2-hdmi1-disp-modes-v2-1-f4cec5e06fbe@collabora.com
There are two main modifications: one is expanding struct
rockchip_dp_chip_data to an array, and the other is adding
&rockchip_dp_chip_data.reg to separate different edp devices.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250224081325.96724-3-damon.ding@rock-chips.com
Register the dw-hdmi-qp bridge driver as an HDMI audio codec.
The register values computation functions (for n) are based on the
downstream driver, as well as the register writing functions.
The driver uses the generic HDMI Codec framework in order to implement
the HDMI audio support.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217215641.372723-2-detlev.casanova@collabora.com
Pull in the VFS changes shared with xfs for making RWF_DONTCACHE work
with buffered writes for xfs.
Signed-off-by: Christian Brauner <brauner@kernel.org>
Read side was already fully supported, and with the write side
appropriately punted to the worker queue, all that's needed now is
setting FOP_DONTCACHE in the file_operations structure to enable full
support for read and write uncached IO.
This provides similar benefits to using RWF_DONTCACHE with reads. Testing
buffered writes on 32 files:
writing bs 65536, uncached 0
1s: 196035MB/sec
2s: 132308MB/sec
3s: 132438MB/sec
4s: 116528MB/sec
5s: 103898MB/sec
6s: 108893MB/sec
7s: 99678MB/sec
8s: 106545MB/sec
9s: 106826MB/sec
10s: 101544MB/sec
11s: 111044MB/sec
12s: 124257MB/sec
13s: 116031MB/sec
14s: 114540MB/sec
15s: 115011MB/sec
16s: 115260MB/sec
17s: 116068MB/sec
18s: 116096MB/sec
where it's quite obvious where the page cache filled, and performance
dropped from to about half of where it started, settling in at around
115GB/sec. Meanwhile, 32 kswapds were running full steam trying to
reclaim pages.
Running the same test with uncached buffered writes:
writing bs 65536, uncached 1
1s: 198974MB/sec
2s: 189618MB/sec
3s: 193601MB/sec
4s: 188582MB/sec
5s: 193487MB/sec
6s: 188341MB/sec
7s: 194325MB/sec
8s: 188114MB/sec
9s: 192740MB/sec
10s: 189206MB/sec
11s: 193442MB/sec
12s: 189659MB/sec
13s: 191732MB/sec
14s: 190701MB/sec
15s: 191789MB/sec
16s: 191259MB/sec
17s: 190613MB/sec
18s: 191951MB/sec
and the behavior is fully predictable, performing the same throughout
even after the page cache would otherwise have fully filled with dirty
data. It's also about 65% faster, and using half the CPU of the system
compared to the normal buffered write.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20250204184047.356762-3-axboe@kernel.dk
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add iomap buffered write support for RWF_DONTCACHE. If RWF_DONTCACHE is
set for a write, mark the folios being written as uncached. Then
writeback completion will drop the pages. The write_iter handler simply
kicks off writeback for the pages, and writeback completion will take
care of the rest.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20250204184047.356762-2-axboe@kernel.dk
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Temporarily allow the creation of zero length files in efivarfs so the
'fwupd' user space firmware update tool can continue to operate. This
hack should be reverted as soon as the fwupd mechanisms for updating
firmware have been fixed.
fwupd has been coded to open a firmware file, close it, remove the
immutable bit and write to it. Since commit 908af31f48 ("efivarfs:
fix error on write to new variable leaving remnants") this behaviour
results in the first close removing the file which causes the second
write to fail. To allow fwupd to keep working code up an indicator of
size 1 if a write fails and only remove the file on that condition (so
create at zero size is allowed).
Tested-by: Richard Hughes <richard@hughsie.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[ardb: replace LVFS with fwupd, as suggested by Richard]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
