Enable launch time (Time-Based Scheduling) support for XDP zero copy via
the XDP Tx metadata framework.
This patch has been tested with tools/testing/selftests/bpf/xdp_hw_metadata
on Intel Tiger Lake platform. Below are the test steps and result.
Test 1: Send a single packet with the launch time set to 1 s in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo ./xdp_hw_metadata enp0s30f4 -l 1000000000 -L 1
2. On the Link Partner, send a UDP packet with VLAN priority 1 to port 9091
of the DUT.
Result:
When the launch time is set to 1 s in the future, the delta between the
launch time and the transmit hardware timestamp is 16.963 us, as shown in
printout of the xdp_hw_metadata application below.
0x55b5864717a8: rx_desc[4]->addr=88100 addr=88100 comp_addr=88100 EoP
No rx_hash, err=-95
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to User RX-time sec:0.0004 (375.624 usec)
XDP RX-time: 1734579065768004454 (sec:1734579065.7680)
delta to User RX-time sec:0.0001 (88.498 usec)
No rx_vlan_tci or rx_vlan_proto, err=-95
0x55b5864717a8: ping-pong with csum=5619 (want 0000)
csum_start=34 csum_offset=6
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to HW Launch-time sec:1.0000 (1000000.000 usec)
0x55b5864717a8: complete tx idx=4 addr=4018
HW Launch-time: 1734579066767717328 (sec:1734579066.7677)
delta to HW TX-complete-time sec:0.0000 (16.963 usec)
HW TX-complete-time: 1734579066767734291 (sec:1734579066.7677)
delta to User TX-complete-time sec:0.0001
(130.408 usec)
XDP RX-time: 1734579065768004454 (sec:1734579065.7680)
delta to User TX-complete-time sec:0.9999
(999860.245 usec)
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to HW TX-complete-time sec:1.0000 (1000016.963 usec)
0x55b5864717a8: complete rx idx=132 addr=88100
Test 2: Send 1000 packets with a 10 ms interval and the launch time set to
500 us in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo chrt -f 99 ./xdp_hw_metadata enp0s30f4 -l 500000 -L 1 > \
/dev/shm/result.log
2. On the Link Partner, send 1000 UDP packets with a 10 ms interval and
VLAN priority 1 to port 9091 of the DUT.
Result:
When the launch time is set to 500 us in the future, the average delta
between the launch time and the transmit hardware timestamp is 13.854 us,
as shown in the analysis of /dev/shm/result.log below. The XDP launch time
works correctly in sending 1000 packets continuously.
Min delta: 08.410 us
Avr delta: 13.854 us
Max delta: 17.076 us
Total packets forwarded: 1000
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250216093430.957880-4-yoong.siang.song@intel.com
Add launch time hardware offload request to xdp_hw_metadata. Users can
configure the delta of launch time relative to HW RX-time using the "-l"
argument. By default, the delta is set to 0 ns, which means the launch time
is disabled. By setting the delta to a non-zero value, the launch time
hardware offload feature will be enabled and requested. Additionally, users
can configure the Tx Queue to be enabled with the launch time hardware
offload using the "-L" argument. By default, Tx Queue 0 will be used.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250216093430.957880-3-yoong.siang.song@intel.com
Extend the XDP Tx metadata framework so that user can requests launch time
hardware offload, where the Ethernet device will schedule the packet for
transmission at a pre-determined time called launch time. The value of
launch time is communicated from user space to Ethernet driver via
launch_time field of struct xsk_tx_metadata.
Suggested-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250216093430.957880-2-yoong.siang.song@intel.com
Add ethtool support to configure the IRQ coalescing behavior. Support
separate timers for Rx and Tx for time based coalescing. For frame based
configuration, currently we only support the Rx side.
The hardware allows configuration of descriptor count instead of frame
count requiring conversion between the two. We assume 2 descriptors
per frame, one for the metadata and one for the data segment.
When rx-frames are not configured, we set the RX descriptor count to
half the ring size as a fail safe.
