commit ae450e246e upstream.
This patch changes core_scsi3_pro_release() logic to allow an
existing AllRegistrants type reservation to be re-reserved by
any registered I_T nexus.
This addresses a issue where AllRegistrants type RESERVE was
receiving RESERVATION_CONFLICT status if dev_pr_res_holder did
not match the same I_T nexus, instead of just returning GOOD
status following spc4r34 Section 5.9.9:
"If the device server receives a PERSISTENT RESERVE OUT command
with RESERVE service action where the TYPE field and the SCOPE
field contain the same values as the existing type and scope
from a persistent reservation holder, it shall not make any
change to the existing persistent reservation and shall complete
the command with GOOD status."
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6c3c9baa0d upstream.
This patch fixes an issue with AllRegistrants reservations where
an unregister operation by the I_T nexus reservation holder would
incorrectly drop the reservation, instead of waiting until the
last active I_T nexus is unregistered as per SPC-4.
This includes updating __core_scsi3_complete_pro_release() to reset
dev->dev_pr_res_holder with another pr_reg for this special case,
as well as a new 'unreg' parameter to determine when the release
is occuring from an implicit unregister, vs. explicit RELEASE.
It also adds special handling in core_scsi3_free_pr_reg_from_nacl()
to release the left-over pr_res_holder, now that pr_reg is deleted
from pr_reg_list within __core_scsi3_complete_pro_release().
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d16ca7c519 upstream.
This patch fixes the usage of R_HOLDER bit for an All Registrants
reservation in READ_FULL_STATUS, where only the registration who
issued RESERVE was being reported as having an active reservation.
It changes core_scsi3_pri_read_full_status() to check ahead of the
list walk of active registrations to see if All Registrants is active,
and if so set R_HOLDER bit and scope/type fields for all active
registrations.
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit be8e89087e upstream.
The hardware range code values and list of valid ranges for the AI
subdevice is incorrect for several supported boards. The hardware range
code values for all boards except PCI-DAS4020/12 is determined by
calling `ai_range_bits_6xxx()` based on the maximum voltage of the range
and whether it is bipolar or unipolar, however it only returns the
correct hardware range code for the PCI-DAS60xx boards. For
PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar
ranges. For PCI-DAS64/Mx/16 it returns the wrong code for all the
ranges and the comedi range table is incorrect.
Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new
member `ai_range_codes` of `struct pcidas64_board` to map the comedi
range table indices to the hardware range codes. Use a new comedi range
table for the PCI-DAS64/Mx/16 boards (and the commented out variants).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 551c33e729 upstream.
Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c6c95ef4ce upstream.
We always unmap SGs with the same direction instead of unmapping
with the direction the mapping was done, fix that.
Fixes: 9a8b08fad2 ("IB/iser: Generalize iser_unmap_task_data and [...]")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e9a7faf11a upstream.
The MLX4_PROT_IB_IPV4 protocol should only be used with RoCEv2 and such.
Removing this wrong usage allows to run multicast applications over RoCE.
Fixes: d487ee7774 ("IB/mlx4: Use IBoE (RoCE) IP based GIDs in the port GID table")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0fb8bcf022 upstream.
The deadlock occurs in __uverbs_modify_qp: we take a lock (idr_read_qp)
and in case of failure in ib_resolve_eth_l2_attrs we don't release
it (put_qp_read). Fix that.
Fixes: ed4c54e5b4 ("IB/core: Resolve Ethernet L2 addresses when modifying QP")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c2be9dc0e0 upstream.
When marshaling a user path to the kernel struct ib_sa_path, we need
to zero smac and dmac and set the vlan id to the "no vlan" value.
This is to ensure that Ethernet attributes are not used with
InfiniBand QPs.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Signed-off-by: Ilya Nelkenbaum <ilyan@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ce363c2bcb upstream.
It seems that the same problems which lead to adding an rfkill blacklist and
putting the Lenovo Yoga 2 11 on it are also present on the Lenovo Yoga 2 13
and Lenovo Yoga 2 Pro too:
https://bugzilla.redhat.com/show_bug.cgi?id=1021036https://forums.lenovo.com/t5/Linux-Discussion/Yoga-2-13-not-Pro-Linux-Warning/m-p/1517612
Testing has shown that the firmware rfkill settings are persistent over
reboots. So blacklisting the driver is not good enough, if the wifi is blocked
at the firmware level the wifi needs to be explictly unblocked through the
ideapad-laptop interface.
