Driver stores the voltage of mic bias in fields in state container
structure, but actually never reads them - except for the mic2 bias
(micb2_mv field). Drop the fields from the structure so the code will
be a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-9-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver does not modify few static data (arrays with sample rates, MBHC
reg fields, regmap config), so make them const for code safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-8-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver was prepared to adjust DMIC microphone parameters according to
DMIC clock rate which is read from platform data or Devicetree. The
latter part never happened, so the code is always called with
dmic_clk_rate=0, prints error and uses default/fallback values. All
this part can be simplified by dropping dead parts of code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-6-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Error-level should not be used as debugging. The code (function
wcd9335_get_dmic_clk_val()) will always be called with same parameters,
so this is not really useful debug anyway, so drop it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-5-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
wcd9335_parse_dt() function is called only from probe(), so printing
errors on resource acquisition is discouraged, because it can pollute
dmesg. Use dev_err_probe() to fix this and also make the code a bit
simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-4-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver does not modify few static data (arrays with sample rates,
interrupt description, regmap config), so make them const for code
safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-3-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The wcd-mbhc-v2 helper code/module does not modify passed array of
registry fields, thus it can be made const for code safety. It will
also allow individual drivers to allocate the array in rodata.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240612-asoc-wcd9xxx-wide-cleanups-v1-1-0d15885b2a06@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In only loading RCA (Reconfigurable Architecture) binary case, no DSP
program will be working inside tas2563/tas2781, that is dsp-bypass mode,
do not support speaker protection, or audio acoustic algorithms in this
mode.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240614133646.910-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree property to define auxiliary devices to be added to
Audio Graph Card which is already supported on Simle Card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://msgid.link/r/87jzin3yc8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds MCLK clock handling directly within driver.
When used in combination with simple-audio-card, and mclk-fs is set,
simple-audio-card will change MCLK frequency before configuring PLL.
In some cases, however, MCLK reference clock should be static (see [1]),
which means it needs to be moved away from simple-audio-card.
[1]: https://lore.kernel.org/all/ZfBdxrzX3EnPuGOn@ediswmail9.ad.cirrus.com/
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Link: https://msgid.link/r/20240613084652.13113-4-andrejs.cainikovs@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following bias state machine logic this bit is set twice before playback.
This change makes sure this bit set is set only once.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Suggested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Link: https://msgid.link/r/20240613084652.13113-3-andrejs.cainikovs@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Next commit in series makes a change which calls nau8822_set_pll() from
nau8822_set_dai_sysclk(). Moving latter after the former would avoid a
forward declaration, and this is exactly what this change does.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Link: https://msgid.link/r/20240613084652.13113-2-andrejs.cainikovs@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After catching up with KP recently, we discussed that I will be now be
responsible for co-maintaining the BPF LSM. Adding myself as
designated maintainer of the BPF LSM, and specifying more files in
which the BPF LSM maintenance responsibilities should now extend out
to. This is at the back of all the BPF kfuncs that have been added
recently, which are fundamentally restricted to being used only from
BPF LSM program types.
Signed-off-by: Matt Bobrowski <mattbobrowski@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/ZnA-1qdtXS1TayD7@google.com
With ARCH=arm64, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pci/hotplug/acpiphp_ampere_altra.o
Add the missing MODULE_DESCRIPTION().
Link: https://lore.kernel.org/r/20240612-md-drivers-pci-hotplug-v1-1-2b30d14d783d@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After commit 35fe6d7632 ("block: use standard blktrace API to output
cgroup info for debug notes"), the field 'bfqg->blkg_path' is not used
and hence can be removed, and therefor blkg_path() is not used anymore
and can be removed.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240618032753.3502528-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The race condition between fbcon and drm_panic can only occurs if
VT_CONSOLE is set. So update drm_panic dependency accordingly.
This will make it easier for Linux distributions to enable drm_panic
by disabling VT_CONSOLE, and keeping fbcon terminal.
