In GPI mode, the I2C GENI driver programs an extra TX DMA transfer
descriptor (TRE) on the TX channel when handling a single read message.
This results in an unintended write phase being issued on the I2C bus,
even though a read transaction does not require any TX data.
For a single-byte read, the correct hardware sequence consists of the
CONFIG and GO commands followed by a single RX DMA TRE. Programming an
additional TX DMA TRE is redundant, causes unnecessary DMA buffer
mapping on the TX channel, and may lead to incorrect bus behavior.
Update the transfer logic to avoid programming a TX DMA TRE for single
read messages in GPI mode.
Co-developed-by: Maramaina Naresh <naresh.maramaina@oss.qualcomm.com>
Signed-off-by: Maramaina Naresh <naresh.maramaina@oss.qualcomm.com>
Signed-off-by: Aniket Randive <aniket.randive@oss.qualcomm.com>
Reviewed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260410101949.2315058-1-aniket.randive@oss.qualcomm.com
Convert kzalloc_obj + kcalloc to kzalloc_flex to save an allocation.
Add __counted_by to get extra runtime analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260327030310.8502-1-rosenp@gmail.com
This patch introduces I2C PIO functionality for the Spacemit K1 SoC,
enabling the use of I2C in atomic context.
When i2c xfer_atomic is invoked, use_pio is set accordingly.
Since an atomic context is required, all interrupts are disabled when
operating in PIO mode. Even with interrupts disabled, the bits in the
ISR (Interrupt Status Register) will still be set, so error handling can
be performed by polling the relevant status bits in the ISR.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260207-b4-k3-i2c-pio-v7-2-626942d94d91@linux.spacemit.com
The upcoming PIO support requires a wait_pio_xfer() helper, which is
invoked from xfer_msg().
Since wait_pio_xfer() depends on err_check(), move the definition of
xfer_msg() after err_check() to avoid a forward declaration of
err_check().
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260207-b4-k3-i2c-pio-v7-1-626942d94d91@linux.spacemit.com
Currently Linux does not implement ACPI ClockInput() resource to describe
clocks, unlike DT. However the xiic driver is happy if something
magically enables the clock before the driver probes, and does not
turn it off again. The clock should always be considered optional for
ACPI.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260223-i2c-xiic-v12-7-b6c9ce4e4f3c@nexthop.ai
Switch from i2c_add_adapter() to i2c_add_numbered_adapter() to enable
platforms to specify fixed I2C bus numbers via the platform device ID.
This allows systems to maintain consistent bus numbering across reboots.
On platforms where the device ID is PLATFORM_DEVID_NONE (the default),
the adapter falls back to dynamic allocation, preserving backward
compatibility.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260223-i2c-xiic-v12-6-b6c9ce4e4f3c@nexthop.ai
Use standard resource format specifier %pR in debug log.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260223-i2c-xiic-v12-5-b6c9ce4e4f3c@nexthop.ai
Use generic device property accessors making them work for ACPI
platforms.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260223-i2c-xiic-v12-3-b6c9ce4e4f3c@nexthop.ai
The devm_request_threaded_irq() already prints an error message. Remove
the duplicate.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260223-i2c-xiic-v12-2-b6c9ce4e4f3c@nexthop.ai
Add support for the internal I2C controllers of RTL9607C series based
SoCs. Add register definitions, chip-specific functions and macros too.
Make use of the clk introduced from the previous patch to get the clk_div
value and use it during the rtl9607c channel configuration.
Introduce a new EXT_SCK_5MS field to the reg fields struct which is going
to be initialized by rtl9607c init function at the end of the probe.
This patch depends on all the previous patches in this patch series.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-9-adilov@disroot.org
Due to the very nature of differences between RTL9607C i2c controller
and RTL9300 / RTL9310 that are incompatible with each other in some areas
of this driver, for example in clock configuration, channel configuration
and initialization at the end of the probe, introduce new function
properties to the driver data struct to handle those differences.
