Currently, the driver handles SMPS decisions by tracking AP
capabilities, BT coexistence changes, sending necessary SMPS
frames to the AP, and updating firmware with RX chain info
using the RLC_CONFIG_CMD.
Starting with version 3 of the RLC_CONFIG_CMD, the firmware
takes over this responsibility. It now tracks SMPS, sends
frames, and configures the RLC.
In this patch:
1. Stop sending RLC_CONFIG_CMD when firmware supports RLC
offload (version 3), as rlc.rx_chain_info is not needed by
firmware, and no other field in the cmd is used.
2. Prevent the driver from forwarding any SMPS requests to
mac80211, i.e., the driver should not transmit SMPS frames
to the AP as firmware handles that.
3. Set NL80211_FEATURE_DYNAMIC_SMPS and NL80211_FEATURE_STATIC_SMPS
conditionally based on RLC version.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45da23be1f65.I0d46db82dd990a82e8a66876fe2f5310bc9513be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we had a comeback, we will never use the default timeout values
again because comeback is never cleared.
Clear comeback if we send another association request which will allow
to start a default timer after Tx status.
The problem was seen with iwlwifi where the tx_status on the association
request is handled before the association response frame (which is the
usual case).
1) Tx assoc request 1/3
2) Rx assoc response (comeback, timeout = 1 second)
3) wait 1 second
4) Tx assoc request 2/3
5) Set timer to IEEE80211_ASSOC_TIMEOUT_LONG = 500ms (1 second after
round_up)
6) tx_status on frame sent in 4) is ignored because comeback is still
true
7) AP does not reply with assoc response
8) wait 1s <= This is where the bug is felt
9) Tx assoc request 3/3
With this fix, in step 6 we will reset the timer to
IEEE80211_ASSOC_TIMEOUT_SHORT = 100ms and we will wait only 100ms in
step 8.
Fixes: b133fdf07d ("wifi: mac80211: Skip association timeout update after comeback rejection")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20240808085916.23519-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to RFC8325 4.3, Multimedia Streaming: AF31(011010, 26),
AF32(011100, 28), AF33(011110, 30) maps to User Priority = 4
and AC_VI (Video).
However, the original code remain the default three Most Significant
Bits (MSBs) of the DSCP, which makes AF3x map to User Priority = 3
and AC_BE (Best Effort).
Fixes: 6fdb8b8781 ("wifi: cfg80211: Update the default DSCP-to-UP mapping")
Signed-off-by: hhorace <hhoracehsu@gmail.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20240807082205.1369-1-hhoracehsu@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that functions in lib80211 handle "const struct lib80211_crypto_ops",
some structure can be constified as well.
Constifying these structures moves some data to a read-only section, so
increase overall security.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/dfda6343781ae3d50cd2ec7bbdcf76a489b6922a.1722839425.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that functions in lib80211 handle "const struct lib80211_crypto_ops",
some structure can be constified as well.
Constifying these structures moves some data to a read-only section, so
increase overall security.
Before:
text data bss dec hex filename
7273 604 16 7893 1ed5 net/wireless/lib80211.o
After:
text data bss dec hex filename
7429 444 16 7889 1ed1 net/wireless/lib80211.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc3741c15f2c502cc85bddda9d6582b5977c8f9.1722839425.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lib80211_register_crypto_ops() and lib80211_unregister_crypto_ops() don't
modify their "struct lib80211_crypto_ops *ops" argument. So, it can be
declared as const.
Doing so, some adjustments are needed to also constify some date in
"struct lib80211_crypt_data", "struct lib80211_crypto_alg" and the
return value of lib80211_get_crypto_ops().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c74085e02f33a11327582b19c9f51c3236e85ae2.1722839425.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for moving code to arch/x86/coco/sev/core.c, replace
dev_dbg with pr_debug.
No functional change.
