commit 2c8a7c66c9 upstream.
On the Lenovo ThinkPad X201, when Intel VT-d is enabled in the BIOS, the
kernel boots with errors related to DMAR, the graphical interface appeared
quite choppy, and the system resets erratically within a minute after it
booted:
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:02.0] fault addr 0xb97ff000
[fault reason 0x05] PTE Write access is not set
Upon comparing boot logs with VT-d on/off, I found that the Intel Calpella
quirk (`quirk_calpella_no_shadow_gtt()') correctly applied the igfx IOMMU
disable/quirk correctly:
pci 0000:00:00.0: DMAR: BIOS has allocated no shadow GTT; disabling IOMMU
for graphics
Whereas with VT-d on, it went into the "else" branch, which then
triggered the DMAR handling fault above:
... else if (!disable_igfx_iommu) {
/* we have to ensure the gfx device is idle before we flush */
pci_info(dev, "Disabling batched IOTLB flush on Ironlake\n");
iommu_set_dma_strict();
}
Now, this is not exactly scientific, but moving 0x0044 to quirk_iommu_igfx
seems to have fixed the aforementioned issue. Running a few `git blame'
runs on the function, I have found that the quirk was originally
introduced as a fix specific to ThinkPad X201:
commit 9eecabcb9a ("intel-iommu: Abort IOMMU setup for igfx if BIOS gave
no shadow GTT space")
Which was later revised twice to the "else" branch we saw above:
- 2011: commit 6fbcfb3e46 ("intel-iommu: Workaround IOTLB hang on
Ironlake GPU")
- 2024: commit ba00196ca4 ("iommu/vt-d: Decouple igfx_off from graphic
identity mapping")
I'm uncertain whether further testings on this particular laptops were
done in 2011 and (honestly I'm not sure) 2024, but I would be happy to do
some distro-specific testing if that's what would be required to verify
this patch.
P.S., I also see IDs 0x0040, 0x0062, and 0x006a listed under the same
`quirk_calpella_no_shadow_gtt()' quirk, but I'm not sure how similar these
chipsets are (if they share the same issue with VT-d or even, indeed, if
this issue is specific to a bug in the Lenovo BIOS). With regards to
0x0062, it seems to be a Centrino wireless card, but not a chipset?
I have also listed a couple (distro and kernel) bug reports below as
references (some of them are from 7-8 years ago!), as they seem to be
similar issue found on different Westmere/Ironlake, Haswell, and Broadwell
hardware setups.
Cc: stable@vger.kernel.org
Fixes: 6fbcfb3e46 ("intel-iommu: Workaround IOTLB hang on Ironlake GPU")
Fixes: ba00196ca4 ("iommu/vt-d: Decouple igfx_off from graphic identity mapping")
Link: https://groups.google.com/g/qubes-users/c/4NP4goUds2c?pli=1
Link: https://bugs.archlinux.org/task/65362
Link: https://bbs.archlinux.org/viewtopic.php?id=230323
Reported-by: Wenhao Sun <weiguangtwk@outlook.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=197029
Signed-off-by: Mingcong Bai <jeffbai@aosc.io>
Link: https://lore.kernel.org/r/20250415133330.12528-1-jeffbai@aosc.io
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f7802197 upstream.
UBSan caught a bug with IOMMU SVA domains, where the reported exponent
value in __arm_smmu_tlb_inv_range() was >= 64.
__arm_smmu_tlb_inv_range() uses the domain's pgsize_bitmap to compute
the number of pages to invalidate and the invalidation range. Currently
arm_smmu_sva_domain_alloc() does not setup the iommu domain's
pgsize_bitmap. This leads to __ffs() on the value returning 64 and that
leads to undefined behaviour w.r.t. shift operations
Fix this by initializing the iommu_domain's pgsize_bitmap to PAGE_SIZE.
Effectively the code needs to use the smallest page size for
invalidation
Cc: stable@vger.kernel.org
Fixes: eb6c97647b ("iommu/arm-smmu-v3: Avoid constructing invalid range commands")
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Balbir Singh <balbirs@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jean-Philippe Brucker <jean-philippe@linaro.org>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20250412002354.3071449-1-balbirs@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
commit b00d24997a upstream.