With these new properties, create configuration functions for RTL9300 and
RTL9310 and assign them to their respective driver data structs.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-8-adilov@disroot.org
In RTL9607C i2c controller, there is 10 bit CLK_DIV field for
setting the clock of i2c interface which depends on the rate
of i2c clk (which seems be fixed to 62.5MHz according to Realtek SDK).
Introduce the clk struct and the respective F_CLK_DIV and clk_div
which are going to be used in the upcoming patch for rtl9607c i2c
controller support addition.
devm_clk_get_optional_enabled() function was used for cleaner code
as it automatically returns NULL if the clk is not present, which is
going to be the case for RTL9300 and RTL9310 i2c controllers.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-7-adilov@disroot.org
Add the "realtek,rtl9607-i2c" compatible for i2c controller on the
RTL9607C SoC series.
Add a clocks property to the properties to describe the i2c reference
clock and make it available for all the compatibles. This i2c reference
clock is assumed to be coming from switchcore region via Lexra bus as
the other SoC peripherals.
According to the info available about the existing devices, they also
have the i2c master controller clocks.
RTL9607C requires the "realtek,scl" and "clocks" to be specified
and so handle it under separate if check for "realtek,rtl9607-i2c".
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-6-adilov@disroot.org
In RTL9607C i2c controller, in order to indicate that the width of
memory address is 8 bits, 0 is written to MEM_ADDR_WIDTH field as
opposed to 1 for RTL9300 and RTL9310.
Introduce a new property to a driver data to indicate what value
need to written to MEM_ADDR_WIDTH field for this case.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-5-adilov@disroot.org
In RTL9607C i2c controller the busy check operation is done on the
separate bit of the command register as opposed to self clearing
command trigger bit on the rtl9300 and rtl9310 i2c controllers.
Introduce a new F_BUSY field to the reg_fields struct for that
and change the regmap read poll function to use F_BUSY
instead of I2C_TRIG.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-4-adilov@disroot.org
In RTL9607C i2c controller, theoretical maximum the data length
can be is 4 bytes as opposed to 16 bytes on rtl9300 and rtl9310.
Introduce a new property to the driver data struct for that.
Adjust if statement in prepare_xfer function to follow that new
property instead of the hardcoded value.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-3-adilov@disroot.org
In RTL9607C i2c controller, there are 2 separate registers for reads
and writes as opposed the combined 1 on rtl9300 and rtl9310.
In preparation for RTL9607C support, split it up into rd_reg and wd_reg
properties and change the i2c read and write functions accordingly.
Signed-off-by: Rustam Adilov <adilov@disroot.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260401180648.337834-2-adilov@disroot.org
Some SFP modules on certain switches (for example the ONTi ONT-S508CL-8S and
XikeStor SKS8300-8X) exhibit unreliable I2C communication at the currently
supported speeds. Add support for 50 kHz and 2.5 MHz I2C bus modes on the
RTL9300 to improve compatibility with these devices.
Signed-off-by: Jan Kantert <jan-kernel@kantert.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260227111134.2163701-1-jan-kernel@kantert.net
Convert the IOP3xx and IXP4xx XScale bindings to DT schema. This
conversion also adds the interrupts property, as it is used by the driver
and existing DTS files but was not documented in the original binding.
Signed-off-by: Shi Hao <i.shihao.999@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260330054439.9545-1-i.shihao.999@gmail.com
Replace the manual polling loop in ocores_wait() with the kernel helper
read_poll_timeout_atomic(). This simplifies the code and ensures robust
timeout handling.
In particular, the helper guarantees a condition check after the
delay, even if the delay exceeds the timeout, avoiding spurious
timeout errors under load or preemption.
Signed-off-by: Martin Aberer <martin.aberer@bachmann.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324140556.2249039-1-martin.aberer@bachmann.info
Trivial change, a never used macro CCI_RES_MAX can be removed from
the CCI driver.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260326165345.762807-1-vladimir.zapolskiy@linaro.org
Define a new ACPI HID for GOOG5000 as used on Google Axion.
