Add connector debugfs entries to force the link rate/lane count to be
used by a link training afterwards. These settings will be clamped to
the supported, i.e. the source's and sink's common rate/lane count.
After forcing the link rate/lane count reset the link training
parameters and for a non-auto setting disable reducing the link
parameters via the fallback logic. The former one can be used after
testing link training failure scenarios - via debugfs entries added
later - to reset the reduced link parameters after the test.
v2:
- Add the entries from intel_dp_link_training.c (Jani)
- Rename the entries to i915_dp_set_link_rate/lane_count.
v3: (Ville)
- Rename the entries/struct fields to force_link_rate/lane_count.
- Lock connection_mutex only for the required intel_dp state.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-18-imre.deak@intel.com
Reduce the link parameters after a link training failure for MST
outputs, similarly to how this is done for SST.
For now allow the reduction only by staying in the 8b/10b vs. 128b/132b
mode. Enabling the mode switch is left for a follow-up patchset, after
taking measures ensuring that the mode switch happens properly. In
particular a rediscovery of the whole MST topology may be required for
such a switch, see the References below.
Link: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/10970
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-17-imre.deak@intel.com
Reset the flag indicating an active link after disabling an MST link,
similarly to how this is done for SST outputs. This avoids trying to
retrain an MST link while its disabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-16-imre.deak@intel.com
After a link training failure if the link parameters can't be further
reduced, there is no point in trying to retrain the link in the driver.
This avoids excessive retrain attempts after detecting a bad link, for
instance while handling MST HPD IRQs, which is likely redundant as the
link training failed already twice with the same minimum link
parameters. Userspace can still try to retrain the link with these
parameters via a modeset.
While at it make the error message more accurate.
v2: Move converting the error to a debug message to the relevant
follow-up patch. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-15-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
HPD IRQ handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-14-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
connector detect handler from the encoder's check link state work,
similarly to how this is done after a modeset link training failure.
v2: Add TODO: comment to remove the detect-time link state check.
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-13-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
hotplug handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-12-imre.deak@intel.com
Send a modeset-retry uevent to all connectors in the same MST topology
after a link training failure and reduction of the link parameters. This
matches the way the same uevent is sent after a DP tunnel BW allocation
failure.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-11-imre.deak@intel.com
The next patch adds sending a modeset-retry uevent after a link training
failure to all MST connectors on link. This requires the atomic state,
so pass it to intel_dp_start_link_train(). In case of SST where
retraining still happens by calling this function directly instead of a
modeset commit the atomic state is not available and NULL is passed
instead. This is ok, since in this case the encoder's only DP connector
is available from intel_dp->attached_connector not requiring the atomic
state.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-10-imre.deak@intel.com
Try to maintain the current link parameters by retrying the link
training with unchanged link parameters before reducing these parameters
(sending an uevent to userspace to retrain the link instead).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-9-imre.deak@intel.com
Recheck the link state after a passing link training, with a 2 sec delay
to account for cases where the link goes bad following the link training
and the sink doesn't report this via an HPD IRQ.
The delayed work added here will be also used by a later patch after a
failed link training to try to retrain the link with unchanged link
params before reducing the link params.
v2: Don't flush an uninitialized delayed work (on HDMI-only DDI ports).
v3:
- Move the helpers to a new intel_encoder.c file, rename them
accordingly. (Ville)
- Add the work to intel_encoder instead of intel_digital_port.
- Call the encoder specific link check function via an encoder hook.
- Flush the link check work during encoder destroy from
intel_dp_encoder_flush_work().
- Flush the link check work during encoder suspend as well.
v4: Call intel_encoder_link_check_init() with a valid encoder pointer.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610181428.2955658-1-imre.deak@intel.com
Instead of direct calls to the link train functions, retrain the link
via a commit modeset. The direct call means that the output port will be
disabled/re-enabled while the rest of the pipeline (transcoder) is
active, which doesn't seem to work on MST at least. It leads to
underruns and black screen, presumedly because the transcoder is not
disabled/re-enabled along the port.
Leave switching to a commit modeset on SST for a later patchset, as that
seems to work ok currently (though better to using a commit there too,
due to the suppressed underruns).
v2: Keep reverse line length order for local variables. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-7-imre.deak@intel.com
Reduce the indentation in intel_dp_get_link_train_fallback_values() by
adding separate helpers to reduce the link rate and lane count. Also
simplify things by passing crtc_state to the function.
