commit a92a6c50e3 upstream.
This is another one of those XGSPON ONU sticks that's using the
X-ONU-SFPP internally, thus it also requires the potron quirk to avoid tx
faults. So, add an entry for it in sfp_quirks[].
Cc: stable@vger.kernel.org
Signed-off-by: Hamza Mahfooz <someguy@effective-light.com>
Link: https://patch.msgid.link/20260113232957.609642-1-someguy@effective-light.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1bb3fedf upstream.
The MAX_FL (maximum frame length) and related calculations used ETH_HLEN,
which does not account for the 4-byte VLAN tag in tagged frames. This
caused the hardware to reject valid VLAN frames as oversized, resulting
in RX errors and dropped packets.
Use VLAN_ETH_HLEN instead of ETH_HLEN in the MAX_FL register setup,
cut-through mode threshold, buffer allocation, and max_mtu calculation.
Cc: stable@kernel.org # v6.18+
Fixes: 62b5bb7be7 ("net: fec: update MAX_FL based on the current MTU")
Fixes: d466c16026 ("net: fec: enable the Jumbo frame support for i.MX8QM")
Fixes: 59e9bf037d ("net: fec: add change_mtu to support dynamic buffer allocation")
Fixes: ec2a1681ed ("net: fec: use a member variable for maximum buffer size")
Signed-off-by: Clemens Gruber <mail@clemensgruber.at>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260121083751.66997-1-mail@clemensgruber.at
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d76a7d89c upstream.
On 32-bit machines with CONFIG_ARM_LPAE, it is possible for lowmem
allocations to be backed by addresses physical memory above the 32-bit
address limit, as found while experimenting with larger VMSPLIT
configurations.
This caused the qemu virt model to crash in the GICv3 driver, which
allocates the 'itt' object using GFP_KERNEL. Since all memory below
the 4GB physical address limit is in ZONE_DMA in this configuration,
kmalloc() defaults to higher addresses for ZONE_NORMAL, and the
ITS driver stores the physical address in a 32-bit 'unsigned long'
variable.
Change the itt_addr variable to the correct phys_addr_t type instead,
along with all other variables in this driver that hold a physical
address.
The gicv5 driver correctly uses u64 variables, while all other irqchip
drivers don't call virt_to_phys or similar interfaces. It's expected that
other device drivers have similar issues, but fixing this one is
sufficient for booting a virtio based guest.
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260119201603.2713066-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91dcfae0ff upstream.
By default when users program perf to sample branch instructions
(PERF_COUNT_HW_BRANCH_INSTRUCTIONS) with a sample period of 1, perf
interprets this as a special case and enables BTS (Branch Trace Store)
as an optimization to avoid taking an interrupt on every branch.
Since BTS doesn't virtualize, this optimization doesn't make sense when
the request originates from a guest. Add an additional check that
prevents this optimization for virtualized events (exclude_host).
Reported-by: Jan H. Schönherr <jschoenh@amazon.de>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fernand Sieber <sieberf@amazon.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20251211183604.868641-1-sieberf@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5fe8bcd3 upstream.
Fix the following:
BUG: KCSAN: data-race in rxrpc_peer_keepalive_worker / rxrpc_send_data_packet
which is reporting an issue with the reads and writes to ->last_tx_at in:
conn->peer->last_tx_at = ktime_get_seconds();
and:
keepalive_at = peer->last_tx_at + RXRPC_KEEPALIVE_TIME;
The lockless accesses to these to values aren't actually a problem as the
read only needs an approximate time of last transmission for the purposes
of deciding whether or not the transmission of a keepalive packet is
warranted yet.
Also, as ->last_tx_at is a 64-bit value, tearing can occur on a 32-bit
arch.
Fix both of these by switching to an unsigned int for ->last_tx_at and only
storing the LSW of the time64_t. It can then be reconstructed at need
provided no more than 68 years has elapsed since the last transmission.
Fixes: ace45bec6d ("rxrpc: Fix firewall route keepalive")
Reported-by: syzbot+6182afad5045e6703b3d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/695e7cfb.050a0220.1c677c.036b.GAE@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: stable@kernel.org
Link: https://patch.msgid.link/1107124.1768903985@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d9c4c272b upstream.
`build_assert` relies on the compiler to optimize out its error path.
Functions using it with its arguments must thus always be inlined,
otherwise the error path of `build_assert` might not be optimized out,
triggering a build error.
Cc: stable@vger.kernel.org
Fixes: 746680ec66 ("rust: irq: add flags module")
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Link: https://patch.msgid.link/20251208-io-build-assert-v3-6-98aded02c1ea@nvidia.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33d19f6216 upstream.
`build_assert` relies on the compiler to optimize out its error path.
Functions using it with its arguments must thus always be inlined,
otherwise the error path of `build_assert` might not be optimized out,
triggering a build error.
Cc: stable@vger.kernel.org
Fixes: ce30d94e68 ("rust: add `io::{Io, IoRaw}` base types")
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Timur Tabi <ttabi@nvidia.com>
Link: https://patch.msgid.link/20251208-io-build-assert-v3-2-98aded02c1ea@nvidia.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861d21c43c upstream.
