Add pinctrl nodes for the r_i2c node. Without the pinmux defined the
r_i2c bus may fail to work, possibly if the bootloader uses rsb mode
for the PMIC.
Fixes: 0d17c86511 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Fixes: 0d17c86511 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Link: https://lore.kernel.org/r/20240710231718.106894-3-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the Anbernic RG35XXSP variant device.
The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
clamshell form-factor with an external RTC and a lid switch.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240710231718.106894-2-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Compile-testing the crypto/caam driver on alpha showed a pre-existing
problem on alpha with iowrite64be() missing:
ERROR: modpost: "iowrite64be" [drivers/crypto/caam/caam_jr.ko] undefined!
The prototypes were added a while ago when we started using asm-generic/io.h,
but the implementation was still missing. At some point the ioread64/iowrite64
helpers were added, but the big-endian versions are still missing, and
the generic version (using readq/writeq) is would not work here.
Change it to wrap ioread64()/iowrite64() instead.
Fixes: beba3771d9 ("crypto: caam: Make CRYPTO_DEV_FSL_CAAM dependent of COMPILE_TEST")
Fixes: e19d4ebc53 ("alpha: add full ioread64/iowrite64 implementation")
Fixes: 7e772dad99 ("alpha: Use generic <asm-generic/io.h>")
Closes: https://lore.kernel.org/all/CAHk-=wgEyzSxTs467NDOVfBSzWvUS6ztcwhiy=M3xog==KBmTw@mail.gmail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the PWM function using the platform device
registered by the core MFD driver.
The driver is derived from an initial implementation from NXP, available
in commit 113113742208 ("MLK-25922-1 pwm: adp5585: add adp5585 PWM
support") in their BSP kernel tree. It has been extensively rewritten.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Link: https://lore.kernel.org/r/20240722121100.2855-5-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the GPIO function using the platform device
registered by the core MFD driver.
The driver is derived from an initial implementation from NXP, available
in commit 451f61b46b76 ("MLK-25917-2 gpio: adp5585-gpio: add
adp5585-gpio support") in their BSP kernel tree. It has been extensively
rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-4-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the chip by modelling it as an MFD device, with two
child devices for the GPIO and PWM functions.
The driver is derived from an initial implementation from NXP, available
in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core
support") in their BSP kernel tree. It has been extensively rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
These bindings model the device as an MFD, and support the GPIO expander
and PWM functions.
These bindings support the GPIO and PWM functions.
Drop the existing adi,adp5585 and adi,adp5585-02 compatible strings from
trivial-devices.yaml. They have been added there by mistake as the
driver that was submitted at the same time used different compatible
strings. We can take them over safely.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240722121100.2855-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
While x86_64 has PMD aligned text sections, i386 does not have this
luxery. Notably ALIGN_ENTRY_TEXT_END is empty and _etext has PAGE
alignment.
This means that text on i386 can be page granular at the tail end,
which in turn means that the PTI text clones should consistently
account for this.
Make pti_clone_entry_text() consistent with pti_clone_kernel_text().
Fixes: 16a3fe634f ("x86/mm/pti: Clone kernel-image on PTE level for 32 bit")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Guenter reported dodgy crashes on an i386-nosmp build using GCC-11
that had the form of endless traps until entry stack exhaust and then
#DF from the stack guard.
It turned out that pti_clone_pgtable() had alignment assumptions on
the start address, notably it hard assumes start is PMD aligned. This
is true on x86_64, but very much not true on i386.
These assumptions can cause the end condition to malfunction, leading
to a 'short' clone. Guess what happens when the user mapping has a
short copy of the entry text?
Use the correct increment form for addr to avoid alignment
assumptions.
Fixes: 16a3fe634f ("x86/mm/pti: Clone kernel-image on PTE level for 32 bit")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20240731163105.GG33588@noisy.programming.kicks-ass.net
Add check for the return value of spi_setup() and return the error
if it fails in order to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240705092800.3221159-1-nichen@iscas.ac.cn
Signed-off-by: Lee Jones <lee@kernel.org>
The flash module has status bits to indicate different thermal
conditions which are called as OTSTx. For each OTSTx status,
there is a recommended total flash current for all channels to
prevent the flash module entering into higher thermal level.
For example, the total flash current should be limited to 1000mA/500mA
respectively when the HW reaches the OTST1/OTST2 thermal level.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Link: https://lore.kernel.org/r/20240705-qcom_flash_thermal_derating-v3-1-8e2e2783e3a6@quicinc.com
Signed-off-by: Lee Jones <lee@kernel.org>
The iterated nodes are direct children of the device node, and the
`device_for_each_child_node()` macro accounts for child node
availability.
