Set the glitch threshold by DTS property and keep the existing default
behavior if the 'debounce-delay-us' is not present.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250923143746.2857292-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support the debounce-delay-us property.
Drivers must convert this value to IPG clock cycles and map it to one of
the four discrete thresholds exposed by the TSC_DEBUG_MODE2 register:
0: 8191 IPG cycles
1: 4095 IPG cycles
2: 2047 IPG cycles
3: 1023 IPG cycles
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250923143746.2857292-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for glitch delay configuration. A detected signal is valid
only if it remains stable longer than the configured delay; otherwise,
it is considered a glitch.
This property was introduced for the i.MX6UL touchscreen controller (TSC),
which provides a hardware deglitch filter with four thresholds depending
on the IPG clock frequency. In this use case, the IPG clock rate is 66 MHz,
resulting in thresholds of 124 µs, 62 µs, 31 µs, and 15 µs, which requires
a property with microsecond-level resolution.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250923143746.2857292-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
sifive:
Reduce the number of fences issued while flushing. Samuel reports that
this is approximately a 15% speed-up.
ax45mp:
Fix the binding so that it permits the cache-sets setting used by the
recently added QiLai SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRh246EGq/8RLhDjO14tDGHoIJi0gUCaNQvGgAKCRB4tDGHoIJi
0mRQAQCCZsvM+vnC5OasyRbwNzt1WTXdRqXodP81pwvA4PeCswEAlIrvpTN85JX/
AG3mt64AzoVTakFvwjhcP3GHOHS8mw4=
=PX57
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=It/E
-----END PGP SIGNATURE-----
Merge tag 'riscv-cache-for-v6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers
RISC-V cache drivers for v6.18
sifive:
Reduce the number of fences issued while flushing. Samuel reports that
this is approximately a 15% speed-up.
ax45mp:
Fix the binding so that it permits the cache-sets setting used by the
recently added QiLai SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-cache-for-v6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
cache: sifive_ccache: Optimize cache flushes
dt-bindings: cache: ax45mp: add 2048 as a supported cache-sets value
Link: https://lore.kernel.org/r/20250924-relenting-aqua-a4a93b89809e@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Use for_each_online_cpu() instead of for_each_cpu() in qbman
- Update FSL QUICC ENGINE GPIO driver to a standard platform driver
and stop using legacy-of-mm-gpiochip.h header
- Misc fixes on bus/fsl-mc
-----BEGIN PGP SIGNATURE-----
iJIEABYKADoWIQQQ/+b4s5DeF6zCYyNoqS/rAbjdeAUCaNQTmBwcY2hyaXN0b3Bo
ZS5sZXJveUBjc2dyb3VwLmV1AAoJEGipL+sBuN14UZABAKSmuSrlq3ErA/76SfYU
vwqpn2OnQAWfb5ttS3teCnpqAQDwSOzhT2wO0EtK5HPnA9zC/iB8FeDLxtMIXFuW
vvcMCA==
=ECnN
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Zmaw
-----END PGP SIGNATURE-----
Merge tag 'soc_fsl-6.18-1' of https://github.com/chleroy/linux into soc/drivers
FSL SOC Changes for 6.18:
- Use for_each_online_cpu() instead of for_each_cpu() in qbman
- Update FSL QUICC ENGINE GPIO driver to a standard platform driver
and stop using legacy-of-mm-gpiochip.h header
- Misc fixes on bus/fsl-mc
* tag 'soc_fsl-6.18-1' of https://github.com/chleroy/linux:
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
bus: fsl-mc: Replace snprintf and sprintf with sysfs_emit in sysfs show functions
bus: fsl-mc: Check return value of platform_get_resource()
Link: https://lore.kernel.org/r/26615a15-3494-435f-b0c1-861122b4b5e1@csgroup.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"The data line must be sampled" makes much more sense than what was
previously written, and given that "s" and "d" are neighbors on the
QWERTY keybord, it was probably a typo.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://lore.kernel.org/r/20250923-ps2-typo-v1-1-03d2468acc32@posteo.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the module parameter slider_balance is set to the performance
slider value of 0, the SoC slider profile switches to the performance
mode.
This can cause the Linux power-profiles-daemon to change the system
power mode to performance from balanced mode. This happens when there
is only one platform profile registered as there will be no conflict
with other platform profiles.
