This supports I2C2 bus on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports Ethernet AVB on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7795 SoC based H3ULCB low cost
board.
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The audio-dmac nodes used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is supported for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a7795.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7795 has 9 VSP instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the VSP2s.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have to set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch also adds a regulator node for USB2.0 to handle VBUS on/off
by the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide nodes for the FCP devices dedicated to the FDP device channels.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With git commit 0eab11c7e0
"s390/vx: allow to include vx-insn.h with .include"
and an older gcc we get errors like this:
{standard input}:6: Error: can't open asm/vx-insn.h for reading:
No such file or directory
arch/s390/kernel/fpu.c:57: Error: Unrecognized opcode: `vstm'
To solve this issue simply add the path to arch/s390/include to
all assembler runs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Static analysis with cppcheck detected that ret is not initialized
and hence garbage is potentially being returned in the case where
prng_data->ppnows.reseed_counter <= prng_reseed_limit.
Thanks to Martin Schwidefsky for spotting a mistake in my original
fix.
Fixes: 0177db01ad ("s390/crypto: simplify return code handling")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The workqueue "appldata_wq" has been replaced with an ordered dedicated
workqueue.
WQ_MEM_RECLAIM has not been set since the workqueue is not being used on
a memory reclaim path.
The adapter->work_queue queues multiple work items viz
&adapter->scan_work, &port->rport_work, &adapter->ns_up_work,
&adapter->stat_work, adapter->work_queue, &adapter->events.work,
&port->gid_pn_work, &port->test_link_work. Hence, an ordered
dedicated workqueue has been used.
WQ_MEM_RECLAIM has been set to ensure forward progress under memory
pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Yanqiu Zhang reported kernel panic when using mbm event
on system where CQM is detected but without mbm event
support, like with perf:
# perf stat -e 'intel_cqm/event=3/' -a
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffff8100d64c>] update_sample+0xbc/0xe0
...
<IRQ>
[<ffffffff8100d688>] __intel_mbm_event_init+0x18/0x20
[<ffffffff81113d6b>] flush_smp_call_function_queue+0x7b/0x160
[<ffffffff81114853>] generic_smp_call_function_single_interrupt+0x13/0x60
[<ffffffff81052017>] smp_call_function_interrupt+0x27/0x40
[<ffffffff816fb06c>] call_function_interrupt+0x8c/0xa0
...
The reason is that we currently allow to init mbm event
even if mbm support is not detected. Adding checks for
both cqm and mbm events and support into cqm's event_init.
Fixes: 33c3cc7acf ("perf/x86/mbm: Add Intel Memory B/W Monitoring enumeration and init")
Reported-by: Yanqiu Zhang <yanqzhan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1473089407-21857-1-git-send-email-jolsa@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The compound PE is created to accommodate the devices attached to
one specific PCI bus that consume multiple M64 segments. The compound
PE is made up of one master PE and possibly multiple slave PEs. The
slave PEs should be destroyed when releasing the master PE. A kernel
crash happens when derferencing @pe->pdev on releasing the slave PE
in pnv_ioda_deconfigure_pe().
# echo 0 > /sys/bus/pci/slots/C7/power
iommu: Removing device 0000:01:00.1 from group 0
iommu: Removing device 0000:01:00.0 from group 0
Unable to handle kernel paging request for data at address 0x00000010
Faulting instruction address: 0xc00000000005d898
cpu 0x1: Vector: 300 (Data Access) at [c000000fe8217620]
pc: c00000000005d898: pnv_ioda_release_pe+0x288/0x610
lr: c00000000005dbdc: pnv_ioda_release_pe+0x5cc/0x610
sp: c000000fe82178a0
msr: 9000000000009033
dar: 10
dsisr: 40000000
current = 0xc000000fe815ab80
paca = 0xc00000000ff00400 softe: 0 irq_happened: 0x01
pid = 2709, comm = sh
Linux version 4.8.0-rc5-gavin-00006-g745efdb (gwshan@gwshan) \
(gcc version 4.9.3 (Buildroot 2016.02-rc2-00093-g5ea3bce) ) #586 SMP \
Tue Sep 6 13:37:29 AEST 2016
enter ? for help
[c000000fe8217940] c00000000005d684 pnv_ioda_release_pe+0x74/0x610
[c000000fe82179e0] c000000000034460 pcibios_release_device+0x50/0x70
[c000000fe8217a10] c0000000004aba80 pci_release_dev+0x50/0xa0
[c000000fe8217a40] c000000000704898 device_release+0x58/0xf0
[c000000fe8217ac0] c000000000470510 kobject_release+0x80/0xf0
[c000000fe8217b00] c000000000704dd4 put_device+0x24/0x40
[c000000fe8217b20] c0000000004af94c pci_remove_bus_device+0x12c/0x150
[c000000fe8217b60] c000000000034244 pci_hp_remove_devices+0x94/0xd0
[c000000fe8217ba0] c0000000004ca444 pnv_php_disable_slot+0x64/0xb0
[c000000fe8217bd0] c0000000004c88c0 power_write_file+0xa0/0x190
[c000000fe8217c50] c0000000004c248c pci_slot_attr_store+0x3c/0x60
[c000000fe8217c70] c0000000002d6494 sysfs_kf_write+0x94/0xc0
[c000000fe8217cb0] c0000000002d50f0 kernfs_fop_write+0x180/0x260
[c000000fe8217d00] c0000000002334a0 __vfs_write+0x40/0x190
[c000000fe8217d90] c000000000234738 vfs_write+0xc8/0x240
[c000000fe8217de0] c000000000236250 SyS_write+0x60/0x110
[c000000fe8217e30] c000000000009524 system_call+0x38/0x108
It fixes the kernel crash by bypassing releasing resources (DMA,
IO and memory segments, PELTM) because there are no resources assigned
to the slave PE.