This also prepares for later patches in the patchset adding a limitation
on how the link params are reduced.
While at it use lt_dbg()/lt_err() for debug/error prints in the function
which will also print the connector/encoder prefix and add a debug print
about reducing the link parameters.
v2:
- Align reduce_lane_count()'s error handling flow with
reduce_link_rate(). (Ville, Jani)
- Use lt_dbg()/lt_err() in the function.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-5-imre.deak@intel.com
Move the functions used to reduce the link parameters during link
training to intel_dp_link_training.c .
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-4-imre.deak@intel.com
pcpu_hot (defined in arch/x86) is not available on user mode linux (ARCH=um)
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Fixes: 1ae6921009 ("bpf: inline bpf_get_smp_processor_id() helper")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240613173146.2524647-1-maze@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add ODRs accessible only in low-power mode. Switch automatically to
low-power or low-noise depending on the ODR set.
Add channel attributes "power_mode" and "power_mode_available" for
setting the power mode to use (low-noise or low-power) for ODRs
supporting both mode. Reading "power_mode" when the sensor is on
will return the actual mode and not the requested one. It will be
different when using ODRs not supported by the requested mode.
Use low-power mode by default.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240605195949.766677-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ENS160 supports a deep sleep mode for minimal power consumption.
Use it to add PM sleep capability to the driver.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Link: https://lore.kernel.org/r/20240604225747.7212-6-gustavograzs@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ENS160 supports a data ready interrupt. Use it in combination with
triggered buffer for continuous data readings.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Link: https://lore.kernel.org/r/20240604225747.7212-5-gustavograzs@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device has four programmable temperature alert outputs which can be
used to monitor hot or cold-junction temperatures and detect falling and
rising temperatures. It supports up to 255 degree celsius programmable
hysteresis. Each alert can be individually configured by setting following
options in the associated alert configuration register:
- monitor hot or cold junction temperature
- monitor rising or falling temperature
- set comparator or interrupt mode
- set output polarity
- enable alert
This patch binds alert outputs to iio events:
- alert1: hot junction, rising temperature
- alert2: hot junction, falling temperature
- alert3: cold junction, rising temperature
- alert4: cold junction, falling temperature
All outputs are set in comparator mode and polarity depends on interrupt
configuration.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240604133639.959682-1-dima.fedrau@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device tree bindings for the vishay VEML6040 RGBW light sensor iio
driver
Signed-off-by: Arthur Becker <arthur.becker@sentec.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240604-veml6040-v4-2-5a4d59597874@sentec.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Implements driver for the Vishay VEML6040 rgbw light sensor.
Included functionality: setting the integration time and reading the raw
values for the four channels
Not yet implemented: setting the measurements to 'Manual Force Mode' (Auto
measurements off, and adding a measurement trigger)
Datasheet: https://www.vishay.com/docs/84276/veml6040.pdf
Signed-off-by: Arthur Becker <arthur.becker@sentec.com>
Link: https://lore.kernel.org/r/20240604-veml6040-v4-1-5a4d59597874@sentec.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Being this device a soft core, it's only supported on some/specific
platforms. Hence add proper dependencies for the supported platforms.
Also add COMPILE_TEST to increase the build coverage.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240604-dev-axi-dac-kconfig-v1-1-99ccd03938d1@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Being this device a soft core, it's only supported on some/specific
platforms. Hence add proper dependencies for the supported platforms.
Also add COMPILE_TEST to increase the build coverage.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240604-dev-axi-adc-kconfig-v1-1-cfb725606b8e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Register caching is improving bus access a lot because of the register
window bank setting. Previously, bank register was set for every
register access. Now with caching, it happens only when changing bank
which is very infrequent.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240607081039.789079-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver calls spi_get_device_match_data() and on its failure calls
again parts of it: spi_get_device_id() and getting driver data. This is
entirely redundant, because it is part of spi_get_device_match_data().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-8-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-7-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-6-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-5-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-4-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-3-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-2-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606-spi-match-data-v1-1-320b291ee1fe@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240606155407.499344-1-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for the integrated on-chip heater that is present
on all the devices supported by this driver (si7020, si7021, si7013, th6).
