In the past, we use width and height to look up our PLL value.
But actually the actual clock check is also necessnary. There are
some resolutions that width and height same, but its clock different.
Add the clock check when using pll_table to determine the PLL value.
Fixes: da52605eea ("drm/hisilicon/hibmc: Add support for display engine")
Signed-off-by: Lin He <helin52@huawei.com>
Signed-off-by: Yongbang Shi <shiyongbang@huawei.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260509032302.2057227-5-shiyongbang@huawei.com
If there's no VGA output, this encoder modeset won't be called, which
will cause displaying data from GPU being cut off. It's actually a
common display config for DP and VGA, so move the vdac encoder modeset
to driver load stage.
Removed invalid bit configurations from `hibmc_display_ctrl`
Fixes: 5294967f4a ("drm/hisilicon/hibmc: Add support for VDAC")
Signed-off-by: Lin He <helin52@huawei.com>
Signed-off-by: Yongbang Shi <shiyongbang@huawei.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260509032302.2057227-4-shiyongbang@huawei.com
Our chip support KVM over IP feature, so hibmc driver need to support
displaying without any connectors plugged in. If no connectors are
connected, the vdac connector status should be set to 'connected' to
ensure proper KVM display functionality. Additionally, for
previous-generation products that may lack hardware link support and
thus cannot detect the monitor, the same approach should be applied
to ensure VGA display functionality.
* Add phys_state in the struct of dp and vdac to check physical outputs.
* The 'epoch_counter' of the vdac connector is incremented when the
physical status changes.
For get_modes: using BMC modes for connector if no display is attached to
phys VGA cable, otherwise use EDID modes by drm_connector_helper_get_modes,
because KVM doesn't provide EDID reads.
The polling mechanism for the KMS helper is enabled.
Fixes: 4c962bc929 ("drm/hisilicon/hibmc: Add vga connector detect functions")
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Closes: https://lore.kernel.org/all/0eb5c509-2724-4c57-87ad-74e4270d5a5a@suse.de/
Signed-off-by: Lin He <helin52@huawei.com>
Signed-off-by: Yongbang Shi <shiyongbang@huawei.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260509032302.2057227-3-shiyongbang@huawei.com
In the past, the link cap is updated in link training at encoder enable
stage, but the hibmc_dp_mode_valid() is called before it, which will use
DP link's rate and lanes. So add the hibmc_dp_update_caps() in
hibmc_dp_update_caps() to avoid some potential risks.
Fixes: 607805abfb ("drm/hisilicon/hibmc: add dp mode valid check")
Signed-off-by: Lin He <helin52@huawei.com>
Signed-off-by: Yongbang Shi <shiyongbang@huawei.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260509032302.2057227-2-shiyongbang@huawei.com
To perform copy, based on whether the platform supports service copy
engines, either MEM_COPY or XY_FAST_COPY_BLT instruction is used.
Length of both the instructions is same today and so they use a common
define EMIT_COPY_DW.
This is not true for the future platforms. Implement separate functions
which return the length of the instruction to help in preparing for it.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260511123746.616662-8-balasubramani.vivekanandan@intel.com
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Implement a function to return the length of the MEM_SET instruction.
This is to prepare for future platforms where the length of MEM_SET
instruction is expected to change.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260511123746.616662-7-balasubramani.vivekanandan@intel.com
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Implement a function which returns the length of XY_FAST_COLOR_BLT
instruction instead of hardcoding it inside the emit_clear_main_copy.
In future platforms, the length of this instruction is expected to
change and this patch helps in preparing for it.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260511123746.616662-6-balasubramani.vivekanandan@intel.com
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
The FIXME says that xe_engine_snapshot_print.. is accessing persistent
driver data, unlike what the FIXME says that it does. Drop the FIXME
since the current code is not going to access the hardware while
dumping.
More details about this patch:
https://patchwork.freedesktop.org/patch/703884/?series=161407&rev=1
The starting two feedbacks make sense and the original patch is wrong
in adding those changes, but the last feedback is the one which
highlights the point.
Signed-off-by: Shekhar Chauhan <shekhar.chauhan@intel.com>
Reviewed-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Link: https://patch.msgid.link/20260512055508.1380191-1-shekhar.chauhan@intel.com
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Document the designated initializer behavior for overlapping storage
between NAME and MEMBERS, and clarify the implications for static
initialization to help avoid unintended overwrites.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/agD0R-kNbg9YMOCT@kspp
Signed-off-by: Kees Cook <kees@kernel.org>
Remove the rtw_txq_dequeue helper. It's a wrapper around
ieee80211_tx_dequeue with just one caller.
