This makes it possible to disable the MSG_OOB support in .config.
Signed-off-by: Florent Revest <revest@chromium.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241218143334.1507465-1-revest@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From: Andy Moreton <andy.moreton@amd.com>
efx_writed_page_locked is a workaround for Siena hardware that is not
needed on later adapters, and has no callers. Remove it.
Signed-off-by: Andy Moreton <andy.moreton@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20241218135930.2350358-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 2af6106ae9 ("net: stmmac: Introducing support for Page
Pool"), the driver always copies frames to get a better performance,
zero-copy for RX frames is no more, then these code turned to be
useless and users of ethtool may get confused about the unhandled
rx-copybreak parameter.
This patch mostly reverts
commit 22ad383815 ("stmmac: do not perform zero-copy for rx frames")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20241218083407.390509-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document expectations from drivers looking to add support for device
memory tcp or other netmem based features.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://patch.msgid.link/20241217201206.2360389-1-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not run napi_disable() if airoha_hw_init() fails since Tx/Rx napi
has not been started yet. In order to fix the issue, introduce
airoha_qdma_stop_napi routine and remove napi_disable in
airoha_hw_cleanup().
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20241216-airoha_probe-error-path-fix-v2-1-6b10e04e9a5c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
net: add and use phy_disable_eee
If a MAC driver doesn't support EEE, then the PHY shouldn't advertise it.
Add phy_disable_eee() for this purpose, and use it in cpsw driver.
====================
Link: https://patch.msgid.link/5139374e-7151-4d0d-8ba9-9ec3d9b52f67@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems the cpsw MAC doesn't support EEE. See e.g. the commit message of
ce2899428e ("ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY").
There are cases where this causes issues if the PHY's on both sides have
negotiated EEE. As a workaround EEE modes of the PHY are marked broken
in DT, effectively disabling EEE advertisement.
Improve this by using new function phy_disable_eee() in the MAC driver.
This properly disables EEE advertisement, and allows to remove the
eee-broken-xxx properties from DT. As EEE is disabled anyway, we can
remove also the set_eee ethtool op.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/d08a798e-8565-422c-b2ed-121794db077f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a MAC driver doesn't support EEE, then the PHY shouldn't advertise it.
Add phy_disable_eee() for this purpose.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/fd51738c-dcd6-4d61-b8c5-faa6ac0f1026@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multi-Link Operation implementation continues, both in stack and in
drivers. Otherwise it has been relatively quiet.
Major changes:
cfg80211/mac80211
* define wiphy guard
* get TX power per link
* EHT 320 MHz channel support for mesh
ath11k
* QCA6698AQ support
ath9k
* RX inactivity detection
rtl8xxxu
* add more USB device IDs
rtw88
* add more USB device IDs
* enable USB RX aggregation and USB 3 to improve performance
rtw89
* PowerSave flow for Multi-Link Operation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmdkbAoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuRIgf/dcjYr+eg3I7iU9qGxvEwHlDAC5CaMRwe
8+/SO6gy49xf6igleNQ2jBn/qAsJTiro6IzJwb1D6i16ax4TRUTEkTZSiYCzntKI
9Nkq59qhsRI4Vxrhp6NibUtVnjuRdSruVM5uLCccUCJ8tfq13WGhecR2pmV0TDO3
bRSza6L64XIuSmqHkuWS3Hz1YQvIvIZMeeiWoC35mtXg6ORRXpYloLtCzFn1zxoP
YPoeSfoAqIlaVwdB1DoaakU6is8oGZ0oI6zw/qaN8P7pYfqO62ATf6ZzAdwHE1dU
fow9nvwzln+BqgpdIK81QFR+XC+7LorCGSaQlYu6C0nxjSzycSrgOw==
=WIP7
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.14
Multi-Link Operation implementation continues, both in stack and in
drivers. Otherwise it has been relatively quiet.
