Serge Semin says:
====================
net: pcs: xpcs: Cleanups before adding MMIO dev support
As stated in the subject this series is a short prequel before submitting
the main patches adding the memory-mapped DW XPCS support to the DW XPCS
and DW *MAC (STMMAC) drivers. Originally it was a part of the bigger
patchset (see the changelog v2 link below) but was detached to a
preparation set to shrink down the main series thus simplifying it'
review.
The patchset' content is straightforward: drop the redundant sentinel
entry and the header files; return EINVAL errno from the soft-reset method
and make sure that the interface validation method return EINVAL straight
away if the requested interface isn't supported by the XPCS device
instance. All of these changes are required to simplify the changes being
introduced a bit later in the framework of the memory-mapped DW XPCS
support patches.
Link: https://lore.kernel.org/netdev/20231205103559.9605-1-fancer.lancer@gmail.com
Changelog v2:
- Move the preparation patches to a separate series.
- Simplify the commit messages (@Russell, @Vladimir).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If an unsupported interface is passed to the PCS validation callback there
is no need in further link-modes calculations since the resultant array
will be initialized with zeros which will be perceived by the phylink
subsystem as error anyway (see phylink_validate_mac_and_pcs()). Instead
let's explicitly return the -EINVAL error to inform the caller about the
unsupported interface as it's done in the rest of the pcs_validate
callbacks.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular the xpcs_soft_reset() and xpcs_do_config() functions
currently return -1 if invalid auto-negotiation mode is specified. That
value might be then passed to the generic kernel subsystems which require
a standard kernel errno value. Even though the erroneous conditions are
very specific (memory corruption or buggy driver implementation) using a
hard-coded -1 literal doesn't seem correct anyway especially when it comes
to passing it higher to the network subsystem or printing to the system
log. Convert the hard-coded error values to -EINVAL then.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing CM workqueue-related in the driver. So the respective
include directive can be dropped.
While at it add an empty line delimiter between the generic and local path
include directives to visually separate them.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently only two methods (xpcs_find_compat() and
xpcs_get_interfaces()) defined in the driver which loop over the available
interfaces. All of them rely on the xpcs_compat::num_interfaces field
value to get the total number of supported interfaces. Thus the interface
arrays are supposed to be filled with actual interface IDs and there is no
need in the dummy terminating ID placed at the end of the arrays.
Based on the above drop the PHY_INTERFACE_MODE_MAX entry from the
xpcs_2500basex_interfaces array and the PHY_INTERFACE_MODE_MAX-based
conditional statement from the xpcs_get_interfaces() method as redundant.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EDID firmware loading mechanism introduced a few built-in EDIDs that
could be forced on any connector, bypassing the EDIDs it exposes.
While convenient, this limited set of EDIDs doesn't take into account
the connector type, and we can end up with an EDID that is completely
invalid for a given connector.
For example, the edid/800x600.bin file matches the following EDID:
edid-decode (hex):
00 ff ff ff ff ff ff 00 31 d8 00 00 00 00 00 00
05 16 01 03 6d 1b 14 78 ea 5e c0 a4 59 4a 98 25
20 50 54 01 00 00 45 40 01 01 01 01 01 01 01 01
01 01 01 01 01 01 a0 0f 20 00 31 58 1c 20 28 80
14 00 15 d0 10 00 00 1e 00 00 00 ff 00 4c 69 6e
75 78 20 23 30 0a 20 20 20 20 00 00 00 fd 00 3b
3d 24 26 05 00 0a 20 20 20 20 20 20 00 00 00 fc
00 4c 69 6e 75 78 20 53 56 47 41 0a 20 20 00 c2
----------------
Block 0, Base EDID:
EDID Structure Version & Revision: 1.3
Vendor & Product Identification:
Manufacturer: LNX
Model: 0
Made in: week 5 of 2012
Basic Display Parameters & Features:
Analog display
Signal Level Standard: 0.700 : 0.000 : 0.700 V p-p
Blank level equals black level
Sync: Separate Composite Serration
Maximum image size: 27 cm x 20 cm
Gamma: 2.20
DPMS levels: Standby Suspend Off
RGB color display
First detailed timing is the preferred timing
Color Characteristics:
Red : 0.6416, 0.3486
Green: 0.2919, 0.5957
Blue : 0.1474, 0.1250
White: 0.3125, 0.3281
Established Timings I & II:
DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz
Standard Timings:
DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz
Detailed Timing Descriptors:
DTD 1: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz (277 mm x 208 mm)
Hfront 40 Hsync 128 Hback 88 Hpol P
Vfront 1 Vsync 4 Vback 23 Vpol P
Display Product Serial Number: 'Linux #0'
Display Range Limits:
Monitor ranges (GTF): 59-61 Hz V, 36-38 kHz H, max dotclock 50 MHz
Display Product Name: 'Linux SVGA'
Checksum: 0xc2
So, an analog monitor EDID. However, if the connector was an HDMI
monitor for example, it breaks the HDMI specification that requires,
among other things, a digital display, the VIC 1 mode and an HDMI Forum
Vendor Specific Data Block in an CTA-861 extension.