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Peter Gonda <pgonda@google.com>
Link: https://lore.kernel.org/r/20240731150811.156771-2-nikunj@amd.com
Add prints of the per-link MPDU counters, and change the other MPDU
counters related prints to use DL_INFO, which is already used for all
EMLSR tests anyway, instead of DL_STATS which pollutes the logs with all
the RX signal info.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Link: https://patch.msgid.link/20240729201718.02bd85837c87.I85480c9c4fab0f7a574dd69cbeafd82674146921@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a new notification the BT profile. It contains almost nothing,
only the wifi loss information. Copy this into mvm. We still need to
iterate over the vifs / links to use this data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.637499f3a85a.I8bf654cf5d8aa038100273876c936845ecc338f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwl_bt_coex_profile_notif is now being obsoleted. It'll be replaced
by a new notification coming with a non-legacy group. Rename it to avoid
confusion.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.dc29fd0d7817.I5881fce86ec8b76ae98d2948265434b8e7d860c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The algo running in fw may take a little longer than 5 milliseconds,
(e.g. measurement on 80MHz while associated). Increase the minimum
time between measurements to 7 milliseconds.
Fixes: 830aa3e7d1 ("iwlwifi: mvm: add support for range request command version 13")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.d3f3c26e00d9.I09e951290e8a3d73f147b88166fd9a678d1d69ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cipher pointer is not set, but is derefereced trying to set its
content, which leads to a NULL pointer dereference.
Fix it by pointing to the cipher parameter before dereferencing.
Fixes: 626be4bf99 ("wifi: iwlwifi: mvm: modify iwl_mvm_ftm_set_secured_ranging() parameters")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.24e83369f136.I80501ddcb82920561f450d00020d860e7a3f90c6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the upper layer requests to cancel an ongoing scan, a race
is possible in which by the time the driver starts to handle the
upper layers scan cancel flow, the FW already completed handling
the scan request and the driver received the scan complete
notification but still did not handle the notification. In such a
case the FW will simply ignore the scan abort request coming from
the driver, no notification would arrive from the FW and the entire
abort flow would be considered a failure.
To better handle this, check the status code returned by the FW for
the scan abort command. In case the status indicates that
no scan was aborted, complete the scan abort flow with success, i.e.,
the scan was aborted, as the flow is expected to consume the scan
complete notification.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825085558.483989d3baef.I3340556a222388504c6330b333360bf77d10f9e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware needs to know what we had in the HE CAP, propagate that
setting to the firmware through the LINK command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.fef270d2995b.I328237837df30e1cb98764987eaaf8e8993e058c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAP version 4 uses larger Host to MEI notification queue.
Since it is unknown which SAP version is used by the CSME firmware
when the driver loads, try version 4 first. In case the CSME firmware
uses version 3, the memory allocation will fail. In this case the
driver will try again to allocate the memory for version 3.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.8372e040282f.Ia0085784e08a35159c9293f986c3d2774038f4c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'gl' devices are in the bz family, but they're not,
integrated, so should have their own trans config struct.
Fix that, also necessitating the removal of LTR config,
and while at it remove 0x2727 and 0x272D IDs that were
only used for test chips.
Fixes: c30a2a6478 ("wifi: iwlwifi: add a new PCI device ID for BZ device")ticket=none
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.95aed0620080.Ib9129512c95aa57acc9876bdff8b99dd41e1562c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We may want to know the value of this register for certain
debug scenarios before we overwrite it, it indicates which
parts of the chip have recently been reset.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.737e5f8bb8df.Ia3f3637ac4a0fb4b35ffd652f92eb75de652ee12@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cases changed here, key iteration isn't done from
an RCU critical section, but rather using the wiphy lock
as protection. Therefore, just use ieee80211_iter_keys().
The link switch case can therefore also use sync commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.69a2d18580c1.I2148e04d4b467d0b100beac8f7e449bfaaf775a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Rename iwl_dev_tx_power_cmd to iwl_dev_tx_power_cmd_v3_v8
* struct iwl_dev_tx_power_common needs to be packed. It was always the
case, but now that its size is not a multiple of 4, it becomes
meaningful.