Major changes:
cfg80211/mac80211
- define wiphy guard
- get TX power per link
- EHT 320 MHz channel support for mesh
ath11k
- QCA6698AQ support
ath9k
- RX inactivity detection
rtl8xxxu
- add more USB device IDs
rtw88
- add more USB device IDs
- enable USB RX aggregation and USB 3 to improve performance
rtw89
- PowerSave flow for Multi-Link Operation
* tag 'wireless-next-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (121 commits)
wifi: wlcore: sysfs: constify 'struct bin_attribute'
wifi: brcmfmac: clarify unmodifiable headroom log message
wifi: brcmfmac: add missing header include for brcmf_dbg
wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
wifi: qtnfmac: fix spelling error in core.h
wifi: rtw89: phy: add dummy C2H event handler for report of TAS power
wifi: rtw89: 8851b: rfk: remove unnecessary assignment of return value of _dpk_dgain_read()
wifi: rtw89: 8852c: rfk: refine target channel calculation in _rx_dck_channel_calc()
wifi: rtlwifi: pci: wait for firmware loading before releasing memory
wifi: rtlwifi: fix memory leaks and invalid access at probe error path
wifi: rtlwifi: destroy workqueue at rtl_deinit_core
wifi: rtlwifi: remove unused check_buddy_priv
wifi: rtw89: 8922a: update format of RFK pre-notify H2C command v2
wifi: rtw89: regd: update regulatory map to R68-R51
wifi: rtw89: 8852c: disable ER SU when 4x HE-LTF and 0.8 GI capability differ
wifi: rtw89: disable firmware training HE GI and LTF
wifi: rtw89: ps: update data for firmware and settings for hardware before/after PS
wifi: rtw89: ps: refactor channel info to firmware before entering PS
wifi: rtw89: ps: refactor PS flow to support MLO
wifi: mwifiex: decrease timeout waiting for host sleep from 10s to 5s
...
====================
Link: https://patch.msgid.link/20241219185709.774EDC4CECE@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Few minor fixes this time, nothing special.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmdkai8RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtMzggAlOw9WMwAogFL3hE/IkfNkkiJPsDLd1Z8
vnGOJVHKQhGjGDY1hPv/ezV9t0wVrzRPYK84prcFU52g1WUi1d9bxAM2VRw0HNt9
y3ARGryc7rwiGMzafxUkDj6uJu5QkW4tHvLq8Uo+1PyU3iAheOQielOcSkr4PAu1
E6KyhPLQ9zehJ4REr/9E0M7ddCM87F6Tcm2FS1ulcG9YvbsP7cqE5j04ZUA+fIZk
0+EVwfxjzyXymaVY8cS6mxzU/vusAOS6oWZmLl6YqydPiePI1PlW54bmx8J4l5yW
ZfkuqAn0aROUqrstzJEyPMr3C0a5FVNabbmjdV9yD3KolbCQpIapYQ==
=te4y
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.13-rc5
Few minor fixes this time, nothing special.
* tag 'wireless-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cw1200: Fix potential NULL dereference
wifi: iwlwifi: mvm: Fix __counted_by usage in cfg80211_wowlan_nd_*
MAINTAINERS: wifi: ath: add Jeff Johnson as maintainer
wifi: iwlwifi: fix CRF name for Bz
====================
Link: https://patch.msgid.link/20241219185042.662B6C4CECE@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot can figure out a way to redirect a netlink message to a tap.
Sending empty skbs to devices is not valid and we end up hitting
a skb_assert_len() in __dev_queue_xmit().
Make catching these mistakes easier, assert the skb size directly
in netlink core.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241218024400.824355-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ DSA driver starts a timer to read MIB counters periodically to
avoid count overrun. During system suspend this will give an error for
not able to write to register as the SPI system returns an error when
it is in suspend state. This implementation stops the timer when the
system goes into suspend and restarts it when resumed.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020311.70628-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tristram Ha says:
====================
net: dsa: microchip: Fix set_ageing_time function for KSZ9477 and LAN937X switches
The aging count is not a simple number that is broken into two parts and
programmed into 2 registers. These patches correct the programming for
KSZ9477 and LAN937X switches.