In order to configure the heater, the driver interacts with the following
device registers:
* User Register - the 2nd bit of this register is a "Heater Enable bit"
(0 means that the heater is off, 1 means that it's on).
* Heater Register - this register is present only on the si70xx devices
and controls the current flowing through the heater. The 4 lower bits
of this register can be assigned values from 0x0 to 0xF.
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Link: https://lore.kernel.org/r/20240607141029.51744-1-apokusinski@o2.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/adc/ingenic-adc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/adc/xilinx-ams.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/buffer/kfifo_buf.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-iic-v1-1-9f9db6246083@quicinc.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). At the same time refactor
the NULL comparison.
This patch has no effect on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Link: https://lore.kernel.org/r/AS8PR02MB7237D024459C314CECE72EAF8BFE2@AS8PR02MB7237.eurprd02.prod.outlook.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AXP192 is identical to the AXP20x, except for the addition of
two more GPIO ADC channels.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
TI tla2021 is a limited single-channel variant of tla2024 which is
similar enough to be easily supportable through the same driver.
Add compatible string for tla2021 so boards may describe it in
device-tree.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240602-cn9130-som-v6-3-89393e86d4c7@solid-run.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of iio_device_claim_direct_scoped() to make error handling more
natural and simplify code.
Co-developed-by: Caio Dantas Simão Ugêda <caiodantas@usp.br>
Signed-off-by: Caio Dantas Simão Ugêda <caiodantas@usp.br>
Signed-off-by: Gustavo Ueti Fukunaga <gustavofukunaga@usp.br>
Link: https://lore.kernel.org/r/20240527091942.53616-1-gustavofukunaga@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow using the mount-matrix device tree property to align the
accelerometer relative to the whole device.
Signed-off-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/20240527080043.2709-1-val@packett.cool
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some callbacks from iio_info structure are accessed without any check, so
if a driver doesn't implement them trying to access the corresponding
sysfs entries produce a kernel oops such as:
[ 2203.527791] Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute
[...]
[ 2203.783416] Call trace:
[ 2203.783429] iio_read_channel_info_avail from dev_attr_show+0x18/0x48
[ 2203.789807] dev_attr_show from sysfs_kf_seq_show+0x90/0x120
[ 2203.794181] sysfs_kf_seq_show from seq_read_iter+0xd0/0x4e4
[ 2203.798555] seq_read_iter from vfs_read+0x238/0x2a0
[ 2203.802236] vfs_read from ksys_read+0xa4/0xd4
[ 2203.805385] ksys_read from ret_fast_syscall+0x0/0x54
[ 2203.809135] Exception stack(0xe0badfa8 to 0xe0badff0)
[ 2203.812880] dfa0: 00000003 b6f10f80 00000003 b6eab000 00020000 00000000
[ 2203.819746] dfc0: 00000003 b6f10f80 7ff00000 00000003 00000003 00000000 00020000 00000000
[ 2203.826619] dfe0: b6e1bc88 bed80958 b6e1bc94 b6e1bcb0
[ 2203.830363] Code: bad PC value
[ 2203.832695] ---[ end trace 0000000000000000 ]---
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://lore.kernel.org/r/20240530-iio-core-fix-segfault-v3-1-8b7cd2a03773@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Daniel Xu says:
====================
Fixes for kfunc prototype generation
This patchset fixes new warnings and errors that kfunc prototype
generation caused.
====================
Link: https://lore.kernel.org/r/cover.1718295425.git.dxu@dxuuu.xyz
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When selftests are built with a new enough clang, the arena selftests
opt-in to use LLVM address_space attribute annotations for arena
pointers.
These annotations are not emitted by kfunc prototype generation. This
causes compilation errors when clang sees conflicting prototypes.
Fix by opting arena selftests out of using generated kfunc prototypes.
Fixes: 770abbb5a2 ("bpftool: Support dumping kfunc prototypes from BTF")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202406131810.c1B8hTm8-lkp@intel.com/
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Link: https://lore.kernel.org/r/fc59a617439ceea9ad8dfbb4786843c2169496ae.1718295425.git.dxu@dxuuu.xyz
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
