Consolidate the wraparound fields in the memory interface interrupt
status registers, so that it can be more succinctly expressed by taking
the stream ID (main or self) as a parameter.
Link: https://lore.kernel.org/r/20231201140433.2126011-2-paul.elder@ideasonboard.com
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the
interrupts and then apparently assumes that the interrupt handler won't
be running, and proceeds in the stop procedure. This is not the case, as
the interrupt handler can already be running, which would lead to the
ISP being disabled while the interrupt handler handling a captured
frame.
This brings up two issues: 1) the ISP could be powered off while the
interrupt handler is still running and accessing registers, leading to
board lockup, and 2) the interrupt handler code and the code that
disables the streaming might do things that conflict.
It is not clear to me if 2) causes a real issue, but 1) can be seen with
a suitable delay (or printk in my case) in the interrupt handler,
leading to board lockup.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-4-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Store the IRQ lines used by the driver for easy access. These are needed
in future patches which fix IRQ race issues.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-3-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IRQ handler rkisp1_isr() calls sub-handlers, all of which returns an
irqreturn_t value, but rkisp1_isr() ignores those values and always
returns IRQ_HANDLED.
Fix this by collecting the return values, and returning IRQ_HANDLED or
IRQ_NONE as appropriate.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-2-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The bus-type belongs to the endpoint's properties and should therefore
be moved.
Link: https://lore.kernel.org/r/20231115164407.99876-1-mehdi.djait@bootlin.com
Fixes: 6a0eaa25bf ("media: dt-bindings: media: rkisp1: Add port for parallel interface")
Signed-off-by: Mehdi Djait <mehdi.djait@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The extended address registers are missing in the debug output register
list. These are only available on 36-Bit DMA platforms. Due to the
prolonged name, the output width has to be adjusted as well.
Link: https://lore.kernel.org/r/20231207110918.1338524-1-alexander.stein@ew.tq-group.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver always enables the clocks at probe() and disables them only
at remove(). It is not clear why the driver does this, as it supports
runtime PM, and enables and disables the clocks in the runtime resume
and suspend callbacks. Also, in the case runtime PM is not available,
the driver calls the resume and suspend callbacks manually from probe()
and remove().
Drop the unnecessary clock enable, thus enabling the clocks only when
actually needed.
Link: https://lore.kernel.org/r/20231122-imx-csis-v2-2-e44b8dc4cb66@ideasonboard.com
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver always calls mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in remove(). This causes multiple WARNs from the
kernel, as the clocks get disabled too many times.
Fix the remove() to call mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in a way that reverses what is done in probe().
Link: https://lore.kernel.org/r/20231122-imx-csis-v2-1-e44b8dc4cb66@ideasonboard.com
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Include all the headers that the driver needs explicitly instead of
relying on indirect inclusion. While at it, drop a few unneeded headers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The device does not implement the power line frequency control
correctly. It is a UVC 1.5 device, but implements the control as a UVC
1.1 device.
Add the corresponding control mapping override.
Bus 003 Device 002: ID 2b7e:b752 SunplusIT Inc HD Camera
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.01
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x2b7e
idProduct 0xb752
bcdDevice 0.04
iManufacturer 1 SunplusIT Inc
iProduct 2 HD Camera
iSerial 3 01.00.00
bNumConfigurations 1
Cc: Yunke Cao <yunkec@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When selecting an alternate setting, the driver loops over all available
alternate settings to find the one with the lowest bandwidth high enough
for the selected format and resolution. While all alternate settings
should have different packet sizes, some buggy devices report multiple
alternate settings with the same size. The driver happens to pick the
last one in this case.
In theory this should work fine, but in real life we have device bugs.
The Ali Corp. Newmine Camera (0402:8841) exposes four alternate
settings with the same packet size. The first three seem to work fine,
while selecting the last one results in lots of transmission errors.