Same issue occurs when the slider_balance is set to the power-saver
slider value.
Prevent module parameter slider_balance from overlapping with
performance and power-saver slider values by adding range validation.
Return an error when an invalid value is provided.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20250923205631.3056590-1-srinivas.pandruvada@linux.intel.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The return value from tegra_bpmp_transfer() indicates the success or
failure of the IPC transaction with BPMP. If the transaction succeeded, we
also need to check the actual command's result code.
If we don't have error handling for tegra_bpmp_transfer(), we will set the
pcie->ep_state to EP_STATE_ENABLED even when the tegra_bpmp_transfer()
command fails. Thus, the pcie->ep_state will get out of sync with reality,
and any further PERST# assert + deassert will be a no-op and will not
trigger the hardware initialization sequence.
This is because pex_ep_event_pex_rst_deassert() checks the current
pcie->ep_state, and does nothing if the current state is already
EP_STATE_ENABLED.
Thus, it is important to have error handling for tegra_bpmp_transfer(),
such that the pcie->ep_state can not get out of sync with reality, so that
we will try to initialize the hardware not only during the first PERST#
assert + deassert, but also during any succeeding PERST# assert + deassert.
One example where this fix is needed is when using a rock5b as host.
During the initial PERST# assert + deassert (triggered by the bootloader on
the rock5b) pex_ep_event_pex_rst_deassert() will get called, but for some
unknown reason, the tegra_bpmp_transfer() call to initialize the PHY fails.
Once Linux has been loaded on the rock5b, the PCIe driver will once again
assert + deassert PERST#. However, without tegra_bpmp_transfer() error
handling, this second PERST# assert + deassert will not trigger the
hardware initialization sequence.
With tegra_bpmp_transfer() error handling, the second PERST# assert +
deassert will once again trigger the hardware to be initialized and this
time the tegra_bpmp_transfer() succeeds.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-8-cassel@kernel.org
Tegra already defines all BARs except BAR0 as BAR_RESERVED. This is
sufficient for pci-epf-test to not allocate backing memory and to not call
set_bar() for those BARs. However, marking a BAR as BAR_RESERVED does not
mean that the BAR gets disabled.
The host side driver, pci_endpoint_test, simply does an ioremap for all
enabled BARs and will run tests against all enabled BARs, so it will run
tests against the BARs marked as BAR_RESERVED.
After running the BAR tests (which will write to all enabled BARs), the
inbound address translation is broken. This is because the tegra controller
exposes the ATU Port Logic Structure in BAR4, so when BAR4 is written, the
inbound address translation settings get overwritten.
To avoid this, implement the dw_pcie_ep_ops .init() callback and start off
by disabling all BARs (pci-epf-test will later enable/configure BARs that
are not defined as BAR_RESERVED).
This matches the behavior of other PCIe endpoint drivers: dra7xx, imx6,
layerscape-ep, artpec6, dw-rockchip, qcom-ep, rcar-gen4, and uniphier-ep.
With this, the PCI endpoint kselftest test case CONSECUTIVE_BAR_TEST (which
was specifically made to detect address translation issues) passes.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-7-cassel@kernel.org
The "max_link_width", "current_link_speed", "current_link_width",
"secondary_bus_number", and "subordinate_bus_number" sysfs files all access
config registers, but they don't check the runtime PM state. If the device
is in D3cold or a parent bridge is suspended, we may see -EINVAL, bogus
values, or worse, depending on implementation details.
Wrap these access in pci_config_pm_runtime_{get,put}() like most of the
rest of the similar sysfs attributes.
Notably, "max_link_speed" does not access config registers; it returns a
cached value since d2bd39c045 ("PCI: Store all PCIe Supported Link
Speeds").
Fixes: 56c1af4606 ("PCI: Add sysfs max_link_speed/width, current_link_speed/width, etc")
Signed-off-by: Brian Norris <briannorris@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250924095711.v2.1.Ibb5b6ca1e2c059e04ec53140cd98a44f2684c668@changeid
* kvm-arm64/selftests-6.18:
: .
