After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/perf to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241027180313.410964-2-u.kleine-koenig@baylibre.com
Signed-off-by: Will Deacon <will@kernel.org>
This SPI controller is present in Apple SoCs such as the M1 (t8103) and
M1 Pro/Max (t600x). It is a relatively straightforward design with two
16-entry FIFOs, arbitrary transfer sizes (up to 2**32 - 1) and fully
configurable word size up to 32 bits. It supports one hardware CS line
which can also be driven via the pinctrl/GPIO driver instead, if
desired. TX and RX can be independently enabled.
There are a surprising number of knobs for tweaking details of the
transfer, most of which we do not use right now. Hardware CS control
is available, but we haven't found a way to make it stay low across
multiple logical transfers, so we just use software CS control for now.
There is also a shared DMA offload coprocessor that can be used to handle
larger transfers without requiring an IRQ every 8-16 words, but that
feature depends on a bunch of scaffolding that isn't ready to be
upstreamed yet, so leave it for later.
The hardware shares some register bit definitions with spi-s3c24xx which
suggests it has a shared legacy with Samsung SoCs, but it is too
different to warrant sharing a driver.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Janne Grunau <j@jannau.net>
Link: https://patch.msgid.link/20241106-asahi-spi-v5-2-e81a4f3a8e19@jannau.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The Apple SPI controller is present in SoCs such as the M1 (t8103) and
M1 Pro/Max (t600x). This controller uses one IRQ and one clock, and
doesn't need any special properties, so the binding is trivial.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Link: https://patch.msgid.link/20241106-asahi-spi-v5-1-e81a4f3a8e19@jannau.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the schema binding for the Iron Device SMA1307 Amp
Signed-off-by: Kiseok Jo <kiseok.jo@irondevice.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241106005800.7520-2-kiseok.jo@irondevice.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_SDCA can't be optional when SND_SOC_ACPI_INTEL_SDCA_QUIRKS is
selected. IS_REACHABLE can prevent the link error. However it is not
suitable for this case. When CONFIG_SND_SOC_ACPI_INTEL_SDCA_QUIRKS is
Y and CONFIG_SND_SOC_SDCA is M, the SDCA helpers will be empty and
return false. But we need the helpers to do their jobs whenSND_SOC_SDCA
is M.
IOW, the SDCA library is not optional for Intel platforms where the
SDCA_QUIRK is selected.
Also, make SND_SOC_SDCA invisible. SND_SOC_SDCA should be selected if
a device supports SDCA. User should not unselect it.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411021722.DiX1Y5sf-lkp@intel.com/
Suggested-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241106055810.10123-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_ACPI_INTEL_MATCH relies on ACPI functions. It will not work
if ACPI is not selected.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241106055810.10123-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The capacity level mappings are taken from:
https://support.steelseries.com/hc/en-us/articles/360049205612-How-do-I-know-the-Arctis-battery-level-how-do-I-charge-the-Arctis
Even if we have a percentage, exporting a capacity_level that matches
with the hardware warning levels means that upower can show warnings at
the same time as the hardware. So the headset starts beeping at the same
time as the critical warning notification appears :eyeroll:
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In some cases, the headset receiver will answer one of our requests with
garbage, or not at all. This is a problem when we only request battery
information once we've received a battery response, as we might never
get to request battery information again.
If the data from the receiver could not be parsed, and there's no
pending battery requests, schedule a new request.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When compiling an MMU kernel without any platform support, e.g.