RK3588_PD_NPU initialize as GENPD_STATE_ON before regulator ready.
rknn_iommu initlized success and suspend RK3588_PD_NPU. When rocket
driver register, it will resume rknn_iommu.
If regulator is still not ready at this point, rknn_iommu resume fail,
pm runtime status will be error: -EPROBE_DEFER.
This patch set pmdomain to off if it need regulator during probe,
consumer device can power on pmdomain after regulator ready.
Signed-off-by: Frank Zhang <rmxpzlb@gmail.com>
Tested-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: db6df2e3fc ("pmdomain: rockchip: add regulator support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3de4996649 upstream.
For i.MX8MQ platform, the ADB in the VPUMIX domain has no separate reset
and clock enable bits, but is ungated and reset together with the VPUs.
So we can't reset G1 or G2 separately, it may led to the system hang.
Remove rst_mask and clk_mask of imx8mq_vpu_blk_ctl_domain_data.
Let imx8mq_vpu_power_notifier() do really vpu reset.
Fixes: 608d7c325e ("soc: imx: imx8m-blk-ctrl: add i.MX8MQ VPU blk-ctrl")
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 467d4afc6c upstream.
hp-bioscfg has a MODULE_DEVICE_TABLE with a GUID in it that looks
plausible, but the module doesn't automatically load on applicable
systems.
This is because the GUID has some lower case characters and so it
doesn't match the modalias during boot. Update the GUIDs to be all
uppercase.
Cc: stable@vger.kernel.org
Fixes: 5f94f181ca ("platform/x86: hp-bioscfg: bioscfg-h")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20260115203725.828434-4-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c08dabe5 upstream.
Directly calling `put_queue` carries risks since it cannot
guarantee that resources of `uacce_queue` have been fully released
beforehand. So adding a `stop_queue` operation for the
UACCE_CMD_PUT_Q command and leaving the `put_queue` operation to
the final resource release ensures safety.
Queue states are defined as follows:
- UACCE_Q_ZOMBIE: Initial state
- UACCE_Q_INIT: After opening `uacce`
- UACCE_Q_STARTED: After `start` is issued via `ioctl`
When executing `poweroff -f` in virt while accelerator are still
working, `uacce_fops_release` and `uacce_remove` may execute
concurrently. This can cause `uacce_put_queue` within
`uacce_fops_release` to access a NULL `ops` pointer. Therefore, add
state checks to prevent accessing freed pointers.
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-5-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02695347be upstream.
The current uacce_vm_ops does not support the mremap operation of
vm_operations_struct. Implement .mremap to return -EPERM to remind
users.
The reason we need to explicitly disable mremap is that when the
driver does not implement .mremap, it uses the default mremap
method. This could lead to a risk scenario:
An application might first mmap address p1, then mremap to p2,
followed by munmap(p1), and finally munmap(p2). Since the default
mremap copies the original vma's vm_private_data (i.e., q) to the
new vma, both munmap operations would trigger vma_close, causing
q->qfr to be freed twice(qfr will be set to null here, so repeated
release is ok).
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-4-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98eec34925 upstream.
uacce supports the device isolation feature. If the driver
implements the isolate_err_threshold_read and
isolate_err_threshold_write callback functions, uacce will create
sysfs files now. Users can read and configure the isolation policy
through sysfs. Currently, sysfs files are created as long as either
isolate_err_threshold_read or isolate_err_threshold_write callback
functions are present.
However, accessing a non-existent callback function may cause the
system to crash. Therefore, intercept the creation of sysfs if
neither read nor write exists; create sysfs if either is supported,
but intercept unsupported operations at the call site.
Fixes: e3e289fbc0 ("uacce: supports device isolation feature")
Cc: stable@vger.kernel.org
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-3-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3bece3678 upstream.
When cdev_device_add fails, it internally releases the cdev memory,
and if cdev_device_del is then executed, it will cause a hang error.
To fix it, we check the return value of cdev_device_add() and clear
uacce->cdev to avoid calling cdev_device_del in the uacce_remove.
Fixes: 015d239ac0 ("uacce: add uacce driver")
Cc: stable@vger.kernel.org
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://patch.msgid.link/20251202061256.4158641-2-huangchenghai2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddc6cbef3e upstream.
Since commit 3e86e4d74c ("kbuild: keep .modinfo section in
vmlinux.unstripped") the .modinfo section which has SHF_ALLOC ends up
in bzImage after the SecureBoot trailer. This breaks SecureBoot because
the bootloader can no longer find the SecureBoot trailer with kernel's
signature at the expected location in bzImage. To fix the bug,
move discarded sections before the ELF_DETAILS macro and discard
the .modinfo section which is not needed by the decompressor.
Fixes: 3e86e4d74c ("kbuild: keep .modinfo section in vmlinux.unstripped")
Cc: stable@vger.kernel.org
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3317785a88 upstream.
The upper limit of the firmware queue fill state for each APQN
is reported by the hwinfo.qd field. This field shows the
numbers 0-7 for 1-8 queue spaces available. But the exploiting
code assumed the real boundary is stored there and thus stoppes
queuing in messages one tick too early.
Correct the limit calculation and thus offer a boost
of 12.5% performance for high traffic on one APQN.
