Multicast routing is today handled in the input path. Locally generated MC
packets don't hit the IPMR code today. Thus if a VXLAN remote address is
multicast, the driver needs to set an OIF during route lookup. Thus MC
routing configuration needs to be kept in sync with the VXLAN FDB and MDB.
Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patch adds support to route locally generated multicast
packets. The newly-added routines do largely what ip_mr_input() and
ip_mr_forward() do: make an MR cache lookup to find where to send the
packets, and use ip_mc_output() to send each of them. When no cache entry
is found, the packet is punted to the daemon for resolution.
However, an installation that uses a VXLAN underlay netdevice for which it
also has matching MC routes, would get a different routing with this patch.
Previously, the MC packets would be delivered directly to the underlay
port, whereas now they would be MC-routed. In order to avoid this change in
behavior, introduce an IPCB flag. Only if the flag is set will
ip_mr_output() actually engage, otherwise it reverts to ip_mc_output().
This code is based on work by Roopa Prabhu and Nikolay Aleksandrov.
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/0aadbd49330471c0f758d54afb05eb3b6e3a6b65.1750113335.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some of the work of ipmr_queue_xmit() is specific to IPMR forwarding, and
should not take place on the output path. In order to allow reuse of the
common parts, split the function into two: the ipmr_prepare_xmit() helper
that takes care of the common bits, and the ipmr_queue_fwd_xmit(), which
invokes the former and encapsulates the whole forwarding algorithm.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/4e8db165572a4f8bd29a723a801e854e9d20df4d.1750113335.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable is used for caching of rt->dst.dev. The netdevice referenced
therein does not change during the scope of validity of that local. At the
same time, the local is only used twice, and each of these uses will end up
in a different function in the following patches, further eliminating any
use the local could have had.
Drop the local altogether and inline the uses.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/c80600a4b51679fe78f429ccb6d60892c2f9e4de.1750113335.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
iptunnel_xmit() erases the contents of the SKB control block. In order to
be able to set particular IPCB flags on the SKB, add a corresponding
parameter, and propagate it to udp_tunnel_xmit_skb() as well.
In one of the following patches, VXLAN driver will use this facility to
mark packets as subject to IP multicast routing.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Antonio Quartulli <antonio@openvpn.net>
Link: https://patch.msgid.link/89c9daf9f2dc088b6b92ccebcc929f51742de91f.1750113335.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The underlying lookup_user_key() function uses a signed 32 bit integer
for key serial numbers because legitimate serial numbers are positive
(and > 3) and keyrings are negative. Using a u32 for the keyring in
the bpf function doesn't currently cause any conversion problems but
will start to trip the signed to unsigned conversion warnings when the
kernel enables them, so convert the argument to signed (and update the
tests accordingly) before it acquires more users.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Link: https://lore.kernel.org/r/84cdb0775254d297d75e21f577089f64abdfbd28.camel@HansenPartnership.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bcmp() was removed in POSIX.1-2008.
This commit replaces bcmp() with memcmp(). This allows Kconfig to link
with C libraries that do not provide bcmp(), such as Android bionic
libc.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reported-by: Abhigyan Ghosh <zscript.team.zs@gmail.com>
[masahiro: update commit description]
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Gal Pressman says:
====================
Misc vlan cleanups
This patch series addresses compilation issues with objtool when VLAN
support is disabled (CONFIG_VLAN_8021Q=n) and makes related improvements
to the VLAN infrastructure.
When CONFIG_VLAN_8021Q=n, CONFIG_OBJTOOL=y, and CONFIG_OBJTOOL_WERROR=y,
the following compilation error occurs:
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.o: error: objtool: parse_mirred.isra.0+0x370: mlx5e_tc_act_vlan_add_push_action() missing __noreturn in .c/.h or NORETURN() in noreturns.h
The error occurs because objtool cannot determine that unreachable BUG()
calls in VLAN code paths are actually dead code when VLAN support is
disabled.