Default configuration:
ethtool -c eth0 | grep -E "rx-usecs:|tx-usecs:|rx-frames:"
rx-usecs: 30
rx-frames: 0
tx-usecs: 35
IRQ rate test:
With single iperf flow we monitor IRQ rate while changing the tx-usesc and
rx-usecs to high and low values.
ethtool -C eth0 rx-frames 8192 rx-usecs 150 tx-usecs 150
irq/sec 13k
irq/sec 14k
irq/sec 14k
ethtool -C eth0 rx-frames 8192 rx-usecs 10 tx-usecs 10
irq/sec 27k
irq/sec 28k
irq/sec 28k
Validating the use of extack:
ethtool -C eth0 rx-frames 16384
netlink error: fbnic: rx_frames is above device max
netlink error: Invalid argument
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250218023520.2038010-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the function get_ts_info and get_ts_stats in ethtool_ops to
get the HW capabilities and statistics for timestamping.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250218023432.146536-3-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jason Xing says:
====================
net-timestamp: bpf extension to equip applications transparently
"Timestamping is key to debugging network stack latency. With
SO_TIMESTAMPING, bugs that are otherwise incorrectly assumed to be
network issues can be attributed to the kernel." This is extracted
from the talk "SO_TIMESTAMPING: Powering Fleetwide RPC Monitoring"
addressed by Willem de Bruijn at netdevconf 0x17).
There are a few areas that need optimization with the consideration of
easier use and less performance impact, which I highlighted and mainly
discussed at netconf 2024 with Willem de Bruijn and John Fastabend:
uAPI compatibility, extra system call overhead, and the need for
application modification. I initially managed to solve these issues
by writing a kernel module that hooks various key functions. However,
this approach is not suitable for the next kernel release. Therefore,
a BPF extension was proposed. During recent period, Martin KaFai Lau
provides invaluable suggestions about BPF along the way. Many thanks
here!
This series adds the BPF networking timestamping infrastructure through
reusing most of the tx timestamping callback that is currently enabled
by the SO_TIMESTAMPING.. This series also adds TX timestamping support
for TCP. The RX timestamping and UDP support will be added in the future.
====================
Link: https://patch.msgid.link/20250220072940.99994-1-kerneljasonxing@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
BPF program calculates a couple of latency deltas between each tx
timestamping callbacks. It can be used in the real world to diagnose
the kernel behaviour in the tx path.
Check the safety issues by accessing a few bpf calls in
bpf_test_access_bpf_calls() which are implemented in the patch 3 and 4.
Check if the bpf timestamping can co-exist with socket timestamping.
There remains a few realistic things[1][2] to highlight:
1. in general a packet may pass through multiple qdiscs. For instance
with bonding or tunnel virtual devices in the egress path.
2. packets may be resent, in which case an ACK might precede a repeat
SCHED and SND.
3. erroneous or malicious peers may also just never send an ACK.
[1]: https://lore.kernel.org/all/67a389af981b0_14e0832949d@willemb.c.googlers.com.notmuch/
[2]: https://lore.kernel.org/all/c329a0c1-239b-4ca1-91f2-cb30b8dd2f6a@linux.dev/
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-13-kerneljasonxing@gmail.com
Add the bpf_sock_ops_enable_tx_tstamp kfunc to allow BPF programs to
selectively enable TX timestamping on a skb during tcp_sendmsg().
For example, BPF program will limit tracking X numbers of packets
and then will stop there instead of tracing all the sendmsgs of
matched flow all along. It would be helpful for users who cannot
afford to calculate latencies from every sendmsg call probably
due to the performance or storage space consideration.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-12-kerneljasonxing@gmail.com
This patch introduces a new callback in tcp_tx_timestamp() to correlate
tcp_sendmsg timestamp with timestamps from other tx timestamping
callbacks (e.g., SND/SW/ACK).
Without this patch, BPF program wouldn't know which timestamps belong
to which flow because of no socket lock protection. This new callback
is inserted in tcp_tx_timestamp() to address this issue because
tcp_tx_timestamp() still owns the same socket lock with
tcp_sendmsg_locked() in the meanwhile tcp_tx_timestamp() initializes
the timestamping related fields for the skb, especially tskey. The
tskey is the bridge to do the correlation.
For TCP, BPF program hooks the beginning of tcp_sendmsg_locked() and
then stores the sendmsg timestamp at the bpf_sk_storage, correlating
this timestamp with its tskey that are later used in other sending
timestamping callbacks.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-11-kerneljasonxing@gmail.com
Support the ACK case for bpf timestamping.
Add a new sock_ops callback, BPF_SOCK_OPS_TSTAMP_ACK_CB. This
callback will occur at the same timestamping point as the user
space's SCM_TSTAMP_ACK. The BPF program can use it to get the
same SCM_TSTAMP_ACK timestamp without modifying the user-space
application.
