'struct uac_req' purpose is to link 'struct usb_request' to the
corresponding 'struct uac_rtd_params'. However member req is never
used. Using the context of the usb request, we can keep track of the
corresponding 'struct uac_rtd_params' just as well, without allocating
extra memory.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-4-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factorize format related code common to the capture and playback path.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-3-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the kernel doc for usb_ep_dequeue(), it states that "this
routine is asynchronous, that is, it may return before the completion
routine runs". And indeed since v5.0 the dwc3 gadget driver updated
its behavior to place dequeued requests on to a cancelled list to be
given back later after the endpoint is stopped.
The free_ep() was incorrectly assuming that a request was ready to
be freed after calling dequeue which results in a use-after-free
in dwc3 when it traverses its cancelled list. Fix this by moving
the usb_ep_free_request() call to the callback itself in case the
ep is disabled.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Reported-and-tested-by: Ferry Toth <fntoth@gmail.com>
Reviewed-and-tested-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a gadget supports SuperSpeed Plus, then it may operate in different
sublink speeds. For example, if the gadget supports SuperSpeed Plus
gen2x2, then it can support 2 sublink speeds gen1 and gen2. Inform the
host of these speeds in the BOS descriptor.
Use 1 SSID if the gadget supports up to gen2x1, or not specified:
- SSID 0 for symmetric RX/TX sublink speed of 10 Gbps.
Use 1 SSID if the gadget supports up to gen1x2:
- SSID 0 for symmetric RX/TX sublink speed of 5 Gbps.
Use 2 SSIDs if the gadget supports up to gen2x2:
- SSID 0 for symmetric RX/TX sublink speed of 5 Gbps.
- SSID 1 for symmetric RX/TX sublink speed of 10 Gbps.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/eb0386fdd5d87a858281e8006a72723d3732240f.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeed Plus device may operate at different speed and lane count
(i.e. gen2x2, gen1x2, or gen2x1). Introduce gadget ops
udc_set_ssp_rate() to set the desire corresponding usb_ssp_rate for
SuperSpeed Plus capable devices.
If the USB device supports different speeds at SuperSpeed Plus, set the
device to operate with the maximum number of lanes and speed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9b85357cdadc02e3f0d653fd05f89eb46af836e1.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB device controller operating in SuperSpeed Plus may support gen2x1,
gen1x2, and/or gen2x2. Introduce SuperSpeed Plus signaling rate
generation and lane count to usb_gadget with the fields ssp_rate and
max_ssp_rate. The gadget driver can use these to setup the device BOS
descriptor and select the desire operating speed and number of lanes.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b6d2196dcc3c73747f91abf9a082b20bbe276cc4.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use SuperSpeed Plus sublink speed macros to fill the BOS descriptor
sublink speed attributes in the composite driver. They're
self-documented so we can remove some of the comments, and this helps
with readability by removing the magic numbers.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6f74d446aa164f66fbe4161e28547e28851f6a02.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for USB 3.2 dual-lane support, add sublink speed
attribute macros and enum usb_ssp_rate. A USB device that operates in
SuperSpeed Plus may operate at different speed and lane count. These
additional macros and enum values help specifying that.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ae9293ebd63a29f2a2035054753534d9eb123d74.1610592135.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BDC PCI driver was only used for design verification with
an PCI/FPGA board. The board no longer exists and is not in use
anywhere. All instances of this core now exist as a memory mapped
device on the platform bus.
NOTE: This only removes the PCI driver and does not remove the
platform driver.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210115213142.35003-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118152615.1644861-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the Pioneer DJ DJM-750 to the quirks table and ensures
skip_pioneer_sync_ep() is (also) called: this device uses the vendor
ID of 0x08e4 (I'm not sure why they use multiple vendor IDs but many
just like to be awkward it seems).
Playback on all 8 channels works. I'll likely keep this working in the
future and submit futher patches and improvements as necessary.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210118130621.77miiie47wp7mump@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed the duplicated peer related function declaration
from core.h since those functions are already declared in peer.h
Founded in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608304793-20612-1-git-send-email-periyasa@codeaurora.org
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200205191043.21913-1-linus.luessing@c0d3.blue
Function ep_rx_complete is being called without NULL checking
in ath10k_htc_rx_completion_handler. Without such check, mal-
formed packet is able to cause jump to NULL.
ep->service_id seems a good candidate for sanity check as it is
used in usb.c.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622022055.16028-1-bruceshenzk@gmail.com
When reading a resource group from disk or when receiving the resource group
statistics from a Lock Value Block (LVB), set/clear the GBF_FULL flags of all
bitmaps in that resource group according to whether or not the resource group
is full.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Removing a reservation doesn't make any actual space available, so don't clear
the GBF_FULL flags in that case. Otherwise, we'll only spend more time
scanning the bitmaps unnecessarily.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
This reverts commit e79e0e1428.