The only drawback is that fbcon won't display the boot kmsg, so it
should rely on userspace to do that.
At least plymouth already handle this case with
https://gitlab.freedesktop.org/plymouth/plymouth/-/merge_requests/224
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613154041.325964-1-jfalempe@redhat.com
TMP108 is powered by its V+ supply, document it. The property is called
"vcc-supply" since the plus sign (+) is not an expected character.
While at it, add a short description with a link to its datasheets.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/ZnBmDXfnDQXNXz3k@standask-GA-A55M-S2HP
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assign the output from get_lowcore() to a local variable,
so the code is easier to read.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Assign the output from get_lowcore() to a local variable,
so the code is easier to read.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Assign the output from get_lowcore() to a local variable,
so the code is easier to read.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Assign the output from get_lowcore() to a local variable,
so the code is easier to read.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Assign the output from get_lowcore() to a local variable,
so the code is easier to read.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Replace all S390_lowcore usages in arch/s390/boot by get_lowcore().
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Replace all S390_lowcore usages in drivers/s390 by get_lowcore().
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Replace all S390_lowcore usages in arch/s390/ by get_lowcore().
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add a get_lowcore() function which returns the address
of lowcore (currently always NULL). This function will
be used as a replacement of the S390_lowcore macro.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Ensure that EFI runtime services are not unmapped by PAN on ARM
- Avoid freeing the memory holding the EFI memory map inadvertently on
x86
- Avoid a false positive kmemleak warning on arm64
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQQm/3uucuRGn1Dmh0wbglWLn0tXAUCZm1QFgAKCRAwbglWLn0t
XDCpAP9tB6S9uQwDsR9PuxJfWOALJEqoMWCjGzLjt5HlGePlvAD9HaltvkT5p9Ff
TkfP4Ivl29BtuaNBIFGEiC6KJXETawc=
=Tvsr
-----END PGP SIGNATURE-----
Merge tag 'efi-fixes-for-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"Another small set of EFI fixes. Only the x86 one is likely to affect
any actual users (and has a cc:stable), but the issue it fixes was
only observed in an unusual context (kexec in a confidential VM).
- Ensure that EFI runtime services are not unmapped by PAN on ARM
- Avoid freeing the memory holding the EFI memory map inadvertently
on x86
- Avoid a false positive kmemleak warning on arm64"
* tag 'efi-fixes-for-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/arm64: Fix kmemleak false positive in arm64_efi_rt_init()
efi/x86: Free EFI memory map only when installing a new one.
efi/arm: Disable LPAE PAN when calling EFI runtime services
It is possible that during system boot when there multiple devices
attempting simultaneous initialization on a slow control bus the
download of firmware and tuning data may take a user perceivable amount
of time (a slow I2C bus with 4 amps this work could take over 2
seconds).
Adopt a pattern used in the ASoC driver and perform this activity in a
background thread so that interactive performance is not impaired. The
system_long_wq is a parallel workqueue and driver instances will perform
their firmware downloads in parallel to make best use of available bus
bandwidth.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://lore.kernel.org/20240618130011.62860-1-simont@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a file is opened and created with open(..., O_CREAT) we get
both the CREATE and OPEN fsnotify events and would expect them in that
order. For most filesystems we get them in that order because
open_last_lookups() calls fsnofify_create() and then do_open() (from
path_openat()) calls vfs_open()->do_dentry_open() which calls
fsnotify_open().
However when ->atomic_open is used, the
do_dentry_open() -> fsnotify_open()
call happens from finish_open() which is called from the ->atomic_open
handler in lookup_open() which is called *before* open_last_lookups()
calls fsnotify_create. So we get the "open" notification before
"create" - which is backwards. ltp testcase inotify02 tests this and
reports the inconsistency.
This patch lifts the fsnotify_open() call out of do_dentry_open() and
places it higher up the call stack. There are three callers of
do_dentry_open().