Fixes: d4c53ae8e4 ("s390/ap: store TAPQ hwinfo in struct ap_card")
Cc: stable@vger.kernel.org
Reported-by: Ingo Franzki <ifranzki@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06d5a7afe1 upstream.
The commit
afd2627f72 ("tracing: Check "%s" dereference via the field and not the TP_printk format")
forbids to emit event with a plain char* without a wrapper.
The reg parameter always passed as static string and wrapper
is not strictly required, contrary to dev parameter.
Use the string wrapper anyway to check sanity of the reg parameters,
store it value independently and prevent internal kernel data leaks.
Since some code refactoring has taken place, explicit backporting may
be needed for kernels older than 6.10.
Cc: stable@vger.kernel.org # v6.11+
Fixes: a0a927d06d ("mei: me: add io register tracing")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://patch.msgid.link/20260111145125.1754912-1-alexander.usyskin@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95fc36a234 upstream.
Make sure to drop the reference taken when looking up the th device
during output device open() on errors and on close().
Note that a recent commit fixed the leak in a couple of open() error
paths but not all of them, and the reference is still leaking on
successful open().
Fixes: 39f4034693 ("intel_th: Add driver infrastructure for Intel(R) Trace Hub devices")
Fixes: 6d5925b667 ("intel_th: Fix error handling in intel_th_output_open")
Cc: stable@vger.kernel.org # 4.4: 6d5925b667
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251208153524.68637-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90f9f5d64c upstream.
When creating a synthetic event based on an existing synthetic event that
had a stacktrace field and the new synthetic event used that field a
kernel crash occurred:
~# cd /sys/kernel/tracing
~# echo 's:stack unsigned long stack[];' > dynamic_events
~# echo 'hist:keys=prev_pid:s0=common_stacktrace if prev_state & 3' >> events/sched/sched_switch/trigger
~# echo 'hist:keys=next_pid:s1=$s0:onmatch(sched.sched_switch).trace(stack,$s1)' >> events/sched/sched_switch/trigger
The above creates a synthetic event that takes a stacktrace when a task
schedules out in a non-running state and passes that stacktrace to the
sched_switch event when that task schedules back in. It triggers the
"stack" synthetic event that has a stacktrace as its field (called "stack").
~# echo 's:syscall_stack s64 id; unsigned long stack[];' >> dynamic_events
~# echo 'hist:keys=common_pid:s2=stack' >> events/synthetic/stack/trigger
~# echo 'hist:keys=common_pid:s3=$s2,i0=id:onmatch(synthetic.stack).trace(syscall_stack,$i0,$s3)' >> events/raw_syscalls/sys_exit/trigger
The above makes another synthetic event called "syscall_stack" that
attaches the first synthetic event (stack) to the sys_exit trace event and
records the stacktrace from the stack event with the id of the system call
that is exiting.
When enabling this event (or using it in a historgram):
~# echo 1 > events/synthetic/syscall_stack/enable
Produces a kernel crash!
BUG: unable to handle page fault for address: 0000000000400010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP PTI
CPU: 6 UID: 0 PID: 1257 Comm: bash Not tainted 6.16.3+deb14-amd64 #1 PREEMPT(lazy) Debian 6.16.3-1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
RIP: 0010:trace_event_raw_event_synth+0x90/0x380
Code: c5 00 00 00 00 85 d2 0f 84 e1 00 00 00 31 db eb 34 0f 1f 00 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 2e 0f 1f 84 00 00 00 00 00 <49> 8b 04 24 48 83 c3 01 8d 0c c5 08 00 00 00 01 cd 41 3b 5d 40 0f
RSP: 0018:ffffd2670388f958 EFLAGS: 00010202
RAX: ffff8ba1065cc100 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: fffff266ffda7b90 RDI: ffffd2670388f9b0
RBP: 0000000000000010 R08: ffff8ba104e76000 R09: ffffd2670388fa50
R10: ffff8ba102dd42e0 R11: ffffffff9a908970 R12: 0000000000400010
R13: ffff8ba10a246400 R14: ffff8ba10a710220 R15: fffff266ffda7b90
FS: 00007fa3bc63f740(0000) GS:ffff8ba2e0f48000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000400010 CR3: 0000000107f9e003 CR4: 0000000000172ef0
Call Trace:
<TASK>
? __tracing_map_insert+0x208/0x3a0
action_trace+0x67/0x70
event_hist_trigger+0x633/0x6d0
event_triggers_call+0x82/0x130
trace_event_buffer_commit+0x19d/0x250
trace_event_raw_event_sys_exit+0x62/0xb0
syscall_exit_work+0x9d/0x140
do_syscall_64+0x20a/0x2f0
? trace_event_raw_event_sched_switch+0x12b/0x170
? save_fpregs_to_fpstate+0x3e/0x90
? _raw_spin_unlock+0xe/0x30
? finish_task_switch.isra.0+0x97/0x2c0
? __rseq_handle_notify_resume+0xad/0x4c0
? __schedule+0x4b8/0xd00
? restore_fpregs_from_fpstate+0x3c/0x90
? switch_fpu_return+0x5b/0xe0
? do_syscall_64+0x1ef/0x2f0
? do_fault+0x2e9/0x540
? __handle_mm_fault+0x7d1/0xf70
? count_memcg_events+0x167/0x1d0
? handle_mm_fault+0x1d7/0x2e0
? do_user_addr_fault+0x2c3/0x7f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The reason is that the stacktrace field is not labeled as such, and is
treated as a normal field and not as a dynamic event that it is.