Switch to using the first best alternate setting when multiple are
present. This should be safe (last famous words), as sniffing USB
traffic with the faulty device shows that Windows 10 picks the first
alternate setting, and devices are typically tested on Windows.
Closes: https://lore.kernel.org/linux-media/Nh6D0WI--3-9@tutanota.com/
Reported-by: Karel Janda <karel1@tutanota.com>
Suggested-by: Karel Janda <karel1@tutanota.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The device does not implement the control properly.
Fixes v4l2-compliance error:
info: checking control 'Power Line Frequency' (0x00980918)
fail: v4l2-test-controls.cpp(552): could not set valid menu item 3
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The vb2 read support requests 1 buffer, leaving it to the driver
to increase this number to something that works.
Unfortunately, drivers do not deal with this reliably, and in fact
this caused problems for the bttv driver and reading from /dev/vbiX,
causing every other VBI frame to be all 0.
Instead, request as the number of buffers whatever is the maximum of
2 and q->min_buffers_needed+1.
In order to start streaming you need at least q->min_buffers_needed
queued buffers, so add 1 buffer for processing. And if that field
is 0, then choose 2 (again, one buffer is being filled while the
other one is being processed).
This certainly makes more sense than requesting just 1 buffer, and
the VBI bttv support is now working again.
It turns out that the old videobuf1 behavior of bttv was to allocate
8 (video) and 4 (vbi) buffers when used with read(). After the vb2
conversion that changed to 2 for both. With this patch it is 3, which
is really all you need.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: b7ec3212a7 ("media: bttv: convert to vb2")
Tested-by: Dr. David Alan Gilbert <dave@treblig.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The old (now removed) videobuf framework had an optional vbi hack where
the sequence number of the frame counter was copied in the last 4 bytes
of the buffer. This hack was active only for the read() interface
(so not for streaming I/O), and it was enabled by bttv. This allowed
applications that used read() for the VBI data to match it with the
corresponding video frame.
When bttv was converted to vb2 this hack was forgotten, but some old
applications rely on this.
So add this back, but this time in the bttv driver rather than in the
vb2 framework.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: b7ec3212a7 ("media: bttv: convert to vb2")
Tested-by: Dr. David Alan Gilbert <dave@treblig.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The start_streaming callback returned 0 or 1 instead of a
proper error code. Fix that.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: b7ec3212a7 ("media: bttv: convert to vb2")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the node for the ADSP found on the SC7280 SoC, using standard
Qualcomm firmware.
Remove the reserved-memory node from sc7280-chrome-common since CDSP is
currently not used there.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231208-sc7280-remoteprocs-v3-9-6aa394d33edf@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The wpss-pil driver wants to manage too many resources that cannot be
touched with standard Qualcomm firmware.
Use the compatible from the PAS driver and move the ChromeOS-specific
bits to sc7280-chrome-common.dtsi.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231208-sc7280-remoteprocs-v3-7-6aa394d33edf@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The dtbs_check really doesn't like having memory without reg set.
The base address depends on the amount of RAM you have:
<= 2.00 GiB RAM: 0x80000000
= 3.00 GiB RAM: 0x40000000
= 3.75 GiB RAM: 0x10000000
(more does not fit into the 32-bit physical address space)
So, let's pick one of the values, 0x10000000 which is used on devices
with 3.75 GiB RAM. Since the bootloader will update it to what's present
on the device it doesn't matter too much.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20231125-msm8953-misc-fixes-v2-1-df86655841d9@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some platforms don't use the built-in charging hardware (e.g. milletwifi).
As this is an optional peripheral, default it to off.
Keep it enabled for all other boards that use smbb.
Signed-off-by: Bryant Mairs <bryant@mai.rs>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231203-smbb-pm8941-pm8226-v1-1-9ad75909604b@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add UFS host controller and PHY nodes for sc7280 soc.