====================
Link: https://patch.msgid.link/20241218020224.70590-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 20-bit value but comprises a 3-bit
multiplier and a 20-bit second time. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
As the 20-bit number is now too large for practical use there is an option
to interpret it as microseconds instead of seconds.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 11-bit value but comprises a 3-bit
multiplier and an 8-bit second count. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-2-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The host_node pointer was assigned and freed in adv7533_parse_dt(), and
later, adv7533_attach_dsi() uses the same. Fix this use-after-free issue
by dropping of_node_put() in adv7533_parse_dt() and calling of_node_put()
in error path of probe() and also in the remove().
Fixes: 1e4d58cd7f ("drm/bridge: adv7533: Create a MIPI DSI device")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119192040.152657-2-biju.das.jz@bp.renesas.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Treat slow-path TDP MMU faults as spurious if the access is allowed given
the existing SPTE to fix a benign warning (other than the WARN itself)
due to replacing a writable SPTE with a read-only SPTE, and to avoid the
unnecessary LOCK CMPXCHG and subsequent TLB flush.
If a read fault races with a write fault, fast GUP fails for any reason
when trying to "promote" the read fault to a writable mapping, and KVM
resolves the write fault first, then KVM will end up trying to install a
read-only SPTE (for a !map_writable fault) overtop a writable SPTE.
Note, it's not entirely clear why fast GUP fails, or if that's even how
KVM ends up with a !map_writable fault with a writable SPTE. If something
else is going awry, e.g. due to a bug in mmu_notifiers, then treating read
faults as spurious in this scenario could effectively mask the underlying
problem.
However, retrying the faulting access instead of overwriting an existing
SPTE is functionally correct and desirable irrespective of the WARN, and
fast GUP _can_ legitimately fail with a writable VMA, e.g. if the Accessed
bit in primary MMU's PTE is toggled and causes a PTE value mismatch. The
WARN was also recently added, specifically to track down scenarios where
KVM is unnecessarily overwrites SPTEs, i.e. treating the fault as spurious
doesn't regress KVM's bug-finding capabilities in any way. In short,
letting the WARN linger because there's a tiny chance it's due to a bug
elsewhere would be excessively paranoid.
Fixes: 1a175082b1 ("KVM: x86/mmu: WARN and flush if resolving a TDP MMU fault clears MMU-writable")
Reported-by: Lei Yang <leiyang@redhat.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219588
Tested-by: Lei Yang <leiyang@redhat.com>
Link: https://lore.kernel.org/r/20241218213611.3181643-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Drop KVM's arbitrary behavior of making DE_CFG.LFENCE_SERIALIZE read-only
for the guest, as rejecting writes can lead to guest crashes, e.g. Windows
in particular doesn't gracefully handle unexpected #GPs on the WRMSR, and
nothing in the AMD manuals suggests that LFENCE_SERIALIZE is read-only _if
it exists_.
KVM only allows LFENCE_SERIALIZE to be set, by the guest or host, if the
underlying CPU has X86_FEATURE_LFENCE_RDTSC, i.e. if LFENCE is guaranteed
to be serializing. So if the guest sets LFENCE_SERIALIZE, KVM will provide
the desired/correct behavior without any additional action (the guest's
value is never stuffed into hardware). And having LFENCE be serializing
even when it's not _required_ to be is a-ok from a functional perspective.
Fixes: 74a0e79df6 ("KVM: SVM: Disallow guest from changing userspace's MSR_AMD64_DE_CFG value")
Fixes: d1d93fa90f ("KVM: SVM: Add MSR-based feature support for serializing LFENCE")
Reported-by: Simon Pilkington <simonp.git@mailbox.org>
Closes: https://lore.kernel.org/all/52914da7-a97b-45ad-86a0-affdf8266c61@mailbox.org
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20241211172952.1477605-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Use is_64_bit_hypercall() instead of is_64_bit_mode() to detect a 64-bit
hypercall when completing said hypercall. For guests with protected state,
e.g. SEV-ES and SEV-SNP, KVM must assume the hypercall was made in 64-bit
mode as the vCPU state needed to detect 64-bit mode is unavailable.
