dtbs_check was moaning about twl6030-power, use the standard property
instead.
Apparently that twl6030 power snippet slipped in without the
corresponding driver. Now it is handled by the standard property.
CC: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Link: https://lore.kernel.org/r/20240915193527.1071792-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit b9bf561261 ("ARM: dts: am335x-bone-common: Increase MDIO
reset deassert time") already increased the MDIO reset deassert delay
from 6.5 to 13 ms, but this may still cause Ethernet PHY probe failures:
SMSC LAN8710/LAN8720 4a101000.mdio:00: probe with driver SMSC LAN8710/LAN8720 failed with error -5
On BeagleBone Black Rev. C3, ETH_RESETn is controlled by an open-drain
AND gate. It is pulled high by a 10K resistor, and has a 4.7µF
capacitor to ground, giving an RC time constant of 47ms. As it takes
0.7RC to charge the capacitor above the threshold voltage of a CMOS
input (VDD/2), the delay should be at least 33ms. Considering the
typical tolerance of 20% on capacitors, 40ms would be safer. Add an
additional safety margin and settle for 50ms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/9002a58daa1b2983f39815b748ee9d2f8dcc4829.1730366936.git.geert+renesas@glider.be
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- sdhci-pci-gli: A couple of fixes for low power mode on GL9767
-----BEGIN PGP SIGNATURE-----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=zGYd
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull mmc fixes from Ulf Hansson:
- sdhci-pci-gli: A couple of fixes for low power mode on GL9767
* tag 'mmc-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci-gli: GL9767: Fix low power mode in the SD Express process
mmc: sdhci-pci-gli: GL9767: Fix low power mode on the set clock function
Reorganize the introduction to the kernel-parameters file to place
related paragraphs together:
- move module info together and near the beginning
- add a Special Handling section for dashes, underscores, double quotes,
cpu lists, and metric (KMG) suffixes. Expand the KMG suffixes to
include TPE as well.
- add a Kernel Build Options section
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20241029180320.412629-1-rdunlap@infradead.org
The static inline btf_type_is_struct_ptr() function calls
btf_type_skip_modifiers() which is guarded by CONFIG_BPF_SYSCALL.
btf_type_is_struct_ptr() is also only called by CONFIG_BPF_SYSCALL
ifdef code, so let's only expose btf_type_is_struct_ptr() if
CONFIG_BPF_SYSCALL is defined.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Link: https://lore.kernel.org/r/20241104060300.421403-1-alistair.francis@wdc.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This pull request fixes a race condition between tpm_pm_suspend() and
tpm_hwrng_read() (I think for good now):
https://bugzilla.kernel.org/show_bug.cgi?id=219383
BR, Jarkko
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRE6pSOnaBC00OEHEIaerohdGur0gUCZygPzAAKCRAaerohdGur
0pVIAQCiPAk03Cz7cHmeDfWr19VJfazDdqYSfm2muGkrK1HamQEAhbruhFlAWChZ
G6PGBppQkGmGcwLk4LneGtr4FX7yPwY=
=6DaV
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-next-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fix from Jarkko Sakkinen:
"Fix a race condition between tpm_pm_suspend() and tpm_hwrng_read() (I
think for good now)"
* tag 'tpmdd-next-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Lock TPM chip in tpm_pm_suspend() first
Correct the workload setting in order not to mix the setting
with the end user. Update the workload mask accordingly.
v2: changes as below:
1. the end user can not erase the workload from driver except default workload.
2. always shows the real highest priority workoad to the end user.
3. the real workload mask is combined with driver workload mask and end user workload mask.
v3: apply this to the other ASICs as well.
v4: simplify the code
v5: refine the code based on the review comments.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8cc438be5d)
Cc: stable@vger.kernel.org # 6.11.x
always pick the pptable from IFWI on smu v14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 136ce12bd5)
Cc: stable@vger.kernel.org # 6.11.x
acpi_evaluate_object() may return AE_NOT_FOUND (failure), which
would result in dereferencing buffer.pointer (obj) while being NULL.