For vfs_open() and kernel_file_open() the fsnotify_open() is placed
directly in that caller so there should be no behavioural change.
For finish_open() there are two cases:
- finish_open is used in ->atomic_open handlers. For these we add a
call to fsnotify_open() at open_last_lookups() if FMODE_OPENED is
set - which means do_dentry_open() has been called.
- finish_open is used in ->tmpfile() handlers. For these a similar
call to fsnotify_open() is added to vfs_tmpfile()
With this patch NFSv3 is restored to its previous behaviour (before
->atomic_open support was added) of generating CREATE notifications
before OPEN, and NFSv4 now has that same correct ordering that is has
not had before. I haven't tested other filesystems.
Fixes: 7c6c5249f0 ("NFS: add atomic_open for NFSv3 to handle O_TRUNC correctly.")
Reported-by: James Clark <james.clark@arm.com>
Closes: https://lore.kernel.org/all/01c3bf2e-eb1f-4b7f-a54f-d2a05dd3d8c8@arm.com
Signed-off-by: NeilBrown <neilb@suse.de>
Link: https://lore.kernel.org/r/171817619547.14261.975798725161704336@noble.neil.brown.name
Fixes: 7b8c9d7bb4 ("fsnotify: move fsnotify_open() hook into do_dentry_open()")
Tested-by: James Clark <james.clark@arm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240617162303.1596-2-jack@suse.cz
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Currently we will not generate FS_OPEN events for O_PATH file
descriptors but we will generate FS_CLOSE events for them. This is
asymmetry is confusing. Arguably no fsnotify events should be generated
for O_PATH file descriptors as they cannot be used to access or modify
file content, they are just convenient handles to file objects like
paths. So fix the asymmetry by stopping to generate FS_CLOSE for O_PATH
file descriptors.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240617162303.1596-1-jack@suse.cz
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The block device may have been frozen before it was claimed by a
filesystem. Concurrently another process might try to mount that
frozen block device and has temporarily claimed the block device for
that purpose causing a concurrent fs_bdev_thaw() to end up here. The
mounter is already about to abort mounting because they still saw an
elevanted bdev->bd_fsfreeze_count so get_bdev_super() will return
NULL in that case.
For example, P1 calls dm_suspend() which calls into bdev_freeze() before
the block device has been claimed by the filesystem. This brings
bdev->bd_fsfreeze_count to 1 and no call into fs_bdev_freeze() is
required.
Now P2 tries to mount that frozen block device. It claims it and checks
bdev->bd_fsfreeze_count. As it's elevated it aborts mounting.
In the meantime P3 called dm_resume(). P3 sees that the block device is
already claimed by a filesystem and calls into fs_bdev_thaw().
P3 takes a passive reference and realizes that the filesystem isn't
ready yet. P3 puts itself to sleep to wait for the filesystem to become
ready.
P2 now puts the last active reference to the filesystem and marks it as
dying. P3 gets woken, sees that the filesystem is dying and
get_bdev_super() fails.
Fixes: 49ef8832fb ("bdev: implement freeze and thaw holder operations")
Cc: <stable@vger.kernel.org>
Reported-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20240611085210.GA1838544@mit.edu
Link: https://lore.kernel.org/r/20240613-lackmantel-einsehen-90f0d727358d@brauner
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Now that the driver core can properly handle constant struct bus_type,
move the parport_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-parport-v1-1-e6a0f756bbb8@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case usage of OCTAL mode, buswidth parameter can take the value 8.
As return value of stm32_qspi_get_mode() is used to configure fields
of CCR registers that are 2 bits only (fields IMODE, ADMODE, ADSIZE,
DMODE), clamp return value of stm32_qspi_get_mode() to 4.
Fixes: a557fca630 ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Misplaced parenthesis make test of mode wrong in case mode is equal to
SPI_TX_OCTAL or SPI_RX_OCTAL.