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[luca: various cleanups and additions as written in the cover letter]
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231205-sc7280-ufs-v6-2-ad6ca7796de7@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Assuming crtc->state is pointing at the correct thing for the
async flip commit is nonsense. If we had already queued up multiple
commits this would point at the very lates crtc state even if the
older commits hadn't even happened yet.
Instead properly stage/arm the event like we do for async flips.
Since we don't need to arm multiple of these at the same time we
don't need a list like the normal vblank even processing uses.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230928152450.30109-1-ville.syrjala@linux.intel.com
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
When the chip is configured to timestamp all receive packets, the
timestamp in the RX completion is only valid if the metadata
present flag is not set for packets received on the wire. In
addition, internal loopback packets will never have a valid timestamp
and the timestamp field will always be zero. We must exclude
any 0 value in the timestamp field because there is no way to
determine if it is a loopback packet or not.
Add a new function bnxt_rx_ts_valid() to check for all timestamp
valid conditions.
Fixes: 66ed81dced ("bnxt_en: Enable packet timestamping for all RX packets")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231208001658.14230-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The wait_event_interruptible_timeout() function returns 0
if the timeout elapsed, -ERESTARTSYS if it was interrupted
by a signal, and the remaining jiffies otherwise if the
condition evaluated to true before the timeout elapsed.
Driver should have checked for zero return value instead of
a positive value.
MChan: Print a warning for -ERESTARTSYS. The close operation
will proceed anyway when wait_event_interruptible_timeout()
returns for any reason. Since we do the close no matter what,
we should not return this error code to the caller. Change
bnxt_close_nic() to a void function and remove all error
handling from some of the callers.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231208001658.14230-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Receive SKBs can go through the VF-rep path or the normal path.
skb_mark_for_recycle() is only called for the normal path. Fix it
to do it for both paths to fix possible stalled page pool shutdown
errors.
Fixes: 86b05508f7 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231208001658.14230-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are issuing HWRM_FUNC_RESET cmd to reset the device including
all reserved resources, but not clearing the reservations
within the driver struct. As a result, when the driver re-initializes
as part of resume, it believes that there is no need to do any
resource reservation and goes ahead and tries to allocate rings
which will eventually fail beyond a certain number pre-reserved by
the firmware.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231208001658.14230-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
My prior patch went a bit too far, because apparently fib6_has_expires()
could be true while f6i->gc_link is not hashed yet.
fib6_set_expires_locked() can indeed set RTF_EXPIRES
while f6i->fib6_table is NULL.
Original syzbot reports were about corruptions caused
by dangling f6i->gc_link.
Fixes: 5a08d0065a ("ipv6: add debug checks in fib6_info_release()")
Reported-by: syzbot+c15aa445274af8674f41@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kui-Feng Lee <thinker.li@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20231207201322.549000-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 939463016b ("tcp: change data receiver flowlabel after one dup")
we noticed an increase of TCPACKSkippedPAWS events.
Neal Cardwell tracked the issue to tcp_disordered_ack() assumption
about remote peer TS clock.
RFC 1323 & 7323 are suggesting the following:
"timestamp clock frequency in the range 1 ms to 1 sec per tick
between 1ms and 1sec."
This has to be adjusted for 1 MHz clock frequency.
This hints at reorders of SACK packets on send side,
this might deserve a future patch.
(skb->ooo_okay is always set for pure ACK packets)
Fixes: 614e8316aa ("tcp: add support for usec resolution in TCP TS values")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Morley <morleyd@google.com>
Link: https://lore.kernel.org/r/20231207181342.525181-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before the change on `i686-linux` `systemd` build failed as:
$ bpftool gen object src/core/bpf/socket_bind/socket-bind.bpf.o src/core/bpf/socket_bind/socket-bind.bpf.unstripped.o
Error: failed to link 'src/core/bpf/socket_bind/socket-bind.bpf.unstripped.o': Invalid argument (22)
After the change it fails as:
$ bpftool gen object src/core/bpf/socket_bind/socket-bind.bpf.o src/core/bpf/socket_bind/socket-bind.bpf.unstripped.o
libbpf: ELF section #9 has inconsistent alignment addr=8 != d=4 in src/core/bpf/socket_bind/socket-bind.bpf.unstripped.o
Error: failed to link 'src/core/bpf/socket_bind/socket-bind.bpf.unstripped.o': Invalid argument (22)
Now it's slightly easier to figure out what is wrong with an ELF file.