Although this case may be unrealistic for the current code, it is
still better to protect against possible bugs.
Bail out also when status is AE_NOT_FOUND.
This fixes 1 FORWARD_NULL issue reported by Coverity
Report: CID 1600951: Null pointer dereferences (FORWARD_NULL)
Signed-off-by: Antonio Quartulli <antonio@mandelbit.com>
Fixes: c9b7c809b8 ("drm/amd: Guard against bad data for ATIF ACPI method")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241031152848.4716-1-antonio@mandelbit.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 91c9e221fe)
Cc: stable@vger.kernel.org
An upstream bug report suggests that there are production dGPUs that are
older than DCN401 but still have a umc_info in VBIOS tables with the
same version as expected for a DCN401 product. Hence, reading this
tables should be guarded with a version check.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3678
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2551b4a321)
Fixes: 00c391102a ("drm/amd/display: Add misc DC changes for DCN401")
Cc: stable@vger.kernel.org # 6.11.x
[Why]
During boot up and resume the DC layer will reset the panel
brightness to fix a flicker issue.
It will cause the dm->actual_brightness is not the current panel
brightness level. (the dm->brightness is the correct panel level)
[How]
Set the backlight level after do the set mode.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: d9e865826c ("drm/amd/display: Simplify brightness initialization")
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3655
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7875afafba)
Cc: stable@vger.kernel.org
max_zone_append_sectors differs from all other queue limits in that the
final value used is not stored in the queue_limits but needs to be
obtained using queue_limits_max_zone_append_sectors helper. This not
only adds (tiny) extra overhead to the I/O path, but also can be easily
forgotten in file system code.
Add a new max_hw_zone_append_sectors value to queue_limits which is
set by the driver, and calculate max_zone_append_sectors from that and
the other inputs in blk_validate_zoned_limits, similar to how
max_sectors is calculated to fix this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104073955.112324-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the lock layer zone append emulation, we are now always setting a
max_zone_append_sectors value for zoned devices and this check can't
ever trigger.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104073955.112324-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Listing every single features that needs to be pre-set by stacking
drivers does not scale.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104054218.45596-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Correct the workload setting in order not to mix the setting
with the end user. Update the workload mask accordingly.
v2: changes as below:
1. the end user can not erase the workload from driver except default workload.
2. always shows the real highest priority workoad to the end user.
3. the real workload mask is combined with driver workload mask and end user workload mask.
v3: apply this to the other ASICs as well.
v4: simplify the code
v5: refine the code based on the review comments.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Populate the compatible NPS modes also for providing partition
configuration details through sysfs.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For RAS errors, source of error is known. Skip the core dump of IP
states.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make amdgpu_gfx_sysfs_init/fini functions as common entry points for all
gfx related sysfs nodes.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add nps_mode in RAS init_flag.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Userspace wants to run jobs on a specific sdma ring for verification purposes.
This debugfs entry helps to disable or enable submitting jobs to a specific ring.
This entry is populated only if there are at least two or more cores in the sdma ip.
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
compute/gfx may have multiple rings on some hardware.
In some cases, userspace wants to run jobs on a specific ring for validation purposes.
This debugfs entry helps to disable or enable submitting jobs to a specific ring.
This entry is populated only if there are at least two or more cores in the gfx/compute ip.
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the dma_map_page_attrs() with DMA_ATTR_SKIP_CPU_SYNC
attribute setting to handle the dummy page overlapping
mappings.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under sriov, host driver will save and restore vf pci cfg space during
reset. And during device init, under sriov, pci_restore_state happens after
fullaccess released, and it can have race condition with mmio protection
enable from host side leading to missing interrupts.
So skip amdgpu_device_cache_pci_state for sriov.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The `kfd_get_cu_occupancy` function previously declared a large
`cu_occupancy` array as a local variable, which could lead to stack
overflows due to excessive stack usage. This commit replaces the static
array allocation with dynamic memory allocation using `kcalloc`,
thereby reducing the stack size.