* Move per_band data out of the common structure since it won't be
present in the new versions of the command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.8da29a66984f.I922bdef4740d990f98cb452e858c4157bbc491c5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce 'ieee80211_mgmt_ba()' to avoid code duplication between
'ieee80211_send_addba_resp()', 'ieee80211_send_addba_request()',
and 'ieee80211_send_delba()', ensure that all related addresses
are '__aligned(2)', and prefer convenient 'ether_addr_copy()'
over generic 'memcpy()'. No functional changes expected.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240725090925.6022-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct the name field in multi_radio's MODULE_PARM_DESC.
Fixes: d2601e34a1 ("wifi: mac80211_hwsim: add support for multi-radio wiphy")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/20240712074938.26437-1-kevin_yang@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the firmware crashes, we first told the op_mode and only then,
changed the transport's state. This is a problem if the op_mode's
nic_error() handler needs to send a host command: it'll see that the
transport's state still reflects that the firmware is alive.
Today, this has no consequences since we set the STATUS_FW_ERROR bit and
that will prevent sending host commands. iwl_fw_dbg_stop_restart_recording
looks at this bit to know not to send a host command for example.
To fix the hibernation, we needed to reset the firmware without having
an error and checking STATUS_FW_ERROR to see whether the firmware is
alive will no longer hold, so this change is necessary as well.
Change the flow a bit.
Change trans->state before calling the op_mode's nic_error() method and
check trans->state instead of STATUS_FW_ERROR. This will keep the
current behavior of iwl_fw_dbg_stop_restart_recording upon firmware
error, and it'll allow us to call iwl_fw_dbg_stop_restart_recording
safely even if STATUS_FW_ERROR is clear, but yet, the firmware is not
alive.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.9d7427fbdfd7.Ia056ca57029a382c921d6f7b6a6b28fc480f2f22@changeid
[I missed this was a dependency for the hibernation fix, changed
the commit message a bit accordingly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RSN IE missing in beacon is normal in open networks.
Avoid returning -EINVAL in this case.
Steps to reproduce:
$ cat /etc/wpa_supplicant.conf
network={
ssid="testNet"
mode=2
key_mgmt=NONE
}
$ wpa_supplicant -iwlan0 -c /etc/wpa_supplicant.conf
nl80211: Beacon set failed: -22 (Invalid argument)
Failed to set beacon parameters
Interface initialization failed
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
wlan0: Unable to setup interface.
Failed to initialize AP interface
After the change:
$ wpa_supplicant -iwlan0 -c /etc/wpa_supplicant.conf
Successfully initialized wpa_supplicant
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
Cc: stable@vger.kernel.org
Fixes: fe0a7776d4 ("wifi: wfx: fix possible NULL pointer dereference in wfx_set_mfp_ap()")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240823131521.3309073-1-alexander.sverdlin@siemens.com
When resolving name in ceph_dns_resolve_name(), the end address of name
is determined by the minimum value of delim_p and colon_p. So using min()
here is more in line with the context.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Use time_after_eq macro instead of using
jiffies directly to handle wraparound.
[ xiubli: adjust the header files order ]
Signed-off-by: Chen Yufan <chenyufan@vivo.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
These functions is never implemented and used.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Add a method to quickly verify whether safe RET operates properly on
a given system using perf tool.
Also, add a selftest which does the same thing.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240731160531.28640-1-bp@kernel.org
If a function name is greater than 63 characters long, xmon command
may not find them. For example, here is a test that executed an illegal
instruction in a kernel function and one of call stack function has a
name greater than 63 characters long:
cpu 0x0: Vector: 700 (Program Check) at [c00000000a6577e0]
pc: c0000000001aacb8: check__allowed__function__name__for__symbol__r4+0x8/0x10
lr: c00000000019c1e0: check__allowed__function__name__for__symbol__r1+0x20/0x40
sp: c00000000a657a80
msr: 800000000288b033
current = 0xc00000000a439900
paca = 0xc000000003e90000 irqmask: 0x03 irq_happened: 0x01
.....