Call ieee80211_tx_dequeue directly in rtw_txq_push. There's no need to
fetch txq for every frame, we can do this once outside of the rcu lock.
Make the loop variable i unsigned long, it should have the same type as
frames.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260507082238.889656-1-martin@kaiser.cx
The radiotap headroom is allocated only if IEEE80211_CONF_MONITOR is set.
However, it is potentially racing that SKB allocation without radiotap
headroom but adding radiotap from matched PPDU status of another SKB.
Add a check to avoid the case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-15-pkshih@realtek.com
The format of PHY status IE-10 for RTL8922D is different from earlier
chips. Fortunately only starting bit is different, but the layout is the
same. Get the VHT/HE SIG-A value by corresponding mask accordingly.
The IE-09 format of generation 0 and 1 are totally the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-14-pkshih@realtek.com
Hardware reports a list of PHY status IE. In monitor mode, IE-09 of
PHY status is enabled, and the report contains trailing 8-byte zeros,
causing failed to parse and drop all IE information.
The 8 zeros are recognize as IE type 0, but length of type 0 must be
not 8 (reference to rtw89_phy_gen_def::physt_ie_len[0]).
Check and skip them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-13-pkshih@realtek.com
To capture HE-MU packets, set BSS color and AID for specific connected
station.
The writing format: <bss color> <aid>
For example,
$ echo 0x4 0x16 > monitor_opts
Read this entry to get current setting:
bss_color=0x4 aid=0x16
By the way, add another sec2() function to create debugfs entries to
prevent running smatch timeout.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-11-pkshih@realtek.com
Fill HE radiotap by PHY status IE-09/IE-10 which contains HE SIG-A/SIG-B
respectively.
The IE-10 may contain two content channels (if bandwidth is larger than
40MHz), and starting address of second content channel can be calculated by
length of first content channel containing up to 15 user fields with 8-byte
alignment.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-9-pkshih@realtek.com
The IE-09/IE-10 of PHY status contain SIG-A/SIG-B respectively, so enable
them in monitor mode to have rich information. If the parser detects
length invalid, ignore to reference IE-09/IE-10 to prevent accessing out
of range.
The RTL8922D is generation 2 of PHY status, which doesn't report SIG-B by
IE-10, so not enable it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-6-pkshih@realtek.com
Both RTL8922A and RTL8922D are WiFi 7 chips, but their IE length of PHY
status are different. Define them accordingly.
Generation 0: WiFi 6 chips
Generation 1: WiFi 7 RTL8922A
Generation 2: WiFi 7 RTL8922D
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260506131000.1706298-5-pkshih@realtek.com
There is one USB2.0 host in K3 SoC which use DWC3 IP but only provide
USB2.0 functionality, and with only one USB2 PHY connected.
The USB2.0 controller on Pico-ITX board connects to a Terminus FE1.1 Hub
which fully USB2.0 protocol compliant and provides 4 ports.
Link: https://patch.msgid.link/20260330-02-k3-usb20-dts-v2-1-46af262fb4a9@kernel.org
Signed-off-by: Yixun Lan <dlan@kernel.org>
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
wilco_ec event driver.
Fixes: 27d58498f6 ("platform/chrome: wilco_ec: event: Convert to a platform driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/2076666.usQuhbGJ8B@rafael.j.wysocki
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
chromeos_tbmc driver.
Fixes: a2676ead25 ("platform/chrome: chromeos_tbmc: Convert to a platform driver")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/1875121.VLH7GnMWUR@rafael.j.wysocki
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
chromeos_privacy_screen driver.
Fixes: d3c2872ae3 ("platform/chrome: Convert ChromeOS privacy-screen driver to platform")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/3357444.5fSG56mABF@rafael.j.wysocki
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Ivan Vecera says:
====================
dpll: rework fractional frequency offset reporting
Rework how the fractional frequency offset (FFO) is reported in
the DPLL subsystem.
Both fractional-frequency-offset (PPM) and
fractional-frequency-offset-ppt (PPT) attributes are now present at
the top level of a pin and inside each pin-parent-device nest. They
carry the same measurement at different precisions.
Introduce enum dpll_ffo_type and struct dpll_ffo_param to distinguish
FFO contexts: DPLL_FFO_PORT_RXTX_RATE for the RX vs TX symbol rate
offset at the top level, and DPLL_FFO_PIN_DEVICE for the pin vs
parent DPLL offset in the nest. Drivers declare which types they
support via the supported_ffo bitmask in dpll_pin_ops; the core only
calls ffo_get for opted-in types.
Patch 1 adds the type-safe FFO API, updates the YAML spec, netlink
handling, and documentation, and converts mlx5 and zl3073x drivers.