: KVM/arm64 selftest updates for 6.18:
:
: - Large update to run EL1 selftests at EL2 when possible
: (20250917212044.294760-1-oliver.upton@linux.dev)
:
: - Work around lack of ID_AA64MMFR4_EL1 trapping on CPUs
: without FEAT_FGT
: (20250923173006.467455-1-oliver.upton@linux.dev)
:
: - Additional fixes and cleanups
: (20250920-kvm-arm64-id-aa64isar3-el1-v1-0-1764c1c1c96d@kernel.org)
: .
KVM: arm64: selftests: Cover ID_AA64ISAR3_EL1 in set_id_regs
KVM: arm64: selftests: Remove a duplicate register listing in set_id_regs
KVM: arm64: selftests: Cope with arch silliness in EL2 selftest
KVM: arm64: selftests: Add basic test for running in VHE EL2
KVM: arm64: selftests: Enable EL2 by default
KVM: arm64: selftests: Initialize HCR_EL2
KVM: arm64: selftests: Use the vCPU attr for setting nr of PMU counters
KVM: arm64: selftests: Use hyp timer IRQs when test runs at EL2
KVM: arm64: selftests: Select SMCCC conduit based on current EL
KVM: arm64: selftests: Provide helper for getting default vCPU target
KVM: arm64: selftests: Alias EL1 registers to EL2 counterparts
KVM: arm64: selftests: Create a VGICv3 for 'default' VMs
KVM: arm64: selftests: Add unsanitised helpers for VGICv3 creation
KVM: arm64: selftests: Add helper to check for VGICv3 support
KVM: arm64: selftests: Initialize VGICv3 only once
KVM: arm64: selftests: Provide kvm_arch_vm_post_create() in library code
Signed-off-by: Marc Zyngier <maz@kernel.org>
We have a couple of writable bitfields in ID_AA64ISAR3_EL1 but the
set_id_regs selftest does not cover this register at all, add coverage.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Currently we list the main set of registers with bits we test three
times, once in the test_regs array which is used at runtime, once in the
guest code and once in a list of ARRAY_SIZE() operations we use to tell
kselftest how many tests we plan to execute. This is needlessly fiddly,
when adding new registers as the test_cnt calculation is formatted with
two registers per line. Instead count the number of bitfields in the
register arrays at runtime.
The existing code subtracts ARRAY_SIZE(test_regs) from the number of
tests to account for the terminating FTR_REG_END entries in the per
register arrays, the new code accounts for this when enumerating.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Implementations without FEAT_FGT aren't required to trap the entire ID
register space when HCR_EL2.TID3 is set. This is a terrible idea, as the
hypervisor may need to advertise the absence of a feature to the VM
using a negative value in a signed field, FEAT_E2H0 being a great
example of this.
Cope with uncooperative implementations in the EL2 selftest by accepting
a zero value when FEAT_FGT is absent and otherwise only tolerating the
expected nonzero value.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add an embarrassingly simple selftest for sanity checking KVM's VHE EL2
and test that the ID register bits are consistent with HCR_EL2.E2H being
RES1.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Take advantage of VHE to implicitly promote KVM selftests to run at EL2
with only slight modification. Update the smccc_filter test to account
for this now that the EL2-ness of a VM is visible to tests.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Initialize HCR_EL2 such that EL2&0 is considered 'InHost', allowing the
use of (mostly) unmodified EL1 selftests at EL2.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Configuring the number of implemented counters via PMCR_EL0.N was a bad
idea in retrospect as it interacts poorly with nested. Migrate the
selftest to use the vCPU attribute instead of the KVM_SET_ONE_REG
mechanism.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Arch timer registers are redirected to their hypervisor counterparts
when running in VHE EL2. This is great, except for the fact that the
hypervisor timers use different PPIs. Use the correct INTIDs when that
is the case.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
HVCs are taken within the VM when EL2 is in use. Ensure tests use the
SMC instruction when running at EL2 to interact with the host.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The default vCPU target in KVM selftests is pretty boring in that it
doesn't enable any vCPU features. Expose a helper for getting the
default target to prepare for cramming in more features. Call
KVM_ARM_PREFERRED_TARGET directly from get-reg-list as it needs
fine-grained control over feature flags.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Itaru Kitayama <itaru.kitayama@fujitsu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
FEAT_VHE has the somewhat nice property of implicitly redirecting EL1
register aliases to their corresponding EL2 representations when E2H=1.