We thus end up with a completely invalid EDID, which thus might confuse
HDMI-related code that could parse it.
After some discussions on IRC, we identified mainly two ways to fix
this:
- We can either create more EDIDs for each connector type to provide
a built-in EDID that matches the resolution passed in the name, and
still be a sensible EDID for that connector type;
- Or we can just prevent the EDID to be exposed to userspace if it's
built-in.
Or possibly both.
However, the conclusion was that maybe we just don't need the built-in
EDIDs at all and we should just get rid of them. So here we are.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221092636.691701-1-mripard@kernel.org
When the kernel is in lockdown mode, debugfs will only show files that
are world-readable and cannot be written, mmaped, or used with ioctl.
That more or less describes the scrub stats file, except that the
permissions are wrong -- they should be 0444, not 0644. You can't write
the stats file, so the 0200 makes no sense.
Meanwhile, the clear_stats file is only writable, but it got mode 0400
instead of 0200, which would make more sense.
Fix both files so that they make sense.
Fixes: d7a74cad8f ("xfs: track usage statistics of online fsck")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Tegra DRM doesn't support display on Tegra234 and later, so make sure
not to remove any existing framebuffers in that case.
v2: - add comments explaining how this situation can come about
- clear DRIVER_MODESET and DRIVER_ATOMIC feature bits
Fixes: 6848c291a5 ("drm/aperture: Convert drivers to aperture interfaces")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223150333.1401582-1-thierry.reding@gmail.com
The hash_pa8 and hashed_bit values in denorm_addr_df4_np2() are
currently defined as u8 types. These variables represent single bits.
'hash_pa8' is set based on logical AND operations using masks with more
than 8 bits. So the calculated value will not fit in this variable. It
will always be '0'. The 'hash_pa8' check later in the function will fail
which produces incorrect results for some cases.
Change these variables to bool type. This clarifies that they are
single bit values. Also, this allows the compiler to ensure they hold
the proper results. Remove an unnecessary shift operation.
[ bp: Remove the unnecessary brackets in the else-branch of the
hash_pa8 assignment. ]
Fixes: 3f3174996b ("RAS: Introduce AMD Address Translation Library")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240222165449.23582-1-yazen.ghannam@amd.com
As the TWL6030 chip is the main power controller here, declare
it as system-power-controller
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-5-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure the TWL6032 as system power controller to let the device
power off.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
early_top_pgt[] is assigned from code that executes from a 1:1 mapping
so it cannot use a plain access from C. Replace the use of
fixup_pointer() with RIP_REL_REF(), which is better and simpler.
For legibility and to align with the code that populates the lower page
table levels, statically initialize the root level page table with an
entry pointing to level3_kernel_pgt[], and overwrite it when needed to
enable 5-level paging.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-24-ardb+git@google.com
The early statically allocated page tables are populated from code that
executes from a 1:1 mapping so it cannot use plain accesses from C.