It turns out that we're only setting the GBF_FULL flag of a bitmap if we've
been scanning from the beginning of the bitmap until the end and we haven't
found a single free block, and we're not skipping reservations in that process,
either. This means that in gfs2_rbm_find, we can always skip bitmaps with the
GBF_FULL flag set.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Variable ndata is only used inside "if (!dinode)", so it can be replaced
entirely with *nblocks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
GFS2 uses struct gfs2_rbm to represent a filesystem block number as a
bit position within a resource group. This representation is used in
the bitmap manipulation code to prevent excessive conversions between
block numbers and bit positions, but also in struct gfs2_blkreserv which
is part of struct gfs2_inode, to mark the start of a reservation. In
the inode, the bit position representation makes less sense: first, the
start position is used as a block number about as often as a bit
position; second, the bit position representation makes the code
unnecessarily complicated and difficult to read.
Therefore, change struct gfs2_blkreserv to represent the start of a
reservation as a block number instead of a bit position. (This requires
keeping track of the resource group in gfs2_blkreserv separately.) With
that change, various things can be slightly simplified, and struct
gfs2_rbm can be moved to rgrp.c.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Change gfs2_rbm_incr to advance an rbm by a given number of blocks. Use that
in gfs2_reservation_check_and_update to save a gfs2_rbm_to_block ->
gfs2_rbm_from_block round trip.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Goodix i2c-hid touchscreens are mostly i2c-hid compliant but have some
special power sequencing requirements, including the need to drive a
reset line during the sequencing.
Let's use the new rejiggering of i2c-hid to support this with a thin
wrapper driver to support the first Goodix i2c-hid touchscreen:
GT7375P
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This adds new bindings for the Goodix GT7375P touchscreen. While this
touchscreen's communications are based on the generic "i2c-over-hid"
protocol, it needs special power sequencing and thus gets its own
compatible and bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The i2c-hid driver has been split in two. Let's enable both halves.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch rejiggers the i2c-hid code so that the OF (Open Firmware
aka Device Tree) and ACPI support is separated out a bit. The OF and
ACPI drivers are now separate modules that wrap the core module.
Essentially, what we're doing here:
* Make "power up" and "power down" a function that can be (optionally)
implemented by a given user of the i2c-hid core.
* The OF and ACPI modules are drivers on their own, so they implement
probe / remove / suspend / resume / shutdown. The core code
provides implementations that OF and ACPI can call into.
We'll organize this so that we now have 3 modules: the old i2c-hid
module becomes the "core" module and two new modules will depend on
it, handling probing the specific device.
As part of this work, we'll remove the i2c-hid "platform data"
concept since it's not needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained IRQ
handler").
Based on the mail discussion, it seems ok to drop the error handling.
Link: https://lore.kernel.org/r/20210115212435.19940-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The NPCM750 Timer/Watchdog Controller has multiple interrupt lines,
connected to multiple timers. The driver uses timer 0 for timer
interrupts, so the interrupt line corresponding to timer 0 should be
specified in DT.
I removed the mention of "flags for falling edge", because the timer
controller uses high-level interrupts rather than falling-edge
interrupts, and whether flags should be specified is up the interrupt
controller's DT binding.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210108163004.492649-1-j.neuschaefer@gmx.net
We no longer need to undef pr_fmt if we define our own before including
any headers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210111140814.3668-1-brgl@bgdev.pl
The Renesas Compare Match Timer 0 and 1 (CMT0/1) variants have a
register to control the clock supply to the individual channels.
Currently the driver does not touch this register, and relies on the
documented initial value, which has the clock supply enabled for all
channels present.
However, when Linux starts on the APE6-EVM development board, only the
clock supply to the first CMT1 channel is enabled. Hence the first
channel (used as a clockevent) works, while the second channel (used as
a clocksource) does not. Note that the default system clocksource is
the Cortex-A15 architectured timer, and the user needs to manually
switch to the CMT1 clocksource to trigger the broken behavior.
Fix this by removing the fragile dependency on implicit reset and/or
boot loader state, and by enabling the clock supply explicitly for all
channels used instead. This requires postponing the clk_disable() call,
else the timer's registers cannot be accessed in sh_cmt_setup_channel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210194648.2901899-1-geert+renesas@glider.be
Compile-testing the ixp4xx timer with CONFIG_OF enabled but
CONFIG_TIMER_OF disabled leads to a harmless warning:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ixp4xx.o' being placed in section `__timer_of_table'
Move the select statement from the platform code into the driver
so it always gets enabled in configurations that rely on it.