And at least on the Lenovo Yoga 2 13 the VPCCMD_RF register which on devices
with hardware kill switch reports the hardware switch state, needs to be
explictly set to 1 (radio enabled / not blocked).
So this patch does 3 things to get proper rfkill handling on these models:
1) Instead of blacklisting the rfkill functionality, which means that people
with a firmware blocked wifi get stuck in that situation, ignore the value
reported by the not present hardware rfkill switch, as this is what is causing
ideapad-laptop to wrongly report all radios as hardware blocks. But do register
the rfkill interfaces so that the user can soft [un]block them.
2) On models without a hardware rfkill switch, explictly set VPCCMD_RF to 1
3) Drop the " 11" postfix from the dmi match string, as the entire Yoga 2
series is affected.
Yoga 2 11:
Reported-and-tested-by: Vincent Gerris <vgerris@gmail.com>
Yoga 2 13:
Tested-by: madls05 <http://ubuntuforums.org/showthread.php?t=2215044>
Yoga 2 Pro:
Reported-and-tested-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Cc: Gaudenz Steinlin <gaudenz@debian.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4c672e4b42 upstream.
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20
head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0
dev:port1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:100!
invalid opcode: 0000 [#1] SMP
Modules linked in: ixgbe(O)
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4
[...]
Call Trace:
<IRQ>
[<ffffffff80578226>] ? skb_put+0x3a/0x3b
[<ffffffff80612a5d>] ? add_grhead+0x45/0x8e
[<ffffffff80612e3a>] ? add_grec+0x394/0x3d4
[<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d
[<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45
[<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68
[<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182
[<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d
[<ffffffff8025112b>] ? irq_exit+0x4e/0xd3
[<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46
[<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6ead
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com>
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ebbeba120a upstream.
Fix attribute-creation race with userspace by using the default group
to create also the contingent gpio device attributes.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- all changes in drivers/gpio/gpiolib.c
- adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2061dcd6bf upstream.
I.e. one-to-many sockets in SCTP are not required to explicitly
call into connect(2) or sctp_connectx(2) prior to data exchange.
Instead, they can directly invoke sendmsg(2) and the SCTP stack
will automatically trigger connection establishment through 4WHS
via sctp_primitive_ASSOCIATE(). However, this in its current
implementation is racy: INIT is being sent out immediately (as
it cannot be bundled anyway) and the rest of the DATA chunks are
queued up for later xmit when connection is established, meaning
sendmsg(2) will return successfully. This behaviour can result
in an undesired side-effect that the kernel made the application
think the data has already been transmitted, although none of it
has actually left the machine, worst case even after close(2)'ing
the socket.
Instead, when the association from client side has been shut down
e.g. first gracefully through SCTP_EOF and then close(2), the
client could afterwards still receive the server's INIT_ACK due
to a connection with higher latency. This INIT_ACK is then considered
out of the blue and hence responded with ABORT as there was no
alive assoc found anymore. This can be easily reproduced f.e.
with sctp_test application from lksctp. One way to fix this race
is to wait for the handshake to actually complete.
The fix defers waiting after sctp_primitive_ASSOCIATE() and
sctp_primitive_SEND() succeeded, so that DATA chunks cooked up
from sctp_sendmsg() have already been placed into the output
queue through the side-effect interpreter, and therefore can then
be bundeled together with COOKIE_ECHO control chunks.
strace from example application (shortened):
socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...},
msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF
close(3) = 0
tcpdump before patch (fooling the application):
22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684]
22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591]
22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT]
tcpdump after patch:
14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729]
14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492]
14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...]
14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0]
14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...]
14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0]
14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...]
14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0]
14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN]
14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK]
14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE]
Looks like this bug is from the pre-git history museum. ;)
Fixes: 08707d5482df ("lksctp-2_5_31-0_5_1.patch")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a5a519b271 upstream.