"MMU=y allnoconfig":
echo CONFIG_MMU=y > allno.config
make KCONFIG_ALLCONFIG=1 allnoconfig
NR_IRQS is zero, causing a build failure:
kernel/irq/irqdesc.c:593:3: error: array index in initializer exceeds array bounds
593 | [0 ... NR_IRQS-1] = {
| ^
kernel/irq/irqdesc.c:593:3: note: (near initialization for ‘irq_desc’)
kernel/irq/irqdesc.c:593:22: warning: excess elements in array initializer
593 | [0 ... NR_IRQS-1] = {
| ^
kernel/irq/irqdesc.c:593:22: note: (near initialization for ‘irq_desc’)
Fix this by setting the default value of NR_IRQS to 8, which is the
mininum number of interrupts on any m68k CPU (the DIP48 variant of the
MC68008 has tied IPL0 and IPL2 together, but that does not impact the
range).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/71db70dc27b46e5326518cd23cb94fa6bee172fe.1730805216.git.geert@linux-m68k.org
Building without a CPU selected does not work.
Change the Kconfig logic slightly to make sure we always pick M68020 if
nothing else is enabled. There are still some intentional warnings for
builds with all platforms disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20241030195638.22542-2-arnd@kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It is possible to select an m68k MMU build but not actually enable any
of the three MMU options, which then results in a build failure:
arch/m68k/include/asm/page.h:10:25: error: 'CONFIG_PAGE_SHIFT' undeclared here (not in a function); did you mean 'CONFIG_LOG_BUF_SHIFT'?
Change the Kconfig selection to ensure that exactly one of the three
options is always enabled whenever an MMU-enabled kernel is built, but
moving CONFIG_SUN3 into a top-level option next to M68KCLASSIC and
COLDFIRE.
All defconfig files should keep working without changes, but
alldefconfig now builds support for the classic MMU.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408032138.P7sBvIns-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20241030195638.22542-1-arnd@kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove hard-coded strings by using the str_read_write() helper function
and remove some unnecessary negations.
Compile-tested only.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20241020205758.332095-1-thorsten.blum@linux.dev
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
When using static keys early, e.g. by specifying "thread_backlog_napi"
on the kernel command line:
WARNING: CPU: 0 PID: 0 at include/linux/jump_label.h:322 setup_backlog_napi_threads+0x40/0xa0
static_key_enable(): static key '0x5ceec0' used before call to jump_label_init()
The function jump_label_init() should be called from setup_arch() very
early for proper functioning of jump label support.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20241016-fix-jump-label-v1-1-eb74c5f68405@yoseli.org
[geert: Add reproducer]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Sometime long ago the m68k IRQ code was refactored and the interrupt
numbers for SCSI controller on this board ended up wrong, and it hasn't
worked since.
The PCC adds 0x40 to the vector for its interrupts so they end up in
the user interrupt range. Hence, the kernel number should be the kernel
offset for user interrupt range + the PCC interrupt number.
Fixes: 200a3d352c ("[PATCH] m68k: convert VME irq code")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/0e7636a21a0274eea35bfd5d874459d5078e97cc.1727926187.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mvme147_sched_init() is only used once at init time
so it can be made __init and save a few bytes of memory.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/20240929025506.1212237-1-daniel@0x0f.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Implement the hid get/set feature report function using a separate
address, rather than sharing an address with coordinate reporting, to
prevent feature events from being overwritten by coordinate events.
Signed-off-by: Charles Wang <charles.goodix@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Align with the i2c-hid driver by returning 0 instead of -EINVAL when
an empty response is received, ensuring that userspace programs utilizing
the hidraw node receive consistent return values.
Signed-off-by: Charles Wang <charles.goodix@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
To properly support VF Save/Restore procedure, fixups need to be
applied after PF driver finishes its part of VF Restore. The fixups
are required to adjust the ongoing execution for a hardware switch
that happened, because some GFX resources are not fully virtualized,
and assigned to a VF as range from a global pool. The VF on which
a VM is restored will often have different ranges provisioned than
the VF on which save process happened. Those resource fixups are
applied by the VF driver within a restored VM.
A VF driver gets informed that it was migrated by receiving an
interrupt from each GuC. The interrupt assigned for that purpose
is "GUC SW interrupt 0". Seeing that fields set from within the
irq handler should be the trigger for fixups.
The VF can safely do post-migration fixups on resources associated
to each GuC only after that GuC issued the MIGRATED interrupt.
