This commit refactors the check for missing configuration files, making
it easier to add more files to the list.
The format of the error message has been slightly changed, as follows:
[Before]
ERROR: Kernel configuration is invalid.
include/generated/autoconf.h or include/config/auto.conf are missing.
Run 'make oldconfig && make prepare' on kernel src to fix it.
[After]
***
*** ERROR: Kernel configuration is invalid. The following files are missing:
*** - include/generated/autoconf.h
*** - include/config/auto.conf
*** Run "make oldconfig && make prepare" on kernel source to fix it.
***
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Commit e68a558fb2 ("speakup: Fix building as extmod") was intended
to support building this as an external module.
Since commit b1992c3772 ("kbuild: use $(src) instead of
$(srctree)/$(src) for source directory"), $(src) consistently points
to the source directory, regardless of whether it is compiled as an
external module or not.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default we expect all i2c nodes to be single-master, we do not have
any module or carrier board that uses multi-master mode on any i2c
controller. With this property set, we benefit from optimisations made
exclusively for single-masters.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default we expect all i2c nodes to be single-master, we do not have
any module or carrier board that uses multi-master mode on any i2c
controller. With this property set, we benefit from optimisations made
exclusively for single-masters.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI connector on the board is a micro-HDMI (type "d")
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The first argument of lpcg should indices, instead of index. Fix it by
use predefined macro.
Fixes: 9f7053f67c ("arm64: dts: imx8-ss-hsio: Add PCIe and SATA support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update clock settings to use the macro IMX_LPCG_CLK_0 instead of the
hardcoded value 0. The first argument of lpcg is indices, not index.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
{'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
is valid under each of {'required': ['output-low']}, {'required': ['output-high']
Fixes: 3f6fc30abe ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In jedec,spi-nor.yaml:
SPI NOR flashes compatible with the JEDEC SFDP standard or which may be
identified with the READ ID opcode (0x9F) do not deserve a specific
compatible. They should instead only be matched against the generic
"jedec,spi-nor" compatible.
en25s64 already in drivers/mtd/spi-nor/eon.c. So remove it safely and fix
below warning:
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: flash@2: compatible: 'oneOf' conditional failed, one must be fixed:
['en25s64', 'jedec,spi-nor'] is too long
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the touchscreen power-supply from 'power-supply' to 'AVDD28-supply' and
'VDDIO-supply' as per the binding documentation in goodix.yaml.
Fix below warning:
arch/arm64/boot/dts/freescale/imx8mp-kontron-dl.dtb: touchscreen@5d:
'power-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/input/touchscreen/goodix.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds the DTSI file for the Nitrogen8MP SMARC System on Module which
is delivered with the Nitrogen8MP Universal SMARC Carrier Board.
Initial support includes:
- Serial console
- eMMC
- SD card
Signed-off-by: Bhavin Sharma <bhavin.sharma@siliconsignals.io>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move 'samsung,burst-clock-frequency' and 'samsung,esc-clock-frequency'
properties to i.MX8MN and i.MX8MM mba8mx board file. These properties are
not applicable to i.MX8MQ MIPI DSI, which uses the compatible string
'fsl,imx8mq-nwl-dsi'. The properties are only valid for i.MX8MM and i.MX8MN
devices with the compatible string 'fsl,imx8mm-mipi-dsim', as described in
samsung,mipi-dsim.yaml.
Fix warning:
arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx-lvds-tm070jvhg33.dtb: dsi@30a00000:
Unevaluated properties are not allowed ('ports', 'samsung,burst-clock-frequency', 'samsung,esc-clock-frequency' were unexpected)
from schema $id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'data-lanes' is port0 of lvds bridge. Needn't set it for simple panel. Fix
below CHECK_DTBS warning:
arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx-lvds-tm070jvhg33.dtb:
panel-lvds: port:endpoint: Unevaluated properties are not allowed ('data-lanes' was unexpected)
from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks GW82XX-2X is an ARM based single board computer (SBC)
comprised of the i.MX8M Plus based gw702x SoM and the gw82xx baseboard
featuring:
- i.MX8M Plus SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (GSC)
- microSD (1.8V/3.3V Capable)
- panel status bi-color LED
- pushbutton switch
- fan controller with tachometer
- USB Type-C connector
- PCIe switch
- 2x GbE RJ45 connectors
- multi-protocol RS232/RS485/RS422 Serial ports
- 2x Flexible Socket Adapters with SDIO/UART/USB/PCIe
(for M.2 and miniPCIe expansion)
- 2x isolated CAN
- GPS
- accelerometer
- magnetometer
- off-board connectors for: SPI, GPIO, I2C, ADC
- Wide range DC power input
- support for 802.3at PoE (via adapter)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add edma1, sai4, sai5 device nodes bus of in per_bridge3.