In recent testing I had disabled CONFIG_IP_MULTIPLE_TABLES and as a result
when I ran "cat /proc/net/fib_trie" the main trie was displayed multiple
times. I found that the problem line of code was in the function
fib_trie_seq_next. Specifically the line below caused the indexes to go in
the opposite direction of our traversal:
h = tb->tb_id & (FIB_TABLE_HASHSZ - 1);
This issue was that the RT tables are defined such that RT_TABLE_LOCAL is ID
255, while it is located at TABLE_LOCAL_INDEX of 0, and RT_TABLE_MAIN is 254
with a TABLE_MAIN_INDEX of 1. This means that the above line will return 1
for the local table and 0 for main. The result is that fib_trie_seq_next
will return NULL at the end of the local table, fib_trie_seq_start will
return the start of the main table, and then fib_trie_seq_next will loop on
main forever as h will always return 0.
The fix for this is to reverse the ordering of the two tables. It has the
advantage of making it so that the tables now print in the same order
regardless of if multiple tables are enabled or not. In order to make the
definition consistent with the multiple tables case I simply masked the to
RT_TABLE_XXX values by (FIB_TABLE_HASHSZ - 1). This way the two table
layouts should always stay consistent.
Fixes: 93456b6 ("[IPV4]: Unify access to the routing tables")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6d00f37e49 upstream.
d1c7e29e8d (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.
Fixes: d1c7e29e8d "HID: i2c-hid: prevent buffer overflow in early IRQ"
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit db27ebb111 upstream.
Max unacked packets/bytes is an int while sizeof(long) was used in the
sysctl table.
This means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6b8d9117cc upstream.
The timeout entries are sizeof(int) rather than sizeof(long), which
means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e4940626de upstream.
The problem here is that we check:
if (dev >= SNDRV_CARDS)
Then we increment "dev".
if (!joystick_port[dev++])
Then we use it as an offset into a array with SNDRV_CARDS elements.
if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {
This has 3 effects:
1) If you use the module option to specify the joystick port then it has
to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
32 cards.
3) Static checkers will correctly complain that are off by one.
Fixes: db1005ec6f ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4ff0f034e9 upstream.
The right check for conf_reg to be invalid it testing against -1 not 0
as is done in the rest of the driver.
This fixes an oops that can be triggered by:
cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/*
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/pinctrl/freescale/pinctrl-imx.c ->
drivers/pinctrl/pinctrl-imx.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6f20e7f2e9 upstream.
When calling to early_setup(), we pick "boot_paca" up for the master CPU
and initialize that with initialise_paca(). At that point, the SLB
shadow buffer isn't populated yet. Updating the SLB shadow buffer should
corrupt what we had in physical address 0 where the trap instruction is
usually stored.
This hasn't been observed to cause any trouble in practice, but is
obviously fishy.
Fixes: 6f4441ef70 ("powerpc: Dynamically allocate slb_shadow from memblock")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2e9dcdae40 upstream.
In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 86d68a58d0 upstream.
The "> 0" here should ">= 0" so we free map_entries[0].
Fixes: 926172d460 ('efi: Export EFI runtime memory mapping to sysfs')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7d82bf3419 upstream.
If the call to devm_kzalloc() fails, nothing must be cleant up.
This was missed before because gpio_rcar_probe() had a "return"
statement after the first "goto err0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: df0c6c8023 ("gpio: rcar: Add minimal runtime PM support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7331ea474e upstream.
Commit f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0a280962dc upstream.
X-Coverup: just ask spender
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7e0e953bb0 upstream.
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0db59e5929 upstream.
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1467559232 upstream.
The output of KDB 'summary' command should report MemTotal, MemFree
and Buffers output in kB. Current codes report in unit of pages.
A define of K(x) as
is defined in the code, but not used.
This patch would apply the define to convert the values to kB.
Please include me on Cc on replies. I do not subscribe to linux-kernel.
Signed-off-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ca5d25642e upstream.
Export the _save_msa asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m and
CONFIG_CPU_HAS_MSA=y due to commit f798217dfd ("KVM: MIPS: Don't leak
FPU/DSP to guest"):
ERROR: "_save_msa" [arch/mips/kvm/kvm.ko] undefined!
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3ce465e04b upstream.
Export the _save_fp asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m due to commit
f798217dfd ("KVM: MIPS: Don't leak FPU/DSP to guest"):
ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9260/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7eb71e0351 upstream.
It turns out it's possible to get __remove_osd() called twice on the
same OSD. That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory. One scenario that I was able to reproduce is as follows:
<osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
osd_reset()
<osdmap - osd3 down>
ceph_osdc_handle_map()
<takes map_sem>
kick_requests()
<takes request_mutex>
reset_changed_osds()
__reset_osd()
__remove_osd()
<releases request_mutex>
<releases map_sem>
<takes map_sem>
<takes request_mutex>
__kick_osd_requests()
__reset_osd()
__remove_osd() <-- !!!
A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().