Replace the use of fixup_pointer() with RIP_REL_REF(), which is better
and simpler.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-23-ardb+git@google.com
'__supported_pte_mask' is accessed from code that executes from a 1:1
mapping so it cannot use a plain access from C. Replace the use of
fixup_pointer() with RIP_REL_REF(), which is better and simpler.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-22-ardb+git@google.com
early_dynamic_pgts[] and next_early_pgt are accessed from code that
executes from a 1:1 mapping so it cannot use a plain access from C.
Replace the use of fixup_pointer() with RIP_REL_REF(), which is better
and simpler.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-21-ardb+git@google.com
'phys_base' is assigned from code that executes from a 1:1 mapping so it
cannot use a plain access from C. Replace the use of fixup_pointer()
with RIP_REL_REF(), which is better and simpler.
While at it, move the assignment to before the addition of the SME mask
so there is no need to subtract it again, and drop the unnecessary
addition ('phys_base' is statically initialized to 0x0)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-20-ardb+git@google.com
There are two code paths in the startup code to program an IDT: one that
runs from the 1:1 mapping and one that runs from the virtual kernel
mapping. Currently, these are strictly separate because fixup_pointer()
is used on the 1:1 path, which will produce the wrong value when used
while executing from the virtual kernel mapping.
Switch to RIP_REL_REF() so that the two code paths can be merged. Also,
move the GDT and IDT descriptors to the stack so that they can be
referenced directly, rather than via RIP_REL_REF().
Rename startup_64_setup_env() to startup_64_setup_gdt_idt() while at it,
to make the call from assembler self-documenting.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240221113506.2565718-19-ardb+git@google.com
Move the pending urls back to https:// and mark the ones that are no
longer accessible (http or https) as defunct.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20240109195500.3833121-1-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
abb_{mpu,ivahd,dspeve,gpu} have 'reg' so they must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/regulator-abb-mpu: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-ivahd: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-dspeve: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-gpu: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-3-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sys_32k_ck node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/clocks/clock-sys-32k: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-2-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy_gmii_sel node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/phy-gmii-sel: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-1-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MHI expects the controller configs to be const, and all of the other ones
in this file already are, so constify modem_telit_fn980_hw_v1_config.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240222-mhi-const-bus-mhi-host-pci_generic-v1-1-d4c9b0b0a7a5@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Eric Dumazet says:
====================
rtnetlink: reduce RTNL pressure for dumps
This series restarts the conversion of rtnl dump operations
to RCU protection, instead of requiring RTNL.
In this new attempt (prior one failed in 2011), I chose to
allow a gradual conversion of selected operations.
After this series, "ip -6 addr" and "ip -4 ro" no longer
need to acquire RTNL.
I refrained from changing inet_dump_ifaddr() and inet6_dump_addr()
to avoid merge conflicts because of two fixes in net tree.
I also started the work for "ip link" future conversion.
v2: rtnl_fill_link_ifmap() always emit IFLA_MAP (Jiri Pirko)
Added "nexthop: allow nexthop_mpath_fill_node()
to be called without RTNL" to avoid a lockdep splat (Ido Schimmel)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
dev->name_node items are already rcu protected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use READ_ONCE() to read the following device fields:
dev->mem_start
dev->mem_end
dev->base_addr
dev->irq
dev->dma
dev->if_port
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer hold RTNL while calling inet_dump_fib().
Also change return value for a completed dump:
Returning 0 instead of skb->len allows NLMSG_DONE
to be appended to the skb. User space does not have
to call us again to get a standalone NLMSG_DONE marker.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nexthop_mpath_fill_node() will be potentially called
from contexts holding rcu_lock instead of RTNL.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/all/ZdZDWVdjMaQkXBgW@shredder/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new field into struct fib_dump_filter, to let callers
tell if they use RTNL locking or RCU.
This is used in the following patch, when inet_dump_fib()
no longer holds RTNL.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer hold RTNL while calling inet6_dump_ifinfo()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to RTNL_FLAG_DOIT_UNLOCKED, this new flag
allows dump operations registered via rtnl_register()
or rtnl_register_module() to opt-out from RTNL protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit af65bdfce9 ("[NETLINK]: Switch cb_lock spinlock
to mutex and allow to override it"), Patrick McHardy used
a common mutex to protect both nlk->cb and the dump() operations.