This change avoids the risk of stack overflows in kernel space, in
scenarios where `AMDGPU_MAX_QUEUES` is large. The allocated memory is
freed using `kfree` before the function returns to prevent memory
leaks.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_process.c: In function ‘kfd_get_cu_occupancy’:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_process.c:322:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
322 | }
| ^
Fixes: 6ae9e1aba9 ("drm/amdkfd: Update logic for CU occupancy calculations")
Cc: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
always pick the pptable from IFWI on smu v14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
acpi_evaluate_object() may return AE_NOT_FOUND (failure), which
would result in dereferencing buffer.pointer (obj) while being NULL.
Although this case may be unrealistic for the current code, it is
still better to protect against possible bugs.
Bail out also when status is AE_NOT_FOUND.
This fixes 1 FORWARD_NULL issue reported by Coverity
Report: CID 1600951: Null pointer dereferences (FORWARD_NULL)
Signed-off-by: Antonio Quartulli <antonio@mandelbit.com>
Fixes: c9b7c809b8 ("drm/amd: Guard against bad data for ATIF ACPI method")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241031152848.4716-1-antonio@mandelbit.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head pointer, the driver uses the TX FIFO's tail
pointer instead, assuming that send frames are completed. However the
check for the TEF being full was not correct. This leads to the driver
stop working if the TEF is full.
Fix the TEF full check by assuming that if, from the driver's point of
view, there are no free TX buffers in the chip and the TX FIFO is
empty, all messages must have been sent and the TEF must therefore be
full.
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Closes: https://patch.msgid.link/FR3P281MB155216711EFF900AD9791B7ED9692@FR3P281MB1552.DEUP281.PROD.OUTLOOK.COM
Fixes: b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241104-mcp251xfd-fix-length-calculation-v3-1-608b6e7e2197@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 50ea5449c5 ("can: mcp251xfd: fix ring configuration
when switching from CAN-CC to CAN-FD mode"), the current ring and
coalescing configuration is passed to can_ram_get_layout(). That fixed
the issue when switching between CAN-CC and CAN-FD mode with
configured ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq).
However 50ea5449c5 ("can: mcp251xfd: fix ring configuration when
switching from CAN-CC to CAN-FD mode"), introduced a regression when
switching CAN modes with disabled coalescing configuration: Even if
the previous CAN mode has no coalescing configured, the new mode is
configured with active coalescing. This leads to delayed receiving of
CAN-FD frames.
This comes from the fact, that ethtool uses usecs = 0 and max_frames =
1 to disable coalescing, however the driver uses internally
priv->{rx,tx}_obj_num_coalesce_irq = 0 to indicate disabled
coalescing.
Fix the regression by assigning struct ethtool_coalesce
ec->{rx,tx}_max_coalesced_frames_irq = 1 if coalescing is disabled in
the driver as can_ram_get_layout() expects this.
Reported-by: https://github.com/vdh-robothania
Closes: https://github.com/raspberrypi/linux/issues/6407
Fixes: 50ea5449c5 ("can: mcp251xfd: fix ring configuration when switching from CAN-CC to CAN-FD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241025-mcp251xfd-fix-coalesing-v1-1-9d11416de1df@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), OF
can be enabled on all architectures. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20241022130439.70d016e9@endymion.delvare
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Rockchip CAN-FD controller is only present on Rockchip SoCs. Hence
add a dependency on ARCH_ROCKCHIP, to prevent asking the user about
this driver when configuring a kernel without Rockchip platform
support.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/a4b3c8c1cca9515e67adac83af5ba1b1fab2fcbc.1727169288.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The c_can_handle_bus_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission. The patch fixes the issue by incrementing the
appropriate counter based on the type of error.
Fixes: 881ff67ad4 ("can: c_can: Added support for Bosch C_CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241014135319.2009782-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit b382380c0d ("can: m_can: Add hrtimer to generate software
interrupt") support for IRQ-less devices was added. Instead of an
interrupt, the interrupt routine is called by a hrtimer-based polling
loop.