Add edma2, sai6, sai7, spdif device nodes in bus of
per_bridge5.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set the status of the dsp node to "okay" and assign and add its reserved
memory regions.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT node for i.MX8QM's DSP, which is found in the VPU subsystem.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8QM, the DSP is in the VPU subsystem, which means that using the
'dsp' node from 'imx8-ss-audio.dtsi' is wrong as it's placed under the
wrong bus. As such, drop it.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing dsp rproc-related reserved memory regions and assign them to
the 'dsp' node.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'dsp' node is currently configured for running an audio firmware.
Since the firmware requires that some audio-related IPs be disabled in
Linux, this will clash with the configurations from the imx8 board DTs
(i.e: imx8qm-mek, imx8qxp-mek, etc...), thus making the dsp unusable
(since the firmware won't function properly).
To avoid this issue, configure the 'dsp' node for rproc. This way, users
will be able to use the dsp alongside the board-level audio configuration
as long as the firmware doesn't need the audio IPs.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Tested-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Changes in Dynamic Range and Mastering infoframe
should not trigger a full modeset. Therefore, allow
fastset. DP SDP programming is already hooked up in the
fastset flow but HDMI AVI infoframe update is not, add it.
Any other infoframe that can be fastset should be added to
the helper intel_hdmi_fastset_infoframes().
v3:
- Create a wrapper intel_ddi_update_pipe_hdmi to stick to
uniform naming (Jani)
- Do not disable HDMI AVI infoframe if already disabled (Uma)
v2:
- Update HDMI AVI infoframe during fastset.
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023044122.3889137-1-chaitanya.kumar.borah@intel.com
We are currently seeing unexpected link trainings with several different
eDP panels. These are caused by these panels stating bad link status in
their dpcd registers. This can be observed by doing following test:
1. Boot up without Xe module loaded
2. Load Xe module with PSR disabled:
$ modprobe xe enable_psr=0
3. Read panel link status register
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 00
4. Enable PSR, sleep for 2 seconds and disable PSR again:
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ echo "-1" > /sys/kernel/debug/dri/0000:00:02.0/xe_params/enable_psr
$ echo 0x0 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
$ sleep 2
$ cat /sys/kernel/debug/dri/0/i915_edp_psr_status | grep status
$ echo 0x1 > /sys/kernel/debug/dri/0/i915_edp_psr_debug
Source PSR/PanelReplay status: DEEP_SLEEP [0x80310030]
5. Now read panel link status registers again:
$ dpcd_reg read --offset 0x200e --count=1
0x200e: 80
Workaround this by not trusting link status registers after PSR is enabled
until first short pulse interrupt is received.
v2:
- clear link_ok flag on pipe disable
- remove useless comment
- modify intel_dp_needs_link_retrain return statement
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029122415.1789528-1-jouni.hogander@intel.com
Backmerging to get up-to-date and to bring in a fix that was
merged through drm-misc-fixes.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
pcim_iomap_regions() and pcim_iomap_table() have been deprecated in
commit e354bb84a4 ("PCI: Deprecate pcim_iomap_table(),
pcim_iomap_regions_request_all()"). Replace these functions with
pcim_iomap_region().
In order to match the rest of the code in idio_24_probe(), utilize
dev_err_probe() to handle error for pcim_enable_device().
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241101-pci_iomap_region_gpio_acces-v1-2-26eb1dc93e45@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
pcim_iomap_regions() and pcim_iomap_table() have been deprecated in
commit e354bb84a4 ("PCI: Deprecate pcim_iomap_table(),
pcim_iomap_regions_request_all()"). Replace these functions with
pcim_iomap_region().
In order to match the rest of the code in idio_16_probe(), utilize
dev_err_probe() to handle error for pcim_enable_device().
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241101-pci_iomap_region_gpio_acces-v1-1-26eb1dc93e45@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIOs used as shared irqs can still be requested by user-space (or
kernel drivers for that matter) yet we report them as used over the
chardev ABI. Drop the test for FLAG_USED_AS_IRQ from
gpio_desc_to_lineinfo().
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241031200842.22712-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In order to emit line-state events on edge changes in sysfs, update the
EDGE flags in the descriptor in gpio_sysfs_request_irq() and emit the
event on a successful store.