Signed-off-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20231208215100.435876-1-slyich@gmail.com
Yafang Shao says:
====================
In the current cgroup1 environment, associating operations between a cgroup
and applications in a BPF program requires storing a mapping of cgroup_id
to application either in a hash map or maintaining it in userspace.
However, by enabling bpf_cgrp_storage for cgroup1, it becomes possible to
conveniently store application-specific information in cgroup-local storage
and utilize it within BPF programs. Furthermore, enabling this feature for
cgroup1 involves minor modifications for the non-attach case, streamlining
the process.
However, when it comes to enabling this functionality for the cgroup1
attach case, it presents challenges. Therefore, the decision is to focus on
enabling it solely for the cgroup1 non-attach case at present. If
attempting to attach to a cgroup1 fd, the operation will simply fail with
the error code -EBADF.
Changes:
- RFC -> v1:
- Collect acked-by
- Avoid unnecessary is_cgroup1 check (Yonghong)
- Keep the code patterns consistent (Yonghong)
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This new helper allows us to obtain the fd of a net_cls cgroup, which will
be utilized in the subsequent patch.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20231206115326.4295-3-laoar.shao@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
In the current cgroup1 environment, associating operations between cgroups
and applications in a BPF program requires storing a mapping of cgroup_id
to application either in a hash map or maintaining it in userspace.
However, by enabling bpf_cgrp_storage for cgroup1, it becomes possible to
conveniently store application-specific information in cgroup-local storage
and utilize it within BPF programs. Furthermore, enabling this feature for
cgroup1 involves minor modifications for the non-attach case, streamlining
the process.
However, when it comes to enabling this functionality for the cgroup1
attach case, it presents challenges. Therefore, the decision is to focus on
enabling it solely for the cgroup1 non-attach case at present. If
attempting to attach to a cgroup1 fd, the operation will simply fail with
the error code -EBADF.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20231206115326.4295-2-laoar.shao@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Because test_bad_ret main program is not written in assembly, we don't
control instruction indices in timer_cb_ret_bad() subprog. This bites us
in timer/test_bad_ret subtest, where we see difference between cpuv4 and
other flavors.
For now, make __msg() expectations not rely on instruction indices by
anchoring them around bpf_get_prandom_u32 call. Once we have regex/glob
support for __msg(), this can be expressed a bit more nicely, but for
now just mitigating the problem with available means.
Fixes: e02dea158d ("selftests/bpf: validate async callback return value check correctness")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231208233028.3412690-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Legacy ARC700 processors (first generation of MMU enabled ARC cores) had
VIPT cached which could be configured such that they could alias.
Corresponding support in kernel (with all the obnoxious cache flush overhead)
was added in ARC port 10 years ago to support 1 silicon. That is long bygone
and we can let it RIP.
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
And for ARcompact variant replace the PUSH/POP macros with gas provided
push/pop pseudo-instructions
This allows ISA specific implementation
e.g. Current ARCv2 PUSH/POP could be replaced with STD/LDL to save 2
registers at a time (w/o bothering with SP update each time) or
perhaps use ENTER_S/LEAVE_S to reduce code size
For ARCv3 ABI changed so callee regs are now r14-r26 (vs. r13-r25)
thus would need a different implementation.
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Merge series from Linus Walleij <linus.walleij@linaro.org>:
This converts the remaining Wolfson ASoC codecs to
use GPIO descriptors.
These Wolfson codecs are mostly used with different
Samsung S3C (especially Cragganmore 6410) board files,
so the in-tree users are fixed up in the process.