First patch makes is_vlan_dev() a stub when VLAN is not configured,
allows compile-out of VLAN-dependent dead code paths and resolves the
objtool compilation error.
Second patch replaces BUG() calls with WARN_ON_ONCE(), as the usage of
BUG() should be avoided.
Third patch uses the "kernel" way of testing whether an option is
configured as builtin/module, instead of open-coding it.
v2: https://lore.kernel.org/20250610072611.1647593-1-gal@nvidia.com/
====================
Link: https://patch.msgid.link/20250616132626.1749331-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The header currently tests the VLAN core with an explicit pair of 'if
defined' checks:
#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
Instead, use IS_ENABLED() which is the kernel way to test whether an
option is configured as builtin/module.
This is purely cosmetic – no functional changes.
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250616132626.1749331-4-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_VLAN_8021Q=n, a set of stub helpers are used, three of these
helpers use BUG() unconditionally.
This code should not be reached, as callers of these functions should
always check for is_vlan_dev() first, but the usage of BUG() is not
recommended, replace it with WARN_ON() instead.
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250616132626.1749331-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a stub implementation of is_vlan_dev() that returns false when
VLAN support is not compiled in (CONFIG_VLAN_8021Q=n).
This allows us to compile-out VLAN-dependent dead code when it is not
needed.
This also resolves the following compilation error when:
* CONFIG_VLAN_8021Q=n
* CONFIG_OBJTOOL=y
* CONFIG_OBJTOOL_WERROR=y
drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.o: error: objtool: parse_mirred.isra.0+0x370: mlx5e_tc_act_vlan_add_push_action() missing __noreturn in .c/.h or NORETURN() in noreturns.h
The error occurs because objtool cannot determine that unreachable BUG()
(which doesn't return) calls in VLAN code paths are actually dead code
when VLAN support is disabled.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250616132626.1749331-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-5-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-4-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an integer return value to mcp251x_write_bits() and use it to
propagate the one returned by mcp251x_spi_write(). Return that value on
error in the request() GPIO callback.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-3-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-2-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-1-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gve_adminq_issue_cmd(), return -EINVAL instead of 0 when an unknown
admin queue command opcode is encountered.
This prevents the function from silently succeeding on invalid input
and prevents undefined behavior by ensuring the function fails gracefully
when an unrecognized opcode is provided.
These changes improve error handling.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250616054504.1644770-2-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Correct spelling and improves the clarity of comments
"confiugration" -> "configuration"
"spilt" -> "split"
"It if is 0" -> "If it is 0"
"DQ" -> "DQO" (correct abbreviation)
- Clarify BIT(0) flag usage in gve_get_priv_flags()
- Replaced hardcoded array size with GVE_NUM_PTYPES
for clarity and maintainability.
These changes are purely cosmetic and do not affect functionality.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250616054504.1644770-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add ipv4 support to the recently added chunks tests, which was added as
ipv6 only.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250615203511.591438-3-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trivial fix to a couple of outdated netmem comments. No code changes,
just more accurately describing current code.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250615203511.591438-1-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit adds a new kernel selftest to verify RTNLGRP_IPV4_MCADDR
and RTNLGRP_IPV6_MCADDR notifications. The test works by adding and
removing a dummy interface and then confirming that the system
correctly receives join and removal notifications for the 224.0.0.1
and ff02::1 multicast addresses.
The test relies on the iproute2 version to be 6.13+.
Tested by the following command:
$ vng -v --user root --cpus 16 -- \
make -C tools/testing/selftests TARGETS=net
TEST_PROGS=rtnetlink_notification.sh \
TEST_GEN_PROGS="" run_tests
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Yuyang Huang <yuyanghuang@google.com>
Link: https://patch.msgid.link/20250614053522.623820-1-yuyanghuang@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Álvaro Fernández Rojas says:
====================
net: dsa: b53: fix BCM5325 support
These patches get the BCM5325 switch working with b53.