In trace_event_raw_event_synth() the event is field is still treated as a
dynamic array, but the retrieval of the data is considered a normal field,
and the reference is just the meta data:
// Meta data is retrieved instead of a dynamic array
str_val = (char *)(long)var_ref_vals[val_idx];
// Then when it tries to process it:
len = *((unsigned long *)str_val) + 1;
It triggers a kernel page fault.
To fix this, first when defining the fields of the first synthetic event,
set the filter type to FILTER_STACKTRACE. This is used later by the second
synthetic event to know that this field is a stacktrace. When creating
the field of the new synthetic event, have it use this FILTER_STACKTRACE
to know to create a stacktrace field to copy the stacktrace into.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Link: https://patch.msgid.link/20260122194824.6905a38e@gandalf.local.home
Fixes: 00cf3d672a ("tracing: Allow synthetic events to pass around stacktraces")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9391380eb9 upstream.
Slimbus devices can be allocated dynamically upon reception of
report-present messages.
Make sure to drop the reference taken when looking up already registered
devices.
Note that this requires taking an extra reference in case the device has
not yet been registered and has to be allocated.
Fixes: 46a2bb5a7f ("slimbus: core: Add slim controllers support")
Cc: stable@vger.kernel.org # 4.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251126145329.5022-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eb4ff6596 upstream.
Make sure to balance the runtime PM usage count in case slimbus device
or address allocation fails on report present, which would otherwise
prevent the controller from suspending.
Fixes: 4b14e62ad3 ("slimbus: Add support for 'clock-pause' feature")
Cc: stable@vger.kernel.org # 4.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20251126145329.5022-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d998b0e5af upstream.
0 is a valid DMA address [1] so using it as the error value can lead to
errors. The error value of dma_map_XXX() functions is DMA_MAPPING_ERROR
which is ~0. The callers of otx2_dma_map_page() use dma_mapping_error()
to test the return value of otx2_dma_map_page(). This means that they
would not detect an error in otx2_dma_map_page().
Make otx2_dma_map_page() return the raw value of dma_map_page_attrs().
[1] https://lore.kernel.org/all/f977f68b-cec5-4ab7-b4bd-2cf6aca46267@intel.com
Fixes: caa2da34fd ("octeontx2-pf: Initialize and config queues")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20260114123107.42387-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98e3e2b561 upstream.
The dma_unmap_sg() functions should be called with the same nents as the
dma_map_sg(), not the value the map function returned.
Fixes: 0626e6641f ("cifsd: add server handler for central processing and tranport layers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2907cbe9e upstream.
When SME is supported, Restoring SVE signal context can go wrong in a
few ways, including placing the task into an invalid state where the
kernel may read from out-of-bounds memory (and may potentially take a
fatal fault) and/or may kill the task with a SIGKILL.
(1) Restoring a context with SVE_SIG_FLAG_SM set can place the task into
an invalid state where SVCR.SM is set (and sve_state is non-NULL)
but TIF_SME is clear, consequently resuting in out-of-bounds memory
reads and/or killing the task with SIGKILL.
This can only occur in unusual (but legitimate) cases where the SVE
signal context has either been modified by userspace or was saved in
the context of another task (e.g. as with CRIU), as otherwise the
presence of an SVE signal context with SVE_SIG_FLAG_SM implies that
TIF_SME is already set.
While in this state, task_fpsimd_load() will NOT configure SMCR_ELx
(leaving some arbitrary value configured in hardware) before
restoring SVCR and attempting to restore the streaming mode SVE
registers from memory via sve_load_state(). As the value of
SMCR_ELx.LEN may be larger than the task's streaming SVE vector
length, this may read memory outside of the task's allocated
sve_state, reading unrelated data and/or triggering a fault.
While this can result in secrets being loaded into streaming SVE
registers, these values are never exposed. As TIF_SME is clear,
fpsimd_bind_task_to_cpu() will configure CPACR_ELx.SMEN to trap EL0
accesses to streaming mode SVE registers, so these cannot be
accessed directly at EL0. As fpsimd_save_user_state() verifies the
live vector length before saving (S)SVE state to memory, no secret
values can be saved back to memory (and hence cannot be observed via
ptrace, signals, etc).
When the live vector length doesn't match the expected vector length
for the task, fpsimd_save_user_state() will send a fatal SIGKILL
signal to the task. Hence the task may be killed after executing
userspace for some period of time.
(2) Restoring a context with SVE_SIG_FLAG_SM clear does not clear the
task's SVCR.SM. If SVCR.SM was set prior to restoring the context,
then the task will be left in streaming mode unexpectedly, and some
register state will be combined inconsistently, though the task will
be left in legitimate state from the kernel's PoV.
This can only occur in unusual (but legitimate) cases where ptrace
has been used to set SVCR.SM after entry to the sigreturn syscall,
as syscall entry clears SVCR.SM.
In these cases, the the provided SVE register data will be loaded
into the task's sve_state using the non-streaming SVE vector length
and the FPSIMD registers will be merged into this using the
streaming SVE vector length.