This has been validated on Silicon.
Signed-off-by: Moritz Fischer <moritzf@google.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260326200451.2904375-1-moritzf@google.com
Add support for the Tegra410 SoC, which has 4 I2C controllers. The
controllers are feature-equivalent to Tegra264; only the register
offsets differ.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-4-kkartik@nvidia.com
Tegra410 use different offsets for existing I2C registers, update
the logic to use appropriate offsets per SoC.
As the register offsets are now defined in the SoC-specific
tegra_i2c_regs structures, the tegra_i2c_reg_addr() function is no
longer needed to translate register offsets and has been removed.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-3-kkartik@nvidia.com
Replace the per-instance DVC/VI boolean flags with a tegra_i2c_variant
enum and move the variant field into tegra_i2c_hw_feature so it is
populated via SoC match data.
Add dedicated SoC data entries for the "nvidia,tegra20-i2c-dvc" and
"nvidia,tegra210-i2c-vi" compatibles and drop compatible-string checks
from tegra_i2c_parse_dt.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-2-kkartik@nvidia.com
Add a compatible string for the I2C controller found in SpacemiT K3 SoC
which use same I2C IP as K1, so make it fallback to K1 compatible.
Signed-off-by: Yixun Lan <dlan@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://lore.kernel.org/r/20260325-02-k3-i2c-v1-1-78f29c83d9ac@kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The first byte of an i2c SMBUS message is the size, and it should be
verified to ensure that it is in the range of 0..I2C_SMBUS_BLOCK_MAX
before processing it.
This is the same logic that was added in commit a6e04f05ce ("i2c:
tegra: check msg length in SMBUS block read") to the i2c tegra driver.
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Andi Shyti <andi.shyti@kernel.org>
Cc: stable <stable@kernel.org>
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/2026022314-rely-scrubbed-4839@gregkh
As stated in the d70f60ad96 ("i2c: designware: Remove
not-going-to-be-supported code for Baikal SoC") the Baikal
platforms are not supported and the respective driver code
was removed. Remove the currently unused bindings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260224115210.3499191-1-andriy.shevchenko@linux.intel.com
Pointers should use NULL instead of explicit '0', as pointed out by
sparse:
i2c-npcm7xx.c:1387:61: warning: Using plain integer as NULL pointer
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260216085825.70568-2-krzysztof.kozlowski@oss.qualcomm.com
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtg+xQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKwQ+AQCiXEYAibl3vHRgQo7qEPCC5or4FtkF
HZ0ERRArhsU17AD/TKHE/AJkyFrwK4rGTb6I9Wi1OXnpG7jihZlYjj03Ag4=
=CUql
-----END PGP SIGNATURE-----
Merge tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux
Pull fsverity fixes from Eric Biggers:
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux:
fsverity: fix build error by adding fsverity_readahead() stub
fsverity: remove fsverity_verify_page()
f2fs: make f2fs_verify_cluster() partially large-folio-aware
f2fs: remove unnecessary ClearPageUptodate in f2fs_verify_cluster()
Fix a big endian specific issue in the PPC64-optimized AES code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtiphQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOK/z2AQD1j15Ao3iDW3yBSyTS+tFJaRUVDtjg
bNostoNJAjMM9wD/X0oAnt95WTNkdHexs+2aMzQ4ULKFRcwQrUTarKx7IgY=
=Dmfx
-----END PGP SIGNATURE-----
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix a big endian specific issue in the PPC64-optimized AES code"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: powerpc/aes: Fix rndkey_from_vsx() on big endian CPUs
Stephen retired and stepped back from -next maintainership, update his
entry in CREDITS to recognise his 18 years of hard work making it what
it is today and all the impact it's had on our development process.