ASPEED VGA card has two built-in devices:
0008:06:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 06)
0008:07:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 52)
Its toplogy looks like this:
+-[0008:00]---00.0-[01-09]--+-00.0-[02-09]--+-00.0-[03]----00.0 Sandisk Corp Device 5017
| +-01.0-[04]--
| +-02.0-[05]----00.0 NVIDIA Corporation Device
| +-03.0-[06-07]----00.0-[07]----00.0 ASPEED Technology, Inc. ASPEED Graphics Family
| +-04.0-[08]----00.0 Renesas Technology Corp. uPD720201 USB 3.0 Host Controller
| \-05.0-[09]----00.0 Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
\-00.1 PMC-Sierra Inc. Device 4028
The IORT logic populaties two identical IDs into the fwspec->ids array via
DMA aliasing in iort_pci_iommu_init() called by pci_for_each_dma_alias().
Though the SMMU driver had been able to handle this situation since commit
563b5cbe33 ("iommu/arm-smmu-v3: Cope with duplicated Stream IDs"), that
got broken by the later commit cdf315f907 ("iommu/arm-smmu-v3: Maintain
a SID->device structure"), which ended up with allocating separate streams
with the same stuffing.
On a kernel prior to v6.15-rc1, there has been an overlooked warning:
pci 0008:07:00.0: vgaarb: setting as boot VGA device
pci 0008:07:00.0: vgaarb: bridge control possible
pci 0008:07:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
pcieport 0008:06:00.0: Adding to iommu group 14
ast 0008:07:00.0: stream 67328 already in tree <===== WARNING
ast 0008:07:00.0: enabling device (0002 -> 0003)
ast 0008:07:00.0: Using default configuration
ast 0008:07:00.0: AST 2600 detected
ast 0008:07:00.0: [drm] Using analog VGA
ast 0008:07:00.0: [drm] dram MCLK=396 Mhz type=1 bus_width=16
[drm] Initialized ast 0.1.0 for 0008:07:00.0 on minor 0
ast 0008:07:00.0: [drm] fb0: astdrmfb frame buffer device
With v6.15-rc, since the commit bcb81ac6ae ("iommu: Get DT/ACPI parsing
into the proper probe path"), the error returned with the warning is moved
to the SMMU device probe flow:
arm_smmu_probe_device+0x15c/0x4c0
__iommu_probe_device+0x150/0x4f8
probe_iommu_group+0x44/0x80
bus_for_each_dev+0x7c/0x100
bus_iommu_probe+0x48/0x1a8
iommu_device_register+0xb8/0x178
arm_smmu_device_probe+0x1350/0x1db0
which then fails the entire SMMU driver probe:
pci 0008:06:00.0: Adding to iommu group 21
pci 0008:07:00.0: stream 67328 already in tree
arm-smmu-v3 arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3 arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
Since SMMU driver had been already expecting a potential duplicated Stream
ID in arm_smmu_install_ste_for_dev(), change the arm_smmu_insert_master()
routine to ignore a duplicated ID from the fwspec->sids array as well.
Note: this has been failing the iommu_device_probe() since 2021, although a
recent iommu commit in v6.15-rc1 that moves iommu_device_probe() started to
fail the SMMU driver probe. Since nobody has cared about DMA Alias support,
leave that as it was but fix the fundamental iommu_device_probe() breakage.
Fixes: cdf315f907 ("iommu/arm-smmu-v3: Maintain a SID->device structure")
Cc: stable@vger.kernel.org
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/20250415185620.504299-1-nicolinc@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dee308e4c upstream.
There is a string parsing logic error which can lead to an overflow of hid
or uid buffers. Comparing ACPIID_LEN against a total string length doesn't
take into account the lengths of individual hid and uid buffers so the
check is insufficient in some cases. For example if the length of hid
string is 4 and the length of the uid string is 260, the length of str
will be equal to ACPIID_LEN + 1 but uid string will overflow uid buffer
which size is 256.
The same applies to the hid string with length 13 and uid string with
length 250.
Check the length of hid and uid strings separately to prevent
buffer overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ca3bf5d47c ("iommu/amd: Introduces ivrs_acpihid kernel parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Paklov <Pavel.Paklov@cyberprotect.ru>
Link: https://lore.kernel.org/r/20250325092259.392844-1-Pavel.Paklov@cyberprotect.ru
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32dce6b194 upstream.
Using "depends on" and "select" for the same Kconfig symbol is known to
cause circular dependencies (cmp. "Kconfig recursive dependency
limitations" in Documentation/kbuild/kconfig-language.rst.
DRM drivers are selecting drm helpers so do the same for
DRM_DEBUG_DP_MST_TOPOLOGY_REFS.
