The Retu IRQ is off by one, as a result the power button does not work.
Fix it.
Fixes: 084b6f2167 ("ARM: omap1: Fix up the Nokia 770 board device IRQs")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Z3UxH_fOzuftjnuX@darkstar.musicnaut.iki.fi
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the newly-added charger of TWL603X in the defconfig since it is
used by the Epson Moverio BT200.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241229144459.9742-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-18-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-17-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-16-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-15-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-14-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-13-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
3. On targets like SDX75, intermittent disconnects were observed
with certain cables due to impedence variations.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-12-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-11-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-10-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-9-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-8-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-7-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-6-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-5-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-4-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-3-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-2-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define inet_sk_dscp() to get a dscp_t value from struct inet_sock, so
that sctp_v4_get_dst() can easily set ->flowi4_tos from a dscp_t
variable. For the SCTP_DSCP_SET_MASK case, we can just use
inet_dsfield_to_dscp() to get a dscp_t value.
Then, when converting ->flowi4_tos from __u8 to dscp_t, we'll just have
to drop the inet_dscp_to_dsfield() conversion function.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/1a645f4a0bc60ad18e7c0916642883ce8a43c013.1735835456.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dr. David Alan Gilbert says:
====================
igc deadcoding
This set removes some functions that are entirely unused
and have been since ~2018.
====================
Link: https://patch.msgid.link/20250102174142.200700-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last uses of igc_read_pcie_cap_reg() and igc_write_pcie_cap_reg()
were removed in 2019 by
commit 16ecd8d9af ("igc: Remove the obsolete workaround")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102174142.200700-4-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_read_pci_cfg() and igc_write_pci_cfg were added in 2018 as part of
commit 146740f9ab ("igc: Add support for PF")
but have remained unused.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102174142.200700-3-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
igc_acquire_nvm() and igc_release_nvm() were added in 2018 as part of
commit ab40561268 ("igc: Add NVM support")
but never used.
Remove them.
The igc_1225.c has it's own specific implementations.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102174142.200700-2-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dr. David Alan Gilbert says:
====================
i40e deadcoding
This is a bunch of deadcoding of functions that
are entirely uncalled in the i40e driver.
Build tested only.
====================
Link: https://patch.msgid.link/20250102173717.200359-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last useof i40e_dcb_hw_get_num_tc() was removed in 2022 by
commit fe20371578 ("Revert "i40e: Fix reset bw limit when DCB enabled
with 1 TC"")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-10-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_asq_send_command_v2() was added in 2022 by
commit 74073848b0 ("i40e: Add new versions of send ASQ command
functions")
but hasn't been used.
Remove it.
(The _atomic_v2 version of the function is used, so leave it).
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-9-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_commit_partition_bw_setting() was added in 2017 by
commit 4fc8c67639 ("i40e: genericize the partition bandwidth control")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-8-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last use of i40e_del_filter() was removed in 2016 by
commit 9569a9a454 ("i40e: when adding or removing MAC filters, correctly
handle VLANs")
Remove it.
Fix up a comment that referenced it.
Note: The __ version of this function is still used.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-7-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The last use of i40e_get_cur_guaranteed_fd_count() was removed in 2015 by
commit 04294e38a4 ("i40e: FD filters flush policy changes")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-6-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_add_pinfo_to_list() was added in 2017 by
commit 1d5c960c5e ("i40e: new AQ commands")
i40e_find_section_in_profile() was added in 2019 by
commit cdc594e003 ("i40e: Implement DDP support in i40e driver")
Neither have been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-5-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_read_phy_register() and i40e_write_phy_register() were added in
2016 by
commit f62ba91458 ("i40e: Add functions which apply correct PHY access
method for read and write operation")
but haven't been used.
Remove them.
(There are more specific _clause* variants of these functions
that are still used.)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-4-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_blink_phy_link_led() was added in 2016 by
commit fd077cd339 ("i40e: Add functions to blink led on 10GBaseT PHY")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-3-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_aq_add_mirrorrule(), i40e_aq_delete_mirrorrule() and
i40e_aq_set_vsi_vlan_promisc() were added in 2016 by
commit 7bd6875bef ("i40e: APIs to Add/remove port mirroring rules")
but haven't been used.
They were the last user of i40e_mirrorrule_op().
i40e_aq_rearrange_nvm() was added in 2018 by
commit f05798b4ff ("i40e: Add AQ command for rearrange NVM structure")
but hasn't been used.
i40e_aq_restore_lldp() was added in 2019 by
commit c65e78f87f ("i40e: Further implementation of LLDP")
but hasn't been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250102173717.200359-2-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the vendor prefix for a manufacturer of EEPROM chips among others.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250103-fp5-cam-eeprom-v1-2-88dee1b36f8e@fairphone.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[Why]
Wrapper functions for dcn_bw_ceil2() and dcn_bw_floor2()
should check for granularity is non zero to avoid assert and
divide-by-zero error in dcn_bw_ functions.
[How]
Add check for granularity 0.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6e09701c3)
Cc: stable@vger.kernel.org
As the hw supports up to 4 surfaces, increase the maximum number of
surfaces to prevent the DC error when trying to use more than three
planes.
[drm:dc_state_add_plane [amdgpu]] *ERROR* Surface: can not attach plane_state 000000003e2cb82c! Maximum is: 3
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3693
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b8d6daffc8)
Cc: stable@vger.kernel.org
[WHY & HOW]
commit 7fb363c575 ("drm/amd/display: Let drm_crtc_vblank_on/off manage interrupts")
lets drm_crtc_vblank_* to manage interrupts in amdgpu_dm_crtc_set_vblank,
and amdgpu_irq_get/put do not need to be called here. Part of that
patch got lost somehow, so fix it up.
Fixes: 7fb363c575 ("drm/amd/display: Let drm_crtc_vblank_on/off manage interrupts")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3782305ce5)
Cc: stable@vger.kernel.org
container_of cannot return NULL, so it is unnecessary to check for
NULL after gem_to_amdgpu_bo, which is just a container_of call
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fill max memory bandwidth and total app clock counter to metrics v1_7
v2: Remove unnecessary check
v3: Add app clock counter support for apu
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update pmfw headers for smuv13.0.6 to pmfw version 85.121
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