This change introduces a worker to be used for post-migration fixups,
and a mechanism to schedule said worker when all GuCs sent the irq.
v2: renamed and moved functions, updated logged messages, removed
unused includes, used anon struct (Michal)
v3: ordering, kerneldoc, asserts, debug messages,
on_all_tiles -> on_all_gts (Michal)
v4: fixed missing header include
v5: Explained what fixups are, explained which IRQ is used, style
fixes (Michal)
Bspec: 50868
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104213449.1455694-2-tomasz.lis@intel.com
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
The logic for handling SVE traps manipulates saved FPSIMD/SVE state
incorrectly, and a race with preemption can result in a task having
TIF_SVE set and TIF_FOREIGN_FPSTATE clear even though the live CPU state
is stale (e.g. with SVE traps enabled). This has been observed to result
in warnings from do_sve_acc() where SVE traps are not expected while
TIF_SVE is set:
| if (test_and_set_thread_flag(TIF_SVE))
| WARN_ON(1); /* SVE access shouldn't have trapped */
Warnings of this form have been reported intermittently, e.g.
https://lore.kernel.org/linux-arm-kernel/CA+G9fYtEGe_DhY2Ms7+L7NKsLYUomGsgqpdBj+QwDLeSg=JhGg@mail.gmail.com/https://lore.kernel.org/linux-arm-kernel/000000000000511e9a060ce5a45c@google.com/
The race can occur when the SVE trap handler is preempted before and
after manipulating the saved FPSIMD/SVE state, starting and ending on
the same CPU, e.g.
| void do_sve_acc(unsigned long esr, struct pt_regs *regs)
| {
| // Trap on CPU 0 with TIF_SVE clear, SVE traps enabled
| // task->fpsimd_cpu is 0.
| // per_cpu_ptr(&fpsimd_last_state, 0) is task.
|
| ...
|
| // Preempted; migrated from CPU 0 to CPU 1.
| // TIF_FOREIGN_FPSTATE is set.
|
| get_cpu_fpsimd_context();
|
| if (test_and_set_thread_flag(TIF_SVE))
| WARN_ON(1); /* SVE access shouldn't have trapped */
|
| sve_init_regs() {
| if (!test_thread_flag(TIF_FOREIGN_FPSTATE)) {
| ...
| } else {
| fpsimd_to_sve(current);
| current->thread.fp_type = FP_STATE_SVE;
| }
| }
|
| put_cpu_fpsimd_context();
|
| // Preempted; migrated from CPU 1 to CPU 0.
| // task->fpsimd_cpu is still 0
| // If per_cpu_ptr(&fpsimd_last_state, 0) is still task then:
| // - Stale HW state is reused (with SVE traps enabled)
| // - TIF_FOREIGN_FPSTATE is cleared
| // - A return to userspace skips HW state restore
| }
Fix the case where the state is not live and TIF_FOREIGN_FPSTATE is set
by calling fpsimd_flush_task_state() to detach from the saved CPU
state. This ensures that a subsequent context switch will not reuse the
stale CPU state, and will instead set TIF_FOREIGN_FPSTATE, forcing the
new state to be reloaded from memory prior to a return to userspace.
Fixes: cccb78ce89 ("arm64/sve: Rework SVE access trap to convert state in registers")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20241030-arm64-fpsimd-foreign-flush-v1-1-bd7bd66905a2@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
In the presence of both weak and strong function definitions, the
linker drops the weak symbol in favor of a strong symbol, but
leaves the code in place. Code in ignore_unreachable_insn() has
some heuristics to suppress the warning, but it does not work when
-ffunction-sections is enabled.
Suppose function foo has both strong and weak definitions.
Case 1: The strong definition has an annotated section name,
like .init.text. Only the weak definition will be placed into
.text.foo. But since the section has no symbols, there will be no
"hole" in the section.
Case 2: Both sections are without an annotated section name.
