In the case of MSO (Multi-SST Operation), the EDID contains the timings
for a single panel segment. We'll want to hide the fact from userspace,
and expose modes that span the entire display.
Don't modify the EDID, as the userspace should not use that for
modesetting, only modify the actual modes.
v3: Use pixel overlap if available.
v2: Rename intel_dp_mso_mode_fixup -> intel_edp_mso_mode_fixup
Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2862284eb033bb0ffc96134b7d5b11bf29e4587f.1614682842.git.jani.nikula@intel.com
Add splitter configuration to crtc state, and read it where
supported. Also add splitter state dumping. The stream splitter will be
required for eDP MSO.
v4:
- Catch invalid splitter configuration (Uma)
v3:
- Convert segment timings to full panel timings.
- Refer to splitter instead of mso in crtc state.
- Dump splitter state.
v2: Add warning for mso being enabled on pipes other than A.
Cc: Nischal Varide <nischal.varide@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/95cbe1c9d45edf3e3ec252e49fb49055def98155.1614682842.git.jani.nikula@intel.com
the register offset isn't needed division by 4 to pass RREG32_PCIE()
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Currently if stream->signal is neither SIGNAL_TYPE_DISPLAY_PORT_MST or
SIGNAL_TYPE_DISPLAY_PORT then variable ret is uninitialized and this is
checked for > 0 at the end of the function. Ret should be initialized,
I believe setting it to zero is a correct default.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: bd0c064c16 ("drm/amd/display: Add return code instead of boolean for future use")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It works fine and was only disabled because primary GPUs
don't enter runpm if there is a console bound to the fbdev due
to the kmap. This will at least allow runpm on secondary cards.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Arcturus has a different register address from other SMU V11
ASICs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Per discussions with PMFW team, the driver only needs to
notify the PMFW when the RLC is disabled. The RLC FW will notify
the PMFW directly when it's enabled.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Making them an error confuses users and the errors are harmless
as not all asics support all profiles.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1488
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Navi12 0x7360/C7 SKU has no video support, so remove it.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Asher.Song <Asher.Song@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The S0ix check only makes sense if the AMD PMC driver is
present. We need to use the legacy S3 pathes when the
PMC driver is not present.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The existing branch checks for 0 != table->nlpid which always evaluates
true for tables that have an owner.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Skip hook unregistration of owner tables from the netns exit path,
nft_rcv_nl_event() unregisters the table hooks before tearing down
the table content.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5ee759cda5 ("l2tp: use standard API for warning log messages")
changed a number of warnings about invalid packets in the receive path
so that they are always shown, instead of only when a special L2TP debug
flag is set. Even with rate limiting these warnings can easily cause
significant log spam - potentially triggered by a malicious party
sending invalid packets on purpose.
In addition these warnings were noticed by projects like Tunneldigger [1],
which uses L2TP for its data path, but implements its own control
protocol (which is sufficiently different from L2TP data packets that it
would always be passed up to userspace even with future extensions of
L2TP).
Some of the warnings were already redundant, as l2tp_stats has a counter
for these packets. This commit adds one additional counter for invalid
packets that are passed up to userspace. Packets with unknown session are
not counted as invalid, as there is nothing wrong with the format of
these packets.
With the additional counter, all of these messages are either redundant
or benign, so we reduce them to pr_debug_ratelimited().
[1] https://github.com/wlanslovenija/tunneldigger/issues/160
Fixes: 5ee759cda5 ("l2tp: use standard API for warning log messages")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no usrio config defined for default gem config leading to
a kernel panic devices that don't define a data. This issue can be
reprdouced with microchip polar fire soc where compatible string
is defined as "cdns,macb".