Hacking the sev_smoke_test selftest to generate a KVM_HC_MAP_GPA_RANGE
hypercall via VMGEXIT trips the WARN:
------------[ cut here ]------------
WARNING: CPU: 273 PID: 326626 at arch/x86/kvm/x86.h:180 complete_hypercall_exit+0x44/0xe0 [kvm]
Modules linked in: kvm_amd kvm ... [last unloaded: kvm]
CPU: 273 UID: 0 PID: 326626 Comm: sev_smoke_test Not tainted 6.12.0-smp--392e932fa0f3-feat #470
Hardware name: Google Astoria/astoria, BIOS 0.20240617.0-0 06/17/2024
RIP: 0010:complete_hypercall_exit+0x44/0xe0 [kvm]
Call Trace:
<TASK>
kvm_arch_vcpu_ioctl_run+0x2400/0x2720 [kvm]
kvm_vcpu_ioctl+0x54f/0x630 [kvm]
__se_sys_ioctl+0x6b/0xc0
do_syscall_64+0x83/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: b5aead0064 ("KVM: x86: Assume a 64-bit hypercall for guests with protected state")
Cc: stable@vger.kernel.org
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Nikunj A Dadhania <nikunj@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Link: https://lore.kernel.org/r/20241128004344.4072099-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
On SNP-enabled system, VMRUN marks AVIC Backing Page as in-use while
the guest is running for both secure and non-secure guest. Any hypervisor
write to the in-use vCPU's AVIC backing page (e.g. to inject an interrupt)
will generate unexpected #PF in the host.
Currently, attempt to run AVIC guest would result in the following error:
BUG: unable to handle page fault for address: ff3a442e549cc270
#PF: supervisor write access in kernel mode
#PF: error_code(0x80000003) - RMP violation
PGD b6ee01067 P4D b6ee02067 PUD 10096d063 PMD 11c540063 PTE 80000001149cc163
SEV-SNP: PFN 0x1149cc unassigned, dumping non-zero entries in 2M PFN region: [0x114800 - 0x114a00]
...
Newer AMD system is enhanced to allow hypervisor to modify the backing page
for non-secure guest on SNP-enabled system. This enhancement is available
when the CPUID Fn8000_001F_EAX bit 30 is set (HvInUseWrAllowed).
This table describes AVIC support matrix w.r.t. SNP enablement:
| Non-SNP system | SNP system
-----------------------------------------------------
Non-SNP guest | AVIC Activate | AVIC Activate iff
| | HvInuseWrAllowed=1
-----------------------------------------------------
SNP guest | N/A | Secure AVIC
Therefore, check and disable AVIC in kvm_amd driver when the feature is not
available on SNP-enabled system.
See the AMD64 Architecture Programmer’s Manual (APM) Volume 2 for detail.
(https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/
programmer-references/40332.pdf)
Fixes: 216d106c7f ("x86/sev: Add SEV-SNP host initialization support")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20241104075845.7583-1-suravee.suthikulpanit@amd.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Newer firmware does not allow reading the PXP registers during
ethtool -d, so skip the firmware call in that case. Userspace
(bnxt.c) always expects the register block to be populated so
zeroes will be returned instead.
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241217182620.2454075-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the new HWRM_PORT_MAC_QCAPS to check if mac loopback is
supported. Skip the MAC loopback ethtool self test if it is
not supported.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241217182620.2454075-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Skip PHY loopback selftest if firmware advertises that it is unsupported
in the HWRM_PORT_PHY_QCAPS call. Only show PHY loopback test result to
be 0 if the test has run and passes. Do the same for external loopback
to be consistent.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241217182620.2454075-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Block all ethtool module operations on an untrusted VF. The firmware
won't allow it and will return error.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241217182620.2454075-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If FW supports setting resource limits for RoCE, then just use the
FW limits instead of using some fixed values in the driver. These
limits will be used to allocate context memory for QP, SRQ, AH, and
MR resources for RoCE.
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241217182620.2454075-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the i.MX6ULL-14x14-EVK board, enet1_ref and enet2_ref are used as the
clock sources for two external KSZ PHYs. However, after closing the two
FEC ports, the clk_enable_count of the enet1_ref and enet2_ref clocks is
not 0. The root cause is that since the commit 9853294627 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
external clock of KSZ PHY has been enabled when the PHY driver probes,
and it can only be disabled when the PHY driver is removed. This causes
the clock to continue working when the system is suspended or the network
port is down.