Fix (1) by setting TIF_SME when setting SVCR.SM. This also requires
ensuring that the task's sme_state has been allocated, but as this could
contain live ZA state, it should not be zeroed. Fix (2) by clearing
SVCR.SM when restoring a SVE signal context with SVE_SIG_FLAG_SM clear.
For consistency, I've pulled the manipulation of SVCR, TIF_SVE, TIF_SME,
and fp_type earlier, immediately after the allocation of
sve_state/sme_state, before the restore of the actual register state.
This makes it easier to ensure that these are always modified
consistently, even if a fault is taken while reading the register data
from the signal context. I do not expect any software to depend on the
exact state restored when a fault is taken while reading the context.
Fixes: 85ed24dad2 ("arm64/sme: Implement streaming SVE signal handling")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea8ccfddbc upstream.
The code to restore a ZA context doesn't attempt to allocate the task's
sve_state before setting TIF_SME. Consequently, restoring a ZA context
can place a task into an invalid state where TIF_SME is set but the
task's sve_state is NULL.
In legitimate but uncommon cases where the ZA signal context was NOT
created by the kernel in the context of the same task (e.g. if the task
is saved/restored with something like CRIU), we have no guarantee that
sve_state had been allocated previously. In these cases, userspace can
enter streaming mode without trapping while sve_state is NULL, causing a
later NULL pointer dereference when the kernel attempts to store the
register state:
| # ./sigreturn-za
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
| Mem abort info:
| ESR = 0x0000000096000046
| EC = 0x25: DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| FSC = 0x06: level 2 translation fault
| Data abort info:
| ISV = 0, ISS = 0x00000046, ISS2 = 0x00000000
| CM = 0, WnR = 1, TnD = 0, TagAccess = 0
| GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
| user pgtable: 4k pages, 52-bit VAs, pgdp=0000000101f47c00
| [0000000000000000] pgd=08000001021d8403, p4d=0800000102274403, pud=0800000102275403, pmd=0000000000000000
| Internal error: Oops: 0000000096000046 [#1] SMP
| Modules linked in:
| CPU: 0 UID: 0 PID: 153 Comm: sigreturn-za Not tainted 6.19.0-rc1 #1 PREEMPT
| Hardware name: linux,dummy-virt (DT)
| pstate: 214000c9 (nzCv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
| pc : sve_save_state+0x4/0xf0
| lr : fpsimd_save_user_state+0xb0/0x1c0
| sp : ffff80008070bcc0
| x29: ffff80008070bcc0 x28: fff00000c1ca4c40 x27: 63cfa172fb5cf658
| x26: fff00000c1ca5228 x25: 0000000000000000 x24: 0000000000000000
| x23: 0000000000000000 x22: fff00000c1ca4c40 x21: fff00000c1ca4c40
| x20: 0000000000000020 x19: fff00000ff6900f0 x18: 0000000000000000
| x17: fff05e8e0311f000 x16: 0000000000000000 x15: 028fca8f3bdaf21c
| x14: 0000000000000212 x13: fff00000c0209f10 x12: 0000000000000020
| x11: 0000000000200b20 x10: 0000000000000000 x9 : fff00000ff69dcc0
| x8 : 00000000000003f2 x7 : 0000000000000001 x6 : fff00000c1ca5b48
| x5 : fff05e8e0311f000 x4 : 0000000008000000 x3 : 0000000000000000
| x2 : 0000000000000001 x1 : fff00000c1ca5970 x0 : 0000000000000440
| Call trace:
| sve_save_state+0x4/0xf0 (P)
| fpsimd_thread_switch+0x48/0x198
| __switch_to+0x20/0x1c0
| __schedule+0x36c/0xce0
| schedule+0x34/0x11c
| exit_to_user_mode_loop+0x124/0x188
| el0_interrupt+0xc8/0xd8
| __el0_irq_handler_common+0x18/0x24
| el0t_64_irq_handler+0x10/0x1c
| el0t_64_irq+0x198/0x19c
| Code: 54000040 d51b4408 d65f03c0 d503245f (e5bb5800)
| ---[ end trace 0000000000000000 ]---
Fix this by having restore_za_context() ensure that the task's sve_state
is allocated, matching what we do when taking an SME trap. Any live
SVE/SSVE state (which is restored earlier from a separate signal
context) must be preserved, and hence this is not zeroed.
Fixes: 39782210eb ("arm64/sme: Implement ZA signal handling")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 128a7494a9 upstream.
When SVE is supported but SME is not supported, a ptrace write to the
NT_ARM_SVE regset can place the tracee into an invalid state where
(non-streaming) SVE register data is stored in FP_STATE_SVE format but
TIF_SVE is clear. This can result in a later warning from
fpsimd_restore_current_state(), e.g.
WARNING: CPU: 0 PID: 7214 at arch/arm64/kernel/fpsimd.c:383 fpsimd_restore_current_state+0x50c/0x748
When this happens, fpsimd_restore_current_state() will set TIF_SVE,
placing the task into the correct state. This occurs before any other
check of TIF_SVE can possibly occur, as other checks of TIF_SVE only
happen while the FPSIMD/SVE/SME state is live. Thus, aside from the
warning, there is no functional issue.