Fixes following circular dependency reported on x86 for the downstream
Asahi Linux tree:
error: recursive dependency detected!
symbol DRM_KMS_HELPER is selected by DRM_GEM_SHMEM_HELPER
symbol DRM_GEM_SHMEM_HELPER is selected by RUST_DRM_GEM_SHMEM_HELPER
symbol RUST_DRM_GEM_SHMEM_HELPER is selected by DRM_ASAHI
symbol DRM_ASAHI depends on RUST
symbol RUST depends on CALL_PADDING
symbol CALL_PADDING depends on OBJTOOL
symbol OBJTOOL is selected by STACK_VALIDATION
symbol STACK_VALIDATION depends on UNWINDER_FRAME_POINTER
symbol UNWINDER_FRAME_POINTER is part of choice block at arch/x86/Kconfig.debug:224
symbol <choice> unknown is visible depending on UNWINDER_GUESS
symbol UNWINDER_GUESS prompt is visible depending on STACKDEPOT
symbol STACKDEPOT is selected by DRM_DEBUG_DP_MST_TOPOLOGY_REFS
symbol DRM_DEBUG_DP_MST_TOPOLOGY_REFS depends on DRM_KMS_HELPER
Fixes: 12a280c728 ("drm/dp_mst: Add topology ref history tracking for debugging")
Cc: stable@vger.kernel.org
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250304-drm_debug_dp_mst_topo_kconfig-v1-1-e16fd152f258@jannau.net
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79af0604eb upstream.
APUs in passthrough mode use HDP flush. 0x7F000 offset used for
remapping HDP flush is mapped to VPE space which could get power gated.
Use another unused offset in BIF space.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d8116a32cd)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a2a6c4281 upstream.
realloc_argv() was only updating the array size if it was called with
old_argv already allocated. The first time it was called to create an
argv array, it would allocate the array but return the array size as
zero. dm_split_args() would think that it couldn't store any arguments
in the array and would call realloc_argv() again, causing it to
reallocate the initial slots (this time using GPF_KERNEL) and finally
return a size. Aside from being wasteful, this could cause deadlocks on
targets that need to process messages without starting new IO. Instead,
realloc_argv should always update the allocated array size on success.
Fixes: a065192655 ("dm table: don't copy from a NULL pointer in realloc_argv()")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a533c3e42 upstream.
If we use the 'B' mode and we have an invalit table line,
cancel_delayed_work_sync would trigger a warning. This commit avoids the
warning.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ed12ab131 upstream.
Commit:
d54d610243 ("x86/boot/sev: Avoid shared GHCB page for early memory acceptance")
provided a fix for SEV-SNP memory acceptance from the EFI stub when
running at VMPL #0. However, that fix was insufficient for SVSM SEV-SNP
guests running at VMPL >0, as those rely on a SVSM calling area, which
is a shared buffer whose address is programmed into a SEV-SNP MSR, and
the SEV init code that sets up this calling area executes much later
during the boot.
Given that booting via the EFI stub at VMPL >0 implies that the firmware
has configured this calling area already, reuse it for performing memory
acceptance in the EFI stub.
Fixes: fcd042e864 ("x86/sev: Perform PVALIDATE using the SVSM when not at VMPL0")
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Co-developed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Dionna Amalie Glaze <dionnaglaze@google.com>
Cc: Kevin Loughlin <kevinloughlin@google.com>
Cc: linux-efi@vger.kernel.org
Link: https://lore.kernel.org/r/20250428174322.2780170-2-ardb+git@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e089e7b58 upstream.
The function brcmf_usb_dl_writeimage() calls the function
brcmf_usb_dl_cmd() but dose not check its return value. The
'state.state' and the 'state.bytes' are uninitialized if the
function brcmf_usb_dl_cmd() fails. It is dangerous to use
uninitialized variables in the conditions.
Add error handling for brcmf_usb_dl_cmd() to jump to error
handling path if the brcmf_usb_dl_cmd() fails and the
'state.state' and the 'state.bytes' are uninitialized.
Improve the error message to report more detailed error
information.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250422042203.2259-1-vulab@iscas.ac.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4426e6b4ec upstream.
The original code would skip null delay pointers, but when the pointers
were converted to point within the spi_device struct, the check was not
updated to skip delays of zero. Hence all spi devices that didn't set
delays would fail to probe.
Fixes: 04e6bb0d6b ("spi: modify set_cs_timing parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://patch.msgid.link/20250423-spi-tegra114-v1-1-2d608bcc12f9@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac8ea8736 upstream.
Commit 61167ad5fe ("mm: pass nid to reserve_bootmem_region()") introduce
a way to set nid to all reserved region.
But there is a corner case it will leave some region with invalid nid.
When memblock_set_node() doubles the array of memblock.reserved, it may
lead to a new reserved region before current position. The new region
will be left with an invalid node id.