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20241031-gpio-notify-sysfs-v4-5-142021c2195c@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The sysfs active_low attribute doesn't go through the usual paths so it
doesn't emit the line-state event. Add the missing call to
gpiod_line_state_notify() to gpio_sysfs_set_active_low().
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20241031-gpio-notify-sysfs-v4-4-142021c2195c@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We already emit a CONFIG_RELEASED event when a line is unexported over
sysfs (this is handled by gpiod_free()) but we don't do the opposite
when it's exported. This adds the missing call to
gpiod_line_state_notify().
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20241031-gpio-notify-sysfs-v4-3-142021c2195c@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Currently, even though there is a bit to control FEC enable/disable
individually, the FEC Decode Enable sequence is sent by the SOC only
once TRANS_CONF enable is set. This ties the FEC enabling too tightly
to modeset and therefore cannot be re-issued (in case of failure)
without a modeset.
From PTL, FEC_DECODE_EN sequence can be sent to a DPRX independent
of TRANS_CONF enable. This allows us to re-issue an FEC_DECODE_EN
sequence without a modeset. Hence allowing us to have a retry
mechanism in case the DPRX does not respond with an FEC_ENABLE
within certain amount of time.
While at it, replace struct drm_i915_private with struct intel_display
v4:
- More code refactor [Jani]
- use struct intel_display [Jani]
- Optimize logging [Jani]
v3:
- Make the commit message more legible [Jani]
- Refactor code to re-use existing code [Jani]
- Do away with platform dependent FEC enable checks [Jani]
v2:
- Refactor code to avoid duplication and improve readability [Jani]
- In case of PTL, wait for FEC status directly after FEC enable [Srikanth]
- Wait for FEC_ENABLE_LIVE_STATUS to be cleared before
re-enabling FEC [Srikanth]
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241024061002.4085137-1-chaitanya.kumar.borah@intel.com
Add the newline separator before generating the gpio chip entry to make
the code easier to read.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241028125000.24051-4-johan+linaro@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Adds a devicetree for the Kobo Clara 2E Ebook reader. It is based
on boards marked with "37NB-E60K2M+4A2" or "37NB-E60K2M+4B0". It is
equipped with an i.MX6SLL SoC.
Expected to work:
- Buttons
- Wifi
- Bluetooth
(if Wifi is initialized first, driver does not handle regulators
yet)
- LED
- uSD
- USB
- RTC
- Touchscreen
Add human-readable comments for devices without mainlined driver and
binding. Such comments can e.g. be help to find testers if someone
starts to work on the missing drivers.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds compatible strings for the Kobo Clara 2E eBook reader.
There are two variants differing in the EPD PMIC used.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Under certain conditions, the 64-bit '-mstack-protector-guard' flags may
end up in the 32-bit vDSO flags, resulting in build failures due to the
structure of clang's argument parsing of the stack protector options,
which validates the arguments of the stack protector guard flags
unconditionally in the frontend, choking on the 64-bit values when
targeting 32-bit:
clang: error: invalid value 'r13' in 'mstack-protector-guard-reg=', expected one of: r2
clang: error: invalid value 'r13' in 'mstack-protector-guard-reg=', expected one of: r2
make[3]: *** [arch/powerpc/kernel/vdso/Makefile:85: arch/powerpc/kernel/vdso/vgettimeofday-32.o] Error 1
make[3]: *** [arch/powerpc/kernel/vdso/Makefile:87: arch/powerpc/kernel/vdso/vgetrandom-32.o] Error 1
Remove these flags by adding them to the CC32FLAGSREMOVE variable, which
already handles situations similar to this. Additionally, reformat and
align a comment better for the expanding CONFIG_CC_IS_CLANG block.
Cc: stable@vger.kernel.org # v6.1+
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://patch.msgid.link/20241030-powerpc-vdso-drop-stackp-flags-clang-v1-1-d95e7376d29c@kernel.org
Like all other non-ancient Qualcomm clock drivers, QCOM_GDSC is
required, as the GCC driver defines and instantiates a bunch of GDSCs.
Add the missing dependency.
Reported-by: Kamil Gołda <kamil.golda@protonmail.com>
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20241003-topic-6125kconfig-v1-1-f5e1efbff07c@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add LLCC configuration for the QCS8300 platform. There is an errata on
LB_CNT information on QCS8300 platform, hardcode num_banks to get the
correct value.
Signed-off-by: Jingyi Wang <quic_jingyw@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241031-qcs8300_llcc-v3-2-bb56952cb83b@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