[link register ] c00000000019c1e0 check__allowed__function__name__for__symbol__r1+0x20/0x40
[c00000000a657a80] c00000000a439900 (unreliable)
[c00000000a657aa0] c0000000001021d8 check__allowed__function__name__for__symbol__r2_resolution_symbol+0x38/0x4c
[c00000000a657ac0] c00000000019b424 power_pmu_event_init+0xa4/0xa50
and when executing a dump instruction (di) command for long function
name, xmon fails to find the function symbol:
0:mon> di $check__allowed__function__name__for__symbol__r2_resolution_symbol
unknown symbol 'check__allowed__function__name__for__symbol__r2_resolution_symb'
0000000000000000 ********
This is because in scanhex(), tmpstr loop index is checked only for
a upper bound of 63.
Fix it by replacing the upper bound value with (KSYM_NAME_LEN-1).
With fix:
0:mon> di $check__allowed__function__name__for__symbol__r2_resolution_symbol
c0000000001021a0 3c4c0249 addis r2,r12,585
c0000000001021a4 3842ae60 addi r2,r2,-20896
c0000000001021a8 7c0802a6 mflr r0
c0000000001021ac 60000000 nop
.....
Reported-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Closes: https://lore.kernel.org/linuxppc-dev/CANiq72=QeTgtZL4k9=4CJP6C_Hv=rh3fsn3B9S3KFoPXkyWk3w@mail.gmail.com/
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240826064217.46658-1-maddy@linux.ibm.com
Everything is now in place for a guest to "enjoy" FP8 support.
Expose ID_AA64PFR2_EL1 to both userspace and guests, with the
explicit restriction of only being able to clear FPMR.
All other features (MTE* at the time of writing) are hidden
and not writable.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-9-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
If userspace has enabled FP8 support (by setting ID_AA64PFR2_EL1.FPMR
to 1), let's enable the feature by setting HCRX_EL2.EnFPM for the vcpu.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-8-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
ID_AA64FPFR0_EL1 contains all sort of bits that contain a description
of which FP8 subfeatures are implemented.
We don't really care about them, so let's just expose that register
and allow userspace to disable subfeatures at will.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-7-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
HCRX_EL2.EnFPM controls the trapping of FPMR (as well as the validity
of any FP8 instruction, but we don't really care about this last part).
Describe the trap bit so that the exception can be reinjected in a
NV guest.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-6-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Just like the rest of the FP/SIMD state, FPMR needs to be context
switched.
The only interesting thing here is that we need to treat the pKVM
part a bit differently, as the host FP state is never written back
to the vcpu thread, but instead stored locally and eagerly restored.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-5-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Just like SVCR, FPMR is currently stored at the wrong location.
Let's move it where it belongs.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we are about to check for the advertisement of FPMR support to
a guest in a number of places, add a predicate that will gate most
of the support code for FPMR.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
SVCR is just a system register, and has no purpose being outside
of the sysreg array. If anything, it only makes it more difficult
to eventually support SME one day. If ever.
Move it into the array with its little friends, and associate it
with a visibility predicate.
Although this is dead code, it at least paves the way for the
next set of FP-related extensions.
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240820131802.3547589-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
As the last-standing user of PCM vmalloc buffer helper API took its
own buffer management, we can finally drop those API functions, which
were leftover after reorganization of ALSA memalloc code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807152725.18948-3-tiwai@suse.de
The dw-hdmi drm bridge driver is the only one who still uses the ALSA
vmalloc helper API functions. A previous attempt to change the way of
buffer management wasn't taken for this legacy stuff, as we had little
chance for test and some risk of major breaking.
Instead, this patch moves the vmalloc buffer stuff into the dw-hdmi
driver code itself, so that we can drop them from ALSA core code
afterwards.
There should be no functional changes.