That patch forgot to change free_irq() to be only called for devices
with IRQs. Fix this, by calling free_irq() conditionally only if an
IRQ is available for the device (and thus has been requested
previously).
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20240930-m_can-cleanups-v1-1-001c579cdee4@pengutronix.de
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for respecting the max-link-speed devicetree property,
forcing a maximum speed (Gen) for a PCI-Express port.
Since the MediaTek PCIe Gen3 controllers also expose the maximum
supported link speed in the PCIE_BASE_CFG register, if property
max-link-speed is specified in devicetree, validate it against the
controller capabilities and proceed setting the limitations only
if the wanted Gen is lower than the maximum one that is supported
by the controller itself (otherwise it makes no sense!).
Link: https://lore.kernel.org/r/20241104114935.172908-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[kwilczynski: change dev_dbg() to dev_info() and update message wording]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: 0710c1ce50 ("ACPI: battery: initialize mutexes through devm_ APIs")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20241030162754.2110946-1-andriy.shevchenko@linux.intel.com
[ rjw: Added 2 empty code lines ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ISA variable is only defined if X86_32 is also defined. However,
these drivers are still useful and in use on at least some modern 64-bit
x86 industrial systems as well. With the correct module parameters, they
work as long as IO port communication is possible, despite their name
having ISA in them.
Fixes: a29689e60e ("net: handle HAS_IOPORT dependencies")
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Link: https://patch.msgid.link/20240919174151.15473-2-tmuehlbacher@posteo.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The description of PDU1 format usage mistakenly referred to PDU2 format.
Signed-off-by: Alexander Hölzl <alexander.hoelzl@gmx.net>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20241023145257.82709-1-alexander.hoelzl@gmx.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[Why]
1. HDMI does not have 6 bpc support. Having 6 bpc pass validation
does not comply with spec.
2. Validate 420 only for native HDMI, but not apply to pcon use
case.
3. Current mode validation log is not readable.
[how]
1. Cap 8 bpc for dp-hdmi converter.
2. Validate yuv420 for pcon use case as well,
if rgb/yuv444 8bpc cannot fit into pcon bw limitation of
the link from the converter to HDMI sink.
3. Add readable pixel_format and color_depth into debug log.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement the new backlight_level_params structure as part of the VBAC
framework, the information in this structure is needed to be passed down
to the DMCUB to identify the backlight control type, to adjust the
backlight of the panel and to perform any required conversions from PWM
to nits or vice versa.
[How]
Modified existing functions to include the new backlight_level_params
structure.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Kaitlyn Tse <Kaitlyn.Tse@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add device ID for dual-core Kaby Lake-S processors e.g. i3-7100.
Signed-off-by: James Ye <jye836@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Jason Baron <jbaron@akamai.com>
Link: https://lore.kernel.org/r/20240824120622.46226-1-jye836@gmail.com
Add a mising reg field to the autogenerated header for future use
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add an instance parameter to the existing function dpm_set_vcn_enable()
for future implementation. Re-write all pptable functions accordingly.
v2: Remove duplicated dpm_set_vcn_enable() functions in v1. Instead,
adding instance parameter to existing functions.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Out-of-bounds access occurs if the fast device is expanded unexpectedly
before the first-time resume of the cache table. This happens because
expanding the fast device requires reloading the cache table for
cache_create to allocate new in-core data structures that fit the new
size, and the check in cache_preresume is not performed during the
first resume, leading to the issue.
Reproduce steps:
1. prepare component devices:
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 65536 linear /dev/sdc 8192"
dmsetup create corig --table "0 524288 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
2. load a cache table of 512 cache blocks, and deliberately expand the
fast device before resuming the cache, making the in-core data
structures inadequate.
dmsetup create cache --notable
dmsetup reload cache --table "0 524288 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
dmsetup reload cdata --table "0 131072 linear /dev/sdc 8192"
dmsetup resume cdata
dmsetup resume cache
3. suspend the cache to write out the in-core dirty bitset and hint
array, leading to out-of-bounds access to the dirty bitset at offset
0x40:
dmsetup suspend cache
KASAN reports:
BUG: KASAN: vmalloc-out-of-bounds in is_dirty_callback+0x2b/0x80
Read of size 8 at addr ffffc90000085040 by task dmsetup/90
(...snip...)