Patch 2 implements the nested FFO for zl3073x using the
dpll_df_offset_x register with ref_ofst=1, providing 2^-48
resolution. The old per-reference frequency measurement is removed
as it was redundant with measured-frequency.
====================
Link: https://patch.msgid.link/20260511155816.99936-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the per-reference frequency offset measurement (which was
redundant with measured-frequency) with a direct read of the DPLL's
delta frequency offset vs its tracked input reference.
The new implementation uses the dpll_df_offset_x register with
ref_ofst=1 via the dpll_df_read_x semaphore mechanism. This
provides 2^-48 resolution (~3.5 fE) and reports the actual
frequency difference between the DPLL and its active input.
Switch supported_ffo from DPLL_FFO_PORT_RXTX_RATE to
DPLL_FFO_PIN_DEVICE so FFO is reported only in the per-parent
context for the active input pin.
Use atomic64_t for freq_offset to prevent torn reads on 32-bit
architectures between the periodic worker and netlink callbacks.
Rewrite ffo_check to compare the cached df_offset converted to PPT
instead of using the old per-reference measurement. Remove the
ref_ffo_update periodic measurement and the ref ffo field since
they are no longer needed.
Changes v3 -> v4:
- Switch to DPLL_FFO_PIN_DEVICE, remove dpll=NULL guard
- Use atomic64_t for freq_offset (torn read on 32-bit)
Reviewed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260511155816.99936-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add both fractional-frequency-offset (PPM) and
fractional-frequency-offset-ppt (PPT) attributes to the
pin-parent-device nested attribute set, alongside the existing
top-level pin attributes. Both carry the same measurement at
different precisions.
Introduce enum dpll_ffo_type and struct dpll_ffo_param to
distinguish FFO contexts: DPLL_FFO_PORT_RXTX_RATE for the RX vs
TX symbol rate offset reported at the top level, and
DPLL_FFO_PIN_DEVICE for the pin vs parent DPLL offset reported
in the pin-parent-device nest.
Add a supported_ffo bitmask to struct dpll_pin_ops so drivers
declare which FFO types they support. The core only calls ffo_get
for types the driver has opted into, eliminating the need for
per-driver NULL pointer guards. Validate at pin registration time
that supported_ffo is not set without an ffo_get callback.
Update mlx5 (DPLL_FFO_PORT_RXTX_RATE) and zl3073x
(DPLL_FFO_PORT_RXTX_RATE) drivers to use the new API.
Add documentation for both FFO types to dpll.rst.
Changes v3 -> v4:
- Replace dpll=NULL overloading with enum dpll_ffo_type and
struct dpll_ffo_param (Jakub Kicinski)
- Add supported_ffo opt-in bitmask in dpll_pin_ops for fail-close
driver validation (Jakub Kicinski)
- Add WARN_ON in dpll_pin_register for supported_ffo without
ffo_get callback
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260511155816.99936-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When updating the driver to match latest datasheet to suspend access to
URAM when suspending DMA transfers a corner-case was missed, URAM access
will not be suspended if WoL is enabled. This lead to the error message
(correctly) being triggered as URAM access is not suspended even tho
it's requested as part of stopping DMA.
Avoid checking if URAM access is suspended and printing the error
message if WoL is enabled when we suspend the system, as we know it will
not be.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdWnjV%3DHGE1o08zLhUfTgOSene5fYx1J5GG10mB%2BToq8qg@mail.gmail.com/
Fixes: 353d8e7989 ("net: ethernet: ravb: Suspend and resume the transmission flow")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ethnl_bitmap32_not_zero() should return true if some bit in [start, end)
is set:
- Fix inverted memchr_inv() sense: return true when the scan finds a
non-zero byte, not when the middle words are all zero.
- Return false for an empty interval (end <= start).
- When end is 32-bit aligned, indices in [start, end) do not include any
bits from map[end_word]; return false after earlier checks found no
non-zero data.
Fixes: 10b518d4e6 ("ethtool: netlink bitset handling")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The smc_msg_event tracepoint class, shared by smc_tx_sendmsg and
smc_rx_recvmsg, unconditionally dereferences smc->conn.lnk:
__string(name, smc->conn.lnk->ibname)
conn->lnk is only set for SMC-R; for SMC-D it is NULL. Other code on
these paths already handles this (e.g. !conn->lnk in
SMC_STAT_RMB_TX_SIZE_SMALL()). With the tracepoint enabled, the first
sendmsg()/recvmsg() on an SMC-D socket crashes:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [...]