This patch extends txstamp_ack to two bits: 1 stands for
SO_TIMESTAMPING mode, 2 bpf extension.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-10-kerneljasonxing@gmail.com
Support hw SCM_TSTAMP_SND case for bpf timestamping.
Add a new sock_ops callback, BPF_SOCK_OPS_TSTAMP_SND_HW_CB. This
callback will occur at the same timestamping point as the user
space's hardware SCM_TSTAMP_SND. The BPF program can use it to
get the same SCM_TSTAMP_SND timestamp without modifying the
user-space application.
To avoid increasing the code complexity, replace SKBTX_HW_TSTAMP
with SKBTX_HW_TSTAMP_NOBPF instead of changing numerous callers
from driver side using SKBTX_HW_TSTAMP. The new definition of
SKBTX_HW_TSTAMP means the combination tests of socket timestamping
and bpf timestamping. After this patch, drivers can work under the
bpf timestamping.
Considering some drivers don't assign the skb with hardware
timestamp, this patch does the assignment and then BPF program
can acquire the hwstamp from skb directly.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-9-kerneljasonxing@gmail.com
Support sw SCM_TSTAMP_SND case for bpf timestamping.
Add a new sock_ops callback, BPF_SOCK_OPS_TSTAMP_SND_SW_CB. This
callback will occur at the same timestamping point as the user
space's software SCM_TSTAMP_SND. The BPF program can use it to
get the same SCM_TSTAMP_SND timestamp without modifying the
user-space application.
Based on this patch, BPF program will get the software
timestamp when the driver is ready to send the skb. In the
sebsequent patch, the hardware timestamp will be supported.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-8-kerneljasonxing@gmail.com
Support SCM_TSTAMP_SCHED case for bpf timestamping.
Add a new sock_ops callback, BPF_SOCK_OPS_TSTAMP_SCHED_CB. This
callback will occur at the same timestamping point as the user
space's SCM_TSTAMP_SCHED. The BPF program can use it to get the
same SCM_TSTAMP_SCHED timestamp without modifying the user-space
application.
A new SKBTX_BPF flag is added to mark skb_shinfo(skb)->tx_flags,
ensuring that the new BPF timestamping and the current user
space's SO_TIMESTAMPING do not interfere with each other.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-7-kerneljasonxing@gmail.com
No functional changes here. Only add test to see if the orig_skb
matches the usage of application SO_TIMESTAMPING.
In this series, bpf timestamping and previous socket timestamping
are implemented in the same function __skb_tstamp_tx(). To test
the socket enables socket timestamping feature, this function
skb_tstamp_tx_report_so_timestamping() is added.
In the next patch, another check for bpf timestamping feature
will be introduced just like the above report function, namely,
skb_tstamp_tx_report_bpf_timestamping(). Then users will be able
to know the socket enables either or both of features.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-6-kerneljasonxing@gmail.com
New TX timestamping sock_ops callbacks will be added in the
subsequent patch. Some of the existing BPF helpers will not
be safe to be used in the TX timestamping callbacks.
The bpf_sock_ops_setsockopt, bpf_sock_ops_getsockopt, and
bpf_sock_ops_cb_flags_set require owning the sock lock. TX
timestamping callbacks will not own the lock.
The bpf_sock_ops_load_hdr_opt needs the skb->data pointing
to the TCP header. This will not be true in the TX timestamping
callbacks.
At the beginning of these helpers, this patch checks the
bpf_sock->op to ensure these helpers are used by the existing
sock_ops callbacks only.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250220072940.99994-5-kerneljasonxing@gmail.com
The subsequent patch will implement BPF TX timestamping. It will
call the sockops BPF program without holding the sock lock.
This breaks the current assumption that all sock ops programs will
hold the sock lock. The sock's fields of the uapi's bpf_sock_ops
requires this assumption.
To address this, a new "u8 is_locked_tcp_sock;" field is added. This
patch sets it in the current sock_ops callbacks. The "is_fullsock"
test is then replaced by the "is_locked_tcp_sock" test during
sock_ops_convert_ctx_access().
The new TX timestamping callbacks added in the subsequent patch will
not have this set. This will prevent unsafe access from the new
timestamping callbacks.