The existing brcm legacy tag only works with BCM63xx switches.
We need to add a new legacy tag for BCM5325 and BCM5365 switches, which
require including the FCS and length.
I'm not really sure that everything here is correct since I don't work for
Broadcom and all this is based on the public datasheet available for the
BCM5325 and my own experiments with a Huawei HG556a (BCM6358).
Both sets of patches have been merged due to the change requested by Jonas
about BRCM_HDR register access depending on legacy tags.
====================
Link: https://patch.msgid.link/20250614080000.1884236-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the datasheet, BCM5325 uses B53_PD_MODE_CTRL_25 register to
disable clocking to individual PHYs.
Only ports 1-4 can be enabled or disabled and the datasheet is explicit
about not toggling BIT(0) since it disables the PLL power and the switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250614080000.1884236-15-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPU port should be B53_CPU_PORT instead of B53_CPU_PORT_25 for
B53_PVLAN_PORT_MASK register.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-14-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 doesn't implement UC_FLOOD_MASK, MC_FLOOD_MASK and IPMC_FLOOD_MASK
registers.
This has to be handled differently with other pages and registers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250614080000.1884236-13-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 doesn't implement GMII_PORT_OVERRIDE_CTRL register so we should
avoid reading or writing it.
PORT_OVERRIDE_RX_FLOW and PORT_OVERRIDE_TX_FLOW aren't defined on BCM5325
and we should use PORT_OVERRIDE_LP_FLOW_25 instead.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-12-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Older switches don't implement BRCM_HDR register so we should avoid
reading or writing it.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-11-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 doesn't implement DIS_LEARNING register so we should avoid reading
or writing it.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-10-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 doesn't implement SWITCH_CTRL register so we should avoid reading
or writing it.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-8-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 and BCM5365 are part of a much older generation of switches which,
due to their limited number of ports and VLAN entries (up to 256) allowed
a single 64-bit register to hold a full ARL entry.
This requires a little bit of massaging when reading, writing and
converting ARL entries in both directions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-6-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to be able to differentiate the BCM5325 variants because:
- BCM5325M switches lack the ARLIO_PAGE->VLAN_ID_IDX register.
- BCM5325E have less 512 ARL buckets instead of 1024.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250614080000.1884236-5-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 46c5176c58 ("net: dsa: b53: support legacy tags") introduced
support for legacy tags, but it turns out that BCM5325 and BCM5365
switches require the original FCS value and length, so they have to be
treated differently.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-4-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for legacy Broadcom FCS tags, which are similar to
DSA_TAG_PROTO_BRCM_LEGACY.
BCM5325 and BCM5365 switches require including the original FCS value and
length, as opposed to BCM63xx switches.
Adding the original FCS value and length to DSA_TAG_PROTO_BRCM_LEGACY would
impact performance of BCM63xx switches, so it's better to create a new tag.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250614080000.1884236-3-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move brcm_leg_tag_rcv() definition to top.
This function is going to be shared between two different tags.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-2-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The normal fsck code doesn't call key_visible_in_snapshot() with an
empty list of snapshot IDs seen (the current snapshot ID will always be
on the list), but str_hash_repair_key() ->
bch2_get_snapshot_overwrites() can, and that's totally fine as long as
we check for it.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Remove 3rd argument in prepare_seq_file() to clean up the code a bit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20250615004719.GE3011112@ZenIV
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The INVLPGB instruction has limits on how many pages it can invalidate
at once. That limit is enumerated in CPUID, read by the kernel, and
stored in 'invpgb_count_max'. Ranged invalidation, like
invlpgb_kernel_range_flush() break up their invalidations so
that they do not exceed the limit.
However, early boot code currently attempts to do ranged
invalidation before populating 'invlpgb_count_max'. There is a
for loop which is basically:
for (...; addr < end; addr += invlpgb_count_max*PAGE_SIZE)
If invlpgb_kernel_range_flush is called before the kernel has read
the value of invlpgb_count_max from the hardware, the normally
bounded loop can become an infinite loop if invlpgb_count_max is
initialized to zero.