Also update to his current GnuPG key while we're here.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x509 public key code gained a dependency on the sha256 hash
implementation, causing a rare link time failure in randconfig
builds:
arm-linux-gnueabi-ld: crypto/asymmetric_keys/x509_public_key.o: in function `x509_get_sig_params':
x509_public_key.c:(.text.x509_get_sig_params+0x12): undefined reference to `sha256'
arm-linux-gnueabi-ld: (sha256): Unknown destination type (ARM/Thumb) in crypto/asymmetric_keys/x509_public_key.o
x509_public_key.c:(.text.x509_get_sig_params+0x12): dangerous relocation: unsupported relocation
Select the necessary library code from Kconfig.
Fixes: 2c62068ac8 ("x509: Separately calculate sha256 for blacklist")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align to the commit bf4afc53b7 ("Convert 'alloc_obj' family to use the
new default GFP_KERNEL argument") update the 'kmalloc_obj' declaration
for userspace to fix below compile error:
In file included from arch/arm/boot/compressed/../../../../lib/decompress_unxz.c:241,
from arch/arm/boot/compressed/decompress.c:56:
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'xz_dec_init':
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c:787:28: error: implicit declaration of function 'kmalloc_obj'; did you mean 'kmalloc'? [-Wimplicit-function-declaration]
787 | struct xz_dec *s = kmalloc_obj(*s);
| ^~~~~~~~~~~
| kmalloc
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Fixes: bf4afc53b7 ("Convert 'alloc_obj' family to use the new default GFP_KERNEL argument")
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toolchain and infrastructure:
- Pass '-Zunstable-options' flag required by the future Rust 1.95.0.
- Fix 'objtool' warning for Rust 1.84.0.
'kernel' crate:
- 'irq' module: add missing bound detected by the future Rust 1.95.0.
- 'list' module: add missing 'unsafe' blocks and placeholder safety
comments to macros (an issue for future callers within the crate).
'pin-init' crate:
- Clean Clippy warning that changed behavior in the future Rust 1.95.0.
-----BEGIN PGP SIGNATURE-----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=DOG1
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Pass '-Zunstable-options' flag required by the future Rust 1.95.0
- Fix 'objtool' warning for Rust 1.84.0
'kernel' crate:
- 'irq' module: add missing bound detected by the future Rust 1.95.0
- 'list' module: add missing 'unsafe' blocks and placeholder safety
comments to macros (an issue for future callers within the crate)
'pin-init' crate:
- Clean Clippy warning that changed behavior in the future Rust
1.95.0"
* tag 'rust-fixes-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: list: Add unsafe blocks for container_of and safety comments
rust: pin-init: replace clippy `expect` with `allow`
rust: irq: add `'static` bounds to irq callbacks
objtool/rust: add one more `noreturn` Rust function
rust: kbuild: pass `-Zunstable-options` for Rust 1.95.0
Summary of changes:
- Fix multiple definition of __pcpu_unique_da_mon_this
After refactoring monitors, we used static per-cpu variables with the
same names across different per-cpu monitors. This is explicitly
disallowed for modules on some architectures (alpha) or if
CONFIG_DEBUG_FORCE_WEAK_PER_CPU is enabled (e.g. Fedora's debug
kernel). Make sure all those variables have different names to avoid
compilation issues.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaZoJ1BQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qkykAP41lj9VAe0dM81f20IfOBhqIBZPS6MP
ajRGZ9bz1ZiJwwD/dHm+APheD7umImzoDXpW1IJxgNPlZTnpte3WyhIYaQs=
=HxRz
-----END PGP SIGNATURE-----
Merge tag 'trace-rv-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull runtime verifier fix from Steven Rostedt:
- Fix multiple definition of __pcpu_unique_da_mon_this
After refactoring monitors, we used static per-cpu variables with the
same names across different per-cpu monitors. This is explicitly
disallowed for modules on some architectures (alpha) or if
CONFIG_DEBUG_FORCE_WEAK_PER_CPU is enabled (e.g. Fedora's debug
kernel). Make sure all those variables have different names to avoid
compilation issues.