Potentially, we could allow read-only access. However, this would
require identifying which callback is read-safe-only and also requires
additional BPF instruction rewrites in the covert_ctx. Since the BPF
program can always read everything from a socket (e.g., by using
bpf_core_cast), this patch keeps it simple and disables all read
and write access to any socket fields through the bpf_sock_ops
UAPI from the new TX timestamping callback.
Moreover, note that some of the fields in bpf_sock_ops are specific
to tcp_sock, and sock_ops currently only supports tcp_sock. In
the future, UDP timestamping will be added, which will also break
this assumption. The same idea used in this patch will be reused.
Considering that the current sock_ops only supports tcp_sock, the
variable is named is_locked_"tcp"_sock.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250220072940.99994-4-kerneljasonxing@gmail.com
This patch introduces a new bpf_skops_tx_timestamping() function
that prepares the "struct bpf_sock_ops" ctx and then executes the
sockops BPF program.
The subsequent patch will utilize bpf_skops_tx_timestamping() at
the existing TX timestamping kernel callbacks (__sk_tstamp_tx
specifically) to call the sockops BPF program. Later, four callback
points to report information to user space based on this patch will
be introduced.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250220072940.99994-3-kerneljasonxing@gmail.com
The new SK_BPF_CB_FLAGS and new SK_BPF_CB_TX_TIMESTAMPING are
added to bpf_get/setsockopt. The later patches will implement the
BPF networking timestamping. The BPF program will use
bpf_setsockopt(SK_BPF_CB_FLAGS, SK_BPF_CB_TX_TIMESTAMPING) to
enable the BPF networking timestamping on a socket.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250220072940.99994-2-kerneljasonxing@gmail.com
Ensure the FIFO is empty before issuing the DAA command to prevent
incorrect command data from being sent. Align with other data transfers,
such as svc_i3c_master_start_xfer_locked(), which flushes the FIFO before
sending a command.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250129162250.3629189-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
tun simply advances iov_iter when it needs to pad virtio header,
which leaves the garbage in the buffer as is. This will become
especially problematic when tun starts to allow enabling the hash
reporting feature; even if the feature is enabled, the packet may lack a
hash value and may contain a hole in the virtio header because the
packet arrived before the feature gets enabled or does not contain the
header fields to be hashed. If the hole is not filled with zero, it is
impossible to tell if the packet lacks a hash value.
In theory, a user of tun can fill the buffer with zero before calling
read() to avoid such a problem, but leaving the garbage in the buffer is
awkward anyway so replace advancing the iterator with writing zeros.
A user might have initialized the buffer to some non-zero value,
expecting tun to skip writing it. As this was never a documented
feature, this seems unlikely.
The overhead of filling the hole in the header is negligible when the
header size is specified according to the specification as doing so will
not make another cache line dirty under a reasonable assumption. Below
is a proof of this statement:
The first 10 bytes of the header is always written and tun also writes
the packet itself immediately after the packet unless the packet is
empty. This makes a hole between these writes whose size is: sz - 10
where sz is the specified header size.
Therefore, we will never make another cache line dirty when:
sz < L1_CACHE_BYTES + 10
where L1_CACHE_BYTES is the cache line size. Assuming
L1_CACHE_BYTES >= 16, this inequation holds when: sz < 26.
sz <= 20 according to the current specification so we even have a
margin of 5 bytes in case that the header size grows in a future version
of the specification.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Link: https://patch.msgid.link/20250215-buffers-v2-1-1fbc6aaf8ad6@daynix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the i2c_get/put_dma_safe_msg_buf for I2C transfers instead of using
the I3C-specific API.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250204091702.4014466-2-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The change is necessary to enable the use of the
`i2c_get_dma_safe_msg_buf()` API, which requires a non-const
`struct i2c_msg *` to operate. The `i2c_get_dma_safe_msg_buf()` function
ensures safe handling of I2C messages when using DMA, making it essential
for scenarios where DMA transfers are involved. By removing the `const`
qualifier, this patch allows drivers to prepare and manage DMA-safe
buffers directly.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250204091702.4014466-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Conor Culhane's email address (conor.culhane@silvaco.com) is no longer
accessible, and there has been no activity from him on
https://lore.kernel.org/linux-i3c/ in the past two years.
To avoid email delivery failure messages when sending patches to the I3C
mailing list, remove him from the Maintainers section and move him to the
credits.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250204161151.2179596-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The fix alone doesn't fix [1], but should be applied before debugging
that.