Repeat the process when detecting it.
Fixes: 61167ad5fe ("mm: pass nid to reserve_bootmem_region()")
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
CC: Mike Rapoport <rppt@kernel.org>
CC: Yajun Deng <yajun.deng@linux.dev>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250318071948.23854-3-richard.weiyang@gmail.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06eaa824fd upstream.
The second parameter of memblock_set_node() is size instead of end.
Since it iterates from lower address to higher address, finally the node
id is correct. But during the process, some of them are wrong.
Pass size instead of end.
Fixes: 61167ad5fe ("mm: pass nid to reserve_bootmem_region()")
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
CC: Mike Rapoport <rppt@kernel.org>
CC: Yajun Deng <yajun.deng@linux.dev>
CC: stable@vger.kernel.org
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250318071948.23854-2-richard.weiyang@gmail.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38a05c0b87 upstream.
On Qualcomm chipsets not all GPIOs are wakeup capable. Those GPIOs do not
have a corresponding MPM pin and should not be handled inside the MPM
driver. The IRQ domain hierarchy is always applied, so it's required to
explicitly disconnect the hierarchy for those. The pinctrl-msm driver marks
these with GPIO_NO_WAKE_IRQ. qcom-pdc has a check for this, but
irq-qcom-mpm is currently missing the check. This is causing crashes when
setting up interrupts for non-wake GPIOs:
root@rb1:~# gpiomon -c gpiochip1 10
irq: IRQ159: trimming hierarchy from :soc@0:interrupt-controller@f200000-1
Unable to handle kernel paging request at virtual address ffff8000a1dc3820
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pc : mpm_set_type+0x80/0xcc
lr : mpm_set_type+0x5c/0xcc
Call trace:
mpm_set_type+0x80/0xcc (P)
qcom_mpm_set_type+0x64/0x158
irq_chip_set_type_parent+0x20/0x38
msm_gpio_irq_set_type+0x50/0x530
__irq_set_trigger+0x60/0x184
__setup_irq+0x304/0x6bc
request_threaded_irq+0xc8/0x19c
edge_detector_setup+0x260/0x364
linereq_create+0x420/0x5a8
gpio_ioctl+0x2d4/0x6c0
Fix this by copying the check for GPIO_NO_WAKE_IRQ from qcom-pdc.c, so that
MPM is removed entirely from the hierarchy for non-wake GPIOs.
Fixes: a6199bb514 ("irqchip: Add Qualcomm MPM controller driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250502-irq-qcom-mpm-fix-no-wake-v1-1-8a1eafcd28d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f04dd30f1b upstream.
According to the XGMAC specification, enabling features such as Layer 3
and Layer 4 Packet Filtering, Split Header and Virtualized Network support
automatically selects the IPC Full Checksum Offload Engine on the receive
side.
When RX checksum offload is disabled, these dependent features must also
be disabled to prevent abnormal behavior caused by mismatched feature
dependencies.
Ensure that toggling RX checksum offload (disabling or enabling) properly
disables or enables all dependent features, maintaining consistent and
expected behavior in the network device.
Cc: stable@vger.kernel.org
Fixes: 1a510ccf58 ("amd-xgbe: Add support for VXLAN offload capabilities")
Signed-off-by: Vishal Badole <Vishal.Badole@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250424130248.428865-1-Vishal.Badole@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58f6217e5d upstream.
When generating the MSR_IA32_PEBS_ENABLE value that will be loaded on
VM-Entry to a KVM guest, mask the value with the vCPU's desired PEBS_ENABLE
value. Consulting only the host kernel's host vs. guest masks results in
running the guest with PEBS enabled even when the guest doesn't want to use
PEBS. Because KVM uses perf events to proxy the guest virtual PMU, simply
looking at exclude_host can't differentiate between events created by host
userspace, and events created by KVM on behalf of the guest.
Running the guest with PEBS unexpectedly enabled typically manifests as
crashes due to a near-infinite stream of #PFs. E.g. if the guest hasn't
written MSR_IA32_DS_AREA, the CPU will hit page faults on address '0' when
trying to record PEBS events.
The issue is most easily reproduced by running `perf kvm top` from before
commit 7b100989b4 ("perf evlist: Remove __evlist__add_default") (after
which, `perf kvm top` effectively stopped using PEBS). The userspace side
of perf creates a guest-only PEBS event, which intel_guest_get_msrs()
misconstrues a guest-*owned* PEBS event.