Although Heiko explained in the commit message that the patch was because
some clock suppliers need to enable the clock to get the valid clock rate
, it seems that the simple fix is to disable the clock after getting the
clock rate to solve the current problem. This is indeed true, but we need
to admit that Heiko's patch has been applied for more than a year, and we
cannot guarantee whether there are platforms that only enable rmii-ref in
the KSZ PHY driver during this period. If this is the case, disabling
rmii-ref will cause RMII on these platforms to not work.
Secondly, commit 99ac4cbcc2 ("net: phy: micrel: allow usage of generic
ethernet-phy clock") just simply enables the generic clock permanently,
which seems like the generic clock may only be enabled in the PHY driver.
If we simply disable the generic clock, RMII may not work. If we keep it
as it is, the platform using the generic clock will have the same problem
as the i.MX6ULL platform.
To solve this problem, the clock is enabled when phy_driver::resume() is
called, and the clock is disabled when phy_driver::suspend() is called.
Since phy_driver::resume() and phy_driver::suspend() are not called in
pairs, an additional clk_enable flag is added. When phy_driver::suspend()
is called, the clock is disabled only if clk_enable is true. Conversely,
when phy_driver::resume() is called, the clock is enabled if clk_enable
is false.
The changes that introduced the problem were only a few lines, while the
current fix is about a hundred lines, which seems out of proportion, but
it is necessary because kszphy_probe() is used by multiple KSZ PHYs and
we need to fix all of them.
Fixes: 9853294627 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock")
Fixes: 99ac4cbcc2 ("net: phy: micrel: allow usage of generic ethernet-phy clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241217063500.1424011-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The power-supply core already takes care of handling
POWER_SUPPLY_PROP_TECHNOLOGY based on the battery_info.
Drop the unnecessary handling from the driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241215172133.178460-4-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
With DT properties charge-current-limit-gpios and
charge-current-limit-mapping one can define charge current limits in uA
using up to 32 GPIOs. At the moment the driver defaults to smallest charge
current limitation for safety reasons. When disabling charging is
supported, which should be common, the driver defaults to non charging on
probe. By having a default, charging can be enabled on probe for such
devices.
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://lore.kernel.org/r/20241218-default-charge-current-limit-v3-2-b26118cf06b5@liebherr.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
With DT properties charge-current-limit-gpios and
charge-current-limit-mapping one can define charge current limits in uA
using up to 32 GPIOs. Add property charge-current-limit-default-microamp
which selects a default charge current limit that must be listed in
charge-current-limit-mapping.
This is helpful when the smallest possible charge current limit is 0uA. The
driver defaults to the smallest possible value at the moment, which
disables charging on probe. With the default its possible to setup a safe
charge current limit.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://lore.kernel.org/r/20241218-default-charge-current-limit-v3-1-b26118cf06b5@liebherr.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The power-supply core is designed so that power-supply driver callbacks
such as get_property() and external_power_changed() will not be called
until the power-supply's parent driver's probe() function has completed.
There is a race where power_supply_changed() can be called for a supplier
of a power-supply which is being probed after the device_add() in
__power_supply_register() but before the parent driver's probe() function
has completed. Hitting this race breaks the power-supply core's design
to not call power-supply driver callbacks before probe() completion.
This problem is caused by __power_supply_changed_work() calling
the external_power_changed() directly rather then going through
the power_supply_external_power_changed() helper which correcly checks
psy->use_cnt .
Switch to using power_supply_external_power_changed() to fix this race.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241215172133.178460-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a typo in function call and instead of VF LMEM we were
looking at VF GGTT provisioning. Fix that.