This bug was introduced during rework to error handling in commit:
9f8bf718f2 ("arm64/fpsimd: ptrace: Gracefully handle errors")
... where the setting of TIF_SVE was moved into a block which is only
executed when system_supports_sme() is true.
Fix this by removing the system_supports_sme() check. This ensures that
TIF_SVE is set for (SVE-formatted) writes to NT_ARM_SVE, at the cost of
unconditionally manipulating the tracee's saved svcr value. The
manipulation of svcr is benign and inexpensive, and we already do
similar elsewhere (e.g. during signal handling), so I don't think it's
worth guarding this with system_supports_sme() checks.
Aside from the above, there is no functional change. The 'type' argument
to sve_set_common() is only set to ARM64_VEC_SME (in ssve_set())) when
system_supports_sme(), so the ARM64_VEC_SME case in the switch statement
is still unreachable when !system_supports_sme(). When
CONFIG_ARM64_SME=n, the only caller of sve_set_common() is sve_set(),
and the compiler can constant-fold for the case where type is
ARM64_VEC_SVE, removing the logic for other cases.
Reported-by: syzbot+d4ab35af21e99d07ce67@syzkaller.appspotmail.com
Fixes: 9f8bf718f2 ("arm64/fpsimd: ptrace: Gracefully handle errors")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f431d88ea upstream.
The struct ieee80211_vif contains trailing space for vif driver data,
when struct ieee80211_vif is allocated, the total memory size that is
allocated is sizeof(struct ieee80211_vif) + size of vif driver data.
The size of vif driver data is set by each WiFi driver as needed.
The RSI911x driver does not set vif driver data size, no trailing space
for vif driver data is therefore allocated past struct ieee80211_vif .
The RSI911x driver does however use the vif driver data to store its
vif driver data structure "struct vif_priv". An access to vif->drv_priv
leads to access out of struct ieee80211_vif bounds and corruption of
some memory.
In case of the failure observed locally, rsi_mac80211_add_interface()
would write struct vif_priv *vif_info = (struct vif_priv *)vif->drv_priv;
vif_info->vap_id = vap_idx. This write corrupts struct fq_tin member
struct list_head new_flows . The flow = list_first_entry(head, struct
fq_flow, flowchain); in fq_tin_reset() then reports non-NULL bogus
address, which when accessed causes a crash.
The trigger is very simple, boot the machine with init=/bin/sh , mount
devtmpfs, sysfs, procfs, and then do "ip link set wlan0 up", "sleep 1",
"ip link set wlan0 down" and the crash occurs.
Fix this by setting the correct size of vif driver data, which is the
size of "struct vif_priv", so that memory is allocated and the driver
can store its driver data in it, instead of corrupting memory around
it.
Cc: stable@vger.kernel.org
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Link: https://patch.msgid.link/20260109235817.150330-1-marex@nabladev.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2120f3a373 upstream.
The "i" iterator variable is used to count two different things but
unfortunately we can't store two different numbers in the same variable.
Use "i" for the outside loop and "j" for the inside loop.
Cc: stable@vger.kernel.org
Fixes: d219b7eb37 ("mwifiex: handle BT coex event to adjust Rx BA window size")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jeff Chen <jeff.chen_1@nxp.com>
Link: https://patch.msgid.link/aWAM2MGUWRP0zWUd@stanley.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb97131fbf upstream.
dma_alloc_coherent() allocates a DMA mapped buffer and stores the
addresses in XXX_unaligned fields. Those should be reused when freeing
the buffer rather than the aligned addresses.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260106084905.18622-2-fourier.thomas@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9282a1e171 upstream.
dma_alloc_coherent() allocates a DMA mapped buffer and stores the
addresses in XXX_unaligned fields. Those should be reused when freeing
the buffer rather than the aligned addresses.
Fixes: 2a1e1ad3fd ("ath10k: Add support for 64 bit ce descriptor")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260105210439.20131-2-fourier.thomas@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 604826acb3 upstream.
Apparently we never actually filled these in, despite the fact that we do
in fact technically support atomic modesetting.
Since not having these filled in causes us to potentially forget to disable
fbdev and friends during suspend/resume, let's fix it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20260121191320.210342-1-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 374e7af67d upstream.
__arm_lpae_unmap() returns size_t but was returning -ENOENT (negative
error code) when encountering an unmapped PTE. Since size_t is unsigned,
-ENOENT (typically -2) becomes a huge positive value (0xFFFFFFFFFFFFFFFE
on 64-bit systems).
This corrupted value propagates through the call chain:
__arm_lpae_unmap() returns -ENOENT as size_t
-> arm_lpae_unmap_pages() returns it
-> __iommu_unmap() adds it to iova address
-> iommu_pgsize() triggers BUG_ON due to corrupted iova
This can cause IOVA address overflow in __iommu_unmap() loop and
trigger BUG_ON in iommu_pgsize() from invalid address alignment.
Fix by returning 0 instead of -ENOENT. The WARN_ON already signals
the error condition, and returning 0 (meaning "nothing unmapped")
is the correct semantic for size_t return type. This matches the
behavior of other io-pgtable implementations (io-pgtable-arm-v7s,
io-pgtable-dart) which return 0 on error conditions.