Both will be placed into .text.foo section, but there will be only one
symbol (the strong one). If the weak code is before the strong code,
there is no "hole" as it fails to find the right-most symbol before
the offset.
The fix is to use the first node to compute the hole if hole.sym
is empty. If there is no symbol in the section, the first node
will be NULL, in which case, -1 is returned to skip the whole
section.
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Suggested-by: Krzysztof Pszeniczny <kpszeniczny@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add the build support for using Clang's AutoFDO. Building the kernel
with AutoFDO does not reduce the optimization level from the
compiler. AutoFDO uses hardware sampling to gather information about
the frequency of execution of different code paths within a binary.
This information is then used to guide the compiler's optimization
decisions, resulting in a more efficient binary. Experiments
showed that the kernel can improve up to 10% in latency.
The support requires a Clang compiler after LLVM 17. This submission
is limited to x86 platforms that support PMU features like LBR on
Intel machines and AMD Zen3 BRS. Support for SPE on ARM 1,
and BRBE on ARM 1 is part of planned future work.
Here is an example workflow for AutoFDO kernel:
1) Build the kernel on the host machine with LLVM enabled, for example,
$ make menuconfig LLVM=1
Turn on AutoFDO build config:
CONFIG_AUTOFDO_CLANG=y
With a configuration that has LLVM enabled, use the following
command:
scripts/config -e AUTOFDO_CLANG
After getting the config, build with
$ make LLVM=1
2) Install the kernel on the test machine.
3) Run the load tests. The '-c' option in perf specifies the sample
event period. We suggest using a suitable prime number,
like 500009, for this purpose.
For Intel platforms:
$ perf record -e BR_INST_RETIRED.NEAR_TAKEN:k -a -N -b -c <count> \
-o <perf_file> -- <loadtest>
For AMD platforms:
The supported system are: Zen3 with BRS, or Zen4 with amd_lbr_v2
For Zen3:
$ cat proc/cpuinfo | grep " brs"
For Zen4:
$ cat proc/cpuinfo | grep amd_lbr_v2
$ perf record --pfm-events RETIRED_TAKEN_BRANCH_INSTRUCTIONS:k -a \
-N -b -c <count> -o <perf_file> -- <loadtest>
4) (Optional) Download the raw perf file to the host machine.
5) To generate an AutoFDO profile, two offline tools are available:
create_llvm_prof and llvm_profgen. The create_llvm_prof tool is part
of the AutoFDO project and can be found on GitHub
(https://github.com/google/autofdo), version v0.30.1 or later. The
llvm_profgen tool is included in the LLVM compiler itself. It's
important to note that the version of llvm_profgen doesn't need to
match the version of Clang. It needs to be the LLVM 19 release or
later, or from the LLVM trunk.
$ llvm-profgen --kernel --binary=<vmlinux> --perfdata=<perf_file> \
-o <profile_file>
or
$ create_llvm_prof --binary=<vmlinux> --profile=<perf_file> \
--format=extbinary --out=<profile_file>
Note that multiple AutoFDO profile files can be merged into one via:
$ llvm-profdata merge -o <profile_file> <profile_1> ... <profile_n>
6) Rebuild the kernel using the AutoFDO profile file with the same config
as step 1, (Note CONFIG_AUTOFDO_CLANG needs to be enabled):
$ make LLVM=1 CLANG_AUTOFDO_PROFILE=<profile_file>
Co-developed-by: Han Shen <shenhan@google.com>
Signed-off-by: Han Shen <shenhan@google.com>
Signed-off-by: Rong Xu <xur@google.com>
Suggested-by: Sriraman Tallam <tmsriram@google.com>
Suggested-by: Krzysztof Pszeniczny <kpszeniczny@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Stephane Eranian <eranian@google.com>
Tested-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Yabin Cui <yabinc@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Tested-by: Peter Jung <ptr1337@cachyos.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241104190628.274717-1-robh@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add a driver to support the Polarfire SoC gpio controller. Interrupt
controller support is unavailable for now and will be added at a later
date.