The override is used for rtnl dumps, registered with
rntl_register() and rntl_register_module().
We want to be able to opt-out some dump() operations
to not acquire RTNL, so we need to protect nlk->cb
with a per socket mutex.
This patch renames nlk->cb_def_mutex to nlk->nl_cb_mutex
The optional pointer to the mutex used to protect dump()
call is stored in nlk->dump_cb_mutex
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__netlink_dump_start() releases nlk->cb_mutex right before
calling netlink_dump() which grabs it again.
This seems dangerous, even if KASAN did not bother yet.
Add a @lock_taken parameter to netlink_dump() to let it
grab the mutex if called from netlink_recvmsg() only.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__netlink_diag_dump() returns 1 if the dump is not complete,
zero if no error occurred.
If err variable is zero, this means the dump is complete:
We should not return skb->len in this case, but 0.
This allows NLMSG_DONE to be appended to the skb.
User space does not have to call us again only to get NLMSG_DONE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare inet6_dump_ifinfo() to run with RCU protection
instead of RTNL and use for_each_netdev_dump() interface.
Also properly return 0 at the end of a dump, avoiding
an extra recvmsg() system call and RTNL acquisition.
Note that RTNL-less dumps need core changes, coming later
in the series.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use RCU protection instead of RTNL
for inet6_fill_ifinfo().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to no longer hold RTNL while calling inet6_fill_ifla6_attrs()
in the future. Add needed READ_ONCE()/WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
This patch prepares dev_get_iflink() and nla_put_iflink()
to run either with RTNL or RCU held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jérémie Dautheribes says:
====================
Add support for TI DP83826 configuration
This short patch series introduces the possibility of overriding
some parameters which are latched by default by hardware straps on the
TI DP83826 PHY.
The settings that can be overridden include:
- Configuring the PHY in either MII mode or RMII mode.
- When in RMII mode, configuring the PHY in RMII slave mode or RMII
master mode.
The RMII master/slave mode is TI-specific and determines whether the PHY
operates from a 25MHz reference clock (master mode) or from a 50MHz
reference clock (slave mode).
While these features should be supported by all the TI DP8382x family,
I have only been able to test them on TI DP83826 hardware. Therefore,
support has been added specifically for this PHY in this patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI DP83826 PHY can operate between two RMII modes:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
By default, the operation mode is configured by hardware straps.
Add support to configure the operation mode from within the driver.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI DP83826 PHY can operate in either MII mode or RMII mode.
By default, it is configured by straps.
It can also be configured by writing to the bit 5 of register 0x17 - RMII
and Status Register (RCSR).
When phydev->interface is rmii, rmii mode must be enabled, otherwise
mii mode must be set.
This prevents misconfiguration of hw straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add property ti,rmii-mode to support selecting the RMII operation mode
between:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
If not set, the operation mode is configured by hardware straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that we keep GRO flag in sync when XDP is disabled while
the device is closed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Infineon SPI NOR flash devices support hybrid sector layout that
overlays 4KB sectors on a 256KB sector and SPI NOR framework recognizes
that by parsing SMPT and construct params->erase_map. The hybrid sector
layout is similar to CFI flash devices that have small sectors on top
and/or bottom address. In case of CFI flash devices, the erase map
information is parsed through CFI table and populated into
mtd->eraseregions so that users can create MTD partitions that aligned
with small sector boundaries. This patch provides the same capability to
SPI NOR flash devices that have non-uniform erase map.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/35d0962986e493b06c13bdf7ada8130a9966dc02.1708404584.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Introduce n_regions in spi_nor_erase_map structure and remove
SNOR_LAST_REGION flag. Loop logics that depend on the flag are also
reworked to use n_regions as loop condition.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/eded84294bd81e966d6f423e578fc2cfb9a4a5b6.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: update spi_nor_init_erase_cmd_list() and break the for loop sooner.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
For now let's not update the clock-dss-tv-fck as it seems to share the same
register bit as the clock-dss-96m-fck and would introduce more warnings.
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