Fixes: edac63861d ("add userio bits as platform configuration")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.12. Only three iwlwifi fixes this time, the
crash with MVM being the most important one and reported by multiple
people.
iwlwifi
* fix kernel crash regression when using LTO with MVM devices
* fix printk format warnings
* fix potential deadlock found by lockdep
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgP8G0AAoJEG4XJFUm622b1ZoH/1wSyEwQB90iYlZO4w1pR2yD
HHHJjQQE8JCkOOoMNTHLkCfFWc76c/e6BL3+U9DsbvJGuPccUAIiiUQUonrEMph/
QmNBDd7OB/yIYpmkIpciKpaKAg2Vg4qF2owq8xRDpnD5NosTfCUiacvkuMRB4Wzl
NuGBEECNw6Dq/l/vYVe2pgTQ+rYxCGrvpU7GsYAa5vOsSxzS+4RhMc4gFV5Ae9rK
RNWT4StB7wi8sLjhdEYR2hldyS2OSPnrFNhfJggHw6d/4aXPlmBe7tnd3D1P3kwF
+9FlqjA5U5bcT+3DC2ucFlGtwrfumxi+ro5j8Va19O2/eTLturCIK26A2C+BtTQ=
=cOCt
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-03-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
Second set of fixes for v5.12. Only three iwlwifi fixes this time, the
crash with MVM being the most important one and reported by multiple
people.
iwlwifi
* fix kernel crash regression when using LTO with MVM devices
* fix printk format warnings
* fix potential deadlock found by lockdep
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8b9d680258 ("ACPI: Constify acpi_bus helper functions,
switch to macros") only changed functions for CONFIG_ACPI=y case.
This part adjusts the rest.
Fixes: 8b9d680258 ("ACPI: Constify acpi_bus helper functions, switch to macros")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the following W=1 compilation warning:
drivers/infiniband/core/uverbs_ioctl.c:108: warning: expecting prototype for uverbs_alloc(). Prototype was for _uverbs_alloc() instead
Fixes: 461bb2eee4 ("IB/uverbs: Add a simple allocator to uverbs_attr_bundle")
Link: https://lore.kernel.org/r/20210302074214.1054299-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The W=1 allmodconfig build produces the following warning:
drivers/infiniband/hw/mlx5/odp.c:1086: warning: wrong kernel-doc identifier on line:
* Parse a series of data segments for page fault handling.
Fix it by changing /** to be /* as it is written in kernel-doc
documentation.
Fixes: 5e769e444d ("RDMA/hw/mlx5/odp: Fix formatting and add missing descriptions in 'pagefault_data_segments()'")
Link: https://lore.kernel.org/r/20210302074214.1054299-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
An issue was found, where if a bluetooth client requests a broadcast
advertisement with scan response data, it will not be properly
registered with the controller. This is because at the time that the
hci_cp_le_set_scan_param structure is created, the scan response will
not yet have been received since it comes in a second MGMT call. With
empty scan response, the request defaults to a non-scannable PDU type.
On some controllers, the subsequent scan response request will fail due
to incorrect PDU type, and others will succeed and not use the scan
response.
This fix allows the advertising parameters MGMT call to include a flag
to let the kernel know whether a scan response will be coming, so that
the correct PDU type is used in the first place. A bluetoothd change is
also incoming to take advantage of it.
To test this, I created a broadcast advertisement with scan response
data and registered it on the hatch chromebook. Without this change, the
request fails, and with it will succeed.
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend, there are a few scan enable and set event filter
commands that don't need to be sent unless there are actual BR/EDR
devices capable of waking the system. Check the HCI_PSCAN bit before
writing scan enable and use a new dev flag, HCI_EVENT_FILTER_CONFIGURED
to control whether to clear the event filter.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.
Fixes: 48863ce594 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 7.5 reports:
../drivers/net/ethernet/ibm/ibmvnic.c: In function 'ibmvnic_reset_init':
../drivers/net/ethernet/ibm/ibmvnic.c:5373:51: warning: 'old_num_tx_queues' may be used uninitialized in this function [-Wmaybe-uninitialized]
../drivers/net/ethernet/ibm/ibmvnic.c:5373:6: warning: 'old_num_rx_queues' may be used uninitialized in this function [-Wmaybe-uninitialized]
The variable is initialized only if(reset) and used only if(reset &&
something) so this is a false positive. However, there is no reason to
not initialize the variables unconditionally avoiding the warning.