Fix that issue by initializing invlpgb_count_max to 1.
This way INVPLGB at early boot time will be a little bit slower
than normal (with initialized invplgb_count_max), and not an
instant hang at bootup time.
Fixes: b7aa05cbdc ("x86/mm: Add INVLPGB support code")
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20250606171112.4013261-3-riel%40surriel.com
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath12k_wmi_fw_stats_process() host waits until all events received. In
case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
consequently the requestor would be blocked until time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
directly; if not, follow the old way.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-4-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_wmi_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever
reason (say ar->num_started_vdevs is 0 or firmware bug etc.) the following
condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time
when firmware stats is requested again, even if everything is working
fine, failure is expected due to the condition above will never be
satisfied.
The same applies to num_bcn as well.
Change to use non-static counters and reset them each time before firmware
stats is requested.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-3-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_get_fw_stats() is busy polling fw_stats_done flag while waiting
firmware finishing sending all events. This is not good as CPU is
monopolized and kept burning during the wait.
Change to the completion mechanism to fix it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Reported-by: Grégoire Stein <gregoire.s93@live.fr>
Closes: https://lore.kernel.org/ath12k/AS8P190MB120575BBB25FCE697CD7D4988763A@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Tested-by: Grégoire Stein <gregoire.s93@live.fr>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-2-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Regarding the firmware stats events handling, the comment in
ath12k_mac_get_fw_stats() says host determines whether all events have been
received based on 'end' tag in TLV. This is wrong as there is no such tag
at all, actually host makes the decision totally by itself based on the
stats type and active pdev/vdev counts etc.
Fix it to correctly reflect the logic.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-1-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of ML connection, currently all useful links are activated at
ASSOC stage:
ieee80211_set_active_links(vif, ieee80211_vif_usable_links(vif))
this results in firmware crash when the number of links activated on the
same device is more than supported.
Since firmware supports activating at most 2 links for a ML connection,
to avoid firmware crash, host needs to select 2 links out of the useful
links. As the assoc link has already been chosen, the question becomes
how to determine partner links. A straightforward principle applied
here is that the resulted combination should achieve the best throughput.
For that purpose, ideally various factors like bandwidth, RSSI etc should
be considered. But that would be too complicate. To make it easy, the
choice is to only take hardware modes into consideration.
The SBS (single band simultaneously) mode frequency range covers 5 GHz
and 6 GHz bands. In this mode, the two individual MACs are both active,
with one working on 5g-high band and the other on 5g-low band (from
hardware perspective 5 GHz and 6 GHz bands are referred to as a 'large'
single 5 GHz band). The DBS (dual band simultaneously) mode covers 2 GHz
band and the 'large' 5 GHz band, with one MAC working on 2 GHz band and
the other working on 5 GHz band or 6 GHz band. Since 5,6 GHz bands could
provide higher bandwidth than 2 GHz band, the preference is given to SBS
mode. Other hardware modes results in only one working MAC at any given
time, so it is chosen only when both SBS are DBS are not possible.
For each hardware mode, if there are more than one partner candidate,
just choose the first one.
For now only single device MLO case is handled as it is easy. Other cases
could be addressed in the future.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-6-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of two links established on the same device in an ML connection,
depending on device's hardware mode capability, it is possible that both
links fall on the same MAC. Currently, no specific action is taken to
address this but just keep both links active. However this would result
in lower throughput compared to even one link, because switching between
these two links on the resulted MAC significantly impacts throughput.
Check if both links fall in the frequency range of a single MAC. If
so, send WMI_MLO_LINK_SET_ACTIVE_CMDID command to firmware such that
firmware can deactivate one of them. Note the decision of which link
getting deactivated is made by firmware, host only sends the vdev
lists.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-5-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