Unfortunately, there's no such abstraction for userspace and EL2
registers are always accessed by their canonical encoding.
Introduce a helper that applies EL2 redirections to sysregs and use
aggressive inlining to catch misuse at compile time. Go a little past
the architectural definition for ease of use for test authors (e.g. the
stack pointer).
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Start creating a VGICv3 by default unless explicitly opted-out by the
test. While having an interrupt controller is nice, the real benefit
here is clearing a hurdle for EL2 VMs which mandate the presence of a
VGIC.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
vgic_v3_setup() has a good bit of sanity checking internally to ensure
that vCPUs have actually been created and match the dimensioning of the
vgic itself. Spin off an unsanitised setup and initialization helper so
vgic initialization can be wired in around a 'default' VM's vCPU
creation.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Introduce a proper predicate for probing VGICv3 by performing a 'test'
creation of the device on a dummy VM.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
vgic_v3_setup() unnecessarily initializes the vgic twice. Keep the
initialization after configuring MMIO frames and get rid of the other.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to compel the default usage of EL2 in selftests, move
kvm_arch_vm_post_create() to library code and expose an opt-in for using
MTE by default.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fix a locking issue in the cpufreq core introduced recently and
caught by lockdep (Christian Loehle).
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmjT1lESHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1dSsH/A7OtNoxf41xUXKBuHyJ/4x5vWVkOEBs
/yrjUicK3FCXsL5ZNkO0RfjA+blB9SHYpAuJFWKabXMVoMtL4K7ygHJrB5Oi+1/t
E927jCVg5YLndhkembWUgb2rpTzAfTKkYXKrjc7PR3dkebWeOeovU72RDOtl7MFw
r0phhcrYamjCV3GbxN1kwl6J3SfKTpBzWF/4eUBLfega7jDUpIEA6d9NQnQvyAnG
tlPdH9xy9WrIv7H6S3AOLmqgLgrJtYXY1r+FHVGCC7w0EjHDHOoYiI8U0+HIbGNc
75N0+JYhMzdkrg6kcZ8LyiiOxiWrwvZ/tGR2Mox5zjCstV/lktxdBDg=
=Hhlz
-----END PGP SIGNATURE-----
Merge tag 'pm-6.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Rafael:
"Fix a locking issue in the cpufreq core introduced recently and caught
by lockdep (Christian Loehle)"
* tag 'pm-6.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Initialize cpufreq-based invariance before subsys
-----BEGIN PGP SIGNATURE-----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=sOwE
-----END PGP SIGNATURE-----
Merge tag 'for-6.17-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more regression fix for a problem in zoned mode: mounting would
fail if the number of open and active zones reached a common limit
that didn't use to be checked"
* tag 'for-6.17-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: don't fail mount needlessly due to too many active zones
-----BEGIN PGP SIGNATURE-----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=kC8N
-----END PGP SIGNATURE-----
Merge tag '6.17-rc7-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- free_transport fix for disconnect races
- minor delayed work fix
* tag '6.17-rc7-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
smb: server: use disable_work_sync in transport_rdma.c
smb: server: don't use delayed_work for post_recv_credits_work
Now that AF_XDP functionality is fully implemented, advertise XSk XDP
feature and add .ndo_xsk_wakeup() callback to be able to use it with
this driver.
Co-developed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement Rx packet processing specific to AF_XDP ZC using the libeth
XSk infra. Initialize queue registers before allocating buffers to
avoid redundant ifs when updating the queue tail.
Co-developed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement the XSk transmit path using the libeth (libeth_xdp)
XSk infra.
When the NAPI poll is called, XSk Tx queues are polled first,
before regular Tx and Rx. They're generally faster to serve
and have higher priority comparing to regular traffic.
Co-developed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add functionality to setup an XSk buffer pool, including ability to
stop, reconfig and start only selected queues, not the whole device.
Pool DMA mapping is managed by libeth_xdp.
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement VC functions dedicated to enabling, disabling and configuring
not all but only selected queues.
Also, refactor the existing implementation to make the code more
modular. Introduce new generic functions for sending VC messages
consisting of chunks, in order to isolate the sending algorithm
and its implementation for specific VC messages.