* tag 'trace-rv-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rv: Fix multiple definition of __pcpu_unique_da_mon_this
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most simple allocations use GFP_KERNEL, and with the new allocation
helpers being introduced, let's just take advantage of that to simplify
that default case.
It's a numbers game:
git grep 'alloc_obj(' |
sed 's/.*\(GFP_[_A-Z]*\).*/\1/' |
sort | uniq -c | sort -n | tail
shows that about 90% of all those new allocator instances just use that
standard GFP_KERNEL.
Those helpers are already macros, and we can easily just make it be the
default case when the gfp argument is missing.
And yes, we could do that for all the legacy interfaces too, but let's
keep it to just the new ones at least for now, since those all got
converted recently anyway, so this is not any "extra" noise outside of
that limited conversion.
And, in fact, I want to do this before doing the -rc1 release, exactly
so that we don't get extra merge conflicts.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for
non-scalar types") started using the new allocation helpers, and in the
process showed that they were completely non-working.
The overflow logic in overflows_flex_counter_type() is completely the
wrong way around, and that broke __alloc_flex() completely. By chance,
the resulting code was then such a mess that clang generated
sufficiently garbage code that objtool warned about it all. Which made
it somewhat quicker to narrow things down.
While fixing overflows_flex_counter_type() would presumably fix this
all, I'm excising the whole broken overflow logic from __alloc_flex(),
because we don't want that kind of code in basic allocation functions
anyway.
That (no longer) broken overflows_flex_counter_type() thing needs to be
inserted into the actual __set_flex_counter() logic in the unlikely case
that we ever want this at all. And made conditional.
Fixes: 81cee9166a ("compiler_types: Introduce __flex_counter() and family")
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Cc: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/all/CAHk-=whEd020BYzGTzYrENjD9Z5_82xx6h8HsQvH5xDSnv0=Hw@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRSPkdeREjth1dHnSE2KwveOeQkuwUCaZl14wAKCRA2KwveOeQk
uz8aAQCBFLYlij3Y3ivVADkBxuVF3xECaznFya41ENYsBwlHdwEArXqMyNrw+DiG
TvWCK/tiddNmGIRpI2sxBFzyRpsHfAY=
=rVD3
-----END PGP SIGNATURE-----
Merge tag 'kmalloc_obj-treewide-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kmalloc_obj conversion from Kees Cook:
"This does the tree-wide conversion to kmalloc_obj() and friends using
coccinelle, with a subsequent small manual cleanup of whitespace
alignment that coccinelle does not handle.
This uncovered a clang bug in __builtin_counted_by_ref(), so the
conversion is preceded by disabling that for current versions of
clang. The imminent clang 22.1 release has the fix.
I've done allmodconfig build tests for x86_64, arm64, i386, and arm. I
did defconfig builds for alpha, m68k, mips, parisc, powerpc, riscv,
s390, sparc, sh, arc, csky, xtensa, hexagon, and openrisc"
* tag 'kmalloc_obj-treewide-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kmalloc_obj: Clean up after treewide replacements
treewide: Replace kmalloc with kmalloc_obj for non-scalar types
compiler_types: Disable __builtin_counted_by_ref for Clang
- Introduce 'perf sched stats' tool with record/report/diff workflows
using schedstat counters.
- Add a faster libdw based addr2line implementation and allow selecting
it or its alternatives via 'perf config addr2line.style='.
- Data-type profiling fixes and improvements including the ability
to select fields using 'perf report''s -F/-fields, e.g.:
'perf report --fields overhead,type'
- Add 'perf test' regression tests for Data-type profiling with
C and Rust workloads.
- Fix srcline printing with inlines in callchains, make sure this has
coverage in 'perf test'.
- Fix printing of leaf IP in LBR callchains.