Fixes: 40df14cc5c ("clocksource/drivers/ixp4xx: Add OF initialization support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210103135955.3808976-1-arnd@kernel.org
Tested on a JZ4740 system (ARCH=mips make qi_lb60_defconfig), this saves
about 14 KiB, by allowing the compiler to garbage-collect all the
functions and tables that correspond to SoCs that were disabled in the
config.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201213235447.138271-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IF_ENABLED(CONFIG_FOO, ptr) evaluates to (ptr) if CONFIG_FOO is set to 'y'
or 'm', NULL otherwise. The (ptr) argument must be a pointer.
The IF_ENABLED() macro can be very useful to help GCC drop dead code.
For instance, consider the following:
#ifdef CONFIG_FOO_SUSPEND
static int foo_suspend(struct device *dev)
{
...
}
#endif
static struct pm_ops foo_ops = {
#ifdef CONFIG_FOO_SUSPEND
.suspend = foo_suspend,
#endif
};
While this works, the foo_suspend() macro is compiled conditionally,
only when CONFIG_FOO_SUSPEND is set. This is problematic, as there could
be a build bug in this function, we wouldn't have a way to know unless
the config option is set.
An alternative is to declare foo_suspend() always, but mark it as maybe
unused:
static int __maybe_unused foo_suspend(struct device *dev)
{
...
}
static struct pm_ops foo_ops = {
#ifdef CONFIG_FOO_SUSPEND
.suspend = foo_suspend,
#endif
};
Again, this works, but the __maybe_unused attribute is required to
instruct the compiler that the function may not be referenced anywhere,
and is safe to remove without making a fuss about it. This makes the
programmer responsible for tagging the functions that can be
garbage-collected.
With this patch, it is now possible to write the following:
static int foo_suspend(struct device *dev)
{
...
}
static struct pm_ops foo_ops = {
.suspend = IF_ENABLED(CONFIG_FOO_SUSPEND, foo_suspend),
};
The foo_suspend() function will now be automatically dropped by the
compiler, and it does not require any specific attribute.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201213235447.138271-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYAFgRQAKCRCKwlD9ZEnx
cEWIAP40TrUerqfnQgJ7iNYLh9WfSk48w9Gxzm92E7FanXaJBAD/dmkieXwQBBig
zKNuoWL2ZlK7O5MMkzpNnhLNS95SEQs=
=vIxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.12
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In commit 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ACPICA commit 5a8390fbd4c5c60da0b6d4ba53b5ee34fda9a0cb
With the exception code class check macros fixed in the previous
commit, let us now use those to simplify exception class checks
across ACPICA.
Link: 5a8390fb
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 1a3a549286ea9db07d7ec700e7a70dd8bcc4354e
The macros to classify different AML exception codes are broken. For
instance,
ACPI_ENV_EXCEPTION(Status)
will always evaluate to zero due to
#define AE_CODE_ENVIRONMENTAL 0x0000
#define ACPI_ENV_EXCEPTION(Status) (Status & AE_CODE_ENVIRONMENTAL)
Similarly, ACPI_AML_EXCEPTION(Status) will evaluate to a non-zero
value for error codes of type AE_CODE_PROGRAMMER, AE_CODE_ACPI_TABLES,
as well as AE_CODE_AML, and not just AE_CODE_AML as the name suggests.
This commit fixes those checks.
Fixes: d46b6537f0 ("ACPICA: AML Parser: ignore all exceptions resulting from incorrect AML during table load")
Link: 1a3a5492
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If we fail to update a block group item in the loop we'll break, however
we'll do btrfs_run_delayed_refs and lose our error value in ret, and
thus not clean up properly. Fix this by only running the delayed refs
if there was no failure.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For now, vmlinux relocation functions for relocatable kernel are
implemented as an array of handlers of a particular type.
Convert that array into a single switch-case function to:
- remove unused arguments;
- change the return type of simple handlers to void;
- remove the array and don't use any data at all;
- avoid using indirect calls;
- allow the compiler to inline and greatly optimize
the relocation function[s];
and also mark do_relocations() and show_kernel_relocation() static
as they aren't used anywhere else.
The result on MIPS32 R2 with GCC 10.2 -O2 is:
scripts/bloat-o-meter -c arch/mips/kernel/__relocate.o arch/mips/kernel/relocate.o
add/remove: 0/6 grow/shrink: 1/0 up/down: 356/-640 (-284)
Function old new delta
relocate_kernel 852 1208 +356
apply_r_mips_32_rel 20 - -20
apply_r_mips_hi16_rel 40 - -40
apply_r_mips_64_rel 44 - -44
apply_r_mips_26_rel 144 - -144
show_kernel_relocation 164 - -164
do_relocations 228 - -228
Total: Before=1780, After=1496, chg -15.96%
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-76 (-76)
Data old new delta
reloc_handlers_rel 76 - -76
Total: Before=92, After=16, chg -82.61%
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
RO Data old new delta
Total: Before=0, After=0, chg +0.00%
All functions were collapsed into the main one, relocate_kernel().
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>