Finally, rewrite the function for mapping queues to q_vectors using the
new modular approach to avoid copying the code that implements the VC
message sending algorithm.
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Co-developed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ6NaUOruQGUkvPdG4raS+Z+3y5EwUCaNNwBQAKCRAraS+Z+3y5
E8heAQDdJTR9rwAL7gD79cldlHP5PTmjyidLIoFG/efaGSbN1AD9EdvrykDU4xOG
aGaO8TooGUZf7vAL8tIFuMeydYvi/gM=
=Qu4T
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2025-09-23
We've added 9 non-merge commits during the last 33 day(s) which contain
a total of 10 files changed, 480 insertions(+), 53 deletions(-).
The main changes are:
1) A new bpf_xdp_pull_data kfunc that supports pulling data from
a frag into the linear area of a xdp_buff, from Amery Hung.
This includes changes in the xdp_native.bpf.c selftest, which
Nimrod's future work depends on.
It is a merge from a stable branch 'xdp_pull_data' which has
also been merged to bpf-next.
There is a conflict with recent changes in 'include/net/xdp.h'
in the net-next tree that will need to be resolved.
2) A compiler warning fix when CONFIG_NET=n in the recent dynptr
skb_meta support, from Jakub Sitnicki.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
selftests: drv-net: Pull data before parsing headers
selftests/bpf: Test bpf_xdp_pull_data
bpf: Support specifying linear xdp packet data size for BPF_PROG_TEST_RUN
bpf: Make variables in bpf_prog_test_run_xdp less confusing
bpf: Clear packet pointers after changing packet data in kfuncs
bpf: Support pulling non-linear xdp data
bpf: Allow bpf_xdp_shrink_data to shrink a frag from head and tail
bpf: Clear pfmemalloc flag when freeing all fragments
bpf: Return an error pointer for skb metadata when CONFIG_NET=n
====================
Link: https://patch.msgid.link/20250924050303.2466356-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the driver supports MSI, set the flag to true. This helps
pci_endpoint_test to use the optimal IRQ type when using
PCITEST_IRQ_TYPE_AUTO.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: splitted this change from the bug fix]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250922140822.519796-6-cassel@kernel.org
The pci_epc_raise_irq() supplies a MSI or MSI-X interrupt number in range
(1-N), as per the pci_epc_raise_irq() kdoc, where N is 32 for MSI.
But tegra_pcie_ep_raise_msi_irq() incorrectly uses the interrupt number as
the MSI vector. This causes wrong MSI vector to be triggered, leading to
the failure of PCI endpoint Kselftest MSI_TEST test case.
To fix this issue, convert the interrupt number to MSI vector.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-6-cassel@kernel.org
Alexey Gladkov says:
The modules.builtin.modinfo file is used by userspace (kmod to be specific) to
get information about builtin modules. Among other information about the module,
information about module aliases is stored. This is very important to determine
that a particular modalias will be handled by a module that is inside the
kernel.
There are several mechanisms for creating modalias for modules:
The first is to explicitly specify the MODULE_ALIAS of the macro. In this case,
the aliases go into the '.modinfo' section of the module if it is compiled
separately or into vmlinux.o if it is builtin into the kernel.
The second is the use of MODULE_DEVICE_TABLE followed by the use of the
modpost utility. In this case, vmlinux.o no longer has this information and
does not get it into modules.builtin.modinfo.
For example:
$ modinfo pci:v00008086d0000A36Dsv00001043sd00008694bc0Csc03i30
modinfo: ERROR: Module pci:v00008086d0000A36Dsv00001043sd00008694bc0Csc03i30 not found.
$ modinfo xhci_pci
name: xhci_pci
filename: (builtin)
license: GPL
file: drivers/usb/host/xhci-pci
description: xHCI PCI Host Controller Driver
The builtin module is missing alias "pci:v*d*sv*sd*bc0Csc03i30*" which will be
generated by modpost if the module is built separately.
To fix this it is necessary to add the generated by modpost modalias to
modules.builtin.modinfo. Fortunately modpost already generates .vmlinux.export.c
for exported symbols. It is possible to add `.modinfo` for builtin modules and
modify the build system so that `.modinfo` section is extracted from the
intermediate vmlinux after modpost is executed.