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
trace_event_raw_event_smc_msg_event (net/smc/smc_tracepoint.h:44)
smc_rx_recvmsg (net/smc/smc_rx.c:515)
smc_recvmsg (net/smc/af_smc.c:2859)
__sys_recvfrom (net/socket.c:2315)
__x64_sys_recvfrom (net/socket.c:2326)
do_syscall_64
The faulting address 0x3e0 is offsetof(struct smc_link, ibname),
confirming the NULL ->lnk deref. Enabling the tracepoint requires
root, but the trigger itself is unprivileged: socket(AF_SMC, ...) has
no capability check, and SMC-D negotiation needs no admin step on
s390 or on x86 with the loopback ISM device loaded.
Log an empty device name for SMC-D instead of dereferencing NULL.
Fixes: aff3083f10 ("net/smc: Introduce tracepoints for tx and rx msg")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A logic flaw in __smc_setsockopt() allows a local unprivileged user to
cause a Denial of Service (DoS) by holding the socket lock indefinitely.
The function __smc_setsockopt() calls copy_from_sockptr() while holding
lock_sock(sk). By passing a userfaultfd-monitored memory page (or
FUSE-backed memory on systems where unprivileged userfaultfd is disabled)
as the optval, an attacker can halt execution during the copy operation,
keeping the lock held.
Combined with asynchronous tear-down operations like shutdown(), this
exhausts the kernel wq (kworkers) and triggers the hung task watchdog.
[ 240.123456] INFO: task kworker/u8:2 blocked for more than 120 seconds.
[ 240.123489] Call Trace:
[ 240.123501] smc_shutdown+...
[ 240.123512] lock_sock_nested+...
This patch moves the user-space copy outside the lock_sock() critical
section to prevent the issue.
Fixes: a6a6fe27ba ("net/smc: Dynamic control handshake limitation by socket options")
Signed-off-by: Nicolò Coccia <n.coccia96@gmail.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add chip info entry for the Realtek RTL8367SB switch. This device has
chip ID 0x6367 and version 0x0010. It exposes two external interfaces:
port 6 supports MII, TMII, RMII, RGMII, SGMII and HSGMII, while port 7
supports MII, TMII, RMII and RGMII. Use the existing 8365MB-VC jam table
for initialization.
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://patch.msgid.link/3c6d822b-0e85-4173-86ba-2badb140bbf1@yahoo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
net: use IP_OUTNOROUTES drop reason
First patch changes sk_skb_reason_drop() sock to be const.
Second and last patch add SKB_DROP_REASON_IP_OUTNOROUTES
to both tcp_v6_send_response() and inet6_csk_xmit().
====================
Link: https://patch.msgid.link/20260511072310.1094859-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a bare kfree_skb() with a modern sk_skb_reason_drop() call,
and provide IP_OUTNOROUTES drop reason.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260511072310.1094859-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a bare kfree_skb() with a modern sk_skb_reason_drop() call,
and provide IP_OUTNOROUTES drop reason.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260511072310.1094859-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk_skb_reason_drop() does not change sock parameter, make it
const so that we can call it from TCP stack without a cast
on a (const) listener socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260511072310.1094859-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
iproute2 can spend considerable amount of time in ll_init_map()
or ll_link_get() to dump verbose netdev attributes, contributing
to RTNL pressure.
Add RTEXT_FILTER_NAME_ONLY new flag so that rtnl_fill_ifinfo()
limits its output to:
- struct nlmsghdr
- IFLA_IFNAME
- IFLA_PROP_LIST (alternate names)
We can later avoid using RTNL when RTEXT_FILTER_NAME_ONLY
is requested, as none of these attributes need RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260511070244.971028-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
... and PCI device helpers.
The various struct pci_device_id arrays were initialized mostly by one
the PCI_DEVICE macros and then list expressions. The latter isn't easily
readable if you're not into PCI. Using named initializers is more
explicit and thus easier to parse.
Also use PCI_DEVICE* helper macros to assign .vendor, .device,
.subvendor and .subdevice where appropriate and skip explicit
assignments of 0 (which the compiler takes care of).
The secret plan is to make struct pci_device_id::driver_data an
anonymous union (similar to
https://lore.kernel.org/all/cover.1776579304.git.u.kleine-koenig@baylibre.com/)
and that requires named initializers. But it's also a nice cleanup on
its own.
This change doesn't introduce changes to the compiled pci_device_id
arrays. Tested on x86 and arm64.