- Fix display of metrics without sufficient permission in 'perf stat'.
- Print all machines in 'perf kvm report -vvv', not just the host.
- Switch from SHA-1 to BLAKE2s for build ID generation, remove SHA-1
code.
- Fix 'perf report's histogram entry collapsing with '-F' option.
- Use system's cacheline size instead of a hardcoded value in 'perf
report'.
- Allow filtering conversion by time range in 'perf data'.
- Cover conversion to CTF using 'perf data' in 'perf test'.
- Address newer glibc const-correctness (-Werror=discarded-qualifiers)
issues.
- Fixes and improvements for ARM's CoreSight support, simplify ARM SPE
event config in 'perf mem', update docs for 'perf c2c' including the
ARM events it can be used with.
- Build support for generating metrics from arch specific python script,
add extra AMD, Intel, ARM64 metrics using it.
- Add AMD Zen 6 events and metrics.
- Add JSON file with OpenHW Risc-V CVA6 hardware counters.
- Add 'perf kvm' stats live testing.
- Add more 'perf stat' tests to 'perf test'.
- Fix segfault in `perf lock contention -b/--use-bpf`
- Fix various 'perf test' cases for s390.
- Build system cleanups, bump minimum shellcheck version to 0.7.2
- Support building the capstone based annotation routines as a plugin.
- Allow passing extra Clang flags via EXTRA_BPF_FLAGS.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCaZn25QAKCRCyPKLppCJ+
J9MbAQCTKChBwDsqVh5iPr0UAc+mez9LOPJFa580SYH9nmd1jgD+Oqip7xCf514G
ZtYPNh+Mz0se0Mcb++syLUEjxvbrQQY=
=y2VY
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v7.0-1-2026-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools updates from Arnaldo Carvalho de Melo:
- Introduce 'perf sched stats' tool with record/report/diff workflows
using schedstat counters
- Add a faster libdw based addr2line implementation and allow selecting
it or its alternatives via 'perf config addr2line.style='
- Data-type profiling fixes and improvements including the ability to
select fields using 'perf report''s -F/-fields, e.g.:
'perf report --fields overhead,type'
- Add 'perf test' regression tests for Data-type profiling with C and
Rust workloads
- Fix srcline printing with inlines in callchains, make sure this has
coverage in 'perf test'
- Fix printing of leaf IP in LBR callchains
- Fix display of metrics without sufficient permission in 'perf stat'
- Print all machines in 'perf kvm report -vvv', not just the host
- Switch from SHA-1 to BLAKE2s for build ID generation, remove SHA-1
code
- Fix 'perf report's histogram entry collapsing with '-F' option
- Use system's cacheline size instead of a hardcoded value in 'perf
report'
- Allow filtering conversion by time range in 'perf data'
- Cover conversion to CTF using 'perf data' in 'perf test'
- Address newer glibc const-correctness (-Werror=discarded-qualifiers)
issues
- Fixes and improvements for ARM's CoreSight support, simplify ARM SPE
event config in 'perf mem', update docs for 'perf c2c' including the
ARM events it can be used with
- Build support for generating metrics from arch specific python
script, add extra AMD, Intel, ARM64 metrics using it
- Add AMD Zen 6 events and metrics
- Add JSON file with OpenHW Risc-V CVA6 hardware counters
- Add 'perf kvm' stats live testing
- Add more 'perf stat' tests to 'perf test'
- Fix segfault in `perf lock contention -b/--use-bpf`
- Fix various 'perf test' cases for s390
- Build system cleanups, bump minimum shellcheck version to 0.7.2
- Support building the capstone based annotation routines as a plugin
- Allow passing extra Clang flags via EXTRA_BPF_FLAGS
* tag 'perf-tools-for-v7.0-1-2026-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: (255 commits)
perf test script: Add python script testing support
perf test script: Add perl script testing support
perf script: Allow the generated script to be a path
perf test: perf data --to-ctf testing
perf test: Test pipe mode with data conversion --to-json
perf json: Pipe mode --to-ctf support
perf json: Pipe mode --to-json support
perf check: Add libbabeltrace to the listed features
perf build: Allow passing extra Clang flags via EXTRA_BPF_FLAGS
perf test data_type_profiling.sh: Skip just the Rust tests if code_with_type workload is missing
tools build: Fix feature test for rust compiler
perf libunwind: Fix calls to thread__e_machine()
perf stat: Add no-affinity flag
perf evlist: Reduce affinity use and move into iterator, fix no affinity
perf evlist: Missing TPEBS close in evlist__close()
perf evlist: Special map propagation for tool events that read on 1 CPU
perf stat-shadow: In prepare_metric fix guard on reading NULL perf_stat_evsel
Revert "perf tool_pmu: More accurately set the cpus for tool events"
tools build: Emit dependencies file for test-rust.bin
tools build: Make test-rust.bin be removed by the 'clean' target
...