Fixes: 234670cea9 ("drm/xe/pf: Skip fair VFs provisioning if already provisioned")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216223253.819-1-michal.wajdeczko@intel.com
Commit 2563391e57 ("drm/amd/display: DML2.1 resynchronization") blew
away the compiler warning fix from commit 2fde4fdddc
("drm/amd/display: Avoid -Wenum-float-conversion in
add_margin_and_round_to_dfs_grainularity()"), causing the warning to
reappear.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml21/src/dml2_dpmm/dml2_dpmm_dcn4.c:183:58: error: arithmetic between enumeration type 'enum dentist_divider_range' and floating-point type 'double' [-Werror,-Wenum-float-conversion]
183 | divider = (unsigned int)(DFS_DIVIDER_RANGE_SCALE_FACTOR * (vco_freq_khz / clock_khz));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
Apply the fix again to resolve the warning.
Re-apply again after commit be4e350931 ("drm/amd/display: DML21 Reintegration For Various Fixes")
This should be making its way back to the original DML trees this time. (Alex)
Fixes: be4e350931 ("drm/amd/display: DML21 Reintegration For Various Fixes")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3841
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the hw supports up to 4 surfaces, increase the maximum number of
surfaces to prevent the DC error when trying to use more than three
planes.
[drm:dc_state_add_plane [amdgpu]] *ERROR* Surface: can not attach plane_state 000000003e2cb82c! Maximum is: 3
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3693
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
commit 7fb363c575 ("drm/amd/display: Let drm_crtc_vblank_on/off manage interrupts")
lets drm_crtc_vblank_* to manage interrupts in amdgpu_dm_crtc_set_vblank,
and amdgpu_irq_get/put do not need to be called here. Part of that
patch got lost somehow, so fix it up.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we've exposed Lock::from_raw() and Guard::new() publically, we
want to be able to make sure that we assert that a lock is actually held
when constructing a Guard for it to handle instances of unsafe
Guard::new() calls outside of our lock module.
Hence add a new method assert_is_held() to Backend, which uses lockdep
to check whether or not a lock has been acquired. When lockdep is
disabled, this has no overhead.
[Boqun: Resolve the conflicts with exposing Guard::new(), reword the
commit log a bit and format "unsafe { <statement>; }" into "unsafe {
<statement> }" for the consistency. ]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20241125204139.656801-1-lyude@redhat.com
A simple helper alias for code that needs to deal with Guard types returned
from SpinLocks.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20241120222742.2490495-3-lyude@redhat.com
A simple helper alias for code that needs to deal with Guard types returned
from Mutexes.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20241120222742.2490495-2-lyude@redhat.com
Since we added a `Lock::from_raw()` function previously, it makes sense
to also introduce an interface for creating a `Guard` from a reference
to a `Lock` for instances where we've derived the `Lock` from a raw
pointer and know that the lock is already acquired, there are such
usages in KMS API.
[Boqun: Add backquotes to type names, reformat the commit log, reword a
bit on the usage of KMS API]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Filipe Xavier <felipe_life@live.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20241119231146.2298971-3-lyude@redhat.com
The KMS bindings [1] have a few bindings that require manually acquiring
specific locks before calling certain functions. At the moment though,
the only way of acquiring these locks in bindings is to simply call the
C locking functions directly - since said locks are not initialized on
the Rust side of things.
However - if we add `#[repr(C)]` to `Lock<(), B>`, then given `()` is a
ZST - `Lock<(), B>` becomes equivalent in data layout to its inner
`B::State` type. Since locks in C don't have data explicitly associated
with them anyway, we can take advantage of this to add a
`Lock::from_raw()` function that can translate a raw pointer to
`B::State` into its proper `Lock<(), B>` equivalent. This lets us simply
acquire a reference to the lock in question and work with it like it was
initialized on the Rust side of things, allowing us to use less unsafe
code to implement bindings with lock requirements.
[Boqun: Use "Link:" instead of a URL and format the commit log]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patchwork.freedesktop.org/series/131522/ [1]
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20241119231146.2298971-2-lyude@redhat.com
It makes sense to add Rust locking primitives under the watch of general
locking primitives maintainers. This will encourage more reviews and
find potential issues earlier. Hence add related Rust files into the
LOCKING PRIMITIVES entry in MAINTAINERS.
While we are at it, change the role of myself into the maintainer of
LOCKDEP and RUST to reflect my responsibility for the corresponding
code.
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
https://lore.kernel.org/lkml/20241128054022.19586-2-boqun.feng@gmail.com/