Arguably, this is a userspace bug, as enabling PEBS on guest-only events
simply cannot work, and userspace can kill VMs in many other ways (there
is no danger to the host). However, even if this is considered to be bad
userspace behavior, there's zero downside to perf/KVM restricting PEBS to
guest-owned events.
Note, commit 854250329c ("KVM: x86/pmu: Disable guest PEBS temporarily
in two rare situations") fixed the case where host userspace is profiling
KVM *and* userspace, but missed the case where userspace is profiling only
KVM.
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Closes: https://lore.kernel.org/all/Z_VUswFkWiTYI0eD@do-x1carbon
Reported-by: Seth Forshee <sforshee@kernel.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: "Seth Forshee (DigitalOcean)" <sforshee@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250426001355.1026530-1-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75aea4b065 upstream.
A warning in intel_pmu_lbr_counters_reorder() may be triggered by below
perf command.
perf record -e "{cpu-clock,cycles/call-graph="lbr"/}" -- sleep 1
It's because the group is mistakenly treated as a branch counter group.
The hw.flags of the leader are used to determine whether a group is a
branch counters group. However, the hw.flags is only available for a
hardware event. The field to store the flags is a union type. For a
software event, it's a hrtimer. The corresponding bit may be set if the
leader is a software event.
For a branch counter group and other groups that have a group flag
(e.g., topdown, PEBS counters snapshotting, and ACR), the leader must
be a X86 event. Check the X86 event before checking the flag.
The patch only fixes the issue for the branch counter group.
The following patch will fix the other groups.
There may be an alternative way to fix the issue by moving the hw.flags
out of the union type. It should work for now. But it's still possible
that the flags will be used by other types of events later. As long as
that type of event is used as a leader, a similar issue will be
triggered. So the alternative way is dropped.
Fixes: 3374491619 ("perf/x86/intel: Support branch counters logging")
Closes: https://lore.kernel.org/lkml/20250412091423.1839809-1-luogengkun@huaweicloud.com/
Reported-by: Luo Gengkun <luogengkun@huaweicloud.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20250424134718.311934-2-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de3629baf5 upstream.
Camm noticed that on parisc a SIGFPE exception will crash an application with
a second SIGFPE in the signal handler. Dave analyzed it, and it happens
because glibc uses a double-word floating-point store to atomically update
function descriptors. As a result of lazy binding, we hit a floating-point
store in fpe_func almost immediately.
When the T bit is set, an assist exception trap occurs when when the
co-processor encounters *any* floating-point instruction except for a double
store of register %fr0. The latter cancels all pending traps. Let's fix this
by clearing the Trap (T) bit in the FP status register before returning to the
signal handler in userspace.
The issue can be reproduced with this test program:
root@parisc:~# cat fpe.c
static void fpe_func(int sig, siginfo_t *i, void *v) {
sigset_t set;
sigemptyset(&set);
sigaddset(&set, SIGFPE);
sigprocmask(SIG_UNBLOCK, &set, NULL);
printf("GOT signal %d with si_code %ld\n", sig, i->si_code);
}
int main() {
struct sigaction action = {
.sa_sigaction = fpe_func,
.sa_flags = SA_RESTART|SA_SIGINFO };
sigaction(SIGFPE, &action, 0);
feenableexcept(FE_OVERFLOW);
return printf("%lf\n",1.7976931348623158E308*1.7976931348623158E308);
}
root@parisc:~# gcc fpe.c -lm
root@parisc:~# ./a.out
Floating point exception
root@parisc:~# strace -f ./a.out
execve("./a.out", ["./a.out"], 0xf9ac7034 /* 20 vars */) = 0
getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0
...
rt_sigaction(SIGFPE, {sa_handler=0x1110a, sa_mask=[], sa_flags=SA_RESTART|SA_SIGINFO}, NULL, 8) = 0
--- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0x1078f} ---
--- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0xf8f21237} ---
+++ killed by SIGFPE +++
Floating point exception
Signed-off-by: Helge Deller <deller@gmx.de>
Suggested-by: John David Anglin <dave.anglin@bell.net>
Reported-by: Camm Maguire <camm@maguirefamily.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fee4d17145 upstream.
Commit a5951389e5 ("arm64: errata: Add newer ARM cores to the
spectre_bhb_loop_affected() lists") added some additional CPUs to the
Spectre-BHB workaround, including some new arrays for designs that
require new 'k' values for the workaround to be effective.