Fixes: 635e442f4a ("ibmvnic: merge ibmvnic_reset_init and ibmvnic_init")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of "lmac_id" can be controlled by the user and if it is larger
then the number of bits in long then it reads outside the bitmap.
The highest valid value is less than MAX_LMAC_PER_CGX (4).
Fixes: 91c6945ea1 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning "dso not found" is reported when using "perf report -D".
66702781413407 0x32c0 [0x30]: PERF_RECORD_SAMPLE(IP, 0x2): 28177/28177: 0x55e493e00563 period: 106578 addr: 0
... thread: perf:28177
...... dso: <not found>
66702727832429 0x9dd8 [0x38]: PERF_RECORD_COMM exec: triad_loop:28177/28177
The PERF_RECORD_SAMPLE event (timestamp: 66702781413407) should be after the
PERF_RECORD_COMM event (timestamp: 66702727832429), but it's early processed.
So for most of cases, it makes sense to keep the event ordered even for dump
mode. But it would be also useful to disable ordered_events for reporting raw
dump to see events as they are stored in the perf.data file.
So now, set ordered_events by default to true and add a new option
'disable-order' to disable it. For example,
perf report -D --disable-order
Fixes: 977f739b71 ("perf report: Disable ordered_events for raw dump")
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210219070005.12397-1-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
An unsigned long variable should rely on '%lu' format strings, not '%zd'
Fixes: a1a6a4cf49 ("iwlwifi: pnvm: implement reading PNVM from UEFI")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210302011640.1276636-1-pierre-louis.bossart@linux.intel.com
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:181:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: note: (near initialization for ‘aux_mask.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hdcp_i2c_offsets[] array did not have an entry for
HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one
read overflow. I added an entry and copied the 0x0 value for the offset
from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c.
I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX
entries. This doesn't change the code, but it's just a belt and
suspenders approach to try future proof the code.
Fixes: 4c283fdac0 ("drm/amd/display: Add HDCP module")
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the ioctl command RADEON_INFO_SI_BACKEND_ENABLED_MASK can
copy back uninitialised data in value_tmp that pointer *value points
to. This can occur when rdev->family is less than CHIP_BONAIRE and
less than CHIP_TAHITI. Fix this by adding in a missing -EINVAL
so that no invalid value is copied back to userspace.
Addresses-Coverity: ("Uninitialized scalar variable)
Cc: stable@vger.kernel.org # 3.13+
Fixes: 439a1cfffe ("drm/radeon: expose render backend mask to the userspace")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This may avoid debug confusion.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chen Li <chenli@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The number of chunks/chunks_array may be passed in
by userspace and can be large.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chen Li <chenli@uniontech.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c:2252:40-45: WARNING: conversion
to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the register offset isn't needed division by 4 to pass RREG32_PCIE()
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add SECUREDISPLAY TA firmware info in amdgpu_fimrware_info()
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
refine PSP TA firmware info print in amdgpu_firmware_info().
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to correct the name of one function for vangogh.
This function is used to print the clock levels of all kinds of IP
components.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp_cm.c:298:33-38:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Somewhere along the line, probably during a rebase, an unintentional
dump_stack() got included. Revert this change.
Reported-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Fixes: 90cba8d20f ("tpm/ppi: Constify static struct attribute_group")
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The copy_to_user() function returns the number of bytes remaining but
we want to return -EFAULT to the user if it can't complete the copy.
The "st" variable only holds zero on success or negative error codes on
failure so the type should be int.
Fixes: 36f988e978 ("rsxx: Adding in debugfs entries.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Many systems do not use ACPI and hence do not provide a DMI table. On
non-ACPI systems a warning, such as the following, is printed on boot.
WARNING KERN tegra-audio-graph-card sound: ASoC: no DMI vendor name!
The variable 'dmi_available' is not exported and so currently cannot be
used by kernel modules without adding an accessor. However, it is
possible to use the function is_acpi_device_node() to determine if the
sound card is an ACPI device and hence indicate if we expect a DMI table
to be present. Therefore, call is_acpi_device_node() to see if we are
using ACPI and only parse the DMI table if we are booting with ACPI.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210303115526.419458-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>