Fixes: 3318f7b5ce ("iommu/io-pgtable-arm: Add quirk to quiet WARN_ON()")
Cc: stable@vger.kernel.org
Signed-off-by: Chaitanya Kulkarni <ckulkarnilinux@gmail.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1226102201 upstream.
rtsx_pci_sdmmc does not have an sdmmc_card_busy function, so any voltage
switches cause a kernel warning, "mmc0: cannot verify signal voltage
switch."
Copy the sdmmc_card_busy function from rtsx_pci_usb to rtsx_pci_sdmmc to
fix this.
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Tested-by: Ricky WU <ricky_wu@realtek.com>
Reviewed-by: Ricky WU <ricky_wu@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 930e69757b upstream.
When snd_usb_create_mixer() fails, snd_usb_mixer_free() frees
mixer->id_elems but the controls already added to the card still
reference the freed memory. Later when snd_card_register() runs,
the OSS mixer layer calls their callbacks and hits a use-after-free read.
Call trace:
get_ctl_value+0x63f/0x820 sound/usb/mixer.c:411
get_min_max_with_quirks.isra.0+0x240/0x1f40 sound/usb/mixer.c:1241
mixer_ctl_feature_info+0x26b/0x490 sound/usb/mixer.c:1381
snd_mixer_oss_build_test+0x174/0x3a0 sound/core/oss/mixer_oss.c:887
...
snd_card_register+0x4ed/0x6d0 sound/core/init.c:923
usb_audio_probe+0x5ef/0x2a90 sound/usb/card.c:1025
Fix by calling snd_ctl_remove() for all mixer controls before freeing
id_elems. We save the next pointer first because snd_ctl_remove()
frees the current element.
Fixes: 6639b6c236 ("[ALSA] usb-audio - add mixer control notifications")
Cc: stable@vger.kernel.org
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Berk Cem Goksel <berkcgoksel@gmail.com>
Link: https://patch.msgid.link/20260120102855.7300-1-berkcgoksel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f5c69f72e upstream.
The scarlett2_usb_get_config() function has a logic error in the
endianness conversion code that can cause buffer overflows when
count > 1.
The code checks `if (size == 2)` where `size` is the total buffer size in
bytes, then loops `count` times treating each element as u16 (2 bytes).
This causes the loop to access `count * 2` bytes when the buffer only
has `size` bytes allocated.
Fix by checking the element size (config_item->size) instead of the
total buffer size. This ensures the endianness conversion matches the
actual element type.
Fixes: ac34df733d ("ALSA: usb-audio: scarlett2: Update get_config to do endian conversion")
Cc: stable@vger.kernel.org
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Link: https://patch.msgid.link/20260117012706.1715574-1-samasth.norway.ananda@oracle.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61006c540c upstream.
In the audio mixer handling code of ctxfi driver, the conf field is
used as a kind of loop index, and it's referred in the index callbacks
(amixer_index() and sum_index()).
As spotted recently by fuzzers, the current code causes OOB access at
those functions.
| UBSAN: array-index-out-of-bounds in /build/reproducible-path/linux-6.17.8/sound/pci/ctxfi/ctamixer.c:347:48
| index 8 is out of range for type 'unsigned char [8]'
After the analysis, the cause was found to be the lack of the proper
(re-)initialization of conj field.
This patch addresses those OOB accesses by adding the proper
initializations of the loop indices.
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Karsten Hohmeier <linux@hohmatik.de>
Closes: https://bugs.debian.org/1121535
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/aSk8KJI35H7gFru6@eldamar.lan/
Link: https://patch.msgid.link/20260119133212.189129-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 441ac29923 upstream.
The chip info for this variant (I2C, four channels, 14 bit, internal
reference) seems to have been left out due to oversight, so
ad5686_chip_info_tbl[ID_AD5695R] is all zeroes. Initialisation of an
AD5695R still succeeds, but the resulting IIO device has no channels and no
/dev/iio:device* node.
Add the missing chip info to the table.
Fixes: 4177381b44 ("iio:dac:ad5686: Add AD5671R/75R/94/94R/95R/96/96R support")
Signed-off-by: Andreas Kübrich <andreas.kuebrich@spektra-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 978d28136c upstream.
When simple_write_to_buffer() succeeds, it returns the number of bytes
actually copied to the buffer. The code incorrectly uses 'count'
as the index for null termination instead of the actual bytes copied.
If count exceeds the buffer size, this leads to out-of-bounds write.
Add a check for the count and use the return value as the index.
The bug was validated using a demo module that mirrors the original
code and was tested under QEMU.
Pattern of the bug:
- A fixed 64-byte stack buffer is filled using count.
- If count > 64, the code still does buf[count] = '\0', causing an
- out-of-bounds write on the stack.
Steps for reproduce:
- Opens the device node.
- Writes 128 bytes of A to it.
- This overflows the 64-byte stack buffer and KASAN reports the OOB.
Found via static analysis. This is similar to the
commit da9374819e ("iio: backend: fix out-of-bound write")
Fixes: b1c5d68ea6 ("iio: dac: ad3552r-hs: add support for internal ramp")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d5a5366d upstream.