Unfortunately, the new arrays omitted the sentinel entry and so
is_midr_in_range_list() will walk off the end when it doesn't find a
match. With UBSAN enabled, this leads to a crash during boot when
is_midr_in_range_list() is inlined (which was more common prior to
c8c2647e69 ("arm64: Make _midr_in_range_list() an exported
function")):
| Internal error: aarch64 BRK: 00000000f2000001 [#1] PREEMPT SMP
| pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : spectre_bhb_loop_affected+0x28/0x30
| lr : is_spectre_bhb_affected+0x170/0x190
| [...]
| Call trace:
| spectre_bhb_loop_affected+0x28/0x30
| update_cpu_capabilities+0xc0/0x184
| init_cpu_features+0x188/0x1a4
| cpuinfo_store_boot_cpu+0x4c/0x60
| smp_prepare_boot_cpu+0x38/0x54
| start_kernel+0x8c/0x478
| __primary_switched+0xc8/0xd4
| Code: 6b09011f 54000061 52801080 d65f03c0 (d4200020)
| ---[ end trace 0000000000000000 ]---
| Kernel panic - not syncing: aarch64 BRK: Fatal exception
Add the missing sentinel entries.
Cc: Lee Jones <lee@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: a5951389e5 ("arm64: errata: Add newer ARM cores to the spectre_bhb_loop_affected() lists")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250501104747.28431-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbe5679f30 upstream.
Nouveau is mostly designed in a way that it's expected that fences only
ever get signaled through nouveau_fence_signal(). However, in at least
one other place, nouveau_fence_done(), can signal fences, too. If that
happens (race) a signaled fence remains in the pending list for a while,
until it gets removed by nouveau_fence_update().
Should nouveau_fence_context_kill() run in the meantime, this would be
a bug because the function would attempt to set an error code on an
already signaled fence.
Have nouveau_fence_context_kill() check for a fence being signaled.
Cc: stable@vger.kernel.org # v5.10+
Fixes: ea13e5abf8 ("drm/nouveau: signal pending fences when channel has been killed")
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250415121900.55719-3-phasta@kernel.org
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b1834d620 upstream.
If we unbind a driver from the PCI device with an active DRM client,
subsequent read of the fdinfo data associated with the file descriptor in
question will not end well.
Protect the path with a drm_dev_enter/exit() pair.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes: 3f09a0cd4e ("drm: Add common fdinfo helper")
Cc: <stable@vger.kernel.org> # v6.5+
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250418162512.72324-1-tvrtko.ursulin@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac4e04d9e3 upstream.
When turbo mode is unavailable on a Skylake-X system, executing the
command:
# echo 1 > /sys/devices/system/cpu/intel_pstate/no_turbo
results in an unchecked MSR access error:
WRMSR to 0x199 (attempted to write 0x0000000100001300).
This issue was reproduced on an OEM (Original Equipment Manufacturer)
system and is not a common problem across all Skylake-X systems.
This error occurs because the MSR 0x199 Turbo Engage Bit (bit 32) is set
when turbo mode is disabled. The issue arises when intel_pstate fails to
detect that turbo mode is disabled. Here intel_pstate relies on
MSR_IA32_MISC_ENABLE bit 38 to determine the status of turbo mode.
However, on this system, bit 38 is not set even when turbo mode is
disabled.
According to the Intel Software Developer's Manual (SDM), the BIOS sets
this bit during platform initialization to enable or disable
opportunistic processor performance operations. Logically, this bit
should be set in such cases. However, the SDM also specifies that "OS
and applications must use CPUID leaf 06H to detect processors with
opportunistic processor performance operations enabled."
Therefore, in addition to checking MSR_IA32_MISC_ENABLE bit 38, verify
that CPUID.06H:EAX[1] is 0 to accurately determine if turbo mode is
disabled.
Fixes: 4521e1a0ce ("cpufreq: intel_pstate: Reflect current no_turbo state correctly")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be3f1938d3 upstream.
In run_delalloc_nocow(), when the found btrfs_key's offset > cur_offset,
it indicates a gap between the current processing region and
the next file extent. The original code would directly jump to
the "must_cow" label, which increments the slot and forces a fallback
to COW. This behavior might skip an extent item and result in an
overestimated COW fallback range.
This patch modifies the logic so that when a gap is detected:
- If no COW range is already being recorded (cow_start is unset),
cow_start is set to cur_offset.
- cur_offset is then advanced to the beginning of the next extent.
- Instead of jumping to "must_cow", control flows directly to
"next_slot" so that the same extent item can be reexamined properly.
The change ensures that we accurately account for the extent gap and
avoid accidentally extending the range that needs to fallback to COW.
CC: stable@vger.kernel.org # 6.6+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Dave Chen <davechen@synology.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e08e49d986 upstream.