The buggy address belongs to the virtual mapping at
[ffffc90000085000, ffffc90000087000) created by:
cache_ctr+0x176a/0x35f0
(...snip...)
Memory state around the buggy address:
ffffc90000084f00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc90000084f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
>ffffc90000085000: 00 00 00 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8
^
ffffc90000085080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc90000085100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
Fix by checking the size change on the first resume.
Signed-off-by: Ming-Hung Tsai <mtsai@redhat.com>
Fixes: f494a9c6b1 ("dm cache: cache shrinking support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
When shrinking the fast device, dm-cache iteratively searches for a
dirty bit among the cache blocks to be dropped, which is less efficient.
Use find_next_bit instead, as it is twice as fast as the iterative
approach with test_bit.
Signed-off-by: Ming-Hung Tsai <mtsai@redhat.com>
Fixes: f494a9c6b1 ("dm cache: cache shrinking support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
An unexpected WARN_ON from flush_work() may occur when cache creation
fails, caused by destroying the uninitialized delayed_work waker in the
error path of cache_create(). For example, the warning appears on the
superblock checksum error.
Reproduce steps:
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 65536 linear /dev/sdc 8192"
dmsetup create corig --table "0 524288 linear /dev/sdc 262144"
dd if=/dev/urandom of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 524288 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
Kernel logs:
(snip)
WARNING: CPU: 0 PID: 84 at kernel/workqueue.c:4178 __flush_work+0x5d4/0x890
Fix by pulling out the cancel_delayed_work_sync() from the constructor's
error path. This patch doesn't affect the use-after-free fix for
concurrent dm_resume and dm_destroy (commit 6a459d8edb ("dm cache: Fix
UAF in destroy()")) as cache_dtr is not changed.
Signed-off-by: Ming-Hung Tsai <mtsai@redhat.com>
Fixes: 6a459d8edb ("dm cache: Fix UAF in destroy()")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
When creating a cache device, the actual size of the cache origin might
be greater than the specified cache target length. In such case, the
number of origin blocks should match the cache target length, not the
full size of the origin device, since access beyond the cache target is
not possible. This issue occurs when reducing the origin device size
using lvm, as lvreduce preloads the new cache table before resuming the
cache origin, which can result in incorrect sizes for the discard bitset
and smq hotspot blocks.
Reproduce steps:
1. create a cache device consists of 4096 origin blocks
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 65536 linear /dev/sdc 8192"
dmsetup create corig --table "0 524288 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 524288 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
2. reduce the cache origin to 2048 oblocks, in lvreduce's approach
dmsetup reload corig --table "0 262144 linear /dev/sdc 262144"
dmsetup reload cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
dmsetup suspend cache
dmsetup suspend corig
dmsetup suspend cdata
dmsetup suspend cmeta
dmsetup resume corig
dmsetup resume cdata
dmsetup resume cmeta
dmsetup resume cache
3. shutdown the cache, and check the number of discard blocks in
superblock. The value is expected to be 2048, but actually is 4096.
dmsetup remove cache corig cdata cmeta
dd if=/dev/sdc bs=1c count=8 skip=224 2>/dev/null | hexdump -e '1/8 "%u\n"'
Fix by correcting the origin_blocks initialization in cache_create and
removing the unused origin_sectors from struct cache_args accordingly.
Signed-off-by: Ming-Hung Tsai <mtsai@redhat.com>
Fixes: c6b4fcbad0 ("dm: add cache target")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
If the user sets panic_on_error and doesn't set panic_on_corruption,
dm-verity should not panic on data mismatch. But, currently it panics,
because it treats data mismatch as I/O error.
This commit fixes the logic so that if there is data mismatch and
panic_on_corruption or restart_on_corruption is not selected, the system
won't restart or panic.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Fixes: f811b83879 ("dm-verity: introduce the options restart_on_error and panic_on_error")