Signed-off-by: Lewis Hanly <lewis.hanly@microchip.com>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241104-tiny-evaluate-9336020b4b6a@spud
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need to prune the rust/alloc directory because it was
removed by commit 9d0441bab7 ("rust: alloc: remove our fork of the
`alloc` crate").
There is no need to prune the rust/test directory because no '*.rs'
files are generated within it.
To avoid forking the 'grep -Fv generated' process, filter out generated
files using the option, ! -name '*generated*'.
Now that the '-path ... -prune' option is no longer used, there is no
need to use the absolute path. Searching in $(srctree), which can be
a relative path, is sufficient.
The comment mentions the use case where $(srctree) is '..', that is,
$(objtree) is a sub-directory of $(srctree). In this scenario, all
'*.rs' files under $(objtree) are generated files and filters out by
the '*generated*' pattern.
Add $(RCS_FIND_IGNORE) as a shortcut. Although I do not believe '*.rs'
files would exist under the .git directory, there is no need for the
'find' command to traverse it.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Add support for the Vexia EDU ATLA 10 tablet, Android 4.2/4.4 + Guadalinex
Ubuntu tablet distributed to schools in the Spanish Andalucía region.
Besides the usual broken DSDT issues this tablet is special because all
its LPSS island peripherals are enumerated as PCI devices rather then as
ACPI devices as they typically are.
At the same time there are disabled (_STA=0) ACPI devices for
the peripherals and child ACPI devices for e.g. attached I2C/SDIO devices
are children of these disabled ACPI devices and thus will not be used
by Linux since the parent is disabled.
So besides the usual manual i2c-client instantiation for accel/touchscreen
this tablet also requires manual i2c-client instantiation for the codec
and for the PMIC.
Also it seems the mainboard was designed for Windows not Android, so
it has an I2C attached embedded controller instead of allowing direct
access to the charger + fuel-gauge chips as is usual with Android boards.
Normally when there is an embedded controller, there also is ACPI battery
support, but since this shipped with Android that is missing and Linux
needs to have a power_supply class driver talking directly to the EC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241104200848.58693-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
On the Vexia EDU ATLA 10 tablet, which ships with Android + a custom Linux
(guadalinex) using the custom Android kernel the I2C controllers are not
enumerated as ACPI devices as they typically are.
Instead they are enumerated as PCI devices which do not have ACPI firmware
nodes associated with them, so getting the i2c_adapter by the ACPI path of
its firmware node does not work.
Add support for getting the i2c_adapter by the devname() of its PCI parent
instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241104200848.58693-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add get_i2c_adap_by_handle() helper function, this is a preparation patch
for adding support for getting i2c_adapter-s by PCI parent devname().
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241104200848.58693-2-hdegoede@redhat.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Commit df7f9acd86 ("platform/x86: intel: Add 'intel' prefix to the
modules automatically") renames tpmi.c to vsec_tpmi.c in
drivers/platform/x86/intel/, but misses to adjust the INTEL TPMI DRIVER
section, which is referring to this file.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Adjust the file entry to this file renaming.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241105152813.60823-1-lukas.bulwahn@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Because the types of io.regsize and io.regspacing in the ipmipci_probe
function are unsigned int, they should be output in the %u format.
Signed-off-by: liujing <liujing@cmss.chinamobile.com>
Message-ID: <20241106111458.2157-1-liujing@cmss.chinamobile.com>
Signed-off-by: Corey Minyard <corey@minyard.net>
After the following powerpc commits, all calls to set_memory_...()
functions check returned value.