When running machines with 64k page size and a 16k nodesize we started
seeing tree log corruption in production. This turned out to be because
we were not writing out dirty blocks sometimes, so this in fact affects
all metadata writes.
When writing out a subpage EB we scan the subpage bitmap for a dirty
range. If the range isn't dirty we do
bit_start++;
to move onto the next bit. The problem is the bitmap is based on the
number of sectors that an EB has. So in this case, we have a 64k
pagesize, 16k nodesize, but a 4k sectorsize. This means our bitmap is 4
bits for every node. With a 64k page size we end up with 4 nodes per
page.
To make this easier this is how everything looks
[0 16k 32k 48k ] logical address
[0 4 8 12 ] radix tree offset
[ 64k page ] folio
[ 16k eb ][ 16k eb ][ 16k eb ][ 16k eb ] extent buffers
[ | | | | | | | | | | | | | | | | ] bitmap
Now we use all of our addressing based on fs_info->sectorsize_bits, so
as you can see the above our 16k eb->start turns into radix entry 4.
When we find a dirty range for our eb, we correctly do bit_start +=
sectors_per_node, because if we start at bit 0, the next bit for the
next eb is 4, to correspond to eb->start 16k.
However if our range is clean, we will do bit_start++, which will now
put us offset from our radix tree entries.
In our case, assume that the first time we check the bitmap the block is
not dirty, we increment bit_start so now it == 1, and then we loop
around and check again. This time it is dirty, and we go to find that
start using the following equation
start = folio_start + bit_start * fs_info->sectorsize;
so in the case above, eb->start 0 is now dirty, and we calculate start
as
0 + 1 * fs_info->sectorsize = 4096
4096 >> 12 = 1
Now we're looking up the radix tree for 1, and we won't find an eb.
What's worse is now we're using bit_start == 1, so we do bit_start +=
sectors_per_node, which is now 5. If that eb is dirty we will run into
the same thing, we will look at an offset that is not populated in the
radix tree, and now we're skipping the writeout of dirty extent buffers.
The best fix for this is to not use sectorsize_bits to address nodes,
but that's a larger change. Since this is a fs corruption problem fix
it simply by always using sectors_per_node to increment the start bit.
Fixes: c4aec299fa ("btrfs: introduce submit_eb_subpage() to submit a subpage metadata page")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Boris Burkov <boris@bur.io>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 170d1a3738 upstream.
The vma start address should be substracted from the buffer's user data
address and not the other way around.
Cc: Tiffany Y. Yang <ynaffit@google.com>
Cc: stable <stable@kernel.org>
Fixes: 162c797314 ("binder: avoid user addresses in debug logs")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Tiffany Y. Yang <ynaffit@google.com>
Link: https://lore.kernel.org/r/20250325184902.587138-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[cmllamas: fix conflicts due to alloc->buffer renaming]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1149719442 upstream.
There seem to be multiple USB device IDs used for these;
the one I have reports as 0b0e:030c when powered on.
(When powered off, it reports as 0b0e:0311.)
Signed-off-by: Joachim Priesner <joachim.priesner@web.de>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20250428053606.9237-1-joachim.priesner@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f406005e16 upstream.
During initialisation of Focusrite USB audio interfaces, -EPROTO is
sometimes returned from usb_set_interface(), which sometimes prevents
the device from working: subsequent usb_set_interface() and
uac_clock_source_is_valid() calls fail.
This patch adds up to 5 retries in endpoint_set_interface(), with a
delay starting at 5ms and doubling each time. 5 retries was chosen to
allow for longer than expected waits for the interface to start
responding correctly; in testing, a single 5ms delay was sufficient to
fix the issue.
Closes: https://github.com/geoffreybennett/fcp-support/issues/2
Cc: stable@vger.kernel.org
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://patch.msgid.link/Z//7s9dKsmVxHzY2@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2dd1c1eee3 ]
Add 13 USB device IDs for Qualcomm WCN785x, and these IDs are
extracted from Windows driver inf file for various types of
WoS (Windows on Snapdragon) laptop.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") makes the grammar of MODULE_IMPORT_NS and EXPORT_SYMBOL_NS
different between the stable branches and the mainline. But when
the commit 955f9ede52 ("bpf: Add namespace to BPF internal symbols")
was backported from mainline, only EXPORT_SYMBOL_NS instances are
adapted, leaving the MODULE_IMPORT_NS instance with the "new" grammar
and causing the module fails to build:
ERROR: modpost: module bpf_preload uses symbol bpf_link_get_from_fd from namespace BPF_INTERNAL, but does not import it.