Fixes: c5f7700bbd ("powerpc/powernv: Dynamically release PE")
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When using the OPAL ICP backend we incorrectly pass Linux CPU numbers
rather than HW CPU numbers to OPAL.
Fixes: d74361881f ("powerpc/xics: Add ICP OPAL backend")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On ppc64le, builds with CONFIG_KEXEC=n fail with:
arch/powerpc/platforms/pseries/setup.c: In function ‘pseries_big_endian_exceptions’:
arch/powerpc/platforms/pseries/setup.c:403:13: error: implicit declaration of function ‘kdump_in_progress’
if (rc && !kdump_in_progress())
This is because pseries/setup.c includes <linux/kexec.h>, but
kdump_in_progress() is defined in <asm/kexec.h>. This is a problem
because the former only includes the latter if CONFIG_KEXEC_CORE=y.
Fix it by including <asm/kexec.h> directly, as is done in powernv/setup.c.
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds to enable the ARM Performance Monitor Units for rk3399.
ARM cores often have a PMU for counting cpu and cache events like cache
misses and hits.
This uses the new interrupt-partition mechanism to allow the two pmu
instances to use the per-cpu interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the interrupts cells value for 4, and the 4th cell is zero.
Due to the doc[0] said:" the system requires describing PPI affinity,
then the value must be at least 4"
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
interrupt types other than PPI or PPIs that are not partitionned,
this cell must be zero. See the "ppi-partitions" node description
below.
[0]:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.
The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.
This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TSC_OFFSET will be adjusted if discovers TSC backward during vCPU load.
The preemption timer, which relies on the guest tsc to reprogram its
preemption timer value, is also reprogrammed if vCPU is scheded in to
a different pCPU. However, the current implementation reprogram preemption
timer before TSC_OFFSET is adjusted to the right value, resulting in the
preemption timer firing prematurely.
This patch fix it by adjusting TSC_OFFSET before reprogramming preemption
timer if TSC backward.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krċmář <rkrcmar@redhat.com>
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, enabling stacktrace of a kprobe events generates warning:
echo stacktrace > /sys/kernel/debug/tracing/trace_options
echo "p xhci_irq" > /sys/kernel/debug/tracing/kprobe_events
echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable
save_stack_trace_regs() not implemented yet.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../kernel/stacktrace.c:74 save_stack_trace_regs+0x3c/0x48
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc4-dirty #5128
Hardware name: ARM Juno development board (r1) (DT)
task: ffff800975dd1900 task.stack: ffff800975ddc000
PC is at save_stack_trace_regs+0x3c/0x48
LR is at save_stack_trace_regs+0x3c/0x48
pc : [<ffff000008126c64>] lr : [<ffff000008126c64>] pstate: 600003c5
sp : ffff80097ef52c00
Call trace:
save_stack_trace_regs+0x3c/0x48
__ftrace_trace_stack+0x168/0x208
trace_buffer_unlock_commit_regs+0x5c/0x7c
kprobe_trace_func+0x308/0x3d8
kprobe_dispatcher+0x58/0x60
kprobe_breakpoint_handler+0xbc/0x18c
brk_handler+0x50/0x90
do_debug_exception+0x50/0xbc
This patch implements save_stack_trace_regs(), so that stacktrace of a
kprobe events can be obtained.
After this patch, there is no warning and we can see the stacktrace for
kprobe events in trace buffer.
more /sys/kernel/debug/tracing/trace
<idle>-0 [004] d.h. 1356.000496: p_xhci_irq_0:(xhci_irq+0x0/0x9ac)
<idle>-0 [004] d.h. 1356.000497: <stack trace>
=> xhci_irq
=> __handle_irq_event_percpu
=> handle_irq_event_percpu
=> handle_irq_event
=> handle_fasteoi_irq
=> generic_handle_irq
=> __handle_domain_irq
=> gic_handle_irq
=> el1_irq
=> arch_cpu_idle
=> default_idle_call
=> cpu_startup_entry
=> secondary_start_kernel
=>
Tested-by: David A. Long <dave.long@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Define the generic R8A7792 part of the QSPI device node.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the QSPI clock in the R8A7792 device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the CAN0/1 device nodes...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When removing the non-existing thermal clock I forgot to remove its
parent from the node's "clocks" property -- this led to a wrong PWM
clock's parent clock.
Fixes: 2a29f9d6fe ("ARM: dts: r8a7794: add MSTP5 clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the RZ/A1 based development board (RSK).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>