Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs are
not practical. Use newly introduced aliases for mmcblk devices from [1].
The sort order is based on reg address.
[1] https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210118155242.7172-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The datasheet of the PCF2127 states, it is recommended to process an OTP
refresh once the power is up and the oscillator is operating stable. The
OTP refresh takes less than 100 ms to complete.
Signed-off-by: Philipp Rosenberger <p.rosenberger@kunbus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118085752.5759-3-p.rosenberger@kunbus.com
Pull crypto fix from Herbert Xu:
"Fix a regression in the cesa driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvel/cesa - Fix tdma descriptor on 64-bit
To resume normal operation after a total power loss (no or empty
battery) the "Power-On Reset Override (PORO)" facility needs to be
disabled.
The register reset value sets the PORO enabled and the data sheet
recommends setting it to disabled for normal operation.
From what I've seen on the PCF2127 and PCF2129 there is no event
generated at the interrupt pin (INT), as long the PORO bit is set. This
behavior is not documented in the manual.
Signed-off-by: Philipp Rosenberger <p.rosenberger@kunbus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118085752.5759-2-p.rosenberger@kunbus.com
When working on the PCI VPD code I also tested with a Broadcom BCM95719
card. tg3 uses internal NVRAM access with this card, so I forced it to
PCI VPD mode for testing. PCI VPD access fails
(i + PCI_VPD_LRDT_TAG_SIZE + j > len) because only TG3_NVM_VPD_LEN (256)
bytes are read, but PCI VPD has 400 bytes on this card.
So add a constant TG3_NVM_PCI_VPD_MAX_LEN that defines the maximum
PCI VPD size. The actual VPD size is returned by pci_read_vpd().
In addition it's not worth looping over pci_read_vpd(). If we miss the
125ms timeout per VPD dword read then definitely something is wrong,
and if the tg3 module loading is killed then there's also not much
benefit in retrying the VPD read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/cb9e9113-0861-3904-87e0-d4c4ab3c8860@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'name' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'parent_names' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'num_parents' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'base' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'muxdiv_offset' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_width' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_width' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_offset' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'lock' not described in 'rockchip_clk_register_halfdiv'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-5-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-pll.c:104: warning: Function parameter or member 'i' not described in 'RK3036_PLLCON'
drivers/clk/rockchip/clk-pll.c:365: warning: Function parameter or member 'nr' not described in 'RK3066_PLL_RESET_DELAY'
drivers/clk/rockchip/clk-pll.c:584: warning: Function parameter or member 'i' not described in 'RK3399_PLLCON'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-4-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-cpu.c:65: warning: Function parameter or member 'cpu_mux' not described in 'rockchip_cpuclk'
drivers/clk/rockchip/clk-cpu.c:65: warning: Function parameter or member 'cpu_mux_ops' not described in 'rockchip_cpuclk'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-3-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'name' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'parent_names' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'num_parents' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'base' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'muxdiv_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_width' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_width' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_table' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'lock' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'hw' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'rate' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'parent_rate' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'm' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'n' not described in 'rockchip_fractional_approximation'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-2-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With vrr enabled the hardware no longer latches the registers
automagically at vblank start. The point at which it will do the
latching even when no push has been sent is the vmax decision
boundary. That is the thing we need to evade to avoid our
register latching to get split between two frames.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-18-manasi.d.navare@intel.com
To get sensible vblank timestamping behaviour we need to feed
the vmax based timings to the vblank code, otherwise it'll chop
off the scanline counter when it exceeds the minumum vtotal.
Additionally with VRR we have three cases to consider when we
generate the vblank timestamp:
1) we are in vertical active
-> nothing special needs to be done, just return the current
scanout position and the core will calculate the timestamp
corresponding to the past time when the current vertical
active started
2) we are in vertical blank and no push has been sent
-> the hardware will keep extending the vblank presumably
to its maximum length, so we make the timestmap match the
expected time when the max length vblank will end. Since
the timings used for this are now based on vmax nothing
special actually needs to be done
3) we are in vblank and a push has been sent so the vblank is
about to terminate
-> presumably we want the timestmap to accurately reflect
when the vblank will terminate, so we use the sampled
frame timestamp vs. current timestamp to guesstimate
how far along the vblank exit we are, and then we
adjust the reported scanout position accordingly so
that the core will see that the vblank is close to
ending.
v2:
* Fix the else if (use_scanline_Counter) (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-17-manasi.d.navare@intel.com
With VRR the earliest the registers can get latched are at
flipline decision boundary, calculate that as vrr_vmin_vblank_start()
and the latest the regsiters can get latched are vmax decision boundary
calculate that as vrr_vmax_vblank_start()
v2:
* Remove TODO and adjust extra scanline const (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-15-manasi.d.navare@intel.com
This functions gets the VRR config from the VRR registers
to match the crtc state variables for VRR.
v2:
* Rebase (Manasi)
* Use HAS_VRR (Jani N)
v3:
* Get pipeline_full, flipline (Ville)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-14-manasi.d.navare@intel.com
If VRR is enabled, the sink should ignore MSA parameters
and regenerate incoming video stream without depending
on these parameters. Hence set the MSA_TIMING_PAR_IGNORE_EN
bit if VRR is enabled.