`fwnode_for_each_available_child_node()` is meant to access the child
nodes of an fwnode, and therefore not direct child nodes of the device
node.
In this case, the child nodes are not required outside the loop, and
the scoped version of the macro can be used to remove the repetitive
`goto put` pattern.
Use `device_for_each_child_node_scoped_scoped()` to indicate device's
direct child nodes.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240721-device_for_each_child_node-available-v2-4-f33748fd8b2d@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The current implementation accesses the `child` fwnode handle outside of
fwnode_for_each_available_child_node() without incrementing its
refcount. Add the missing call to `fwnode_handle_get(child)`.
The cleanup process where `child` is accessed is not right either
because a single call to `fwnode_handle_put()` is carried out in case of
an error, ignoring unasigned nodes at the point when the error happens.
Keep `child` inside of the first loop, and use the helper pointer that
receives references via `fwnode_handle_get()` to handle the child nodes
within the second loop.
Moreover, the iterated nodes are direct children of the device node,
and the `device_for_each_child_node()` macro accounts for child node
availability. By restricting `child` to live within that loop, the
scoped version of it can be used to simplify the error handling.
`fwnode_for_each_available_child_node()` is meant to access the child
nodes of an fwnode, and therefore not direct child nodes of the device
node.
Use `device_for_each_child_node_scoped()` to indicate device's direct
child nodes.
Fixes: 8325642d27 ("leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240721-device_for_each_child_node-available-v2-3-f33748fd8b2d@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Convert the Spreadtrum SC2731 breathing light controller bindings
to DT schema. Adjust filename to match compatible.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/ZpKM3yYKJixnRabP@standask-GA-A55M-S2HP
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for PCA9956B chip, which belongs to the same family.
This chip features 24 instead of 16 outputs, so add a chipdef struct to
deal with the different register layouts.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pieterjan Camerlynck <pieterjanca@gmail.com>
Link: https://lore.kernel.org/r/20240711-pca995x-v4-2-702a67148065@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add nxp,pca9956b compatible, which has 24 instead of 16 outputs. Adjust
the documentation for the difference.
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Pieterjan Camerlynck <pieterjanca@gmail.com>
Link: https://lore.kernel.org/r/20240711-pca995x-v4-1-702a67148065@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add multicolor support to the BlinkM driver, making it easier to control
from userspace. The BlinkM LED is a programmable RGB LED. The driver
currently supports only the regular LED sysfs class, resulting in the
creation of three distinct classes, one for red, green, and blue. The
user then has to input three values into the three seperate brightness
files within those classes. The multicolor LED framework makes the
device easier to control with the multi_intensity file: the user can
input three values at once to form a color, while still controlling the
lightness with the brightness file.
The main struct blinkm_led has changed slightly. The struct led_classdev
for the regular sysfs classes remain. The blinkm_probe function checks
CONFIG_LEDS_BLINKM_MULTICOLOR to decide whether to load the seperate
sysfs classes or the single multicolor one, but never both. The
blinkm_set_mc_brightness() function had to be added to calculate the
three color components and then set the fields of the blinkm_data
structure accordingly.
Signed-off-by: Joseph Strauss <jstrauss@mailbox.org>
Link: https://lore.kernel.org/r/20240710184844.108006-1-jstrauss@mailbox.org
Signed-off-by: Lee Jones <lee@kernel.org>
This patch provides support for enabling blinking of LEDs when RX or TX
errors are detected.
Approach taken in this patch is similar to one for TX or RX data
transmission indication (i.e. TRIGGER_NETDEV_TX/RX attribute).
One can inspect transmission errors with:
ip -s link show eth0
Example LED configuration:
cd /sys/devices/platform/amba_pl@0/a001a000.leds/leds/
echo netdev > mode:blue/trigger && \
echo eth0 > mode:blue/device_name && \
echo 1 > mode:blue/tx_err
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240710100651.4059887-1-lukma@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
The torch_current_max should be checked not exceeding the upper bound.
If it does, throw a warning message and set to LM3601X_MAX_TORCH_I_UA.
LM3601x torch brigthness register (LM3601X_LED_TORCH_REG) takes 0 as the
minimum output (2.4 mA). However, 0 of led_brightness means LED_OFF.