The driver converts values read from the sensor from BE to CPU
endianness in scd4x_read_meas(). The result is then pushed into the
buffer in scd4x_trigger_handler(), so on LE architectures parsing the
buffer using the reported BE type gave wrong results.
scd4x_read_raw() which provides sysfs *_raw values is not affected, it
used the values returned by scd4x_read_meas() without further
conversion.
Fixes: 49d22b695c ("drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor")
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da934ef0fd upstream.
The local variable 'curr_energy' was never clamped to
PAC_193X_MIN_POWER_ACC or PAC_193X_MAX_POWER_ACC because the return
value of clamp() was not used. Fix this by assigning the clamped value
back to 'curr_energy'.
Cc: stable@vger.kernel.org
Fixes: 0fb528c825 ("iio: adc: adding support for PAC193x")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea6b4feba8 upstream.
Since commit c6e126de43 ("of: Keep track of populated platform
devices") child devices will not be created by of_platform_populate()
if the devices had previously been deregistered individually so that the
OF_POPULATED flag is still set in the corresponding OF nodes.
Switch to using of_platform_depopulate() instead of open coding so that
the child devices are created if the driver is rebound.
Fixes: c6e126de43 ("of: Keep track of populated platform devices")
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbdb442218 upstream.
at91_adc_interrupt can call at91_adc_touch_data_handler function
to start the work by schedule_work(&st->touch_st.workq).
If we remove the module which will call at91_adc_remove to
make cleanup, it will free indio_dev through iio_device_unregister but
quite a bit later. While the work mentioned above will be used. The
sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| at91_adc_workq_handler
at91_adc_remove |
iio_device_unregister(indio_dev) |
//free indio_dev a bit later |
| iio_push_to_buffers(indio_dev)
| //use indio_dev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in at91_adc_remove.
Fixes: 23ec2774f1 ("iio: adc: at91-sama5d2_adc: add support for position and pressure channels")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92452b1760 upstream.
The mask setting is 5 bits wide for the ad9434
(ref. data sheet register 0x18 FLEX_VREF). Apparently the settings
from ad9265 were copied by mistake when support for the device was added
to the driver.
Fixes: 4606d0f4b0 ("iio: adc: ad9467: add support for AD9434 high-speed ADC")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8f15d1df2 upstream.
The sensors IIS328DQ and H3LIS331DL share one configuration but
H3LIS331DL has different gain parameters, configs therefore
need to be split up.
The gain parameters for the IIS328DQ are 0.98, 1.95 and 3.91,
depending on the selected measurement range.
See sensor manuals, chapter 2.1 "mechanical characteristics",
parameter "Sensitivity".
Datasheet: https://www.st.com/resource/en/datasheet/iis328dq.pdf
Datasheet: https://www.st.com/resource/en/datasheet/h3lis331dl.pdf
Fixes: 46e33707fe ("iio: accel: add support for IIS328DQ variant")
Reviewed-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Signed-off-by: Markus Koeniger <markus.koeniger@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ff39d6de4 upstream.
fwnode_irq_get_byname() returns a negative value on failure; if a negative
value is returned, use it as `err` argument for dev_err_probe().
While at it, add a missing trailing newline to the dev_err_probe() error
message.
Fixes: df36de1367 ("iio: accel: add ADXL380 driver")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7880cb166 upstream.
Syzbot has found a deadlock (analyzed by Lance Yang):
1) Task (5749): Holds folio_lock, then tries to acquire i_mmap_rwsem(read lock).
2) Task (5754): Holds i_mmap_rwsem(write lock), then tries to acquire
folio_lock.
migrate_pages()
-> migrate_hugetlbs()
-> unmap_and_move_huge_page() <- Takes folio_lock!
-> remove_migration_ptes()
-> __rmap_walk_file()
-> i_mmap_lock_read() <- Waits for i_mmap_rwsem(read lock)!
hugetlbfs_fallocate()
-> hugetlbfs_punch_hole() <- Takes i_mmap_rwsem(write lock)!
-> hugetlbfs_zero_partial_page()
-> filemap_lock_hugetlb_folio()
-> filemap_lock_folio()
-> __filemap_get_folio <- Waits for folio_lock!
The migration path is the one taking locks in the wrong order according to
the documentation at the top of mm/rmap.c. So expand the scope of the
existing i_mmap_lock to cover the calls to remove_migration_ptes() too.
This is (mostly) how it used to be after commit c0d0381ade. That was
removed by 336bf30eb7 for both file & anon hugetlb pages when it should
only have been removed for anon hugetlb pages.
Link: https://lkml.kernel.org/r/20260109041345.3863089-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Fixes: 336bf30eb7 ("hugetlbfs: fix anon huge page migration race")
Reported-by: syzbot+2d9c96466c978346b55f@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/68e9715a.050a0220.1186a4.000d.GAE@google.com
Debugged-by: Lance Yang <lance.yang@linux.dev>
Acked-by: David Hildenbrand (Red Hat) <david@kernel.org>
Acked-by: Zi Yan <ziy@nvidia.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Byungchul Park <byungchul@sk.com>
Cc: Gregory Price <gourry@gourry.net>
Cc: Jann Horn <jannh@google.com>
Cc: Joshua Hahn <joshua.hahnjy@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Rakie Kim <rakie.kim@sk.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Ying Huang <ying.huang@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