- Commit 8f17bd2f4196 ("powerpc: Handle error in mark_rodata_ro() and
mark_initmem_nx()")
- Commit f7f18e30b4 ("powerpc/kprobes: Handle error returned by
set_memory_rox()")
- Commit 009cf11d4aab ("powerpc: Don't ignore errors from
set_memory_{n}p() in __kernel_map_pages()")
- Commit 9cbacb834b ("powerpc: Don't ignore errors from
set_memory_{n}p() in __kernel_map_pages()")
- Commit 78cb0945f7 ("powerpc: Handle error in mark_rodata_ro() and
mark_initmem_nx()")
All calls in core parts of the kernel also always check returned value,
can be looked at with following query:
$ git grep -w -e set_memory_ro -e set_memory_rw -e set_memory_x -e set_memory_nx -e set_memory_rox `find . -maxdepth 1 -type d | grep -v arch | grep /`
It is now possible to flag those functions with __must_check to make
sure no new unchecked call it added.
Link: https://github.com/KSPP/linux/issues/7
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://patch.msgid.link/775dae48064a661554802ed24ed5bdffe1784724.1725723351.git.christophe.leroy@csgroup.eu
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code which it is referencing does not exist in the same function,
or the file for that matter. Since it was added [1], the Interrupter
Moderation Interval can be changed within xhci addon, e.g. PCI
xhci_pci_setup().
[1], commit 0ebbab3742 ("USB: xhci: Ring allocation and initialization.")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-31-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add xhci_dequeue_td() helper function to reduce code duplication.
Function xhci_dequeue_td() advances the dequeue pointer past the specified
Transfer Descriptor (TD) and releases the TD.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-30-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is modified to return 'void' instead of an integer since it
invariably returns '0'. Additionally, multiple functions which only
return xhci_td_cleanup() are also refactored to return void.
This change eliminates the need for callers to handle a return value that
does not convey meaningful information and improve code readability, as it
becomes immediately clear that the function does not produce a significant
output.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-29-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function td_to_noop() does not utilize arguments 'xhci' and 'ep_ring'.
These unused arguments are removed to clean up the code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant TRB cycle reset, the TRB cycle is already set to zero by
the preceding memset(), making the explicit reset unnecessary.
Clarify ring loop start point. Change the loop start from the dequeue
segment to the start segment. Both approaches achieve the same result,
but starting from the start segment makes it clearer that the entire ring
is being zeroed out.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'max_interrupters' contains the maximum supported interrupters
or the maximum interrupters the user has requested. Thus, it should be
used instead of HCS_MAX_INTRS().
User set 'max_interrupters' value is validated in xhci_gen_setup(),
otherwise 'max_interrupters' value is 'HCS_MAX_INTRS(xhci->hcs_params1)'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is old and seldom seen, as a result the trace is changed
to debug message and only printed when the quirk is set.
Move it into xhci_gen_setup() where the majority of quirks are set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old names:
* start_seg - last_trb_seg
* first_trb - last_trb
New names:
* start_seg - end_seg
* start_trb - end_trb
A Transfer Descriptor (TD) in the xhci driver is a data structure that
represents a single transaction to be performed by the USB host controller.
This transaction is defined by TRBs from 'start_trb' in 'start_seg' to
'end_trb' in 'end_seg'.
The terms "start" and "end" were chosen over "first" and "last" for ease
of searching within the codebase. The ring structure uses 'first_seg' and
'last_seg', while the TD structure uses 'start_seg' and 'end_seg'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions of vendor IDs follow the pattern PCI_VENDOR_ID_#vendor,
while device IDs — PCI_DEVICE_ID_#vendor_#device.
Update the ETRON device IDs to follow the above mentioned pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors"), unplugging USB device while enumeration results in
errors like this:
[ 364.855321] xhci_hcd 0000:0b:00.0: ERROR Transfer event for disabled endpoint slot 5 ep 2
[ 364.864622] xhci_hcd 0000:0b:00.0: @0000002167656d70 67f03000 00000021 0c000000 05038001
[ 374.934793] xhci_hcd 0000:0b:00.0: Abort failed to stop command ring: -110
[ 374.958793] xhci_hcd 0000:0b:00.0: xHCI host controller not responding, assume dead
[ 374.967590] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[ 374.973984] xhci_hcd 0000:0b:00.0: Timeout while waiting for configure endpoint command
Seems that Etorn xHCI host can not perform Soft Retry correctly, apply
XHCI_NO_SOFT_RETRY quirk to disable Soft Retry and then issue is gone.