ERROR: modpost: module bpf_preload uses symbol kern_sys_bpf from namespace BPF_INTERNAL, but does not import it.
Reported-by: Mingcong Bai <jeffbai@aosc.io>
Reported-by: Alex Davis <alex47794@gmail.com>
Closes: https://lore.kernel.org/all/CADiockBKBQTVqjA5G+RJ9LBwnEnZ8o0odYnL=LBZ_7QN=_SZ7A@mail.gmail.com/
Fixes: 955f9ede52 ("bpf: Add namespace to BPF internal symbols")
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b0cab327e upstream.
req_get_ioprio looks at req->bio to find the I/O priority, which is not
set when completing bios that the driver fully iterated through.
Stash away the dd_per_prio in the elevator private data instead of looking
it up again to optimize the code a bit while fixing the regression from
removing the per-request ioprio value.
Fixes: 6975c1a486 ("block: remove the ioprio field from struct request")
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241126102136.619067-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398898f9cc upstream.
Currently we get the warning:
"GICv3: [Firmware Bug]: GICR region 0x0000000001900000 has
overlapping address"
As per TRM GICD is 64 KB. Fix it by correcting the size of GICD.
Cc: stable@vger.kernel.org
Fixes: 9cc161a450 ("arm64: dts: ti: Refactor J784s4 SoC files to a common file")
Link: https://lore.kernel.org/r/20250218052248.4734-1-j-keerthy@ti.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 429a98abfc upstream.
We recently added some locking to this function but this error path
was accidentally missed. Unlock before returning.
Fixes: ec27386de2 ("usb: typec: class: Fix NULL pointer access")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/Z_44tOtmml89wQcM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55c78035a1 upstream.
Similar to GCOV, KCOV can leave behind dead code and undefined behavior.
Warnings related to those should be ignored.
The previous commit:
6b023c7842 ("objtool: Silence more KCOV warnings")
... only did so for CONFIG_CGOV_KERNEL. Also do it for CONFIG_KCOV, but
for real this time.
Fixes the following warning:
vmlinux.o: warning: objtool: synaptics_report_mt_data: unexpected end of section .text.synaptics_report_mt_data
Fixes: 6b023c7842 ("objtool: Silence more KCOV warnings")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/a44ba16e194bcbc52c1cef3d3cd9051a62622723.1743481539.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503282236.UhfRsF3B-lkp@intel.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d7597749f upstream.
When KCOV or GCOV is enabled, dead code can be left behind, in which
case objtool silences unreachable and undefined behavior (fallthrough)
warnings.
Fallthrough warnings, and their variant "end of section" warnings, were
silenced with the following commit:
6b023c7842 ("objtool: Silence more KCOV warnings")
Another variant of a fallthrough warning is a jump to the end of a
function. If that function happens to be at the end of a section, the
jump destination doesn't actually exist.
Normally that would be a fatal objtool error, but for KCOV/GCOV it's
just another undefined behavior fallthrough. Silence it like the
others.
Fixes the following warning:
drivers/iommu/dma-iommu.o: warning: objtool: iommu_dma_sw_msi+0x92: can't find jump dest instruction at .text+0x54d5
Fixes: 6b023c7842 ("objtool: Silence more KCOV warnings")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/08fbe7d7e1e20612206f1df253077b94f178d93e.1743481539.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/314f8809-cd59-479b-97d7-49356bf1c8d1@infradead.org/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e3a28793d upstream.
A Short Packet event before the last TRB of a TD is followed by another
event on the final TRB on spec-compliant HCs, which is most of them.
A 'last_td_was_short' flag was added to know if a TD has just completed
as Short Packet and another event is to come. The flag was cleared after
seeing the event (unless no TDs are pending, but that's a separate bug)
or seeing a new TD complete as something other than Short Packet.
A rework replaced the flag with an 'old_trb_comp_code' variable. When
an event doesn't match the pending TD and the previous event was Short
Packet, the new event is silently ignored.
To preserve old behavior, 'old_trb_comp_code' should be cleared at this
point, but instead it is being set to current comp code, which is often
Short Packet again. This can cause more events to be silently ignored,
even though they are no longer connected with the old TD that completed
short and indicate a serious problem with the driver or the xHC.
Common device classes like UAC in async mode, UVC, serial or the UAS
status pipe complete as Short Packet routinely and could be affected.
Clear 'old_trb_comp_code' to zero, which is an invalid completion code
and the same value the variable starts with. This restores original
behavior on Short Packet and also works for illegal Etron events, which
the code has been extended to cover too.
Fixes: b331a3d809 ("xhci: Handle spurious events on Etron host isoc enpoints")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