[1] https://syzkaller.appspot.com/bug?extid=38a0cbd267eff2d286ff
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
"nonce inconstancy" is popping up again, causing us to go emergency
read-only.
This one looks less serious, i.e. specific to the encryption path and
not indicative of a data corruption bug. But we'll need more info to
track it down.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The current code in dp_rx.h declares the ath12k_dp_rx_h_find_peer() twice.
Fix this by removing one of the redundant declarations of
ath12k_dp_rx_h_find_peer() to ensure that the function is declared only
once.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250219053640.223734-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Just a single fix to address the incorrect size of the Tx buffer in the
function scmi_imx_misc_ctrl_set() which is part of NXP/i.MX SCMI vendor
extensions.
-----BEGIN PGP SIGNATURE-----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=dloZ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=dTib
-----END PGP SIGNATURE-----
Merge tag 'scmi-fix-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fix for v6.14
Just a single fix to address the incorrect size of the Tx buffer in the
function scmi_imx_misc_ctrl_set() which is part of NXP/i.MX SCMI vendor
extensions.
* tag 'scmi-fix-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: imx: Correct tx size of scmi_imx_misc_ctrl_set
Link: https://lore.kernel.org/r/20250217155246.1668182-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While setting the DAC value, the wrong boolean value is evaluated to set
the DSP bias current. So let's correct the conditional statement and use
the right boolean value read from the DTS set in the priv.
Cc: stable@vger.kernel.org
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250219130923.7216-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netdevsim driver was experiencing NOHZ tick-stop errors during packet
transmission due to pending softirq work when calling napi_schedule().
This issue was observed when running the netconsole selftest, which
triggered the following error message:
NOHZ tick-stop error: local softirq work is pending, handler #08!!!
To fix this issue, introduce a timer that schedules napi_schedule()
from a timer context instead of calling it directly from the TX path.
Create an hrtimer for each queue and kick it from the TX path,
which then schedules napi_schedule() from the timer context.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250219-netdevsim-v3-1-811e2b8abc4c@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the hidden assumption that options are allocated at the end of
the struct, and teach the compiler about them using a flexible array.
With this, we can revert the unsafe_memcpy() call we have in
tun_dst_unclone() [1], and resolve the false field-spanning write
warning caused by the memcpy() in ip_tunnel_info_opts_set().
The layout of struct ip_tunnel_info remains the same with this patch.
Before this patch, there was an implicit padding at the end of the
struct, options would be written at 'info + 1' which is after the
padding.
This will remain the same as this patch explicitly aligns 'options'.
The alignment is needed as the options are later casted to different
structs, and might result in unaligned memory access.
Pahole output before this patch:
struct ip_tunnel_info {
struct ip_tunnel_key key; /* 0 64 */
/* XXX last struct has 1 byte of padding */
/* --- cacheline 1 boundary (64 bytes) --- */
struct ip_tunnel_encap encap; /* 64 8 */
struct dst_cache dst_cache; /* 72 16 */
u8 options_len; /* 88 1 */
u8 mode; /* 89 1 */
/* size: 96, cachelines: 2, members: 5 */
/* padding: 6 */
/* paddings: 1, sum paddings: 1 */
/* last cacheline: 32 bytes */
};
Pahole output after this patch:
struct ip_tunnel_info {
struct ip_tunnel_key key; /* 0 64 */
/* XXX last struct has 1 byte of padding */
/* --- cacheline 1 boundary (64 bytes) --- */
struct ip_tunnel_encap encap; /* 64 8 */
struct dst_cache dst_cache; /* 72 16 */
u8 options_len; /* 88 1 */
u8 mode; /* 89 1 */
/* XXX 6 bytes hole, try to pack */
u8 options[] __attribute__((__aligned__(16))); /* 96 0 */
/* size: 96, cachelines: 2, members: 6 */
/* sum members: 90, holes: 1, sum holes: 6 */
/* paddings: 1, sum paddings: 1 */
/* forced alignments: 1, forced holes: 1, sum forced holes: 6 */
/* last cacheline: 32 bytes */
} __attribute__((__aligned__(16)));
[1] Commit 13cfd6a6d7 ("net: Silence false field-spanning write warning in metadata_dst memcpy")
Link: https://lore.kernel.org/all/53D1D353-B8F6-4ADC-8F29-8C48A7C9C6F1@kernel.org/
Suggested-by: Kees Cook <kees@kernel.org>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250219143256.370277-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tunnel options should not be accessed directly, use the ip_tunnel_info()
accessor instead.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250219143256.370277-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
32-bit s390 is very close to the existing 64-bit implementation.