Reset this bit on VRR disable.
v2:
* ACtually set the dpcd msa ignore bit (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-13-manasi.d.navare@intel.com
This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.
Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.
v2:
* Use intel_de_rmw (Jani N)
v3:
* Remove rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-12-manasi.d.navare@intel.com
VRR achieves vblank stretching using the HW PUSH functionality.
So once the VRR is enabled during modeset then for each flip
request from userspace, in the atomic tail pipe_update_end()
we need to set the VRR push bit in HW for it to terminate
the vblank at configured flipline or anytime after flipline
or latest at the Vmax.
The HW clears the PUSH bit after the double buffer updates
are completed.
v2:
* Move send push to after irq en (Manasi)
* Call send push unconditionally (Jani N)
v3:
* Stall w.r.t Vrr vmax (Manasi, Gary Smith)
v4:
* Remove the rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gary Smith <gary.k.smith@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-11-manasi.d.navare@intel.com
This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.
v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)
v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-10-manasi.d.navare@intel.com
Even though our HW supports PSR + VRR, the available panels
do not work reliably with PSR and VRR together. So if user
requested VRR and is supported by HW enable that and do not
enable PSR in that case.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-7-manasi.d.navare@intel.com
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com
We want to calculate the vblank_start for vblank evasion
differently for vrr. To make that nicer lets first extract
the current non-vrr case to a helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-4-manasi.d.navare@intel.com
The vrr calculations will need to know the framestart delay value
we use. Currently we program it always to zero, but should that change
we probably want to stash it somewhere.
Could stick it into the crtc_state I suppose, but since we never
change it let's just stuff it into dev_priv for now.
v2:
* Rebase on drm-tip (Manasi)
v3:
* Framestart_delay as 1 - 4 to align with HW
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-3-manasi.d.navare@intel.com
This function sets the VRR property for connector based
on the platform support, EDID monitor range and DP sink
DPCD capability of outputing video without msa
timing information.
v8:
* Use HAS_VRR, remove drm_conn declaration (Jani N)
* Fix typos in Comment (Jani N)
v7:
* Move the helper to separate file (Manasi)
v6:
* Remove unset of prop
v5:
* Fix the vrr prop not being set in kernel (Manasi)
* Unset the prop on connector disconnect (Manasi)
v4:
* Rebase (Mansi)
v3:
* intel_dp_is_vrr_capable can be used for debugfs, make it
non static (Manasi)
v2:
* Just set this in intel_dp_get_modes instead of new hook (Jani)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-2-manasi.d.navare@intel.com
There exists many build warnings when make M=samples/bpf on the Loongson
platform, this issue is MIPS related, x86 compiles just fine.
Here are some warnings:
CC samples/bpf/ibumad_user.o
samples/bpf/ibumad_user.c: In function ‘dump_counts’:
samples/bpf/ibumad_user.c:46:24: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf("0x%02x : %llu\n", key, value);
~~~^ ~~~~~
%lu
CC samples/bpf/offwaketime_user.o
samples/bpf/offwaketime_user.c: In function ‘print_ksym’:
samples/bpf/offwaketime_user.c:34:17: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf("%s/%llx;", sym->name, addr);
~~~^ ~~~~
%lx
samples/bpf/offwaketime_user.c: In function ‘print_stack’:
samples/bpf/offwaketime_user.c:68:17: warning: format ‘%lld’ expects argument of type ‘long long int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf(";%s %lld\n", key->waker, count);
~~~^ ~~~~~
%ld
MIPS needs __SANE_USERSPACE_TYPES__ before <linux/types.h> to select
'int-ll64.h' in arch/mips/include/uapi/asm/types.h, then it can avoid
build warnings when printing __u64 with %llu, %llx or %lld.
The header tools/include/linux/types.h defines __SANE_USERSPACE_TYPES__,
it seems that we can include <linux/types.h> in the source files which
have build warnings, but it has no effect due to actually it includes
usr/include/linux/types.h instead of tools/include/linux/types.h, the
problem is that "usr/include" is preferred first than "tools/include"
in samples/bpf/Makefile, that sounds like a ugly hack to -Itools/include
before -Iusr/include.