Adding a -1 offset to brightness before writing to brightness
register, so when users write minimum brightness (1), it sets lm3601x
output the minimum.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20240704191500.766846-1-zenghuchen@google.com
Signed-off-by: Lee Jones <lee@kernel.org>
AMD Zen-based systems report memory error addresses through machine
check banks representing Unified Memory Controllers (UMCs) in the form
of UMC relative "normalized" addresses. A normalized address must be
converted to a system physical address to be usable by the OS.
Future AMD platforms will provide a UEFI PRM module that implements a
number of address translation PRM handlers. This will provide an
interface for the OS to call platform specific code without requiring
the use of SMM or other heavy firmware operations.
Add support for the normalized to system physical address translation
PRM handler in the AMD Address Translation Library and prefer it over
native code if available. The GUID and parameter buffer structure are
specific to the normalized to system physical address handler provided
by the address translation PRM module included in future AMD systems.
The address translation PRM module is documented in chapter 22 of the
publicly available "AMD Family 1Ah Models 00h–0Fh and Models 10h–1Fh
ACPI v6.5 Porting Guide".
[ bp: Massage commit message. ]
Signed-off-by: John Allen <john.allen@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240730151731.15363-3-john.allen@amd.com
Platform Runtime Mechanism (PRM) handlers can be invoked from either the AML
interpreter or directly by an OS driver. Implement the latter.
[ bp: Massage commit message. ]
Signed-off-by: John Allen <john.allen@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20240730151731.15363-2-john.allen@amd.com
Use of_property_read_bool() to read boolean properties rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240731191312.1710417-20-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240731191312.1710417-19-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace FB_BLANK_ constants with their counterparts from the
backlight subsystem. The values are identical, so there's no
change in functionality or semantics.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240731122311.1143153-3-tzimmermann@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use of_property_read_bool() to read boolean properties rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240731191312.1710417-24-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix sparse warning:
drivers/regulator/max77857-regulator.c:430:28: warning: symbol 'max77857_id' was not declared. Should it be static?
max77857_id is not used outside the source file. Make it static.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20240801114536.472796-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add pci_rev variable in acp sof driver private data structure and assign
this value to mach_params structure subsystem_rev variable.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-10-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Few IP's may have same PCI vendor id and device id and
different revision id. Add revision id field to the
'snd_soc_acpi_mach_params' so that using this field platform
specific implementation can be added in machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-7-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it generic, refactor existing implementation for
init_dai_link() and init_simple_dai_link() as mentioned below.
- Move init_dai_link() and init_simple_dai_link() to common place holder
- Rename the functions with "asoc_sdw" as prefix.
- Pass the platform specific 'platform_component' structure and its size as
arguments for init_simple_dai_link() function and allocate one more
extra dlc for platform component.
- Pass the 'platform_component' and 'num_platforms' as arguments for
init_dai_link().
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-6-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor sof_sdw_card_late_probe() function and derive a generic
function soc_sdw_card_late_probe() function which can be used by
SoundWire generic machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-5-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move machine driver dai link helper functions to common place holder,
So that it can be used by other platform machine driver.
Rename these functions with "asoc_sdw" tag as a prefix.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-4-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire 'codec_info_list' structure is not a platform specific one.
Move codec_info_list structure to common file soc_sdw_utils.c.
Move codec helper functions which uses codec_info_list structure to common
place holder and rename the function by adding _sdw tag. This will allow
to use 'codec_info_list' structure and it's helper functions in other
platform machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move SoundWire dai type macros to common header file(soc_sdw_util.h).
So that these macros will be used by other platform machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move dai id common macros from intel SoundWire generic driver to
soc_sdw_utils.h file so that it can be used by other platform machine
driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801111821.18076-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move maxim codec helper functions to common place holder so that
it can be used by other platform machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801091446.10457-21-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it generic, move Cirrus Soundwire codec helper functions to
common place holder so that it can be used by other platform machine
driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801091446.10457-20-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move RTK amp codec helper functions related implementation to common
place holder to make it generic so that these helper functions will be
used by other platform machine driver modules.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801091446.10457-19-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move RT700 and RT711 Soundwire codec helper functions to common
place holder so that it can be used by other platform machine driver.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801091446.10457-18-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move RTK codec jack common helper functions to common place holder
(sdw_utils folder) to make it generic so that it will be used by
other platform machine driver code.
Link: https://github.com/thesofproject/linux/pull/5068
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://patch.msgid.link/20240801091446.10457-17-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