Some special handling is necessary as there is neither LLVM nor
QEMU support. Also the kernel itself can not build natively for 32-bit
s390, so instead the test program is executed with a 64-bit kernel.
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20250206-nolibc-s390-v2-2-991ad97e3d58@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Support for 32-bit s390 is about to be added.
As "s39032" would look horrible, use the another naming scheme.
32-bit s390 is "s390" and 64-bit s390 is "s390x",
similar to how it is handled in various toolchain components.
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20250206-nolibc-s390-v2-1-991ad97e3d58@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
The nolibc testsuite can be run against other libcs to test for
interoperability. Some aspects of the constructor execution are not
standardized and musl does not provide all tested feature, for one it
does not provide arguments to the constructors, anymore?
Skip the constructor tests on non-nolibc configurations.
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20250212-nolibc-test-constructor-v1-1-c963875b3da4@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
The tests:
trigger-action-hist-xfail.tc
trigger-onchange-action-hist.tc
trigger-snapshot-action-hist.tc
trigger-hist-expressions.tc
can all run in an instance. Test them in an instance as well.
Link: https://lore.kernel.org/r/20250220185846.451234966@goodmis.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The triggers set in trigger-onchange-action-hist.tc and
trigger-snapshot-action-hist.tc are not cleaned up at the end. These tests
can also be done in instances and without cleaning up the triggers, the
instances can not be removed as they are still "busy".
Link: https://lore.kernel.org/r/20250220185846.291817731@goodmis.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
For the tests that have both a README attribute as well as the instance
flag to run the tests as an instance, the instance version will always
exit with UNSUPPORTED. That's because the instance directory does not
contain a README file. Currently, the tests check for a README file in the
directory that the test runs in and if there's a requirement for something
to be present in the README file, it will not find it, as the instance
directory doesn't have it.
Have the tests check if the current directory is an instance directory,
and if it is, check two directories above the current directory for the
README file:
/sys/kernel/tracing/README
/sys/kernel/tracing/instances/foo/../../README
Link: https://lore.kernel.org/r/20250220185846.130216270@goodmis.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The Energy Model framework had some recent grow and became a bit
more complex. Add the proper contact points to maintainers so
other developers can get the right support.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20250220114103.515278-1-lukasz.luba@arm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The callback function of call_rcu() just calls kfree(), so use
kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20250218082021.2766-1-lirongqing@baidu.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Describe TPS546B24 DC-DC converter which is very similar to tps546d24
version. The difference is that B version handles up to 20A. D version up
to 40A.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/c79f69d0d37e7eb61f93f5dea69148b7756a3ee5.1740056021.git.michal.simek@amd.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
We observed an issue that the CPU frequency can't raise up with a 100% CPU
load when NOHZ is off and the 'conservative' governor is selected.
'idle_time' can be negative if it's obtained from get_cpu_idle_time_jiffy()
when NOHZ is off. This was found and explained in commit 9485e4ca0b
("cpufreq: governor: Fix handling of special cases in dbs_update()").
However, commit 7592019634 ("cpufreq: governors: Fix long idle detection
logic in load calculation") introduced a comparison between 'idle_time' and
'samling_rate' to detect a long idle interval. While 'idle_time' is
converted to int before comparison, it's actually promoted to unsigned
again when compared with an unsigned 'sampling_rate'. Hence, this leads to
wrong idle interval detection when it's in fact 100% busy and sets
policy_dbs->idle_periods to a very large value. 'conservative' adjusts the
frequency to minimum because of the large 'idle_periods', such that the
frequency can't raise up. 'Ondemand' doesn't use policy_dbs->idle_periods
so it fortunately avoids the issue.
Correct negative 'idle_time' to 0 before any use of it in dbs_update().
Fixes: 7592019634 ("cpufreq: governors: Fix long idle detection logic in load calculation")
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Link: https://patch.msgid.link/20250213035510.2402076-1-zhanjie9@hisilicon.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cgroups controller is currently maintained through the
drm-misc tree, so lets add Maxime Ripard, Natalie Vock
and me as specific maintainers for dmem.
We keep the cgroup mailing list CC'd on all cgroup specific patches.
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Natalie Vock <natalie.vock@gmx.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Koutný <mkoutny@suse.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250220140757.16823-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