This patch depends on commit a4a251f8c2 ("usb: xhci: do not perform
Soft Retry for some xHCI hosts").
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performing a stability stress test on a USB3.0 2.5G ethernet adapter
results in errors like this:
[ 91.441469] r8152 2-3:1.0 eth3: get_registers -71
[ 91.458659] r8152 2-3:1.0 eth3: get_registers -71
[ 91.475911] r8152 2-3:1.0 eth3: get_registers -71
[ 91.493203] r8152 2-3:1.0 eth3: get_registers -71
[ 91.510421] r8152 2-3:1.0 eth3: get_registers -71
The r8152 driver will periodically issue lots of control-IN requests
to access the status of ethernet adapter hardware registers during
the test.
This happens when the xHCI driver enqueue a control TD (which cross
over the Link TRB between two ring segments, as shown) in the endpoint
zero's transfer ring. Seems the Etron xHCI host can not perform this
TD correctly, causing the USB transfer error occurred, maybe the upper
driver retry that control-IN request can solve problem, but not all
drivers do this.
| |
-------
| TRB | Setup Stage
-------
| TRB | Link
-------
-------
| TRB | Data Stage
-------
| TRB | Status Stage
-------
| |
To work around this, the xHCI driver should enqueue a No Op TRB if
next available TRB is the Link TRB in the ring segment, this can
prevent the Setup and Data Stage TRB to be breaked by the Link TRB.
Check if the XHCI_ETRON_HOST quirk flag is set before invoking the
workaround in xhci_queue_ctrl_tx().
Fixes: d0e96f5a71 ("USB: xhci: Control transfer support.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the hub driver does not recognize the USB device connected
to the external USB2.0 hub when the system resumes from S4.
After the SetPortFeature(PORT_RESET) request is completed, the hub
driver calls the HCD reset_device callback, which will issue a Reset
Device command and free all structures associated with endpoints
that were disabled.
This happens when the xHCI driver issue a Reset Device command to
inform the Etron xHCI host that the USB device associated with a
device slot has been reset. Seems that the Etron xHCI host can not
perform this command correctly, affecting the USB device.
To work around this, the xHCI driver should obtain a new device slot
with reference to commit 651aaf36a7 ("usb: xhci: Handle USB transaction
error on address command"), which is another way to inform the Etron
xHCI host that the USB device has been reset.
Add a new XHCI_ETRON_HOST quirk flag to invoke the workaround in
xhci_discover_or_reset_device().
Fixes: 2a8f82c4ce ("USB: xhci: Notify the xHC when a device is reset.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine two if statements, because these hosts have the same
quirk flags applied.
[Mathias: has stable tag because other fixes in series depend on this]
Fixes: 91f7a1524a ("xhci: Apply broken streams quirk to Etron EJ188 xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A ring consists of a list of segments, each containing a specific number of
TRBs. The xhci driver allocates and initializes ring segments and TRBs in
the same functions. This combined allocation and initialization process
leads to an issue where, after hibernation (S4 state), the xhci driver
frees all its memory and re-creates the rings, segments, and TRBs from
scratch.
Move all default ring segment initialization into function
xhci_initialize_ring_segments(). This function can be called to
reinitialize a ring without freeing and reallocating it.
Since xhci_alloc_segments_for_ring() no longer initializes segment TRBs,
xhci_initialize_ring_segments() is added to xhci_ring_expansion(). This
results in the last segment of the source ring having the 'LINK_TOGGLE'
bit set. Therefore, if the last source ring segment is not the last in
the destination ring, the 'LINK_TOGGLE' bit must be cleared.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