Simplify this sanity test, if one of this bit is set, property
cs-gpio must be present in DT.
Fixes: a557fca630 ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"struct vcap_operations" are not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increase overall security.
In order to do it, "struct vcap_control" also needs to be adjusted to this
new const qualifier.
As an example, on a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
15176 1094 16 16286 3f9e drivers/net/ethernet/microchip/lan966x/lan966x_vcap_impl.o
After:
=====
text data bss dec hex filename
15268 998 16 16282 3f9a drivers/net/ethernet/microchip/lan966x/lan966x_vcap_impl.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/d8e76094d2e98ebb5bfc8205799b3a9db0b46220.1718524644.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
zones_ht is a global hashtable for flow_table with zone as key. However,
it does not consider netns when getting a flow_table from zones_ht in
tcf_ct_init(), and it means an act_ct action in netns A may get a
flow_table that belongs to netns B if it has the same zone value.
In Shuang's test with the TOPO:
tcf2_c <---> tcf2_sw1 <---> tcf2_sw2 <---> tcf2_s
tcf2_sw1 and tcf2_sw2 saw the same flow and used the same flow table,
which caused their ct entries entering unexpected states and the
TCP connection not able to end normally.
This patch fixes the issue simply by adding netns into the key of
tcf_ct_flow_table so that an act_ct action gets a flow_table that
belongs to its own netns in tcf_ct_init().
Note that for easy coding we don't use tcf_ct_flow_table.nf_ft.net,
as the ct_ft is initialized after inserting it to the hashtable in
tcf_ct_flow_table_get() and also it requires to implement several
functions in rhashtable_params including hashfn, obj_hashfn and
obj_cmpfn.
Fixes: 64ff70b80f ("net/sched: act_ct: Offload established connections to flow table")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1db5b6cc6902c5fc6f8c6cbd85494a2008087be5.1718488050.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add boolean ti,micbias1-gpo and ti,micbias2-gpo devicetree properties.
When set, the respective MICBIAS pins can be used as general purpose
outputs controlled via the GPIO framework, in addition to the two
configurable GPIO pins.
This is useful in applications where the MICBIAS functionality is
not required, but it is useful to have a couple of extra GPIO pins.
The voltage on the respective MICBIAS pin in the active state is
governed by the ti,micbias1-vg and ti,micbias2-vg properties,
respectively (same properties as when the pins are used as
MICBIAS pins).
Signed-off-by: Ricard Wanderlof <ricard.wanderlof@axis.com>
Link: https://msgid.link/r/20240607-tlv320adc3xxx-micbias-gpo-v3-2-59dbec8b98f4@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add properties for configuring the MICBIAS pins as general purpose
outputs, with some limitations: The voltage on the pin when activated
may be set using another property to 2.0 V, 2.5 V or AVDD.
When deactivated the pin will float.
Signed-off-by: Ricard Wanderlof <ricard.wanderlof@axis.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240607-tlv320adc3xxx-micbias-gpo-v3-1-59dbec8b98f4@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for handling jack events of USB (DisplayPort).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # X13s
Link: https://msgid.link/r/20240606104922.114229-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Display Port Jack events.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # X13s
Link: https://msgid.link/r/20240606104922.114229-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a common function to add Display port jack.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # X13s
Link: https://msgid.link/r/20240606104922.114229-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Returned 'struct snd_soc_pcm_stream' by snd_soc_dai_get_pcm_stream() is
not modified by the users, so it can be changed as pointer to const.
This is a necessary step towards making the 'dai->driver' a pointer to
const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240617-n-asoc-const-auto-selectable-formats-v1-5-8004f346ee38@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
get_channel_map() is supposed to obtain map of channels without
modifying the state of the given DAI, so make the pointer to 'struct
snd_soc_dai' as pointing to const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240617-n-asoc-const-auto-selectable-formats-v1-4-8004f346ee38@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