Link: https://patch.msgid.link/cover.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Since .vmlinux.export.c is used to add generated by modpost modaliases
for builtin modules the .vmlinux.export.o is no longer optional and
should always be created. The generation of this file is not dependent
on CONFIG_MODULES.
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/0e63a9c7741fe8217e4fd7c60afcf057ffa2ef5a.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
For some modules, modalias is generated using the modpost utility and
the section is added to the module file.
When a module is added inside vmlinux, modpost does not generate
modalias for such modules and the information is lost.
As a result kmod (which uses modules.builtin.modinfo in userspace)
cannot determine that modalias is handled by a builtin kernel module.
$ cat /sys/devices/pci0000:00/0000:00:14.0/modalias
pci:v00008086d0000A36Dsv00001043sd00008694bc0Csc03i30
$ modinfo xhci_pci
name: xhci_pci
filename: (builtin)
license: GPL
file: drivers/usb/host/xhci-pci
description: xHCI PCI Host Controller Driver
Missing modalias "pci:v*d*sv*sd*bc0Csc03i30*" which will be generated by
modpost if the module is built separately.
To fix this it is necessary to generate the same modalias for vmlinux as
for the individual modules. Fortunately '.vmlinux.export.o' is already
generated from which '.modinfo' can be extracted in the same way as for
vmlinux.o.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/28d4da3b0e3fc8474142746bcf469e03752c3208.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
At this point, if a symbol is compiled as part of the kernel,
information about which module the symbol belongs to is lost.
To save this it is possible to add the module name to the alias name.
It's not very pretty, but it's possible for now.
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Andreas Hindborg <a.hindborg@kernel.org>
Cc: Danilo Krummrich <dakr@kernel.org>
Cc: Alex Gaynor <alex.gaynor@gmail.com>
Cc: rust-for-linux@vger.kernel.org
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/1a0d0bd87a4981d465b9ed21e14f4e78eaa03ded.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
The blogic_pci_tbl structure is used by the MODULE_DEVICE_TABLE macro.
There is no longer a need to protect it with the MODULE condition, since
this no longer causes the compiler to warn about an unused variable.
To avoid warnings when -Wunused-const-variable option is used, mark it
as __maybe_unused for such configuration.
Cc: Khalid Aziz <khalid@gonehiking.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Suggested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://patch.msgid.link/fd8e30de07de79a4923ae967eaee5ba2f2fcef00.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Currently, we assume all the data for modules.builtin.modinfo are
available in vmlinux.o.
This makes it impossible for modpost, which is invoked after vmlinux.o,
to add additional module info.
This commit moves the modules.builtin.modinfo rule after modpost.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/cdb3e5b9a739666b755cd0097dc34ab69c350e51.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Keep the .modinfo section during linking, but strip it from the final
vmlinux.
Adjust scripts/mksysmap to exclude modinfo symbols from kallsyms.
This change will allow the next commit to extract the .modinfo section
from the vmlinux.unstripped intermediate.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/aaf67c07447215463300fccaa758904bac42f992.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Generate the intermediate vmlinux.unstripped regardless of
CONFIG_ARCH_VMLINUX_NEEDS_RELOCS.
If CONFIG_ARCH_VMLINUX_NEEDS_RELOCS is unset, vmlinux.unstripped and
vmlinux are identiacal.
This simplifies the build rule, and allows to strip more sections
by adding them to remove-section-y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/a48ca543fa2305bd17324f41606dcaed9b19f2d4.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
In the upcoming changes, the ELF_DETAILS macro will be extended with
the ".modinfo" section, which will cause an error:
>> s390x-linux-ld: .tmp_vmlinux1: warning: allocated section `.modinfo' not in segment
>> s390x-linux-ld: .tmp_vmlinux2: warning: allocated section `.modinfo' not in segment
>> s390x-linux-ld: vmlinux.unstripped: warning: allocated section `.modinfo' not in segment
This happens because the .vmlinux.info use :NONE to override the default
segment and tell the linker to not put the section in any segment at all.
To avoid this, we need to change the sections order that will be placed
in the default segment.
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506062053.zbkFBEnJ-lkp@intel.com/
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20d40a7a3a053ba06a54155e777dcde7fdada1db.1758182101.git.legion@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