This patch series, from Benjamin Philip <benjamin.philip495@gmail.com>,
simplifies and clarifies the handling of output generated by Coccinelle
that is sent to standard error. By default, this information goes to
/dev/null. The patch series reminds the user of that and encourages
them to provide another file name.
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
-----BEGIN PGP SIGNATURE-----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=+f+s
-----END PGP SIGNATURE-----
Merge tag 'cocci-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"This simplifies and clarifies the handling of output generated by
Coccinelle that is sent to standard error.
By default, this goes to /dev/null. Remind the user of that and
encourage them to provide another file name (Benjamin Philip)"
* tag 'cocci-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
Documentation: Coccinelle: document debug log handling
scripts: coccicheck: warn on unset debug file
scripts: coccicheck: simplify debug file handling
cleanups, and new hardware support. ntb_transport QP stats are
converted to seq_file, a tx_memcpy_offload module parameter is
introduced with associated ordering fixes, and a debugfs queue
name truncation bug is corrected. Additional fixes address format
specifier mismatches in ntb_tool and boundary conditions in the
Switchtec driver, while unused MSI helpers are removed and the
codebase migrates to dma_map_phys(). Intel Gen6 (Diamond Rapids)
NTB support is also added.
-----BEGIN PGP SIGNATURE-----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=UZw9
-----END PGP SIGNATURE-----
Merge tag 'ntb-7.0' of https://github.com/jonmason/ntb
Pull NTB (PCIe non-transparent bridge) updates from Jon Mason:
"NTB updates include debugfs improvements, correctness fixes, cleanups,
and new hardware support:
ntb_transport QP stats are converted to seq_file, a tx_memcpy_offload
module parameter is introduced with associated ordering fixes, and a
debugfs queue name truncation bug is corrected.
Additional fixes address format specifier mismatches in ntb_tool and
boundary conditions in the Switchtec driver, while unused MSI helpers
are removed and the codebase migrates to dma_map_phys().
Intel Gen6 (Diamond Rapids) NTB support is also added"
* tag 'ntb-7.0' of https://github.com/jonmason/ntb:
NTB: ntb_transport: Use seq_file for QP stats debugfs
NTB: ntb_transport: Fix too small buffer for debugfs_name
ntb/ntb_tool: correct sscanf format for u64 and size_t in tool_peer_mw_trans_write
ntb: intel: Add Intel Gen6 NTB support for DiamondRapids
NTB/msi: Remove unused functions
ntb: ntb_hw_switchtec: Increase MAX_MWS limit to 256
ntb: ntb_hw_switchtec: Fix array-index-out-of-bounds access
ntb: ntb_hw_switchtec: Fix shift-out-of-bounds for 0 mw lut
NTB: epf: allow built-in build
ntb: migrate to dma_map_phys instead of map_page
NTB: ntb_transport: Add 'tx_memcpy_offload' module option
NTB: ntb_transport: Remove unused 'retries' field from ntb_queue_entry