Link: https://lore.kernel.org/20191210154536.29819-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807152725.18948-2-tiwai@suse.de
Florian Westphal says:
====================
Policy insertions do not scale well, due to both a lienar list walk
to find the insertion spot and another list walk to set the 'pos' value
(a tie-breaker to detect which policy is older when there is ambiguity
as to which one should be matched).
First patch gets rid of the second list walk on insert.
Rest of the patches get rid of the insertion walk.
This list walk was only needed because when I moved the policy db
implementation to rbtree I retained the old insertion method for the
sake of XFRM_MIGRATE.
Switching that to tree-based lookup avoids the need for the full
list search.
After this, insertion of a policy is largely independent of the number
of pre-existing policies as long as they do not share the same source/
destination networks.
Note that this is compile tested only as I did not find any
tests for XFRM_MIGRATE.
====================
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZsxg5QAKCRCRxhvAZXjc
olSiAQDvFvim4YtMmUDagC3yWTBsf+o3lYdAIuzNE0NtSn4vpAEAl/HVhQCaEDjv
mcE3jokEsbvyXLnzs78PrY0Heua2mQg=
=AHAd
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.11-rc6.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"VFS:
- Ensure that backing files uses file->f_ops->splice_write() for
splice
netfs:
- Revert the removal of PG_private_2 from netfs_release_folio() as
cephfs still relies on this
- When AS_RELEASE_ALWAYS is set on a mapping the folio needs to
always be invalidated during truncation
- Fix losing untruncated data in a folio by making letting
netfs_release_folio() return false if the folio is dirty
- Fix trimming of streaming-write folios in netfs_inval_folio()
- Reset iterator before retrying a short read
- Fix interaction of streaming writes with zero-point tracker
afs:
- During truncation afs currently calls truncate_setsize() which sets
i_size, expands the pagecache and truncates it. The first two
operations aren't needed because they will have already been done.
So call truncate_pagecache() instead and skip the redundant parts
overlayfs:
- Fix checking of the number of allowed lower layers so 500 layers
can actually be used instead of just 499
- Add missing '\n' to pr_err() output
- Pass string to ovl_parse_layer() and thus allow it to be used for
Opt_lowerdir as well
pidfd:
- Revert blocking the creation of pidfds for kthread as apparently
userspace relies on this. Specifically, it breaks systemd during
shutdown
romfs:
- Fix romfs_read_folio() to use the correct offset with
folio_zero_tail()"
* tag 'vfs-6.11-rc6.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
netfs: Fix interaction of streaming writes with zero-point tracker
netfs: Fix missing iterator reset on retry of short read
netfs: Fix trimming of streaming-write folios in netfs_inval_folio()
netfs: Fix netfs_release_folio() to say no if folio dirty
afs: Fix post-setattr file edit to do truncation correctly
mm: Fix missing folio invalidation calls during truncation
ovl: ovl_parse_param_lowerdir: Add missed '\n' for pr_err
ovl: fix wrong lowerdir number check for parameter Opt_lowerdir
ovl: pass string to ovl_parse_layer()
backing-file: convert to using fops->splice_write
Revert "pidfd: prevent creation of pidfds for kthreads"
romfs: fix romfs_read_folio()
netfs, ceph: Partially revert "netfs: Replace PG_fscache by setting folio->private and marking dirty"
Lunar Lake has been usable for a while in a desktop setup. Bugs are
sporadically showing up in CI, but being promptly fixed. Nothing very
concerning.
All the uapi changes related to fundamental platform usage have been
finalized.
Remove the force_probe requirement and enable the platform by default.
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822224615.793540-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The temperature reading function was using a signed long for the ADC
code, which could lead to mishandling of invalid codes on 32-bit
platforms. This allowed out-of-range ADC codes to be incorrectly
interpreted as valid values and used in temperature calculations.
Change adc_code to u32 to ensure that invalid ADC codes are correctly
identified on all platforms.
Fixes: 1b2ca93cd0 ("hwmon: Add driver for Astera Labs PT5161L retimer")
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Message-ID: <20240819104630.2375441-1-chou.cosmo@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