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Forwarded: id:76da4f44d48bdde84580963862bf9616bee5c9e9.1778149923.git.u.kleine-koenig@baylibre.com (v2)
Reviewed-by: Michael Grzeschik <mgr@kernel.org>
Link: https://patch.msgid.link/20260511090023.1634387-6-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With .class_mask being zero the value of .class doesn't matter because
to check if a pci_device_id entry matches a given device the expression
(id->class ^ dev->class) & id->class_mask
is checked for being zero (see pci_match_one_device()). So drop the
useless and irritating assignment for .class to match what (I think) all
other drivers are doing that don't need to match on .class, i.e. set
both members to zero.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20260511090023.1634387-5-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The default branch in sigd_send() calls sock_put() and returns -EINVAL
without freeing the skb, while all other exit paths do so. Add the
missing dev_kfree_skb() before sock_put() to fix the leak.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Wei Yang <albinwyang@tencent.com>
Link: https://patch.msgid.link/20260509122358.1102997-1-albin_yang@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report PCS receive error counts for all supported PEF 7061, 7071, 7072 and
xRX200 PHYs.
Accumulate the vendor-specific PHY_ERRCNT read-clear counter
(SEL=RXERR) in .update_stats() and expose it as both IEEE 802.3
SymbolErrorDuringCarrier and generic rx_errors via
.get_phy_stats().
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20260509205933.3965832-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phydev->drv can become NULL while the phy_device is still attached to
its net_device, namely after the PHY driver is unbound via sysfs:
echo <mdio_id> > /sys/bus/mdio_bus/drivers/<phy_drv>/unbind
phy_remove() clears phydev->drv but doesn't call phy_detach(), so the
phy_device stays in the link topology xarray and ethnl_req_get_phydev()
still hands it back. ETHTOOL_MSG_PHY_GET then oopses on:
rep_data->drvname = kstrdup(phydev->drv->name, GFP_KERNEL);
drvname is already treated as optional by phy_reply_size(),
phy_fill_reply() and phy_cleanup_data(), so just skip the allocation
when there is no driver bound.
Fixes: 9dd2ad5e92 ("net: ethtool: phy: Convert the PHY_GET command to generic phy dump")
Cc: stable@vger.kernel.org # 6.13.x
Signed-off-by: David Carlier <devnexen@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260509215046.107157-1-devnexen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test was converted from shell script to drv-net test.
The new version is flaky in dbg builds on the netdev.bots dashboard.
The previous shell script had more protections to avoid these. Added
in commit a7ee79b9c4 ("selftests: net: cope with slow env in
so_txtime.sh test").
Add the same overall protection:
- Suppress so_txtime process failure if KSFT_MACHINE_SLOW
Also relax two timeouts to reduce the number of process failures
themselves
- Increase SO_RCVTIMEO to 2 seconds
- Increase process start-up stabilization to 2 seconds
Delays were experimentally arrived at while running with vng
built with kernel/configs/debug.config
Fixes: 5c6baef388 ("selftests: drv-net: convert so_txtime to drv-net")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20260510174219.74aeee6d@kernel.org/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260511222138.2045551-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danilo Krummrich <dakr@kernel.org> says:
When drvdata() was introduced in commit 6f61a2637a ("rust: device: introduce
Device::drvdata()"), its commit message already noted that a direct accessor to
the driver's bus device private data is not commonly required -- bus callbacks
provide access through &self, and other entry points (IRQs, workqueues, IOCTLs,
etc.) carry their own private data.
The sole motivation for drvdata() was inter-driver interaction, e.g. a parent
driver deriving its bus device private data from the child driver via the
auxiliary bus.
However, drvdata() exposes the driver's bus device private data beyond the
driver's own scope. This creates ordering constraints -- drvdata may not be set
yet when the first caller of drvdata() can appear -- and forces the driver's bus
device private data to outlive all registrations that access it; a requirement
that causes unnecessary complications.
Private data should be private to the entity that issues it; bus device private
data belongs to bus callbacks, class device private data to class callbacks, IRQ
private data to the IRQ handler, etc.
This series replaces drvdata() with a dedicated registration_data pointer on
struct auxiliary_device. The parent stores its private data explicitly during
registration; the data is private to the registration and lives as long as the
Registration object.
On teardown, Registration::drop() first triggers auxiliary_device_delete()
(unbinding the child), then frees the registration data. Ordering constraints
are structural -- the child's lifecycle is scoped to the registration by
construction, not by convention.
With no remaining use case for drvdata(), drvdata(), match_type_id(),
set_type_id() and struct driver_type are removed.
This is a prerequisite for [1], which builds on the removal of drvdata() to
enable Higher-Ranked Lifetime Types (HRT) for Rust device drivers.
[1] https://lore.kernel.org/driver-core/20260427221155.2144848-1-dakr@kernel.org/
Link: https://patch.msgid.link/20260505152400.3905096-1-dakr@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>