So define __SANE_USERSPACE_TYPES__ for MIPS in samples/bpf/Makefile
is proper, if add "TPROGS_CFLAGS += -D__SANE_USERSPACE_TYPES__" in
samples/bpf/Makefile, it appears the following error:
Auto-detecting system features:
... libelf: [ on ]
... zlib: [ on ]
... bpf: [ OFF ]
BPF API too old
make[3]: *** [Makefile:293: bpfdep] Error 1
make[2]: *** [Makefile:156: all] Error 2
With #ifndef __SANE_USERSPACE_TYPES__ in tools/include/linux/types.h,
the above error has gone and this ifndef change does not hurt other
compilations.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/1611551146-14052-1-git-send-email-yangtiezhu@loongson.cn
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful
purpose, and certainly bear no relation at all to the actual underlying
interconnect topology. They appear to be cargo-cult copying from a
design misstep in the very early days of FDT adoption on ARM, which was
righted with the "arm,primecell" compatible, and the last trace of the
idea finally purged by commit 2ef7d5f342 ("ARM, ARM64: dts: drop
"arm,amba-bus" in favor of "simple-bus"").
As such, they can simply be removed and the DMA-330 nodes fitted into
the normal sort order.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/e682edd25133bde2ed8198138febc90071530a51.1611186142.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update struct bpf_perf_event_data with the addr field to match the
tools headers with the kernel headers.
Signed-off-by: Florian Lehner <dev@der-flo.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210123185221.23946-1-dev@der-flo.net
Following RFC 6554 [1], the current order of fields is wrong for big
endian definition. Indeed, here is how the header looks like:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This patch reorders fields so that big endian definition is now correct.
[1] https://tools.ietf.org/html/rfc6554#section-3
Fixes: cfa933d938 ("include: uapi: linux: add rpl sr header definition")
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missed 'ranges' and 'dma-coherent' properties as cdns-usb DT nodes has
child node and DMA IO is coherent on TI K3 J721E/J7200 SoCs.
This also fixes dtbs_check warning:
cdns-usb@4104000: 'dma-coherent', 'ranges' do not match any of the regexes: '^usb@', 'pinctrl-[0-9]+'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210115193124.5706-1-grygorii.strashko@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
NanoPi R2S is headless, so rightly does not enable any of the display
interface hardware, which currently provokes an obnoxious error in the
boot log from the fake DRM device failing to find anything to bind to.
It probably isn't *too* hard to obviate the fake device shenanigans
entirely with a bit of driver reshuffling, but for now let's just
disable it here to shut up the spurious error.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/c4553dfad1ad6792c4f22454c135ff55de77e2d6.1611186099.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let us use a local variable in nsswitchthread(), so we can remove a
lot of casting for better readability.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210122154725.22140-7-bjorn.topel@gmail.com
Instead of passing void * all over the place, let us pass the actual
type (ifobject) and remove the void-ptr-to-type-ptr casting.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210122154725.22140-2-bjorn.topel@gmail.com
We create a new file for all VRR related helpers.
Also add a function to check vrr capability based on
platform support, DPCD bits and EDID monitor range.
v2:
* Remove author (Jani N)
* Define HAS_VRR (Jani N)
* Ensure intel_dp can be obtained from conn (Jani N)
v3:
* Fix the header indent (Manasi)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125200818.2015-1-manasi.d.navare@intel.com
The NanoPi M4B is a minor revision of the original M4.
The differences against the original Nanopi M4 that are common with the
other M4V2 revision include:
- microphone header removed
- power button added
- recovery button added
Additional changes specific to the M4B:
- USB 3.0 hub removed; board now has 2x USB 3.0 type-A ports and 2x
USB 2.0 ports
- ADB toggle switch added; this changes the top USB 3.0 host port to
a peripheral port
- Type-C port no longer supports data or PD
- WiFi/Bluetooth combo chip switched to AP6256, which supports BT 5.0
but only 1T1R (down from 2T2R) for WiFi
Add a new dts file for the new board revision that shows the difference
against the original.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-5-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only the NanoPC T4 hs the PCIe reset pin routed to the SoC. For the
NanoPi M4 family, no such signal is routed to the expansion header on
the base board.
As the schematics for the expansion board were not released, it is
unclear how this is handled, but the likely answer is that the signal
is always pulled high.
Move the ep-gpios property from the common nanopi4.dtsi file to the
board level nanopc-t4.dts file. This makes the nanopi-m4 lack ep-gpios,
matching the board design.
A companion patch "PCI: rockchip: make ep_gpio optional" for the Linux
driver is required, as the driver currently requires the property to be
present.
Fixes: e7a0959082 ("arm64: dts: rockchip: Add devicetree for NanoPC-T4")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add detection for kernel version, and adapt the BPF program based on
kernel support. This way, users will get the best possible performance
from the BPF program.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210122105351.11751-4-bjorn.topel@gmail.com
TPS65910 is a PMIC MFD device and RTC is one of its functions. The
wakeup-source DT property is specified for the parent MFD device and we
need to use this property for the RTC in order to allow to use RTC alarm
for waking up system from suspend by default, instead of requiring user
to enable wakeup manually via sysfs.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210120211603.18555-1-digetx@gmail.com
Fold xp_assign_dev and __xp_assign_dev. The former directly calls the
latter.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210122105351.11751-3-bjorn.topel@gmail.com