Fixes: http://tracker.ceph.com/issues/8087
Cc: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cc9f1f518c upstream.
No reason to use BUG_ON for osd request list assertions.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7c6e6fc53e upstream.
It is important that both regular and lingering requests lists are
empty when the OSD is removed.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4e7c22d447 upstream.
The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.
The affected function is randomize_stack_top() in file
"fs/binfmt_elf.c":
static unsigned long randomize_stack_top(unsigned long stack_top)
{
unsigned int random_variable = 0;
if ((current->flags & PF_RANDOMIZE) &&
!(current->personality & ADDR_NO_RANDOMIZE)) {
random_variable = get_random_int() & STACK_RND_MASK;
random_variable <<= PAGE_SHIFT;
}
return PAGE_ALIGN(stack_top) + random_variable;
return PAGE_ALIGN(stack_top) - random_variable;
}
Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):
random_variable <<= PAGE_SHIFT;
then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.
These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).
This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and
stack_maxrandom_size().
The successful fix can be tested with:
$ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0 [stack]
7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0 [stack]
7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0 [stack]
7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0 [stack]
...
Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.
Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: Ismael Ripoll <iripoll@upv.es>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: CVE-2015-1593
Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.net
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 61882b6317 upstream.
The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:
WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()
This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 22aa66a3ee upstream.
When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero. Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.
pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences s->origin. These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.
This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2bec1f4a88 upstream.
The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.
dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.
There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.
To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 29183a70b0 upstream.
Additional validation of adjtimex freq values to avoid
potential multiplication overflows were added in commit
5e5aeb4367 (time: adjtimex: Validate the ADJ_FREQUENCY values)
Unfortunately the patch used LONG_MAX/MIN instead of
LLONG_MAX/MIN, which was fine on 64-bit systems, but being
much smaller on 32-bit systems caused false positives
resulting in most direct frequency adjustments to fail w/
EINVAL.
ntpd only does direct frequency adjustments at startup, so
the issue was not as easily observed there, but other time
sync applications like ptpd and chrony were more effected by
the bug.
See bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=92481https://bugzilla.redhat.com/show_bug.cgi?id=1188074
This patch changes the checks to use LLONG_MAX for
clarity, and additionally the checks are disabled
on 32-bit systems since LLONG_MAX/PPM_SCALE is always
larger then the 32-bit long freq value, so multiplication
overflows aren't possible there.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: George Joseph <george.joseph@fairview5.com>
Tested-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Link: http://lkml.kernel.org/r/1423553436-29747-1-git-send-email-john.stultz@linaro.org
[ Prettified the changelog and the comments a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5e5aeb4367 upstream.
Verify that the frequency value from userspace is valid and makes sense.
Unverified values can cause overflows later on.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[jstultz: Fix up bug for negative values and drop redunent cap check]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8d1e5a1a1c upstream.
With task_blocks_on_rt_mutex() returning early -EDEADLK we never
add the waiter to the waitqueue. Later, we try to remove it via
remove_waiter() and go boom in rt_mutex_top_waiter() because
rb_entry() gives a NULL pointer.
( Tested on v3.18-RT where rtmutex is used for regular mutex and I
tried to get one twice in a row. )
Not sure when this started but I guess 397335f004 ("rtmutex: Fix
deadlock detector for real") or commit 3d5c9340d1 ("rtmutex:
Handle deadlock detection smarter").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1424187823-19600-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 26ac107378 upstream.
Commit a7854487cd:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit acac4108df upstream.
The "addi" instruction will trap on overflows which is not something
we need in this code, so we replace that with "addiu".
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00430.html
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 98a833c1fa upstream.
The "add" instruction is actually a macro in binutils and depending on
the size of the immediate it can expand to an "addi" instruction.
However, the "addi" instruction traps on overflows which is not
something we want on address calculation.
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00121.html
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 18c0b82a3e upstream.
This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.
These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3b524a683a upstream.
Fix SCSI generic read() incorrectly returning success after detecting an
error.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f76a610a8b upstream.
In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.
[ 29.406183] ------------[ cut here ]------------
[ 29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: Minh Tran <minh.tran@emulex.com>
Fixes: 6733b39a13
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb71f8a5e3 upstream.
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
